258 lines
6.2 KiB
INI
258 lines
6.2 KiB
INI
# This file allows user to override the factory
|
|
# defaults for the WLAN Driver
|
|
|
|
# Enable IMPS or not
|
|
gEnableImps=1
|
|
|
|
# Enable/Disable Idle Scan
|
|
gEnableIdleScan=0
|
|
|
|
# Increase sleep duration (seconds) during IMPS
|
|
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
|
|
# unnecessary if Idle Scan is disabled.
|
|
gImpsModSleepTime=0
|
|
|
|
# Enable BMPS or not
|
|
gEnableBmps=1
|
|
|
|
# Enable Close Loop or not
|
|
gEnableCloseLoop=1
|
|
|
|
# Enable suspend or not
|
|
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
|
|
gEnableSuspend=3
|
|
|
|
# Phy Mode (auto, b, g, n, etc)
|
|
gDot11Mode=0
|
|
|
|
# Handoff Enable(1) Disable(0)
|
|
gEnableHandoff=0
|
|
|
|
# CSR Roaming Enable(1) Disable(0)
|
|
gRoamingTime=0
|
|
|
|
# Assigned MAC Addresses - This will be used until NV items are in place
|
|
# Each byte of MAC address is represented in Hex format as XX
|
|
Intf0MacAddress=000AF58989FF
|
|
Intf1MacAddress=000AF58989FE
|
|
Intf2MacAddress=000AF58989FD
|
|
Intf3MacAddress=000AF58989FC
|
|
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
|
InfraUapsdVoSrvIntv=0
|
|
InfraUapsdViSrvIntv=0
|
|
InfraUapsdBeSrvIntv=0
|
|
InfraUapsdBkSrvIntv=0
|
|
|
|
# Enable Firmware RSSI monitoring for roaming
|
|
gEnableFWRssiMonitoring=1
|
|
|
|
# Make 1x1 the default antenna configuration
|
|
gNumRxAnt=1
|
|
|
|
# Beacon filtering frequency (unit in beacon intervals)
|
|
gNthBeaconFilter=50
|
|
|
|
# Enable WAPI or not
|
|
# WAPIIsEnabled=0
|
|
|
|
# Flags to filter Mcast and Bcast RX packets.
|
|
# Value 0: No filtering, 1: Filter all Multicast.
|
|
# 2: Filter all Broadcast. 3: Filter all Mcast and Bcast
|
|
McastBcastFilter=3
|
|
|
|
# Flag to enable Active mode offload
|
|
gEnableActiveModeOffload=1
|
|
|
|
# Flag to enable HostARPOffload feature or not
|
|
hostArpOffload=1
|
|
|
|
# Flag to enable Host IPv6 NS Offload feature or not
|
|
hostNSOffload=1
|
|
|
|
#SoftAP Related Parameters
|
|
# AP MAc addr (obsolete)
|
|
gAPMacAddr=000AF58989EF
|
|
|
|
# Enable Random BSSID
|
|
gEnableApRandomBssid=1
|
|
|
|
# 802.11n Protection flag
|
|
gEnableApProt=1
|
|
|
|
# Enable OBSS protection
|
|
gEnableApOBSSProt=0
|
|
|
|
# Enable/Disable UAPSD for SoftAP
|
|
gEnableApUapsd=1
|
|
|
|
# Fixed Rate
|
|
gFixedRate=0
|
|
|
|
# Maximum Tx power
|
|
# gTxPowerCap=30
|
|
|
|
# Fragmentation Threshold
|
|
# gFragmentationThreshold=2346
|
|
|
|
# RTS threshold
|
|
RTSThreshold=2347
|
|
|
|
# Intra-BSS forward
|
|
gDisableIntraBssFwd=0
|
|
|
|
# WMM Enable/Disable
|
|
WmmIsEnabled=0
|
|
|
|
# 802.11d support
|
|
g11dSupportEnabled=0
|
|
|
|
# CCX Support and fast transition
|
|
CcxEnabled=0
|
|
FastTransitionEnabled=1
|
|
ImplicitQosIsEnabled=1
|
|
gNeighborScanTimerPeriod=200
|
|
|
|
gNeighborLookupThreshold=76
|
|
gNeighborReassocThreshold=81
|
|
|
|
gNeighborScanChannelMinTime=20
|
|
gNeighborScanChannelMaxTime=30
|
|
gMaxNeighborReqTries=3
|
|
|
|
# Legacy (non-CCX, non-802.11r) Fast Roaming Support
|
|
# To enable, set FastRoamEnabled=1, gEnableFWRssiMonitoring=1, FastTransitionEnabled=1
|
|
# To disable, set FastRoamEnabled=0, gEnableFWRssiMonitoring=0, FastTransitionEnabled=0
|
|
FastRoamEnabled=1
|
|
|
|
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
|
|
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
|
|
#the RSSI of the new/roamable AP should be for roaming
|
|
RoamRssiDiff=3
|
|
|
|
#Configure the RSSI gap that will be used to partition/categorize width of
|
|
#each individual category (aka bucket).
|
|
gRssiCatGap=5
|
|
|
|
# SAP Country code
|
|
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
|
|
# Example
|
|
# US Indoor, USI
|
|
# Korea Outdoor, KRO
|
|
# Japan without optional byte, JP
|
|
# France without optional byte, FR
|
|
#gAPCntryCode=USI
|
|
|
|
#Short Guard Interval Enable/disable
|
|
gShortGI20Mhz=1
|
|
gShortGI40Mhz=1
|
|
|
|
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
|
|
gAPAutoShutOff=0
|
|
|
|
# SAP auto channel selection configuration
|
|
# 0 = disable auto channel selection
|
|
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
|
|
gApAutoChannelSelection=0
|
|
|
|
# Listen Energy Detect Mode Configuration
|
|
# Valid values 0-128
|
|
# 128 means disable Energy Detect feature
|
|
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
|
|
# 10-128 are reserved.
|
|
# The EDET threshold mapping is as follows in 3dB step:
|
|
# 0 = -60 dBm
|
|
# 1 = -63 dBm
|
|
# 2 = -66 dBm
|
|
# ...
|
|
# 7 = -81 dBm
|
|
# 8 = -84 dBm
|
|
# 9 = -87 dBm
|
|
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
|
|
#
|
|
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
|
|
#
|
|
gEnablePhyAgcListenMode=128
|
|
|
|
#Preferred band (both or 2.4 only or 5 only)
|
|
BandCapability=0
|
|
|
|
#Forced Device Listen Interval in multiples of DTIM Period aligned to DTIM
|
|
gEnableModulatedDTIM=3
|
|
|
|
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
|
|
enableBeaconEarlyTermination=1
|
|
beaconEarlyTerminationWakeInterval=11
|
|
|
|
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
|
|
gEnableBtAmp=0
|
|
|
|
#Preferred channel to start BT AMP AP mode (0 means, any channel)
|
|
BtAmpPreferredChannel=0
|
|
|
|
#SOFTAP Channel Range selection
|
|
gAPChannelSelectStartChannel=1
|
|
gAPChannelSelectEndChannel=11
|
|
|
|
#SOFTAP Channel Range selection Operating band
|
|
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
|
|
gAPChannelSelectOperatingBand=0
|
|
|
|
#Enable Keep alive with non-zero period value
|
|
gStaKeepAlivePeriod = 25
|
|
|
|
#If set will start with active scan after driver load, otherwise will start with
|
|
#passive scan to find out the domain
|
|
gEnableBypass11d=1
|
|
|
|
#If set to 0, will not scan DFS channels
|
|
gEnableDFSChnlScan=1
|
|
|
|
# Enable logp/SSR
|
|
gEnableLogp=1
|
|
|
|
# Enable HT40
|
|
gChannelBondingMode5GHz=1
|
|
|
|
# Enable Automatic Tx Power control
|
|
gEnableAutomaticTxPowerControl=1
|
|
|
|
# Derive P2P MAC address from primary MAC address
|
|
isP2pDeviceAddrAdministrated=1
|
|
|
|
# Disable channel 165 for Indonesia
|
|
gIgnore_Chan165=1
|
|
|
|
btcStaticLenLeBt=120000
|
|
btcStaticLenLeWlan=30000
|
|
|
|
#Data Inactivity Timeout when in powersave (in ms)
|
|
gDataInactivityTimeout=200
|
|
|
|
gCountryCodePriority=1
|
|
|
|
gNumChanCombinedConc=255
|
|
|
|
# TDLS configuration
|
|
gEnableTDLSSupport=1
|
|
gEnableTDLSImplicitTrigger=1
|
|
gTDLSExternalControl=1
|
|
gTDLSTxStatsPeriod=500
|
|
gTDLSTxPacketThreshold=10
|
|
gTDLSDiscoveryPeriod=20000
|
|
gTDLSMaxDiscoveryAttempt=5
|
|
gTDLSIdleTimeout=40000
|
|
gTDLSRssiHysteresis=100
|
|
gTDLSRSSITriggerThreshold=-60
|
|
gTDLSIdlePacketThreshold=5
|
|
gTDLSRSSITeardownThreshold=-70
|
|
|
|
# Enable IPv6 RA filtering
|
|
gMCAddrListEnable=1
|
|
|
|
# TheCrazyLex@PA limit max AP peers to 10 to prevent overloading
|
|
gSoftApMaxPeers=10
|
|
|
|
END
|
|
# Note: Configuration parser would not read anything past the END marker
|