mirror of
https://github.com/team-infusion-developers/android_device_samsung_msm8976-common.git
synced 2024-11-07 06:19:20 +00:00
msm8976-common: Remove unused WLAN config
Change-Id: Ibdf90ee8dee990e112bcb103cb88ec2705c383bf
This commit is contained in:
syphyr
Łukasz Patron
parent
eb0bd0ac80
commit
37954d7869
2 changed files with 1 additions and 704 deletions
|
|
@ -283,8 +283,7 @@ PRODUCT_PACKAGES += \
|
|||
# WCNSS
|
||||
PRODUCT_COPY_FILES += \
|
||||
$(LOCAL_PATH)/wifi/WCNSS_cfg.dat:$(TARGET_COPY_OUT_VENDOR)/firmware/wlan/qca_cld/WCNSS_cfg.dat \
|
||||
$(LOCAL_PATH)/wifi/WCNSS_qcom_cfg.ini:$(TARGET_COPY_OUT_VENDOR)/firmware/wlan/qca_cld/WCNSS_qcom_cfg.ini \
|
||||
$(LOCAL_PATH)/wifi/WCNSS_qcom_sdio_cfg.ini:$(TARGET_COPY_OUT_VENDOR)/etc/wifi/WCNSS_qcom_sdio_cfg.ini
|
||||
$(LOCAL_PATH)/wifi/WCNSS_qcom_cfg.ini:$(TARGET_COPY_OUT_VENDOR)/firmware/wlan/qca_cld/WCNSS_qcom_cfg.ini
|
||||
|
||||
# WiFi HAL
|
||||
PRODUCT_PACKAGES += \
|
||||
|
|
|
|||
|
|
@ -1,702 +0,0 @@
|
|||
# This file allows user to override the factory
|
||||
|
||||
# defaults for the WLAN Driver
|
||||
|
||||
|
||||
# Enable IMPS or not
|
||||
gEnableImps=1
|
||||
|
||||
# Enable/Disable Idle Scan
|
||||
gEnableIdleScan=0
|
||||
|
||||
|
||||
# Increase sleep duration (seconds) during IMPS
|
||||
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
|
||||
# unnecessary if Idle Scan is disabled.
|
||||
gImpsModSleepTime=0
|
||||
|
||||
|
||||
# Enable BMPS or not
|
||||
gEnableBmps=1
|
||||
|
||||
# Enable suspend or not
|
||||
|
||||
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
|
||||
|
||||
gEnableSuspend=3
|
||||
|
||||
# Phy Mode (auto, b, g, n, etc)
|
||||
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
|
||||
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
|
||||
# 7 = 11b only 8 = 11ac only.
|
||||
gDot11Mode=0
|
||||
|
||||
|
||||
# CSR Roaming Enable(1) Disable(0)
|
||||
|
||||
gRoamingTime=0
|
||||
|
||||
|
||||
# Assigned MAC Addresses - This will be used until NV items are in place
|
||||
|
||||
# Each byte of MAC address is represented in Hex format as XX
|
||||
|
||||
Intf0MacAddress=000AF58989FF
|
||||
Intf1MacAddress=000AF58989FE
|
||||
Intf2MacAddress=000AF58989FD
|
||||
|
||||
Intf3MacAddress=000AF58989FC
|
||||
|
||||
|
||||
# UAPSD service interval for VO,VI, BE, BK traffic
|
||||
|
||||
InfraUapsdVoSrvIntv=0
|
||||
|
||||
InfraUapsdViSrvIntv=0
|
||||
|
||||
InfraUapsdBeSrvIntv=0
|
||||
|
||||
InfraUapsdBkSrvIntv=0
|
||||
|
||||
# Flag to allow STA send AddTspec even when ACM is Off
|
||||
gAddTSWhenACMIsOff=1
|
||||
|
||||
# Make 1x1 the default antenna configuration
|
||||
|
||||
gNumRxAnt=1
|
||||
|
||||
|
||||
# Beacon filtering frequency (unit in beacon intervals)
|
||||
|
||||
gNthBeaconFilter=50
|
||||
|
||||
|
||||
# Enable WAPI or not
|
||||
|
||||
# WAPIIsEnabled=0
|
||||
|
||||
|
||||
# Flags to filter Mcast abd Bcast RX packets.
|
||||
|
||||
# Value 0: No filtering, 1: Filter all Multicast.
|
||||
|
||||
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
|
||||
|
||||
McastBcastFilter=3
|
||||
|
||||
|
||||
#Flag to enable HostARPOffload feature or not
|
||||
|
||||
hostArpOffload=1
|
||||
|
||||
#Flag to enable TCPChkSumOffld feature or not
|
||||
|
||||
gEnableTCPChkSumOffld=1
|
||||
|
||||
#Flag to enable HostNSOffload feature or not
|
||||
|
||||
hostNSOffload=1
|
||||
|
||||
#Flag to enable IPChkSumOffld feature or not
|
||||
|
||||
gEnableIPChecksumOffload=1
|
||||
|
||||
#SoftAP Related Parameters
|
||||
gSoftApMaxPeers=10
|
||||
|
||||
# AP MAc addr
|
||||
|
||||
gAPMacAddr=000AF589dcab
|
||||
|
||||
|
||||
# 802.11n Protection flag
|
||||
|
||||
gEnableApProt=1
|
||||
|
||||
|
||||
#Enable OBSS protection
|
||||
|
||||
gEnableApOBSSProt=1
|
||||
|
||||
|
||||
#Enable/Disable UAPSD for SoftAP
|
||||
|
||||
gEnableApUapsd=1
|
||||
|
||||
|
||||
# Fixed Rate
|
||||
|
||||
gFixedRate=0
|
||||
|
||||
|
||||
# Maximum Tx power
|
||||
|
||||
# gTxPowerCap=30
|
||||
|
||||
|
||||
# Fragmentation Threshold
|
||||
|
||||
# gFragmentationThreshold=2346
|
||||
|
||||
|
||||
# RTS threshold
|
||||
|
||||
RTSThreshold=1048576
|
||||
|
||||
|
||||
# Intra-BSS forward
|
||||
|
||||
gDisableIntraBssFwd=0
|
||||
|
||||
|
||||
# WMM Enable/Disable
|
||||
|
||||
WmmIsEnabled=0
|
||||
|
||||
|
||||
# 802.11d support
|
||||
|
||||
g11dSupportEnabled=0
|
||||
|
||||
# 802.11h support
|
||||
|
||||
g11hSupportEnabled=1
|
||||
|
||||
# DFS Master Capability
|
||||
gEnableDFSMasterCap=1
|
||||
|
||||
|
||||
|
||||
# ESE Support and fast transition
|
||||
|
||||
EseEnabled=1
|
||||
ImplicitQosIsEnabled=0
|
||||
gNeighborScanTimerPeriod=200
|
||||
|
||||
gNeighborLookupThreshold=76
|
||||
gNeighborReassocThreshold=81
|
||||
|
||||
gNeighborScanChannelMinTime=20
|
||||
gNeighborScanChannelMaxTime=30
|
||||
gMaxNeighborReqTries=3
|
||||
|
||||
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
||||
# To enable, set FastRoamEnabled=1
|
||||
# To disable, set FastRoamEnabled=0
|
||||
FastRoamEnabled=1
|
||||
|
||||
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
|
||||
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
|
||||
#the RSSI of the new/roamable AP should be for roaming
|
||||
RoamRssiDiff=3
|
||||
|
||||
# If the RSSI of any available candidate is better than currently associated
|
||||
# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
|
||||
# registering for reassoc threshold).
|
||||
# NOTE: Value of 0 means that we would register for reassoc threshold.
|
||||
gImmediateRoamRssiDiff=10
|
||||
|
||||
# To enable, set gRoamIntraBand=1 (Roaming within band)
|
||||
# To disable, set gRoamIntraBand=0 (Roaming across band)
|
||||
gRoamIntraBand=0
|
||||
|
||||
# SAP Country code
|
||||
|
||||
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
|
||||
|
||||
# Example
|
||||
|
||||
# US Indoor, USI
|
||||
|
||||
# Korea Outdoor, KRO
|
||||
|
||||
# Japan without optional byte, JP
|
||||
|
||||
# France without optional byte, FR
|
||||
|
||||
#gAPCntryCode=USI
|
||||
|
||||
|
||||
#Short Guard Interval Enable/disable
|
||||
|
||||
gShortGI20Mhz=1
|
||||
|
||||
gShortGI40Mhz=1
|
||||
|
||||
|
||||
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
|
||||
|
||||
gAPAutoShutOff=0
|
||||
|
||||
#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
|
||||
gWlanAutoShutdown = 0
|
||||
|
||||
|
||||
# Listen Energy Detect Mode Configuration
|
||||
|
||||
# Valid values 0-128
|
||||
|
||||
# 128 means disable Energy Detect feature
|
||||
|
||||
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
|
||||
|
||||
# 10-128 are reserved.
|
||||
|
||||
# The EDET threshold mapping is as follows in 3dB step:
|
||||
|
||||
# 0 = -60 dBm
|
||||
|
||||
# 1 = -63 dBm
|
||||
|
||||
# 2 = -66 dBm
|
||||
|
||||
# ...
|
||||
|
||||
# 7 = -81 dBm
|
||||
|
||||
# 8 = -84 dBm
|
||||
|
||||
# 9 = -87 dBm
|
||||
|
||||
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
|
||||
|
||||
#
|
||||
|
||||
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
|
||||
|
||||
#
|
||||
|
||||
gEnablePhyAgcListenMode=128
|
||||
|
||||
|
||||
#Preferred band (both or 2.4 only or 5 only)
|
||||
|
||||
BandCapability=0
|
||||
|
||||
|
||||
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
|
||||
|
||||
enableBeaconEarlyTermination=0
|
||||
|
||||
beaconEarlyTerminationWakeInterval=3
|
||||
|
||||
|
||||
#Channel Bonding
|
||||
gChannelBondingMode5GHz=1
|
||||
|
||||
|
||||
#Enable Keep alive with non-zero period value
|
||||
|
||||
gStaKeepAlivePeriod = 30
|
||||
|
||||
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
||||
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
|
||||
#For both active and power save clients.
|
||||
|
||||
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
|
||||
#If doesn't honor for 5 seconds then DUT remove client.
|
||||
|
||||
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
|
||||
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
|
||||
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
||||
|
||||
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
|
||||
#where we send NULL frame.
|
||||
|
||||
gApLinkMonitorPeriod = 30
|
||||
|
||||
gGoLinkMonitorPeriod = 10
|
||||
|
||||
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
|
||||
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
|
||||
|
||||
|
||||
gGoKeepAlivePeriod = 3
|
||||
|
||||
gApKeepAlivePeriod = 10
|
||||
|
||||
|
||||
#If set will start with active scan after driver load, otherwise will start with
|
||||
|
||||
#passive scan to find out the domain
|
||||
|
||||
gEnableBypass11d=1
|
||||
|
||||
|
||||
#If set to 0, will not scan DFS channels
|
||||
|
||||
gEnableDFSChnlScan=1
|
||||
|
||||
# Enable DFS channel roam
|
||||
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
|
||||
gAllowDFSChannelRoam=1
|
||||
|
||||
gVhtChannelWidth=2
|
||||
|
||||
|
||||
# Enable Automatic Tx Power control
|
||||
|
||||
gEnableAutomaticTxPowerControl=1
|
||||
|
||||
# 0 for OLPC 1 for CLPC and SCPC
|
||||
gEnableCloseLoop=1
|
||||
|
||||
#Data Inactivity Timeout when in powersave (in ms)
|
||||
gDataInactivityTimeout=200
|
||||
|
||||
# VHT Tx/Rx MCS values
|
||||
# Valid values are 0,1,2. If commented out, the default value is 0.
|
||||
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
||||
gVhtRxMCS=2
|
||||
gVhtTxMCS=2
|
||||
|
||||
# VHT Tx/Rx MCS values for 2x2
|
||||
# Valid values are 0,1,2. If commented out, the default value is 0.
|
||||
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
||||
gVhtRxMCS2x2=2
|
||||
gVhtTxMCS2x2=2
|
||||
|
||||
|
||||
# Valid chain mask values
|
||||
# 01 - enables chain0
|
||||
# 02 - enables chain1
|
||||
# 03 - enables both chain 0 and chain 1
|
||||
# if set to 0 or 1 then all vdevs comes up in 1x1 mode in that band.
|
||||
gChainMask_2g=3
|
||||
gChainMask_5g=3
|
||||
|
||||
# NSS cfg bit definition.
|
||||
# STA BIT[0:1]
|
||||
# SAP BIT[2:3]
|
||||
# P2P_GO BIT[4:5]
|
||||
# P2P_CLIENT BIT[6:7]
|
||||
# IBSS BIT[8:9]
|
||||
# TDLS BIT[10:11]
|
||||
# P2P_DEVICE BIT[12:13]
|
||||
# OCB BIT[14:15]
|
||||
# Valid values are 1 or 2 for each two bit configuration.
|
||||
# if 2-bit value is set to 1 then the corresponidng vdev comes up in 1x1 mode
|
||||
# in the band, if set to 2 then that vdev comes up in 2x2 mode in that band.
|
||||
gVdevTypeNss_2g=43690
|
||||
gVdevTypeNss_5g=43690
|
||||
|
||||
# Scan Timing Parameters
|
||||
# gPassiveMaxChannelTime=110
|
||||
# gPassiveMinChannelTime=60
|
||||
gActiveMaxChannelTime=80
|
||||
gActiveMinChannelTime=40
|
||||
|
||||
#If set to 0, MCC is not allowed.
|
||||
gEnableMCCMode=1
|
||||
|
||||
# MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band
|
||||
gWlanMccToSccSwitchMode = 0
|
||||
|
||||
# 1=enable STBC; 0=disable STBC
|
||||
gEnableRXSTBC=1
|
||||
|
||||
# 1=enable tx STBC; 0=disable
|
||||
gEnableTXSTBC=1
|
||||
|
||||
# 1=enable rx LDPC; 0=disable
|
||||
gEnableRXLDPC=1
|
||||
|
||||
# Enable Tx beamforming in VHT20MHz
|
||||
# Valid values are 0,1. If commented out, the default value is 0.
|
||||
# 0=disable, 1=enable
|
||||
gEnableTxBFin20MHz=1
|
||||
|
||||
# Enable Active mode offload
|
||||
gEnableActiveModeOffload=1
|
||||
|
||||
#Enable Scan Results Aging based on timer
|
||||
#Timer value is in seconds
|
||||
#If Set to 0 it will not enable the feature
|
||||
gScanAgingTime=0
|
||||
|
||||
#Enable Scan Results Aging based on number of scans
|
||||
gScanResultAgeCount=1
|
||||
|
||||
#Enable Power saving mechanism Based on Android Framework
|
||||
#If set to 0 Driver internally control the Power saving mechanism
|
||||
#If set to 1 Android Framwrok control the Power saving mechanism
|
||||
isAndroidPsEn=0
|
||||
|
||||
#Enable thermal mitigation
|
||||
gThermalMitigationEnable=0
|
||||
|
||||
gEnableFastRoamInConcurrency=1
|
||||
|
||||
#List of Country codes for which 11ac needs to be disabled
|
||||
#Each country code must be delimited by comma(,)
|
||||
gListOfNon11acCountryCode=RU,UA,ZA
|
||||
|
||||
#Maxium Channel time in msec
|
||||
gMaxMediumTime = 6000
|
||||
|
||||
# 802.11K support
|
||||
gRrmEnable=1
|
||||
gRrmOperChanMax=8
|
||||
gRrmNonOperChanMax=8
|
||||
gRrmRandIntvl=100
|
||||
|
||||
#Scan offload
|
||||
gEnableDirectedScanOffload=1
|
||||
|
||||
#FlexConnect Power Factor
|
||||
#Default is set to 0 (disable)
|
||||
gFlexConnectPowerFactor=0
|
||||
|
||||
#Disable split scan, the FW will take care of it
|
||||
gNumChanCombinedConc=60
|
||||
|
||||
#Enable Power Save offload
|
||||
gEnablePowerSaveOffload=2
|
||||
|
||||
#Enable firmware uart print
|
||||
gEnablefwprint=0
|
||||
|
||||
#Enable firmware log
|
||||
gEnablefwlog=1
|
||||
# Additional firmware log levels
|
||||
#gFwDebugLogLevel=4
|
||||
#gFwDebugModuleLoglevel=1,0,2,0,4,0,5,0,6,0,7,4,8,0,9,0,11,0,13,0,17,0,18,0,19,0,27,0,29,0,31,0,35,0,36,0,38,0
|
||||
|
||||
#IPA config
|
||||
gIPAConfig=0
|
||||
gIPADescSize=800
|
||||
gIPAPreFilterEnable=1
|
||||
gIPARMEnable=1
|
||||
gIPAIPv6Enable=1
|
||||
|
||||
#P2P Listen offload
|
||||
gEnableP2pListenOffload=1
|
||||
|
||||
# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets)
|
||||
gVhtMpduLen=2
|
||||
|
||||
# Maximum number of wow filters required
|
||||
#gMaxWoWFilters=22
|
||||
|
||||
# WOW Enable/Disable.
|
||||
# 0 - Disable both magic pattern match and pattern byte match.
|
||||
# 1 - Enable magic pattern match on all interfaces.
|
||||
# 2 - Enable pattern byte match on all interfaces.
|
||||
# 3 - Enable both magic patter and pattern byte match on all interfaces.
|
||||
# Default value of gEnableWoW is 3.
|
||||
# gEnableWoW=0
|
||||
|
||||
# Enable or Disable MCC Adaptive Scheduler at the FW
|
||||
# 1=Enable (default), 0=Disable
|
||||
gEnableMCCAdaptiveScheduler=1
|
||||
|
||||
#Enable or Disable p2p device address administered
|
||||
isP2pDeviceAddrAdministrated=1
|
||||
|
||||
# RX packet handling options
|
||||
# 0: no rx thread, no RPS, for MDM
|
||||
# 1: RX thread
|
||||
# 2: RPS
|
||||
rxhandle=1
|
||||
|
||||
# Set RPS CPU MAP as 0xe for the 4 RX queues
|
||||
# This allows use of CPU1-CPU3 but not CPU0 for 4 RX queues
|
||||
rpsRxQueueCpuMapList=c
|
||||
|
||||
# Set Thermal Power limit
|
||||
TxPower2g=10
|
||||
TxPower5g=10
|
||||
|
||||
# Remove Overlap channel restriction
|
||||
gEnableOverLapCh=0
|
||||
|
||||
#Enable VHT on 2.4Ghz
|
||||
gEnableVhtFor24GHzBand=1
|
||||
|
||||
#Enable or Disable 5G early beacon termination
|
||||
gEnable5gEBT=1
|
||||
|
||||
#Maximum number of offload peers supported
|
||||
# gMaxOffloadPeers=2
|
||||
|
||||
# controlling the following offload patterns
|
||||
# through ini parameter. Default value is 1
|
||||
# to disable set it to zero. ssdp = 0
|
||||
# Setup multicast pattern for mDNS 224.0.0.251,
|
||||
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
|
||||
ssdp = 0
|
||||
|
||||
#Enable Memory Deep Sleep
|
||||
gEnableMemDeepSleep=1
|
||||
|
||||
# Bus bandwidth threshold values in terms of number of packets
|
||||
gBusBandwidthHighThreshold=2000
|
||||
gBusBandwidthMediumThreshold=500
|
||||
gBusBandwidthLowThreshold=150
|
||||
|
||||
# IPA bandwidth voting
|
||||
gIPAHighBandwidthMbps=800
|
||||
gIPAMediumBandwidthMbps=400
|
||||
gIPALowBandwidthMbps=200
|
||||
|
||||
# Bus bandwidth compute timeout value in ms
|
||||
gBusBandwidthComputeInterval=100
|
||||
|
||||
# Regulatory Setting; 0=STRICT; 1=CUSTOM
|
||||
gRegulatoryChangeCountry=1
|
||||
# RA filtering rate limit param, the current value would not
|
||||
# help if the lifetime in RA is less than 3*60=3min. Then
|
||||
# we need to change it, though it is uncommon.
|
||||
# gRAFilterEnable=0
|
||||
gRArateLimitInterval=600
|
||||
|
||||
# Maximum number of concurrent connections
|
||||
gMaxConcurrentActiveSessions=2
|
||||
|
||||
# Disable/Enable GreenAP
|
||||
# 0 to disable, 1 to enable, default: 1
|
||||
gEnableGreenAp=1
|
||||
|
||||
# Radar PRI multiplier
|
||||
gDFSradarMappingPriMultiplier=4
|
||||
|
||||
gPNOScanSupport=1
|
||||
|
||||
# Enable/Disable RX full reorder offload
|
||||
gReorderOffloadSupported=1
|
||||
|
||||
# Enable/Disable LPASS support
|
||||
# 0 to disable, 1 to enable
|
||||
gEnableLpassSupport=1
|
||||
|
||||
# Whether userspace country code setting shld have priority
|
||||
gCountryCodePriority=1
|
||||
|
||||
# Enable(1)/Disable(0) SIFS burst
|
||||
gEnableSifsBurst=1
|
||||
|
||||
# Enable/Disable channel avoidance for SAP in SCC scenario
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
gSapSccChanAvoidance=0
|
||||
|
||||
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
|
||||
gIbssTxSpEndInactivityTime=10
|
||||
|
||||
# Enable/Disable Roaming Offload Support (a.k.a Key Management Offload)
|
||||
# 0 to disable, 1 to enable
|
||||
gRoamOffloadEnabled=0
|
||||
|
||||
# Enable support for TDLS
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
gEnableTDLSSupport=1
|
||||
|
||||
# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
|
||||
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
|
||||
# and RSSI) is met and then will initiate teardown when teardown criteria
|
||||
# (idle packet count and RSSI) is met.
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
gEnableTDLSImplicitTrigger=1
|
||||
|
||||
# Enable TDLS External Control. That is, user space application has to
|
||||
# first configure a peer MAC in wlan driver towards which TDLS is desired.
|
||||
# Device will establish TDLS only towards those configured peers whenever
|
||||
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
|
||||
# when teardown criteria (idle packet count and RSSI) is met. However,
|
||||
# device will accept TDLS connection if it is initiated from any other peer,
|
||||
# even if that peer is not configured.
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
# For TDLS External Control, Implicit Trigger must also be enabled.
|
||||
gTDLSExternalControl=1
|
||||
|
||||
# Enable support for TDLS off-channel operation
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
# TDLS off-channel operation will be invoked when there is only one
|
||||
# TDLS connection.
|
||||
gEnableTDLSOffChannel=1
|
||||
|
||||
IpaUcOffloadEnabled=1
|
||||
gIpaUcStaOffload=1
|
||||
|
||||
gEnableSelfRecovery=1
|
||||
|
||||
# Enable or Disable Random MAC (Spoofing)
|
||||
# 1=Enable, 0=Disable (default)
|
||||
gEnableMacAddrSpoof=0
|
||||
|
||||
# Enable Auto suspend feature
|
||||
# When this feature is enabled, it will shutdown the PCIe link
|
||||
# when inactivity is detected in STA disconnected mode.
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
gEnableBusAutoSuspend=0
|
||||
|
||||
# Enable Runtime PM Feature.
|
||||
# Enabling this feature will put target wow and shutdown pcie link
|
||||
# when inactivity is detected in WLAN Driver.
|
||||
# This feature is inactive when beaconing interfaces are active with
|
||||
# clients associated.
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
|
||||
gRuntimePM=1
|
||||
# When gRuntimePM is disabled gRuntimeAutoTime won't take effect.
|
||||
# The Time is in msec.
|
||||
# 100 is min, 10000 is max, 500 is default.
|
||||
|
||||
gRuntimePMDelay=500
|
||||
|
||||
# Enable to check FW hash if secure FW feature is enabled. It's for defconfig
|
||||
# builds only since it will be ignored in performance/release builds.
|
||||
gEnableFWHashCheck=1
|
||||
|
||||
# Enable FW to filter out broadcast packets and wakeup host during runtime PM.
|
||||
# As APPS is awake during runtime PM, if any application needs the broadcast
|
||||
# packets OEM's can enable this flag.
|
||||
# FW will filters the broadcast packets and wakeup host to deliver them during
|
||||
# runtime suspend.
|
||||
# This flag will take affect when Runtime PM is enabled
|
||||
gRuntimePmEnableBcastPattern=0
|
||||
|
||||
# Enable/disable 2x2
|
||||
# 0 - 1x1 (default)
|
||||
# 1 - 2x2
|
||||
gEnable2x2=1
|
||||
|
||||
# 3=enable both HT/VHT TX LDPC
|
||||
# 2=enable VHT TX LDPC
|
||||
# 1=enable HT TX LDPC
|
||||
# 0=disable
|
||||
gTxLdpcEnable=3
|
||||
|
||||
# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k)
|
||||
gVhtAmpduLenExponent=7
|
||||
|
||||
# SAP auto channel selection configuration
|
||||
# 0 = disable auto channel selection
|
||||
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
|
||||
gApAutoChannelSelection=1
|
||||
|
||||
#SOFTAP Channel Range selection
|
||||
gAPChannelSelectStartChannel=1
|
||||
|
||||
gAPChannelSelectEndChannel=11
|
||||
|
||||
|
||||
#SOFTAP Channel Range selection Operating band
|
||||
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
|
||||
gAPChannelSelectOperatingBand=0
|
||||
|
||||
# Enable or Disable Multi-user MIMO
|
||||
# 1=Enable (default), 0=Disable
|
||||
gEnableMuBformee=1
|
||||
|
||||
gSoftApMaxPeers=10
|
||||
END
|
||||
|
||||
# Note: Configuration parser would not read anything past the END marker
|
||||
|
||||
Loading…
Reference in a new issue