The following command sequence triggers an oops.
# mount /dev/sdb1 /mnt
# echo 1 > /sys/class/scsi_device/0\:0\:1\:0/device/delete
# umount /mnt
general protection fault: 0000 [#1] PREEMPT SMP
CPU 2
Modules linked in:
Pid: 791, comm: umount Not tainted 3.1.0-rc3-work+ #8 Bochs Bochs
RIP: 0010:[<ffffffff810d0879>] [<ffffffff810d0879>] __lock_acquire+0x389/0x1d60
...
Call Trace:
[<ffffffff810d2845>] lock_acquire+0x95/0x140
[<ffffffff81aed87b>] _raw_spin_lock+0x3b/0x50
[<ffffffff811573bc>] bdi_lock_two+0x5c/0x70
[<ffffffff811c2f6c>] bdev_inode_switch_bdi+0x4c/0xf0
[<ffffffff811c3fcb>] __blkdev_put+0x11b/0x1d0
[<ffffffff811c4010>] __blkdev_put+0x160/0x1d0
[<ffffffff811c40df>] blkdev_put+0x5f/0x190
[<ffffffff8118f18d>] kill_block_super+0x4d/0x80
[<ffffffff8118f4a5>] deactivate_locked_super+0x45/0x70
[<ffffffff8119003a>] deactivate_super+0x4a/0x70
[<ffffffff811ac4ad>] mntput_no_expire+0xed/0x130
[<ffffffff811acf2e>] sys_umount+0x7e/0x3a0
[<ffffffff81aeeeab>] system_call_fastpath+0x16/0x1b
This is because bdev holds on to disk but disk doesn't pin the
associated queue. If a SCSI device is removed while the device is
still open, the sdev puts the base reference to the queue on release.
When the bdev is finally released, the associated queue is already
gone along with the bdi and bdev_inode_switch_bdi() ends up
dereferencing already freed bdi.
Even if it were not for this bug, disk not holding onto the associated
queue is very unusual and error-prone.
Fix it by making add_disk() take an extra reference to its queue and
put it on disk_release() and ensuring that disk and its fops owner are
put in that order after all accesses to the disk and queue are
complete.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A kernel crash is observed when a mounted ext3/ext4 filesystem is
physically removed. The problem is that blk_cleanup_queue() frees up
some resources eg by calling elevator_exit(), which are not checked for
in normal operation. So we should rather move these calls to the
destructor function blk_release_queue() as at that point all remaining
references are gone. However, in doing so we have to ensure that any
externally supplied queue_lock is disconnected as the driver might free
up the lock after the call of blk_cleanup_queue(),
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The bug is we're not able to remove the device from blkio cgroup's
per-device control files if it gets unplugged.
To reproduce the bug:
# mount -t cgroup -o blkio xxx /cgroup
# cd /cgroup
# echo "8:0 1000" > blkio.throttle.read_bps_device
# unplug the device
# cat blkio.throttle.read_bps_device
8:0 1000
# echo "8:0 0" > blkio.throttle.read_bps_device
-bash: echo: write error: No such device
After patching, the device removal will succeed.
Thanks for the comments of Paul, Zefan, and Vivek.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Paul Menage <paul@paulmenage.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kerneldoc for blk_release_queue() is referring to blk_cleanup_queue().
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Thus spake Andrew Morton:
"And I have the usual maintainability whine. If someone comes up to
vmscan.c and sees it calling blk_start_plug(), how are they supposed to
work out why that call is there? They go look at the blk_start_plug()
definition and it is undocumented. I think we can do better than this?"
Adapted from the LWN article - http://lwn.net/Articles/438256/ by Jens
Axboe and from an earlier attempt by Shaohua Li to document blk-plug.
[akpm@linux-foundation.org: grammatical and spelling tweaks]
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move all the checks performed on a bio into a new helper, and call it as
soon as bio is submitted even if it is a re-submission from ->make_request.
We explicitly mark the new helper as beeing non-inlined as the stack
usage for printing the block device name in the failure case is quite
high and this a patch where we have to be extremely conservative about
stack usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In __blk_complete_request, we check both QUEUE_FLAG_SAME_COMP and req->cpu
to decide whether we should use req->cpu. Actually the user can also
select the complete cpu by either setting BIO_CPU_AFFINE or by calling
bio_set_completion_cpu. Current solution makes these 2 ways don't work
any more. So we'd better just check req->cpu.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Avoid the hacks need for request based device mappers currently by simply
exporting the symbol instead of trying to get it through the back door.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We have ELV_NAME_MAX defined to 16, and hence we should use it
instead of the magic nubmer 16 for elevator's name string.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch allows the user to set an "alias" of the disk via sysfs interface.
This patch only adds a new attribute "alias" in gendisk structure.
To show the alias instead of the device name in kernel messages,
we need to revise printk messages and use alias_name() in them.
Example:
(current) printk("disk name is %s\n", disk->disk_name);
(new) printk("disk name is %s\n", alias_name(disk));
Users can use alphabets, numbers, '-' and '_' in "alias" attribute. A disk can
have an "alias" which length is up to 255 bytes. This attribute is write-once.
Suggested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Suggested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Nao Nishijima <nao.nishijima.xt@hitachi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Cleaning up the code a little bit. attempt_plug_merge() traverses the plug
list anyway, we can do the request counting there, so stack size is reduced
a little bit.
The motivation here is I suspect if we should count the requests for each
queue (task could handle multiple disks in the meantime), but my test doesn't
show it's worthy doing. If somebody proves we should do it, below change
will make that more easier.
Signed-off-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Do blk_flush_plug_list() first and then add new request aDo blk_flush_plug_list() first and then add new request aDo blk_flush_plug_list() first and then add new request at the tail. New
request can't be merged to existing requests, but later new requests might
be merged with this new one. If blk_flush_plug_list() is done later, the
merge doesn't happen.
Believe it or not, this fixes a 10% regression running sysbench workload.
Signed-off-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit 5757a6d76c added the QUEUE_FLAG_SAME_FORCE flag, but fails to
clear that flag when the current state is '2' (SAME_COMP + SAME_FORCE)
and the new state is '1' (SAME_COMP).
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Eric Seppanen <eric@purestorage.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
There are cases where suppressing partition scan is useful - e.g. for
lo devices and pseudo SATA devices which advertise to be a disk but
get upset on partition scan (some port multiplier control devices show
such behavior).
This patch adds GENHD_FL_NO_PART_SCAN which suppresses partition scan
regardless of the number of possible partitions. disk_partitionable()
is renamed to disk_part_scan_enabled() as suppressing partition scan
doesn't imply the device can't be partitioned using
BLKPG_ADD/DEL_PARTITION calls from userland. show_partition() now
directly tests disk_max_parts() to maintain backward-compatibility.
-v2: Updated to make it clear that only partition scan is suppressed
not partitioning itself as suggested by Kay Sievers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Add a new REQ_PRIO to let requests preempt others in the cfq I/O schedule,
and lave REQ_META purely for marking requests as metadata in blktrace.
All existing callers of REQ_META except for XFS are updated to also
set REQ_PRIO for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
Revert "cfq: Remove special treatment for metadata rqs."
block: fix flush machinery for stacking drivers with differring flush flags
block: improve rq_affinity placement
blktrace: add FLUSH/FUA support
Move some REQ flags to the common bio/request area
allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
xen/blkback: Make description more obvious.
cfq-iosched: Add documentation about idling
block: Make rq_affinity = 1 work as expected
block: swim3: fix unterminated of_device_id table
block/genhd.c: remove useless cast in diskstats_show()
drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
bsg-lib: add module.h include
cfq-iosched: Reduce linked group count upon group destruction
blk-throttle: correctly determine sync bio
loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
loop: add management interface for on-demand device allocation
loop: replace linked list of allocated devices with an idr index
...
We have a kernel build regression since 3.1-rc1, which is about 10%
regression. The kernel source is in an ext3 filesystem.
Alex Shi bisect it to commit:
commit a07405b780
Author: Justin TerAvest <teravest@google.com>
Date: Sun Jul 10 22:09:19 2011 +0200
cfq: Remove special treatment for metadata rqs.
Apparently this is caused by lack metadata preemption, where ext3/ext4
do use READ_META. I didn't see a way to fix the issue, so suggest
reverting the patch.
This reverts commit a07405b780.
Reported-by: Alex Shi<alex.shi@intel.com>
Reported-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit ae1b153962, block: reimplement
FLUSH/FUA to support merge, introduced a performance regression when
running any sort of fsyncing workload using dm-multipath and certain
storage (in our case, an HP EVA). The test I ran was fs_mark, and it
dropped from ~800 files/sec on ext4 to ~100 files/sec. It turns out
that dm-multipath always advertised flush+fua support, and passed
commands on down the stack, where those flags used to get stripped off.
The above commit changed that behavior:
static inline struct request *__elv_next_request(struct request_queue *q)
{
struct request *rq;
while (1) {
- while (!list_empty(&q->queue_head)) {
+ if (!list_empty(&q->queue_head)) {
rq = list_entry_rq(q->queue_head.next);
- if (!(rq->cmd_flags & (REQ_FLUSH | REQ_FUA)) ||
- (rq->cmd_flags & REQ_FLUSH_SEQ))
- return rq;
- rq = blk_do_flush(q, rq);
- if (rq)
- return rq;
+ return rq;
}
Note that previously, a command would come in here, have
REQ_FLUSH|REQ_FUA set, and then get handed off to blk_do_flush:
struct request *blk_do_flush(struct request_queue *q, struct request *rq)
{
unsigned int fflags = q->flush_flags; /* may change, cache it */
bool has_flush = fflags & REQ_FLUSH, has_fua = fflags & REQ_FUA;
bool do_preflush = has_flush && (rq->cmd_flags & REQ_FLUSH);
bool do_postflush = has_flush && !has_fua && (rq->cmd_flags &
REQ_FUA);
unsigned skip = 0;
...
if (blk_rq_sectors(rq) && !do_preflush && !do_postflush) {
rq->cmd_flags &= ~REQ_FLUSH;
if (!has_fua)
rq->cmd_flags &= ~REQ_FUA;
return rq;
}
So, the flush machinery was bypassed in such cases (q->flush_flags == 0
&& rq->cmd_flags & (REQ_FLUSH|REQ_FUA)).
Now, however, we don't get into the flush machinery at all. Instead,
__elv_next_request just hands a request with flush and fua bits set to
the scsi_request_fn, even if the underlying request_queue does not
support flush or fua.
The agreed upon approach is to fix the flush machinery to allow
stacking. While this isn't used in practice (since there is only one
request-based dm target, and that target will now reflect the flush
flags of the underlying device), it does future-proof the solution, and
make it function as designed.
In order to make this work, I had to add a field to the struct request,
inside the flush structure (to store the original req->end_io). Shaohua
had suggested overloading the union with rb_node and completion_data,
but the completion data is used by device mapper and can also be used by
other drivers. So, I didn't see a way around the additional field.
I tested this patch on an HP EVA with both ext4 and xfs, and it recovers
the lost performance. Comments and other testers, as always, are
appreciated.
Cheers,
Jeff
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch reverts commit 35ae66e0a09ab70ed(block: Make rq_affinity = 1
work as expected). The purpose is to avoid an unnecessary IPI.
Let's take an example. My test box has cpu 0-7, one socket. Say request is
added from CPU 1, blk_complete_request() occurs at CPU 7. Without the reverted
patch, softirq will be done at CPU 7. With it, an IPI will be directed to CPU
0, and softirq will be done at CPU 0. In this case, doing softirq at CPU 0 and
CPU 7 have no difference from cache sharing point view and we can avoid an
ipi if doing it in CPU 7.
An immediate concern is this is just like QUEUE_FLAG_SAME_FORCE, but actually
not. blk_complete_request() is running in interrupt handler, and currently
I/O controller doesn't support multiple interrupts (I checked several LSI
cards and AHCI), so only one CPU can run blk_complete_request(). This is
still quite different as QUEUE_FLAG_SAME_FORCE.
Since only one CPU runs softirq, the only difference with below patch is
softirq not always runs at the first CPU of a group.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
blk_insert_flush has the following check:
/*
* If there's data but flush is not necessary, the request can be
* processed directly without going through flush machinery. Queue
* for normal execution.
*/
if ((policy & REQ_FSEQ_DATA) &&
!(policy & (REQ_FSEQ_PREFLUSH | REQ_FSEQ_POSTFLUSH))) {
list_add_tail(&rq->queuelist, &q->queue_head);
return;
}
However, blk_flush_policy will not return with policy set to only
REQ_FSEQ_DATA:
static unsigned int blk_flush_policy(unsigned int fflags, struct request *rq)
{
unsigned int policy = 0;
if (fflags & REQ_FLUSH) {
if (rq->cmd_flags & REQ_FLUSH)
policy |= REQ_FSEQ_PREFLUSH;
if (blk_rq_sectors(rq))
policy |= REQ_FSEQ_DATA;
if (!(fflags & REQ_FUA) && (rq->cmd_flags & REQ_FUA))
policy |= REQ_FSEQ_POSTFLUSH;
}
return policy;
}
Notice that REQ_FSEQ_DATA is only set if REQ_FLUSH is set. Fix this
mismatch by moving the setting of REQ_FSEQ_DATA outside of the REQ_FLUSH
check.
Tejun notes:
Hmmm... yes, this can become a correctness issue if (and only if)
blk_queue_flush() is called to change q->flush_flags while requests
are in-flight; otherwise, requests wouldn't reach the function at all.
Also, I think it would be a generally good idea to always set
FSEQ_DATA if the request has data.
Cheers,
Jeff
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit 5757a6d76c introduced a new rq_affinity = 2 so as to make
the request completed in the __make_request cpu. But it makes the
old rq_affinity = 1 not work any more. The root cause is that
if the 'cpu' and 'req->cpu' is in the same group and cpu != req->cpu,
ccpu will be the same as group_cpu, so the completion will be
excuted in the 'cpu' not 'group_cpu'.
This patch fix problem by simpling removing group_cpu and the codes
are more explicit now. If ccpu == cpu, we complete in cpu, otherwise
we raise_blk_irq to ccpu.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Reviewed-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
init_fault_attr_dentries() is used to export fault_attr via debugfs.
But it can only export it in debugfs root directory.
Per Forlin is working on mmc_fail_request which adds support to inject
data errors after a completed host transfer in MMC subsystem.
The fault_attr for mmc_fail_request should be defined per mmc host and
export it in debugfs directory per mmc host like
/sys/kernel/debug/mmc0/mmc_fail_request.
init_fault_attr_dentries() doesn't help for mmc_fail_request. So this
introduces fault_create_debugfs_attr() which is able to create a
directory in the arbitrary directory and replace
init_fault_attr_dentries().
[akpm@linux-foundation.org: extraneous semicolon, per Randy]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Per Forlin <per.forlin@linaro.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the (unsigned long long) cast in diskstats_show() and adjusts the
seq_printf() format string to 'unsigned long'
diskstats_show() uses part_stat_read() to get the stats, which either
accesses the specified field in the struct disk_stats directly (non SMP)
or sums up the per CPU values in a variable of the same type as the field,
so in any case the result will have the same type and range as the
specified field which for all disk_stats entries is unsigned long
Also, for unsigned long ranges the output of %lu should be identical to
the one of %llu, so no change in the actual proc entry contents.
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Due to conflicts with the moduleh tree in linux-next, we
run into an include file mess. We really need export.h
in that tree, but if we add module.h locally then the
issue is easier to resolve.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
FQ keeps track of number of groups which are linked on blkcg->blkg_list.
This is useful to avoid races between queue exit and cgroup exit code
paths. So if at the request queue exit time linked group count is not
zero, that means there are some group out there which is yet to be
deleted under rcu read period and queue exit code should wait for
on rcu period.
In my previous patch I forgot to decrease the number of group count.
So in current form, we nr_blkcg_linked_grps is always non-zero and
we will always wait one rcu period (if BLK_CGROUP=y). The side effect
of this is that it can increase boot time. I am surprised, nobody
complained so far.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
read request is always sync. Using rw_is_sync() to determine
if a bio is sync.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This moves the FC classes bsg code to the block layer and
makes it a lib so that other classes like iscsi and SAS can use it.
It is helpful because working with the request queue, bios,
creating scatterlists, etc are a pain that the LLD does not
have to worry about with normal IOs and should not have to
worry about for bsg requests.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This changes should_fail_request() to more usable wrapper function of
should_fail(). It can avoid putting #ifdef CONFIG_FAIL_MAKE_REQUEST in
the middle of a function.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit 5757a6d7 introduced an unsafe calling of
smp_processor_id(), with preempt debuggin turned on we spew a lot of:
BUG: using smp_processor_id() in preemptible [00000000] code: kjournald/514
caller is __make_request+0x1b8/0x308
[<c0019f44>] (unwind_backtrace+0x0/0xe8) from [<c024b4cc>] (debug_smp_processor_id+0xbc/0xf0)
[<c024b4cc>] (debug_smp_processor_id+0xbc/0xf0) from [<c0223d14>] (__make_request+0x1b8/0x308)
[<c0223d14>] (__make_request+0x1b8/0x308) from [<c02215ac>] (generic_make_request+0x4dc/0x558)
[<c02215ac>] (generic_make_request+0x4dc/0x558) from [<c022173c>] (submit_bio+0x114/0x138)
[<c022173c>] (submit_bio+0x114/0x138) from [<c011f504>] (submit_bh+0x148/0x16c)
[<c011f504>] (submit_bh+0x148/0x16c) from [<c0121ed8>] (__sync_dirty_buffer+0x88/0xd8)
[<c0121ed8>] (__sync_dirty_buffer+0x88/0xd8) from [<c01aff78>] (journal_commit_transaction+0x1198/0x1688)
[<c01aff78>] (journal_commit_transaction+0x1198/0x1688) from [<c01b4034>] (kjournald+0xb4/0x224)
[<c01b4034>] (kjournald+0xb4/0x224) from [<c0069ea0>] (kthread+0x8c/0x94)
[<c0069ea0>] (kthread+0x8c/0x94) from [<c00137f8>] (kernel_thread_exit+0x0/0x8)
Fix this by just using raw_smp_processor_id(), it's just a hint
after all. There's no pinning of the CPU or accessing per-cpu
structures involved.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-3.1/drivers' of git://git.kernel.dk/linux-block:
cciss: do not attempt to read from a write-only register
xen/blkback: Add module alias for autoloading
xen/blkback: Don't let in-flight requests defer pending ones.
bsg: fix address space warning from sparse
bsg: remove unnecessary conditional expressions
bsg: fix bsg_poll() to return POLLOUT properly
* 'for-3.1/core' of git://git.kernel.dk/linux-block: (24 commits)
block: strict rq_affinity
backing-dev: use synchronize_rcu_expedited instead of synchronize_rcu
block: fix patch import error in max_discard_sectors check
block: reorder request_queue to remove 64 bit alignment padding
CFQ: add think time check for group
CFQ: add think time check for service tree
CFQ: move think time check variables to a separate struct
fixlet: Remove fs_excl from struct task.
cfq: Remove special treatment for metadata rqs.
block: document blk_plug list access
block: avoid building too big plug list
compat_ioctl: fix make headers_check regression
block: eliminate potential for infinite loop in blkdev_issue_discard
compat_ioctl: fix warning caused by qemu
block: flush MEDIA_CHANGE from drivers on close(2)
blk-throttle: Make total_nr_queued unsigned
block: Add __attribute__((format(printf...) and fix fallout
fs/partitions/check.c: make local symbols static
block:remove some spare spaces in genhd.c
block:fix the comment error in blkdev.h
...
Some systems benefit from completions always being steered to the strict
requester cpu rather than the looser "per-socket" steering that
blk_cpu_to_group() attempts by default. This is because the first
CPU in the group mask ends up being completely overloaded with work,
while the others (including the original submitter) has power left
to spare.
Allow the strict mode to be set by writing '2' to the sysfs control
file. This is identical to the scheme used for the nomerges file,
where '2' is a more aggressive setting than just being turned on.
echo 2 > /sys/block/<bdev>/queue/rq_affinity
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Roland Dreier <roland@purestorage.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
A '!' snuck in before the unlikely, rendering it useless.
Reported-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (77 commits)
[SCSI] fix crash in scsi_dispatch_cmd()
[SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise
[SCSI] bnx2i: Fixed kernel panic due to illegal usage of sc->request->cpu
[SCSI] bfa: Update the driver version to 3.0.2.1
[SCSI] bfa: Driver and BSG enhancements.
[SCSI] bfa: Added support to query PHY.
[SCSI] bfa: Added HBA diagnostics support.
[SCSI] bfa: Added support for flash configuration
[SCSI] bfa: Added support to obtain SFP info.
[SCSI] bfa: Added support for CEE info and stats query.
[SCSI] bfa: Extend BSG interface.
[SCSI] bfa: FCS bug fixes.
[SCSI] bfa: DMA memory allocation enhancement.
[SCSI] bfa: Brocade-1860 Fabric Adapter vHBA support.
[SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
[SCSI] bfa: Added Fabric Assigned Address(FAA) support
[SCSI] bfa: IOC bug fixes.
[SCSI] bfa: Enable ASIC block configuration and query.
[SCSI] bnx2i: Updated copyright and bump version
[SCSI] bnx2i: Modified to skip CNIC registration if iSCSI is not supported
...
Fix up some trivial conflicts in:
- drivers/scsi/bnx2fc/{bnx2fc.h,bnx2fc_fcoe.c}:
Crazy broadcom version number conflicts
- drivers/target/tcm_fc/tfc_cmd.c
Just trivial cleanups done on adjacent lines
USB surprise removal of sr is triggering an oops in
scsi_dispatch_command(). What seems to be happening is that USB is
hanging on to a queue reference until the last close of the upper
device, so the crash is caused by surprise remove of a mounted CD
followed by attempted unmount.
The problem is that USB doesn't issue its final commands as part of
the SCSI teardown path, but on last close when the block queue is long
gone. The long term fix is probably to make sr do the teardown in the
same way as sd (so remove all the lower bits on ejection, but keep the
upper disk alive until last close of user space). However, the
current oops can be simply fixed by not allowing any commands to be
sent to a dead queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The rcu callback disk_free_ptbl_rcu_cb() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(disk_free_ptbl_rcu_cb).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Currently when the last queue of a group has no request, we don't expire
the queue to hope request from the group comes soon, so the group doesn't
miss its share. But if the think time is big, the assumption isn't correct
and we just waste bandwidth. In such case, we don't do idle.
[global]
runtime=30
direct=1
[test1]
cgroup=test1
cgroup_weight=1000
rw=randread
ioengine=libaio
size=500m
runtime=30
directory=/mnt
filename=file1
thinktime=9000
[test2]
cgroup=test2
cgroup_weight=1000
rw=randread
ioengine=libaio
size=500m
runtime=30
directory=/mnt
filename=file2
patched base
test1 64k 39k
test2 548k 540k
total 604k 578k
group1 gets much better throughput because it waits less time.
To check if the patch changes behavior of queue without think time. I also
tried to give test1 2ms think time or no think time. The test result is stable.
The thoughput doesn't change with/without the patch.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently when the last queue of a service tree has no request, we don't
expire the queue to hope request from the service tree comes soon, so the
service tree doesn't miss its share. But if the think time is big, the
assumption isn't correct and we just waste bandwidth. In such case, we
don't do idle.
[global]
runtime=10
direct=1
[test1]
rw=randread
ioengine=libaio
size=500m
directory=/mnt
filename=file1
thinktime=9000
[test2]
rw=read
ioengine=libaio
size=1G
directory=/mnt
filename=file2
patched base
test1 41k/s 33k/s
test2 15868k/s 15789k/s
total 15902k/s 15817k/s
A slightly better
To check if the patch changes behavior of queue without think time. I also
tried to give test1 2ms think time or no think time. The test has variation
even without the patch, but the average throughput doesn't change with/without
the patch.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Move the variables to do think time check to a sepatate struct. This is
to prepare adding think time check for service tree and group. No
functional change.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
fs_excl is a poor man's priority inheritance for filesystems to hint to
the block layer that an operation is important. It was never clearly
specified, not widely adopted, and will not prevent starvation in many
cases (like across cgroups).
fs_excl was introduced with the time sliced CFQ IO scheduler, to
indicate when a process held FS exclusive resources and thus needed
a boost.
It doesn't cover all file systems, and it was never fully complete.
Lets kill it.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
There is no consistency among filesystems from what bios (or requests)
are marked as being metadata. It's interesting to expose this in traces,
but we shouldn't schedule the requests differently based on whether or
not they're marked as being metadata.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When I test fio script with big I/O depth, I found the total throughput drops
compared to some relative small I/O depth. The reason is the thread accumulates
big requests in its plug list and causes some delays (surely this depends
on CPU speed).
I thought we'd better have a threshold for requests. When a threshold reaches,
this means there is no request merge and queue lock contention isn't severe
when pushing per-task requests to queue, so the main advantages of blk plug
don't exist. We can force a plug list flush in this case.
With this, my test throughput actually increases and almost equals to small
I/O depth. Another side effect is irq off time decreases in blk_flush_plug_list()
for big I/O depth.
The BLK_MAX_REQUEST_COUNT is choosen arbitarily, but 16 is efficiently to
reduce lock contention to me. But I'm open here, 32 is ok in my test too.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Due to the recently identified overflow in read_capacity_16() it was
possible for max_discard_sectors to be zero but still have discards
enabled on the associated device's queue.
Eliminate the possibility for blkdev_issue_discard to infinitely loop.
Interestingly this issue wasn't identified until a device, whose
discard_granularity was 0 due to read_capacity_16 overflow, was consumed
by blk_stack_limits() to construct limits for a higher-level DM
multipath device. The multipath device's resulting limits never had the
discard limits stacked because blk_stack_limits() will only do so if
the bottom device's discard_granularity != 0. This resulted in the
multipath device's limits.max_discard_sectors being 0.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
On Linux x86_64 host with 32bit userspace, running
qemu or even just "qemu-img create -f qcow2 some.img 1G"
causes a kernel warning:
ioctl32(qemu-img:5296): Unknown cmd fd(3) cmd(00005326){t:'S';sz:0} arg(7fffffff) on some.img
ioctl32(qemu-img:5296): Unknown cmd fd(3) cmd(801c0204){t:02;sz:28} arg(fff77350) on some.img
ioctl 00005326 is CDROM_DRIVE_STATUS,
ioctl 801c0204 is FDGETPRM.
The warning appears because the Linux compat-ioctl handler for these
ioctls only applies to block devices, while qemu also uses the ioctls on
plain files.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently, only open(2) is defined as the 'clearing' point. It has
two roles - first, it's an acknowledgement from userland indicating
that the event has been received and kernel can clear pending states
and proceed to generate more events. Secondly, it's passed on to
device drivers as a hint indicating that a synchronization point has
been reached and it might want to take a deeper look at the device.
The latter currently is only used by sr which uses two different
mechanisms - GET_EVENT_MEDIA_STATUS_NOTIFICATION and TEST_UNIT_READY
to discover events, where the former is lighter weight and safe to be
used repeatedly but may not provide full coverage. Among other
things, GET_EVENT can't detect media removal while TUR can.
This patch makes close(2) - blkdev_put() - indicate clearing hint for
MEDIA_CHANGE to drivers. disk_check_events() is renamed to
disk_flush_events() and updated to take @mask for events to flush
which is or'd to ev->clearing and will be passed to the driver on the
next ->check_events() invocation.
This change makes sr generate MEDIA_CHANGE when media is ejected from
userland - e.g. with eject(1).
Note: Given the current usage, it seems @clearing hint is needlessly
complex. disk_clear_events() can simply clear all events and the hint
can be boolean @flush.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
ioc->ioc_data is rcu protectd, so uses correct API to access it.
This doesn't change any behavior, but just make code consistent.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: stable@kernel.org # after ab4bd22d
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
I got a rcu warnning at boot. the ioc->ioc_data is rcu_deferenced, but
doesn't hold rcu_read_lock.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: stable@kernel.org # after ab4bd22d
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Second condition in OR always implies first condition is false
thus bytes_read in the second is not needed. The same goes to
bytes_written.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
POLLOUT should be returned only if bd->queued_cmds < bd->max_queue
so that bsg_alloc_command() can proceed.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The total of two unsigned values should also be unsigned.
Update throtl_log output to unsigned.
Update total_nr_queued test to non-zero to be the
same as the other total_nr_queued tests.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Use the compiler to verify format strings and arguments.
Fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Use the compiler to verify format strings and arguments.
Fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
disk_block_events() should guarantee that the event work is not in
flight on return and once blocked it shouldn't issue further
cancellations.
Because there was no synchronization between the first blocker doing
cancel_delayed_work_sync() and the following blockers, the following
blockers could finish before cancellation was complete, which broke
both guarantees - event work could be in flight and cancellation could
happen after return.
This bug triggered WARN_ON_ONCE() in disk_clear_events() reported in
bug#34662.
https://bugzilla.kernel.org/show_bug.cgi?id=34662
Fix it by adding an outer mutex which protects both block count
manipulation and work cancellation.
-v2: Use outer mutex instead of bit waitqueue per Linus.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
After the previous update to disk_check_events(), nobody is using
non-syncing __disk_block_events(). Remove @sync and, as this makes
__disk_block_events() virtually identical to disk_block_events(),
remove the underscore prefixed version.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch is part of fix for triggering of WARN_ON_ONCE() in
disk_clear_events() reported in bug#34662.
https://bugzilla.kernel.org/show_bug.cgi?id=34662
disk_clear_events() blocks events, schedules and flushes the event
work. It expects the work to have started execution on schedule and
finished on return from flush. WARN_ON_ONCE() triggers if the event
work hasn't executed as expected. This problem happens because
__disk_block_events() fails to guarantee that the event work item is
not in flight on return from the function in race-free manner. The
problem is two-fold and this patch addresses one of them.
When __disk_block_events() is called with @sync == %false, it bumps
event block count, calls cancel_delayed_work() and return. This makes
it impossible to guarantee that event polling is not in flight on
return from syncing __disk_block_events() - if the first blocker was
non-syncing, polling could still be in progress and later syncing ones
would assume that the first blocker already canceled it.
Making __disk_block_events() cancel_sync regardless of block count
isn't feasible either as it may race with forced event checking in
disk_clear_events().
As disk_check_events() is the only user of non-syncing
__disk_block_events(), updating it to directly cancel and schedule
event work is the easiest way to solve the issue.
Note that there's another bug in __disk_block_events() and this patch
doesn't fix the issue completely. Later patch will fix the other bug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If we rename the return of alloc_io_context() and get_io_context() from
"ret" to "ioc" the code get's (a bit) more readable and (a lot) more
grepable.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Since we are modifying this RCU pointer, we need to hold
the lock protecting it around it.
This fixes a potential reuse and double free of a cfq
io_context structure. The bug has been in CFQ for a long
time, it hit very few people but those it did hit seemed
to see it a lot.
Tracked in RH bugzilla here:
https://bugzilla.redhat.com/show_bug.cgi?id=577968
Credit goes to Paul Bolle for figuring out that the issue
was around the one-hit ioc->ioc_data cache. Thanks to his
hard work the issue is now fixed.
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Since we are modifying this RCU pointer, we need to hold
the lock protecting it around it.
This fixes a potential reuse and double free of a cfq
io_context structure. The bug has been in CFQ for a long
time, it hit very few people but those it did hit seemed
to see it a lot.
Tracked in RH bugzilla here:
https://bugzilla.redhat.com/show_bug.cgi?id=577968
Credit goes to Paul Bolle for figuring out that the issue
was around the one-hit ioc->ioc_data cache. Thanks to his
hard work the issue is now fixed.
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Hi, Jens,
If you recall, I posted an RFC patch for this back in July of last year:
http://lkml.org/lkml/2010/7/13/279
The basic problem is that a process can issue a never-ending stream of
async direct I/Os to the same sector on a device, thus starving out
other I/O in the system (due to the way the alias handling works in both
cfq and deadline). The solution I proposed back then was to start
dispatching from the fifo after a certain number of aliases had been
dispatched. Vivek asked why we had to treat aliases differently at all,
and I never had a good answer. So, I put together a simple patch which
allows aliases to be added to the rb tree (it adds them to the right,
though that doesn't matter as the order isn't guaranteed anyway). I
think this is the preferred solution, as it doesn't break up time slices
in CFQ or batches in deadline. I've tested it, and it does solve the
starvation issue. Let me know what you think.
Cheers,
Jeff
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
list_entry() and hlist_entry() are both simply aliases for
container_of(), but since io_context.cic_list.first is an hlist_node one
should at least use the correct alias.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
queue_fail can only be reached if cic is NULL, so its check for cic must
be bogus.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Add cgroup subsystem callbacks for per-thread attachment in atomic contexts
Add can_attach_task(), pre_attach(), and attach_task() as new callbacks
for cgroups's subsystem interface. Unlike can_attach and attach, these
are for per-thread operations, to be called potentially many times when
attaching an entire threadgroup.
Also, the old "bool threadgroup" interface is removed, as replaced by
this. All subsystems are modified for the new interface - of note is
cpuset, which requires from/to nodemasks for attach to be globally scoped
(though per-cpuset would work too) to persist from its pre_attach to
attach_task and attach.
This is a pre-patch for cgroup-procs-writable.patch.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
9fd097b149 (block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe
drivers) removed DISK_EVENT_MEDIA_CHANGE from legacy/fringe block
drivers which have inadequate ->check_events(). Combined with earlier
change 7c88a168da (block: don't propagate unlisted DISK_EVENTs to
userland), this enables using ->check_events() for internal processing
while avoiding enabling in-kernel block event polling which can lead
to infinite event loop.
Unfortunately, this made many drivers including floppy without any bit
set in disk->events and ->async_events in which case disk_add_events()
simply skipped allocation of disk->ev, which disables whole event
handling. As ->check_events() is still used during open processing
for revalidation, this can lead to open failure.
This patch always allocates disk->ev if ->check_events is implemented.
In the long term, it would make sense to simply include the event
structure inline into genhd as it's now used by virtually all block
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Reported-by: Alex Villacis Lasso <avillaci@ceibo.fiec.espol.edu.ec>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When struct cfq_data allocation fails, cic_index need to be freed.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The 'group_changed' variable is initialized to 0 and never changed, so
checking the variable is meaningless.
It is a leftover from 0bbfeb8320 ("cfq-iosched: Always provide group
iosolation."). Let's get rid of it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Reduce the number of bit operations in cfq_choose_req() on average
(and worst) cases.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Simplify the calculation in cfq_prio_to_maxrq(), plus replace CFQ_PRIO_LISTS to
IOPRIO_BE_NR since they are the same and IOPRIO_BE_NR looks more reasonable in
this context IMHO.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If we don't explicitly initialize it to zero, CFQ might think that
cgroup of ioc has changed and it generates lots of unnecessary calls
to call_for_each_cic(changed_cgroup). Fix it.
cfq_get_io_context()
cfq_ioc_set_cgroup()
call_for_each_cic(ioc, changed_cgroup)
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit 73c1010119 ("block: initial patch for on-stack per-task plugging")
removed calls to elv_bio_merged() when @bio merged with @req. Re-add them.
This in turn will update merged stats in associated group. That
should be safe as long as request has got reference to the blkio_group.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Divyesh Shah <dpshah@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Make BLKIO_STAT_MERGED per cpu hence gettring rid of need of taking
blkg->stats_lock.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We allocated per cpu stats struct for root group but did not free it.
Fix it.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We don't need them anymore, so kill:
- REQ_ON_PLUG checks in various places
- !rq_mergeable() check in plug merging
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently we take a queue lock on each bio to check if there are any
throttling rules associated with the group and also update the stats.
Now access the group under rcu and update the stats without taking
the queue lock. Queue lock is taken only if there are throttling rules
associated with the group.
So the common case of root group when there are no rules, save
unnecessary pounding of request queue lock.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Now dispatch stats update is lock free. But reset of these stats still
takes blkg->stats_lock and is dependent on that. As stats are per cpu,
we should be able to just reset the stats on each cpu without any locks.
(Atleast for 64bit arch).
On 32bit arch there is a small race where 64bit updates are not atomic.
The result of this race can be that in the presence of other writers,
one might not get 0 value after reset of a stat and might see something
intermediate
One can write more complicated code to cover this race like sending IPI
to other cpus to reset stats and for offline cpus, reset these directly.
Right not I am not taking that path because reset_update is more of a
debug feature and it can happen only on 32bit arch and possibility of
it happening is small. Will fix it if it becomes a real problem. For
the time being going for code simplicity.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Some of the stats are 64bit and updation will be non atomic on 32bit
architecture. Use sequence counters on 32bit arch to make reading
of stats safe.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently we take blkg_stat lock for even updating the stats. So even if
a group has no throttling rules (common case for root group), we end
up taking blkg_lock, for updating the stats.
Make dispatch stats per cpu so that these can be updated without taking
blkg lock.
If cpu goes offline, these stats simply disappear. No protection has
been provided for that yet. Do we really need anything for that?
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Soon we will allow accessing a throtl_grp under rcu_read_lock(). Hence
start freeing up throtl_grp after one rcu grace period.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Use same helper function for root group as we use with dynamically
allocated groups to add it to various lists.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
A helper function for the code which is used at 2-3 places. Makes reading
code little easier.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently, we allocate root throtl_grp statically. But as we will be
introducing per cpu stat pointers and that will be allocated
dynamically even for root group, we might as well make whole root
throtl_grp allocation dynamic and treat it in same manner as other
groups.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently, all the cfq_group or throtl_group allocations happen while
we are holding ->queue_lock and sleeping is not allowed.
Soon, we will move to per cpu stats and also need to allocate the
per group stats. As one can not call alloc_percpu() from atomic
context as it can sleep, we need to drop ->queue_lock, allocate the
group, retake the lock and continue processing.
In throttling code, I check the queue DEAD flag again to make sure
that driver did not call blk_cleanup_queue() in the mean time.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
blkg->key = cfqd is an rcu protected pointer and hence we used to do
call_rcu(cfqd->rcu_head) to free up cfqd after one rcu grace period.
The problem here is that even though cfqd is around, there are no
gurantees that associated request queue (td->queue) or q->queue_lock
is still around. A driver might have called blk_cleanup_queue() and
release the lock.
It might happen that after freeing up the lock we call
blkg->key->queue->queue_ock and crash. This is possible in following
path.
blkiocg_destroy()
blkio_unlink_group_fn()
cfq_unlink_blkio_group()
Hence, wait for an rcu peirod if there are groups which have not
been unlinked from blkcg->blkg_list. That way, if there are any groups
which are taking cfq_unlink_blkio_group() path, can safely take queue
lock.
This is how we have taken care of race in throttling logic also.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Nobody seems to be using cfq_find_alloc_cfqg() function parameter "create".
Get rid of that.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cgroup unaccounted_time file is created only if CONFIG_DEBUG_BLK_CGROUP=y.
there are some fields which are out side this config option. Fix that.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Group initialization code seems to be at two places. root group
initialization in blk_throtl_init() and dynamically allocated group
in throtl_find_alloc_tg(). Create a common function and use at both
the places.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Since for-2.6.40/core was forked off the 2.6.39 devel tree, we've
had churn in the core area that makes it difficult to handle
patches for eg cfq or blk-throttle. Instead of requiring that they
be based in older versions with bugs that have been fixed later
in the rc cycle, merge in 2.6.39 final.
Also fixes up conflicts in the below files.
Conflicts:
drivers/block/paride/pcd.c
drivers/cdrom/viocd.c
drivers/ide/ide-cd.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
blk_cleanup_queue() calls elevator_exit() and after this, we can't
touch the elevator without oopsing. __elv_next_request() must check
for this state because in the refcounted queue model, we can still
call it after blk_cleanup_queue() has been called.
This was reported as causing an oops attributable to scsi.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Let's check a scenario:
1. blk_delay_queue(q, SCSI_QUEUE_DELAY);
2. blk_run_queue_async();
the second one will became a noop, because q->delay_work already has
WORK_STRUCT_PENDING_BIT set, so the delayed work will still run after
SCSI_QUEUE_DELAY. But blk_run_queue_async actually hopes the delayed
work runs immediately.
Fix this by doing a cancel on potentially pending delayed work
before queuing an immediate run of the workqueue.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In some cases we would end up stacking discard_zeroes_data incorrectly.
Fix this by enabling the feature by default for stacking drivers and
clearing it for low-level drivers. Incorporating a device that does not
support dzd will then cause the feature to be disabled in the stacking
driver.
Also ensure that the maximum discard value does not overflow when
exported in sysfs and return 0 in the alignment and dzd fields for
devices that don't support discard.
Reported-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currentlly we first map the task to cgroup and then cgroup to
blkio_cgroup. There is a more direct way to get to blkio_cgroup
from task using task_subsys_state(). Use that.
The real reason for the fix is that it also avoids a race in generic
cgroup code. During remount/umount rebind_subsystems() is called and
it can do following with and rcu protection.
cgrp->subsys[i] = NULL;
That means if somebody got hold of cgroup under rcu and then it tried
to do cgroup->subsys[] to get to blkio_cgroup, it would get NULL which
is wrong. I was running into this race condition with ltp running on a
upstream derived kernel and that lead to crash.
So ideally we should also fix cgroup generic code to wait for rcu
grace period before setting pointer to NULL. Li Zefan is not very keen
on introducing synchronize_wait() as he thinks it will slow
down moun/remount/umount operations.
So for the time being atleast fix the kernel crash by taking a more
direct route to blkio_cgroup.
One tester had reported a crash while running LTP on a derived kernel
and with this fix crash is no more seen while the test has been
running for over 6 days.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently we return -EOPNOTSUPP in blkdev_issue_discard() if any of the
bio fails due to underlying device not supporting discard request.
However, if the device is for example dm device composed of devices
which some of them support discard and some of them does not, it is ok
for some bios to fail with EOPNOTSUPP, but it does not mean that discard
is not supported at all.
This commit removes the check for bios failed with EOPNOTSUPP and change
blkdev_issue_discard() to return operation not supported if and only if
the device does not actually supports it, not just part of the device as
some bios might indicate.
This change also fixes problem with BLKDISCARD ioctl() which now works
correctly on such dm devices.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
CC: Jens Axboe <jaxboe@fusionio.com>
CC: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In blkdev_issue_zeroout() we are submitting regular WRITE bios, so we do
not need to check for -EOPNOTSUPP specifically in case of error. Also
there is no need to have label submit: because there is no way to jump
out from the while cycle without an error and we really want to exit,
rather than try again. And also remove the check for (sz == 0) since at
that point sz can never be zero.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
CC: Dmitry Monakhov <dmonakhov@openvz.org>
CC: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently we are waiting for every submitted REQ_DISCARD bio separately,
but it can have unwanted consequences of repeatedly flushing the queue,
so we rather submit bios in batches and wait for the entire batch, hence
narrowing the window of other ios going in.
Use bio_batch_end_io() and struct bio_batch for that purpose, the same
is used by blkdev_issue_zeroout(). Also change bio_batch_end_io() so we
always set !BIO_UPTODATE in the case of error and remove the check for
bb, since we are the only user of this function and we always set this.
Remove bio_get()/bio_put() from the blkdev_issue_discard() since
bio_alloc() and bio_batch_end_io() is doing the same thing, hence it is
not needed anymore.
I have done simple dd testing with surprising results. The script I have
used is:
for i in $(seq 10); do
echo $i
dd if=/dev/sdb1 of=/dev/sdc1 bs=4k &
sleep 5
done
/usr/bin/time -f %e ./blkdiscard /dev/sdc1
Running time of BLKDISCARD on the whole device:
with patch without patch
0.95 15.58
So we can see that in this artificial test the kernel with the patch
applied is approx 16x faster in discarding the device.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
CC: Dmitry Monakhov <dmonakhov@openvz.org>
CC: Jens Axboe <jaxboe@fusionio.com>
CC: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In some drives, flush requests are non-queueable. When flush request is
running, normal read/write requests can't run. If block layer dispatches
such request, driver can't handle it and requeue it. Tejun suggested we
can hold the queue when flush is running. This can avoid unnecessary
requeue. Also this can improve performance. For example, we have
request flush1, write1, flush 2. flush1 is dispatched, then queue is
hold, write1 isn't inserted to queue. After flush1 is finished, flush2
will be dispatched. Since disk cache is already clean, flush2 will be
finished very soon, so looks like flush2 is folded to flush1.
In my test, the queue holding completely solves a regression introduced by
commit 53d63e6b0dfb95882ec0219ba6bbd50cde423794:
block: make the flush insertion use the tail of the dispatch list
It's not a preempt type request, in fact we have to insert it
behind requests that do specify INSERT_FRONT.
which causes about 20% regression running a sysbench fileio
workload.
Stable: 2.6.39 only
Cc: stable@kernel.org
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
flush request isn't queueable in some drives. Add a flag to let driver
notify block layer about this. We can optimize flush performance with the
knowledge.
Stable: 2.6.39 only
Cc: stable@kernel.org
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
After the anticipatory scheduler was dropped, there was no need to
special-case the request_module string. As such, drop the redundant
sprintf and stack variable.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
unplug is replaced with blk_run_queue now in blk_execute_rq_nowait,
so change the comment accordingly.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
DISK_EVENT_MEDIA_CHANGE is used for both userland visible event and
internal event for revalidation of removeable devices. Some legacy
drivers don't implement proper event detection and continuously
generate events under certain circumstances. For example, ide-cd
generates media changed continuously if there's no media in the drive,
which can lead to infinite loop of events jumping back and forth
between the driver and userland event handler.
This patch updates disk event infrastructure such that it never
propagates events not listed in disk->events to userland. Those
events are processed the same for internal purposes but uevent
generation is suppressed.
This also ensures that userland only gets events which are advertised
in the @events sysfs node lowering risk of confusion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The sort insert is the one that goes to the IO scheduler. With
the SORT_MERGE addition, we could bypass IO scheduler setup
but still ask the IO scheduler to insert the request. This would
cause an oops on switching IO schedulers through the sysfs
interface, unless the disk just happened to be idle while it
occured.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In queue_requests_store, the code looks like
if (rl->count[BLK_RW_SYNC] >= q->nr_requests) {
blk_set_queue_full(q, BLK_RW_SYNC);
} else if (rl->count[BLK_RW_SYNC]+1 <= q->nr_requests) {
blk_clear_queue_full(q, BLK_RW_SYNC);
wake_up(&rl->wait[BLK_RW_SYNC]);
}
If we don't satify the situation of "if", we can get that
rl->count[BLK_RW_SYNC} < q->nr_quests. It is the same as
rl->count[BLK_RW_SYNC]+1 <= q->nr_requests.
All the "else" should satisfy the "else if" check so it isn't
needed actually.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We do not call blk_trace_remove_sysfs() in err return path
if kobject_add() fails. This path fixes it.
Cc: stable@kernel.org
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We don't pass in a 'force_kblockd' anymore, get rid of the
stsale comment.
Reported-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We are currently using this flag to check whether it's safe
to call into ->request_fn(). If it is set, we punt to kblockd.
But we get a lot of false positives and excessive punts to
kblockd, which hurts performance.
The only real abuser of this infrastructure is SCSI. So export
the async queue run and convert SCSI over to use that. There's
room for improvement in that SCSI need not always use the async
call, but this fixes our performance issue and they can fix that
up in due time.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
For some configurations of CONFIG_PREEMPT that is not true. So
get rid of __call_for_each_cic() and always uses the explicitly
rcu_read_lock() protected call_for_each_cic() instead.
This fixes a potential bug related to IO scheduler removal or
online switching.
Thanks to Paul McKenney for clarifying this.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
With all drivers and file systems converted, we only have
in-core use of this function. So remove the export.
Reporteed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If we know we are going to punt to kblockd, we can drop the queue
lock before calling into __blk_run_queue() since it only does a
safe bit test and a workqueue call. Since kblockd needs to grab
this very lock as one of the first things it does, it's a good
optimization to drop the lock before waking kblockd.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
MD can't use this since it really requires us to be able to
keep more than a single piece of state for the unplug. Commit
048c9374 added the required support for MD, so get rid of this
now unused code.
This reverts commit f75664570d.
Conflicts:
block/blk-core.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
md/raid requires an unplug callback, but as it does not uses
requests the current code cannot provide one.
So allow arbitrary callbacks to be attached to the blk_plug.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It's a pretty close match to what we had before - the timer triggering
would mean that nobody unplugged the plug in due time, in the new
scheme this matches very closely what the schedule() unplug now is.
It's essentially the difference between an explicit unplug (IO unplug)
or an implicit unplug (timer unplug, we scheduled with pending IO
queued).
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
For the explicit unplugging, we'd prefer to kick things off
immediately and not pay the penalty of the latency to switch
to kblockd. So let blk_finish_plug() do the run inline, while
the implicit-on-schedule-out unplug will punt to kblockd.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It's a bit of a mess currently. task->plug is being cleared
and reset in __blk_finish_plug(), and blk_finish_plug() is
testing for a NULL plug which cannot happen even from schedule()
anymore since it uses blk_needs_flush_plug() to determine
whether to call into this function at all.
So get rid of some of the cruft.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In the function blk_register_queue(), var _dev_ is already assigned by
disk_to_dev().So use it directly instead of calling disk_to_dev() again.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Modified by me to delete an empty line in the same function while
in there anyway.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
There are worries that we are now consuming a lot more stack in
some cases, since we potentially call into IO dispatch from
schedule() or io_schedule(). We can reduce this problem by moving
the running of the queue to kblockd, like the old plugging scheme
did as well.
This may or may not be a good idea from a performance perspective,
depending on how many tasks have queue plugs running at the same
time. For even the slightly contended case, doing just a single
queue run from kblockd instead of multiple runs directly from the
unpluggers will be faster.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The original use for this dates back to when we had to track write
requests for serializing around barriers. That's not needed anymore,
so kill it.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This was removed with the queue plug state. But we can easily readd
by checking if this is the first request going to this queue. It's
good information to have when tracing to see how effective the
plugging is.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
MD would like to know when a queue is unplugged, so it can flush
it's bitmap writes. Add such a callback.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It was removed with the on-stack plugging, readd it and track the
depth of requests added when flushing the plug.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If the request_fn ends up blocking, we could be re-entering
the plug flush. Since the list is protected by explicitly
not allowing schedule events, this isn't a terribly good idea.
Additionally, it can cause us to recurse. As request_fn called by
__blk_run_queue is allowed to 'schedule()' (after dropping the queue
lock of course), it is possible to get a recursive call:
schedule -> blk_flush_plug -> __blk_finish_plug -> flush_plug_list
-> __blk_run_queue -> request_fn -> schedule
We must make sure that the second schedule does not call into
blk_flush_plug again. So instead of leaving the list of requests on
blk_plug->list, move them to a separate list leaving blk_plug->list
empty.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Comparison function for list_sort() must be anticommutative,
otherwise it is not sorting in ordinary meaning.
But fortunately list_sort() always check ((*cmp)(priv, a, b) <= 0)
it not distinguish negative and zero, so comparison function can
implement only less-or-equal instead of full three-way comparison.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The current block integrity (DIF/DIX) support in DM is verifying that
all devices' integrity profiles match during DM device resume (which
is past the point of no return). To some degree that is unavoidable
(stacked DM devices force this late checking). But for most DM
devices (which aren't stacking on other DM devices) the ideal time to
verify all integrity profiles match is during table load.
Introduce the notion of an "initialized" integrity profile: a profile
that was blk_integrity_register()'d with a non-NULL 'blk_integrity'
template. Add blk_integrity_is_initialized() to allow checking if a
profile was initialized.
Update DM integrity support to:
- check all devices with _initialized_ integrity profiles match
during table load; uninitialized profiles (e.g. for underlying DM
device(s) of a stacked DM device) are ignored.
- disallow a table load that would result in an integrity profile that
conflicts with a DM device's existing (in-use) integrity profile
- avoid clearing an existing integrity profile
- validate all integrity profiles match during resume; but if they
don't all we can do is report the mismatch (during resume we're past
the point of no return)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
xchg does not work portably with smaller than 32bit types.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It's not a preempt type request, in fact we have to insert it
behind requests that do specify INSERT_FRONT.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Merge it with __elv_add_request(), it's pretty pointless to
have a function with only two callers. The main interface
is elv_add_request()/__elv_add_request().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently we just dump a non-informative 'request botched' message.
Lets actually try and print something sane to help debug issues
around this.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When the queue work handler was converted to delayed work, the
stopping was inadvertently made sync as well. Change this back
to being async stop, using __cancel_delayed_work() instead of
cancel_delayed_work().
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Reported-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
With the introduction of the on-stack plugging, we would assume
that any request being inserted was a normal file system request.
As flush/fua requires a special insert mode, this caused problems.
Fix this up by checking for this in flush_plug_list() and use
the appropriate insert mechanism.
Big thanks goes to Markus Tripplesdorf for tirelessly testing
patches, and to Sergey Senozhatsky for helping find the real
issue.
Reported-by: Markus Tripplesdorf <markus@trippelsdorf.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
Removing think time checking. A high thinktime queue might means the queue
dispatches several requests and then do away. Limitting such queue seems
meaningless. And also this can simplify code. This is suggested by Vivek.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
For v2, I added back lines to cfq_preempt_queue() that were removed
during updates for accounting unaccounted_time. Thanks for pointing out
that I'd missed these, Vivek.
Previous commit "cfq-iosched: Don't set active queue in preempt" wrongly
cleared stats for preempting queues when it shouldn't have, because when
we choose a queue to preempt, it still isn't necessarily scheduled next.
Thanks to Vivek Goyal for figuring this out and understanding how the
preemption code works.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Lina reported that if throttle limits are initially very high and then
dropped, then no new bio might be dispatched for a long time. And the
reason being that after dropping the limits we don't reset the existing
slice and do the rate calculation with new low rate and account the bios
dispatched at high rate. To fix it, reset the slice upon rate change.
https://lkml.org/lkml/2011/3/10/298
Another problem with very high limit is that we never queued the
bio on throtl service tree. That means we kept on extending the
group slice but never trimmed it. Fix that also by regulary
trimming the slice even if bio is not being queued up.
Reported-by: Lina Lu <lulina_nuaa@foxmail.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This change moves unaccounted_time to only be reported when
CONFIG_DEBUG_BLK_CGROUP is true.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit "Add unaccounted time to timeslice_used" changed the behavior of
cfq_preempt_queue to set cfqq active. Vivek pointed out that other
preemption rules might get involved, so we shouldn't manually set which
queue is active.
This cleans up the code to just clear the queue stats at preemption
time.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
One of the disadvantages of on-stack plugging is that we potentially
lose out on merging since all pending IO isn't always visible to
everybody. When we flush the on-stack plugs, right now we don't do
any checks to see if potential merge candidates could be utilized.
Correct this by adding a new insert variant, ELEVATOR_INSERT_SORT_MERGE.
It works just ELEVATOR_INSERT_SORT, but first checks whether we can
merge with an existing request before doing the insertion (if we fail
merging).
This fixes a regression with multiple processes issuing IO that
can be merged.
Thanks to Shaohua Li <shaohua.li@intel.com> for testing and fixing
an accounting bug.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
Version 3 is updated to apply to for-2.6.39/core.
For version 2, I took Vivek's advice and made sure we update the group
weight from cfq_group_service_tree_add().
If a weight was updated while a group is on the service tree, the
calculation for the total weight of the service tree can be adjusted
improperly, which either leads to bad service tree weights, or
potentially crashes (if total_weight becomes 0).
This patch defers updates to the weight until a group is off the service
tree.
Signed-off-by: Justin TerAvest <teravest@google.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
There are two kind of times that tasks are not charged for: the first
seek and the extra time slice used over the allocated timeslice. Both
of these exported as a new unaccounted_time stat.
I think it would be good to have this reported in 'time' as well, but
that is probably a separate discussion.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
barrier is already removed, so remove the obsolete comments
in blkdev_issue_zeroout.
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
BZ29402
https://bugzilla.kernel.org/show_bug.cgi?id=29402
We can hit serious mis-synchronization in bio completion path of
blkdev_issue_zeroout() leading to a panic.
The problem is that when we are going to wait_for_completion() in
blkdev_issue_zeroout() we check if the bb.done equals issued (number of
submitted bios). If it does, we can skip the wait_for_completition()
and just out of the function since there is nothing to wait for.
However, there is a ordering problem because bio_batch_end_io() is
calling atomic_inc(&bb->done) before complete(), hence it might seem to
blkdev_issue_zeroout() that all bios has been completed and exit. At
this point when bio_batch_end_io() is going to call complete(bb->wait),
bb and wait does not longer exist since it was allocated on stack in
blkdev_issue_zeroout() ==> panic!
(thread 1) (thread 2)
bio_batch_end_io() blkdev_issue_zeroout()
if(bb) { ...
if (bb->end_io) ...
bb->end_io(bio, err); ...
atomic_inc(&bb->done); ...
... while (issued != atomic_read(&bb.done))
... (let issued == bb.done)
... (do the rest of the function)
... return ret;
complete(bb->wait);
^^^^^^^^
panic
We can fix this easily by simplifying bio_batch and completion counting.
Also remove bio_end_io_t *end_io since it is not used.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reported-by: Eric Whitney <eric.whitney@hp.com>
Tested-by: Eric Whitney <eric.whitney@hp.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
CC: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Use plug in throttle dispatch also as we are dispatching a bunch of
bios in throttle context and some of them might merge.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
With the plugging now being explicitly controlled by the
submitter, callers need not pass down unplugging hints
to the block layer. If they want to unplug, it's because they
manually plugged on their own - in which case, they should just
unplug at will.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch adds support for creating a queuing context outside
of the queue itself. This enables us to batch up pieces of IO
before grabbing the block device queue lock and submitting them to
the IO scheduler.
The context is created on the stack of the process and assigned in
the task structure, so that we can auto-unplug it if we hit a schedule
event.
The current queue plugging happens implicitly if IO is submitted to
an empty device, yet callers have to remember to unplug that IO when
they are going to wait for it. This is an ugly API and has caused bugs
in the past. Additionally, it requires hacks in the vm (->sync_page()
callback) to handle that logic. By switching to an explicit plugging
scheme we make the API a lot nicer and can get rid of the ->sync_page()
hack in the vm.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Currently, disk_unblock_events() implicitly kick event check if the
block count reaches zero. This behavior is not described in the
comment and hinders with future changes. Make the unblocker
explicitly check events by calling disk_check_events() as necessary.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
We've found that we still get good, useful isolation at weights this
low. I'd like to adjust the minimum so that any other changes can take
these values into account.
Signed-off-by: Justin TerAvest <teravest@google.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When throttle group limits are updated through cgroups, a thread is
woken up to process these updates. While reviewing that code, oleg noted
couple of race conditions existed in the code and he also suggested that
code can be simplified.
This patch fixes the races simplifies the code based on Oleg's suggestions:
- Use xchg().
- Introduced a common function throtl_update_blkio_group_common()
which is shared now by all iops/bps update functions.
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Fixed a merge issue, throtl_schedule_delayed_work() takes throtl_data
as the argument now, not the queue.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
With the help of cgroup interface one can go and upate the bps/iops
limits of existing group. Once the limits are udpated, a thread is
woken up to see if some blocked group needs recalculation based on new
limits and needs to be requeued.
There was also a piece of code where I was checking for group limit
update when a fresh bio comes in. This patch gets rid of that piece of
code and keeps processing the limit change at one place
throtl_process_limit_change(). It just keeps the code simple and easy
to understand.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The update_vdisktime logic is broken since commit
b54ce60eb7, st->min_vdisktime never makes
a progress. Fix it.
Thanks Vivek for pointing it out.
Signed-off-by: Gui Jianfeng <guijianfen@cn.fujitsu.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If there are a sync and an async queue and the sync queue's think time
is small, we can ignore the sync queue's dispatch quantum. Because the
sync queue will always preempt the async queue, we don't need to care
about async's latency. This can fix a performance regression of
aiostress test, which is introduced by commit f8ae6e3eb8. The issue
should exist even without the commit, but the commit amplifies the
impact.
The initial post does the same optimization for RT queue too, but since
I have no real workload for it, Vivek suggests to drop it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This merge creates two set of conflicts. One is simple context
conflicts caused by removal of throtl_scheduled_delayed_work() in
for-linus and removal of throtl_shutdown_timer_wq() in
for-2.6.39/core.
The other is caused by commit 255bb490c8 (block: blk-flush shouldn't
call directly into q->request_fn() __blk_run_queue()) in for-linus
crashing with FLUSH reimplementation in for-2.6.39/core. The conflict
isn't trivial but the resolution is straight-forward.
* __blk_run_queue() calls in flush_end_io() and flush_data_end_io()
should be called with @force_kblockd set to %true.
* elv_insert() in blk_kick_flush() should use
%ELEVATOR_INSERT_REQUEUE.
Both changes are to avoid invoking ->request_fn() directly from
request completion path and closely match the changes in the commit
255bb490c8.
Signed-off-by: Tejun Heo <tj@kernel.org>
Move blk_throtl_exit() in blk_cleanup_queue() as blk_throtl_exit() is
written in such a way that it needs queue lock. In blk_release_queue()
there is no gurantee that ->queue_lock is still around.
Initially blk_throtl_exit() was in blk_cleanup_queue() but Ingo reported
one problem.
https://lkml.org/lkml/2010/10/23/86
And a quick fix moved blk_throtl_exit() to blk_release_queue().
commit 7ad58c0286
Author: Jens Axboe <jaxboe@fusionio.com>
Date: Sat Oct 23 20:40:26 2010 +0200
block: fix use-after-free bug in blk throttle code
This patch reverts above change and does not try to shutdown the
throtl work in blk_sync_queue(). By avoiding call to
throtl_shutdown_timer_wq() from blk_sync_queue(), we should also avoid
the problem reported by Ingo.
blk_sync_queue() seems to be used only by md driver and it seems to be
using it to make sure q->unplug_fn is not called as md registers its
own unplug functions and it is about to free up the data structures
used by unplug_fn(). Block throttle does not call back into unplug_fn()
or into md. So there is no need to cancel blk throttle work.
In fact I think cancelling block throttle work is bad because it might
happen that some bios are throttled and scheduled to be dispatched later
with the help of pending work and if work is cancelled, these bios might
never be dispatched.
Block layer also uses blk_sync_queue() during blk_cleanup_queue() and
blk_release_queue() time. That should be safe as we are also calling
blk_throtl_exit() which should make sure all the throttling related
data structures are cleaned up.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
There does not seem to be a clear convention whether q->queue_lock is
initialized or not when blk_cleanup_queue() is called. In the past it
was not necessary but now blk_throtl_exit() takes up queue lock by
default and needs queue lock to be available.
In fact elevator_exit() code also has similar requirement just that it
is less stringent in the sense that elevator_exit() is called only if
elevator is initialized.
Two problems have been noticed because of ambiguity about spin lock
status.
- If a driver calls blk_alloc_queue() and then soon calls
blk_cleanup_queue() almost immediately, (because some other
driver structure allocation failed or some other error happened)
then blk_throtl_exit() will run into issues as queue lock is not
initialized. Loop driver ran into this issue recently and I
noticed error paths in md driver too. Similar error paths should
exist in other drivers too.
- If some driver provided external spin lock and zapped the lock
before blk_cleanup_queue(), then it can lead to issues.
So this patch initializes the default queue lock at queue allocation time.
block throttling code is one of the users of queue lock and it is
initialized at the queue allocation time, so it makes sense to
initialize ->queue_lock also to internal lock. A driver can overide that
lock later. This will take care of the issue where a driver does not have
to worry about initializing the queue lock to default before calling
blk_cleanup_queue()
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Rename the numerals in the diskstats_show() into the macros.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
blk-flush decomposes a flush into sequence of multiple requests. On
completion of a request, the next one is queued; however, block layer
must not implicitly call into q->request_fn() directly from completion
path. This makes the queue behave unexpectedly when seen from the
drivers and violates the assumption that q->request_fn() is called
with process context + queue_lock.
This patch makes blk-flush the following two changes to make sure
q->request_fn() is not called directly from request completion path.
- blk_flush_complete_seq_end_io() now asks __blk_run_queue() to always
use kblockd instead of calling directly into q->request_fn().
- queue_next_fseq() uses ELEVATOR_INSERT_REQUEUE instead of
ELEVATOR_INSERT_FRONT so that elv_insert() doesn't try to unplug the
request queue directly.
Reported by Jan in the following threads.
http://thread.gmane.org/gmane.linux.ide/48778http://thread.gmane.org/gmane.linux.ide/48786
stable: applicable to v2.6.37.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
__blk_run_queue() automatically either calls q->request_fn() directly
or schedules kblockd depending on whether the function is recursed.
blk-flush implementation needs to be able to explicitly choose
kblockd. Add @force_kblockd.
All the current users are converted to specify %false for the
parameter and this patch doesn't introduce any behavior change.
stable: This is prerequisite for fixing ide oops caused by the new
blk-flush implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Effectively, make group_isolation=1 the default and remove the tunable.
The setting group_isolation=0 was because by default we idle on
sync-noidle tree and on fast devices, this can be very harmful for
throughput.
However, this problem can also be addressed by tuning slice_idle and
possibly group_idle on faster storage devices.
This change simplifies the CFQ code by removing the feature entirely.
Signed-off-by: Justin TerAvest <teravest@google.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
o Dominik Klein reported a system hang issue while doing some blkio
throttling testing.
https://lkml.org/lkml/2011/2/24/173
o Some tracing revealed that CFQ was not dispatching any more jobs as
queue unplug was not happening. And queue unplug was not happening
because unplug work was not being called as there was one throttling
work on same cpu which as not finished yet. And throttling work had not
finished as it was tyring to dispatch a bio to CFQ but all the request
descriptors were consume to it was put to sleep.
o So basically it is a cyclic dependecny between CFQ unplug work and
throtl dispatch work. Tejun suggested that use separate workqueue for
such cases.
o This patch uses a separate workqueue for throttle related work and
does not rely on kblockd workqueue anymore.
Cc: stable@kernel.org
Reported-by: Dominik Klein <dk@in-telegence.net>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://neil.brown.name/md:
md: Fix - again - partition detection when array becomes active
Fix over-zealous flush_disk when changing device size.
md: avoid spinlock problem in blk_throtl_exit
md: correctly handle probe of an 'mdp' device.
md: don't set_capacity before array is active.
md: Fix raid1->raid0 takeover
Adam Kovari and others reported that disconnecting an USB drive with
an ntfs-3g filesystem would cause "kernel BUG at fs/inode.c:1421!" to
be triggered.
The BUG could be traced back to ioctl(BLKBSZSET), which would
erroneously decrement the refcount on the bdev. This is because
blkdev_get() expects the refcount to be already incremented and either
returns success or decrements the refcount and returns an error.
The bug was introduced by e525fd89 (block: make blkdev_get/put()
handle exclusive access), which didn't take into account this behavior
of blkdev_get().
This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=29202
(and likely 29792 too)
Reported-by: Adam Kovari <kovariadam@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two cases when we call flush_disk.
In one, the device has disappeared (check_disk_change) so any
data will hold becomes irrelevant.
In the oter, the device has changed size (check_disk_size_change)
so data we hold may be irrelevant.
In both cases it makes sense to discard any 'clean' buffers,
so they will be read back from the device if needed.
In the former case it makes sense to discard 'dirty' buffers
as there will never be anywhere safe to write the data. In the
second case it *does*not* make sense to discard dirty buffers
as that will lead to file system corruption when you simply enlarge
the containing devices.
flush_disk calls __invalidate_devices.
__invalidate_device calls both invalidate_inodes and invalidate_bdev.
invalidate_inodes *does* discard I_DIRTY inodes and this does lead
to fs corruption.
invalidate_bev *does*not* discard dirty pages, but I don't really care
about that at present.
So this patch adds a flag to __invalidate_device (calling it
__invalidate_device2) to indicate whether dirty buffers should be
killed, and this is passed to invalidate_inodes which can choose to
skip dirty inodes.
flusk_disk then passes true from check_disk_change and false from
check_disk_size_change.
dm avoids tripping over this problem by calling i_size_write directly
rathher than using check_disk_size_change.
md does use check_disk_size_change and so is affected.
This regression was introduced by commit 608aeef17a which causes
check_disk_size_change to call flush_disk, so it is suitable for any
kernel since 2.6.27.
Cc: stable@kernel.org
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
Classify severity of I/O errors for target, nexus, and
transport errors.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Flush requests are never put on the IO scheduler. Convert request
structure's elevator_private* into an array and have the flush fields
share a union with it.
Reclaim the space lost in 'struct request' by moving 'completion_data'
back in the union with 'rb_node'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Skip elevator initialization for flush requests by passing priv=0 to
blk_alloc_request() in get_request(). As such elv_set_request() is
never called for flush requests.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cdrom: support devices that have check_events but not media_changed
cfq-iosched: Don't wait if queue already has requests.
blkio-throttle: Avoid calling blkiocg_lookup_group() for root group
cfq: rename a function to give it more appropriate name
cciss: make cciss_revalidate not loop through CISS_MAX_LUNS volumes unnecessarily.
drivers/block/aoe/Makefile: replace the use of <module>-objs with <module>-y
loop: queue_lock NULL pointer derefence in blk_throtl_exit
drivers/block/Makefile: replace the use of <module>-objs with <module>-y
blktrace: Don't output messages if NOTIFY isn't set.
Commit 7667aa0630 added logic to wait for
the last queue of the group to become busy (have at least one request),
so that the group does not lose out for not being continuously
backlogged. The commit did not check for the condition that the last
queue already has some requests. As a result, if the queue already has
requests, wait_busy is set. Later on, cfq_select_queue() checks the
flag, and decides that since the queue has a request now and wait_busy
is set, the queue is expired. This results in early expiration of the
queue.
This patch fixes the problem by adding a check to see if queue already
has requests. If it does, wait_busy is not set. As a result, time slices
do not expire early.
The queues with more than one request are usually buffered writers.
Testing shows improvement in isolation between buffered writers.
Cc: stable@kernel.org
Signed-off-by: Justin TerAvest <teravest@google.com>
Reviewed-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The current FLUSH/FUA support has evolved from the implementation
which had to perform queue draining. As such, sequencing is done
queue-wide one flush request after another. However, with the
draining requirement gone, there's no reason to keep the queue-wide
sequential approach.
This patch reimplements FLUSH/FUA support such that each FLUSH/FUA
request is sequenced individually. The actual FLUSH execution is
double buffered and whenever a request wants to execute one for either
PRE or POSTFLUSH, it queues on the pending queue. Once certain
conditions are met, a flush request is issued and on its completion
all pending requests proceed to the next sequence.
This allows arbitrary merging of different type of flushes. How they
are merged can be primarily controlled and tuned by adjusting the
above said 'conditions' used to determine when to issue the next
flush.
This is inspired by Darrick's patches to merge multiple zero-data
flushes which helps workloads with highly concurrent fsync requests.
* As flush requests are never put on the IO scheduler, request fields
used for flush share space with rq->rb_node. rq->completion_data is
moved out of the union. This increases the request size by one
pointer.
As rq->elevator_private* are used only by the iosched too, it is
possible to reduce the request size further. However, to do that,
we need to modify request allocation path such that iosched data is
not allocated for flush requests.
* FLUSH/FUA processing happens on insertion now instead of dispatch.
- Comments updated as per Vivek and Mike.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
bio's for flush are completed twice - once during the data phase and
one more time after the whole sequence is complete. The first
completion shouldn't notify completion to the issuer.
This was achieved by skipping all bio completion steps in
req_bio_endio() for the first completion; however, this has two
drawbacks.
* Error is not recorded in bio and must be tracked somewhere else.
* Partial completion is not supported.
Both don't cause problems for the current users; however, they make
further improvements difficult. Change req_bio_endio() such that it
only skips the actual notification part for the first completion. bio
completion is implemented with partial completions on mind anyway so
this is as simple as moving the REQ_FLUSH_SEQ conditional such that
only calling of bio_endio() is skipped.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
rq == &q->flush_rq was used to determine whether a rq is part of a
flush sequence, which worked because all requests in a flush sequence
were sequenced using the single dedicated request. This is about to
change, so introduce REQ_FLUSH_SEQ flag to distinguish flush sequence
requests.
This patch doesn't cause any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o Jeff Moyer was doing some testing on a RAM backed disk and
blkiocg_lookup_group() showed up high overhead after memcpy(). Similarly
somebody else reported that blkiocg_lookup_group() is eating 6% extra
cpu. Though looking at the code I can't think why the overhead of
this function is so high. One thing is that it is called with very high
frequency (once for every IO).
o For lot of folks blkio controller will be compiled in but they might
not have actually created cgroups. Hence optimize the case of root
cgroup where we can avoid calling blkiocg_lookup_group() if IO is happening
in root group (common case).
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
o Rename a function to give it more approprate name. We are calculating
cfq queue slice and function name gives the impression as if cfq group
slice length is being calculated.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If a queue is preempted before it gets slice assigned, the queue doesn't get
compensation, which looks unfair. For such queue, we compensate it for a whole
slice.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
I got this:
fio-874 [007] 2157.724514: 8,32 m N cfq874 preempt
fio-874 [007] 2157.724519: 8,32 m N cfq830 slice expired t=1
fio-874 [007] 2157.724520: 8,32 m N cfq830 sl_used=1 disp=0 charge=1 iops=0 sect=0
fio-874 [007] 2157.724521: 8,32 m N cfq830 set_active wl_prio:0 wl_type:0
fio-874 [007] 2157.724522: 8,32 m N cfq830 Not idling. st->count:1
cfq830 is an async queue, and preempted by a sync queue cfq874. But since we
have cfqg->saved_workload_slice mechanism, the preempt is a nop.
Looks currently our preempt is totally broken if the two queues are not from
the same workload type.
Below patch fixes it. This will might make async queue starvation, but it's
what our old code does before cgroup is added.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
cfq_group->ref is used with queue_lock hold, the only exception is
cfq_set_request, which looks like a bug to me, so ref doesn't need
to be an atomic and atomic operation is slower.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cfq_queue->ref is used with queue_lock hold, so ref doesn't need to be an atomic
and atomic operation is slower.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We can't use krefs since it's apparently restricted to very basic
reference counting.
This reverts commit e4a683c8.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Tejun Heo
Jens Axboe
Hannes Reinecke
Wanlong Gao
Andrew Morton
Suresh Jayaraman
Christoph Hellwig
Tao Ma
Jens Axboe
Wang Sheng-Hui
Nao Nishijima
Shaohua Li
Eric Seppanen
Linus Torvalds
Jeff Moyer
Akinobu Mita
Herbert Poetzl
Vivek Goyal
Mike Christie
Dan Williams
James Bottomley
Lai Jiangshan
Justin TerAvest
Mike Snitzer
Johannes Stezenbach
Namhyung Kim
Joe Perches
Wanlong Gao
Paul Bolle
Kyungmin Park
Ben Blum
Luca Tettamanti
James Bottomley
Martin K. Petersen
Lukas Czerner
Kees Cook
Liu Yuan
NeilBrown
Christoph Hellwig
Konstantin Khlebnikov
Andreas Schwab
Lucas De Marchi
Gui Jianfeng
Ben Hutchings
Miklos Szeredi
David Rientjes