This was the main impetus behind adding the PCI IRQ shim.
In order to properly order DMA writes wrt. interrupts, you have to
write to a PCI controller register, then poll for that bit clearing.
There is one bit for each interrupt source, and setting this register
bit tells Tomatillo to drain all pending DMA from that device.
Furthermore, Tomatillo's with revision less than 4 require us to do a
block store due to some memory transaction ordering issues it has on
JBUS.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a PCI controller to shim into IRQ delivery
so that DMA queues can be drained, if necessary.
If some bus specific code needs to run before an IRQ
handler is invoked, the bus driver simply needs to setup
the function pointer in bucket->irq_info->pre_handler and
the two args bucket->irq_info->pre_handler_arg[12].
The Schizo PCI driver is converted over to use a pre-handler
for the DMA write-sync processing it needs when a device
is behind a PCI->PCI bus deeper than the top-level APB
bridges.
While we're here, clean up all of the action allocation
and handling. Now, we allocate the irqaction as part of
the bucket->irq_info area. There is an array of 4 irqaction
(for PCI irq sharing) and a bitmask saying which entries
are active.
The bucket->irq_info is allocated at build_irq() time, not
at request_irq() time. This simplifies request_irq() and
free_irq() tremendously.
The SMP dynamic IRQ retargetting code got removed in this
change too. It was disabled for a few months now, and we
can resurrect it in the future if we want.
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch adds some ioctls to include/linux/compat_ioctl.h
to allow using ppdev from the 32 bit user space on sparc64.
This patch also adds the PPDEV option in the sparc64 menu, near Parallel
printer support in the 'General machine setup' submenu.
All those ioctls seem to be compatible, since (correct me if I'm wrong)
they dont use the 'long' type. See include/linux/ppdev.h.
The application I used to test the new ioctls only used the following:
PPEXCL
PPCLAIM
PPNEGOT
PPGETMODES
PPRCONTROL
PPWCONTROL
PPDATADIR
PPWDATA
PPRDATA
But I beleive that the other ioctls will work fine.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Catalin Marinas
The range for the ARMv6 block cache operations is inclusive but the
kernel doesn't re-calculate the end address, causing a page fault when
used (this only happens with support for cache aliasing, otherwise the
blk_flush_kern_dcache_page() is not called). This patch subtracts
L1_CACHE_BYTES from the end address.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes the bug that caused BUG_ON(!irqs_disabled()) to trigger in
run_posix_cpu_timers() on alpha/smp. We didn't disable interrupts
properly before calling smp_percpu_timer_interrupt().
We *do* disable interrupts everywhere except this unfortunate
smp_percpu_timer_interrupt(). Fixed thus.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep() instead of schedule_timeout() to guarantee the task
delays as expected. Neither signals nor wait-queue events are
important at this point in the code, I believe.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the magic address values in head.S more obvious as to where
they came from. Wrap all debug code in CONFIG_DEBUG_LL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The omnimeter_defconfig does not define any machines and
seems to have no other support in the current kernel.
This patch removes the config file, as this is the only
thing currently mentioning the ominmeter.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add support for PXA27x Standby mode, a low-power mode that retains CPU
and some peripheral state (the existing "sleep" mode is a power-power
mode that retains less state). Activated via:
echo -n standby > /sys/power/state
From: David Burrage and Todd Poynor
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As usual, the reason of this breakage is quite silly: in do_entIF, we
are checking for PS == 0 to see whether it was a kernel BUG() or
userspace trap.
It works, unless BUG() happens in interrupt - PS is not 0 in kernel mode
due to non-zero IPL, and the things get messed up horribly then. In
this particular case it was BUG_ON(!irqs_disabled()) triggered in
run_posix_cpu_timers(), so we ended up shooting "current" with the
bursts of one SIGTRAP and three SIGILLs on every timer tick. ;-)
Patch from Catalin Marinas
This patch fixes the V bit setting for the ARM1020x processors. At
reset, this bit is automatically set to the value of the HIVECSINIT
input signal which just happened to be 1 but it is not mandatory.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The new EABI gcc adds -mthumb-interwork by default, even if
-mabi=apcs-gnu is passed. This causes a warning for every compiled C
file when -march=armv4 is used. The patch adds -mno-thumb-interwork
if the option is supported. This is also useful since we don't need
any ARM/Thumb interworking in the kernel
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This patch fixes a broken comment in the proc-arm1020.S file which
prevents the file compilation
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Removed dead code in arch/xtensa/kernel/pci.c and use the pci_name() macro.
Fixed an error in the delay asm macro: '1' is an invalid immediate value.
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed an unnecessary local copy of zlib (sorry for the add'l traffic).
Fixed 'O=' support (thanks to Jan Dittmer for pointing it out). Some minor
clean-ups in the make files.
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added 'mm/Kconfig' to the xtensa Kconfig file to get a flat memory layout.
Fixed a typo in one of the help texts (thanks Geert for pointing it out)
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
xtensa should use valid_signal() instead of testing _NSIG directly like
everyone else.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Editor snafu in which the call to ppc_sys_get_pdata got inside the if check
instead of before it. Oops.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we receive an unrecognised abort during boot, don't try to
send a signal to pid0, but instead report the current state.
This leads to less confusing debug reports.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The hvlpevent_queue (formally ItLpQueue) has a member called xInUseWord
which is used for serialising access to the queue. Because it's a word
(ie. 32 bit) there's a custom 32-bit version of test_and_set_bit() or
thereabouts in ItLpQueue.c.
The xInUseWord is not shared with they hypervisor, so we can replace it
with a spinlock and remove the custom code.
There is also another locking mechanism (ItLpQueueInProcess). This is
redundant because it's only manipulated while the lock's held. Remove it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just formatting cleanups:
* rename some "nextLpEvent" variables to just "event"
* make code fit in 80 columns
* use brackets around if/else
* use a temporary to make hvlpevent_clear_valid clearer
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just cleanup white space.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code that prints event counts by type uses a hand-coded number of tabs
to get the alignment right. Instead use a printf alignment which will allow
allow us to use the event_type strings elsewhere in the future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently there's a per-cpu count of lpevents processed, a per-queue (ie.
global) total count, and a count by event type.
Replace all that with a count by event for each cpu. We only need to add
it up int the proc code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we count the number of lpevents processed in 3 seperate places.
One of these counters is never read, so just remove it. This means
hvlpevent_queue_process() no longer needs to return the number of events
processed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we've renamed the xItLpQueue structure, rename the functions that
operate on it also.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The xItLpQueue is a queue of HvLpEvents that we're given by the Hypervisor.
Rename xItLpQueue to hvlpevent_queue and make the type struct hvlpevent_queue.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The xItLpQueue is declared in LparData.c, move it into ItLpQueue.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
External parties don't need to use ItLpQueue_getNextLpEvent() or
ItLpQueue_clearValid(), they're internal to ItLpQueue.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the code that displays xItLpQueue values in /proc into
ItLpQueue.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The xItLpQueue is initalised manually in iSeries_setup_arch(). Move
this code into ItLpQueue.c for a cleaner separation.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because there's only one ItLpQueue and we know where it is, ie. xItLpQueue,
there's no point passing pointers to it it around all over the place.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the macros that initialise the paca to remove the lpq
parameter. It also rearranges them a bit with the hope of making them a
bit clearer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The only code outside ItLpQueue.c that refers to spread_lpevents is in
set_apread_lpevents(), so move it inside ItLpQueue.c and make spread_lpevents
static.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the previous patch in place, spreading lpevents by default becomes
a one liner.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The iSeries code keeps a pointer to the ItLpQueue in its paca struct. But
all these pointers end up pointing to the one place, ie. xItLpQueue.
So remove the pointer from the paca struct and just refer to xItLpQueue
directly where needed.
The only complication is that the spread_lpevents logic was implemented by
having a NULL lpqueue pointer in the paca on CPUs that weren't supposed to
process events. Instead we just compare the spread_lpevents value to the
processor id to get the same behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
VFP used __divdi3 64-bit division needlessly. Convert it to use
our 64-bit by 32-bit division instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds support for Dynamic Tick Timer for OMAP.
This patch is an updated version of ARM patch 2642/1 to
make it work with the already integrated generic ARM
dyntick support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
