[ARM] 5130/4: Support for the at91sam9g20

Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit is contained in:
sedji gaouaou 2008-07-10 10:15:35 +01:00 committed by Russell King
parent 16074b669e
commit 613526677a
16 changed files with 342 additions and 29 deletions

View file

@ -30,6 +30,11 @@ config ARCH_AT91SAM9RL
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
config ARCH_AT91SAM9G20
bool "AT91SAM9G20"
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
config ARCH_AT91CAP9
bool "AT91CAP9"
select GENERIC_TIME
@ -239,6 +244,20 @@ endif
# ----------------------------------------------------------
if ARCH_AT91SAM9G20
comment "AT91SAM9G20 Board Type"
config MACH_AT91SAM9G20EK
bool "Atmel AT91SAM9G20-EK Evaluation Kit"
depends on ARCH_AT91SAM9G20
help
Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit.
endif
# ----------------------------------------------------------
if ARCH_AT91CAP9
comment "AT91CAP9 Board Type"
@ -274,13 +293,13 @@ comment "AT91 Board Options"
config MTD_AT91_DATAFLASH_CARD
bool "Enable DataFlash Card support"
depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK || MACH_SAM9_L9260 || MACH_ECBAT91)
depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK)
help
Enable support for the DataFlash card.
config MTD_NAND_AT91_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK)
help
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
@ -329,15 +348,15 @@ config AT91_EARLY_USART2
config AT91_EARLY_USART3
bool "USART3"
depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260)
depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20)
config AT91_EARLY_USART4
bool "USART4"
depends on ARCH_AT91SAM9260
depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20
config AT91_EARLY_USART5
bool "USART5"
depends on ARCH_AT91SAM9260
depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20
endchoice

View file

@ -15,6 +15,7 @@ obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_d
obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o
obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o
obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o
obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
obj-$(CONFIG_ARCH_AT91CAP9) += at91cap9.o at91sam926x_time.o at91cap9_devices.o
obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
@ -49,6 +50,9 @@ obj-$(CONFIG_MACH_USB_A9263) += board-usb-a9263.o
# AT91SAM9RL board-specific support
obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o
# AT91SAM9G20 board-specific support
obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
# AT91CAP9 board-specific support
obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o

View file

@ -47,6 +47,20 @@ static struct map_desc at91sam9260_sram_desc[] __initdata = {
}
};
static struct map_desc at91sam9g20_sram_desc[] __initdata = {
{
.virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE,
.pfn = __phys_to_pfn(AT91SAM9G20_SRAM0_BASE),
.length = AT91SAM9G20_SRAM0_SIZE,
.type = MT_DEVICE,
}, {
.virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE - AT91SAM9G20_SRAM1_SIZE,
.pfn = __phys_to_pfn(AT91SAM9G20_SRAM1_BASE),
.length = AT91SAM9G20_SRAM1_SIZE,
.type = MT_DEVICE,
}
};
static struct map_desc at91sam9xe_sram_desc[] __initdata = {
{
.pfn = __phys_to_pfn(AT91SAM9XE_SRAM_BASE),
@ -307,6 +321,8 @@ void __init at91sam9260_initialize(unsigned long main_clock)
if (cpu_is_at91sam9xe())
at91sam9xe_initialize();
else if (cpu_is_at91sam9g20())
iotable_init(at91sam9g20_sram_desc, ARRAY_SIZE(at91sam9g20_sram_desc));
else
iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc));

View file

@ -18,6 +18,7 @@
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
#include <asm/arch/cpu.h>
#include <asm/arch/at91sam9260.h>
#include <asm/arch/at91sam9260_matrix.h>
#include <asm/arch/at91sam9_smc.h>
@ -320,20 +321,41 @@ void __init at91_add_device_nand(struct at91_nand_data *data)
csa = at91_sys_read(AT91_MATRIX_EBICSA);
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
if (cpu_is_at91sam9260()) {
/* Timing for sam9260 */
/* set the bus interface characteristics */
at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
if (data->bus_width_16)
mode = AT91_SMC_DBW_16;
else
mode = AT91_SMC_DBW_8;
at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
if (data->bus_width_16)
mode = AT91_SMC_DBW_16;
else
mode = AT91_SMC_DBW_8;
at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
}
if (cpu_is_at91sam9g20()) {
/* Timing for sam9g20 */
/* set the bus interface characteristics */
at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0)
| AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4)
| AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4));
at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
if (data->bus_width_16)
mode = AT91_SMC_DBW_16;
else
mode = AT91_SMC_DBW_8;
at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3));
}
/* enable pin */
if (data->enable_pin)

View file

@ -0,0 +1,218 @@
/*
* Copyright (C) 2005 SAN People
* Copyright (C) 2008 Atmel
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/at73c213.h>
#include <linux/clk.h>
#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
#include "generic.h"
static void __init ek_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91sam9260_initialize(18432000);
/* DGBU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
{
at91sam9260_init_interrupts(NULL);
}
/*
* USB Host port
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
};
/*
* USB Device port
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
};
/*
* SPI devices.
*/
static struct spi_board_info ek_spi_devices[] = {
#if !defined(CONFIG_MMC_AT91)
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 1,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
{ /* DataFlash card */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#endif
#endif
};
/*
* MACB Ethernet device
*/
static struct at91_eth_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PA7,
.is_rmii = 1,
};
/*
* NAND flash
*/
static struct mtd_partition __initdata ek_nand_partition[] = {
{
.name = "Bootstrap",
.offset = 0,
.size = 4 * 1024 * 1024,
},
{
.name = "Partition 1",
.offset = 4 * 1024 * 1024,
.size = 60 * 1024 * 1024,
},
{
.name = "Partition 2",
.offset = 64 * 1024 * 1024,
.size = MTDPART_SIZ_FULL,
},
};
static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(ek_nand_partition);
return ek_nand_partition;
}
/* det_pin is not connected */
static struct at91_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#endif
};
/*
* MCI (SD/MMC)
* det_pin, wp_pin and vcc_pin are not connected
*/
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1,
.wire4 = 1,
};
/*
* LEDs
*/
static struct gpio_led ek_leds[] = {
{ /* "bottom" led, green, userled1 to be defined */
.name = "ds5",
.gpio = AT91_PIN_PA6,
.active_low = 1,
.default_trigger = "none",
},
{ /* "power" led, yellow */
.name = "ds1",
.gpio = AT91_PIN_PA9,
.default_trigger = "heartbeat",
}
};
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
/* Maintainer: Atmel */
.phys_io = AT91_BASE_SYS,
.io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
.boot_params = AT91_SDRAM_BASE + 0x100,
.timer = &at91sam926x_timer,
.map_io = ek_map_io,
.init_irq = ek_init_irq,
.init_machine = ek_board_init,
MACHINE_END

View file

@ -515,14 +515,19 @@ static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq)
/*
* PLL input between 1MHz and 32MHz per spec, but lower
* frequences seem necessary in some cases so allow 100K.
* Warning: some newer products need 2MHz min.
*/
input = main_freq / i;
if (cpu_is_at91sam9g20() && input < 2000000)
continue;
if (input < 100000)
continue;
if (input > 32000000)
continue;
mul1 = out_freq / input;
if (cpu_is_at91sam9g20() && mul > 63)
continue;
if (mul1 > 2048)
continue;
if (mul1 < 2)
@ -582,7 +587,8 @@ int __init at91_clock_init(unsigned long main_clock)
/* report if PLLA is more than mildly overclocked */
plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR));
if (plla.rate_hz > 209000000)
if ((!cpu_is_at91sam9g20() && plla.rate_hz > 209000000)
|| (cpu_is_at91sam9g20() && plla.rate_hz > 800000000))
pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
/*
@ -597,7 +603,7 @@ int __init at91_clock_init(unsigned long main_clock)
uhpck.pmc_mask = AT91RM9200_PMC_UHP;
udpck.pmc_mask = AT91RM9200_PMC_UDP;
at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
udpck.pmc_mask = AT91SAM926x_PMC_UDP;
} else if (cpu_is_at91cap9()) {
@ -629,8 +635,13 @@ int __init at91_clock_init(unsigned long main_clock)
freq /= (1 << ((mckr & AT91_PMC_PRES) >> 2)); /* prescale */
if (cpu_is_at91rm9200())
mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
else
mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
else if (cpu_is_at91sam9g20()) {
mck.rate_hz = (mckr & AT91_PMC_MDIV) ?
freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq; /* mdiv ; (x >> 7) = ((x >> 8) * 2) */
if (mckr & AT91_PMC_PDIV)
freq /= 2; /* processor clock division */
} else
mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
/* Register the PMC's standard clocks */
for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++)

View file

@ -202,7 +202,7 @@ static int at91_pm_verify_clocks(void)
pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
return 0;
}
} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) {
pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
return 0;

View file

@ -180,8 +180,8 @@ config CPU_ARM925T
# ARM926T
config CPU_ARM926T
bool "Support ARM926T processor"
depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
select CPU_32v5
select CPU_ABRT_EV5TJ
select CPU_PABRT_NOIFAR

View file

@ -217,7 +217,7 @@ config MII
config MACB
tristate "Atmel MACB support"
depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9
depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91

View file

@ -888,7 +888,7 @@ static void pullup(struct at91_udc *udc, int is_on)
at91_udp_write(udc, AT91_UDP_TXVC, 0);
if (cpu_is_at91rm9200())
gpio_set_value(udc->board.pullup_pin, active);
else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) {
else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC);
txvc |= AT91_UDP_TXVC_PUON;
@ -906,7 +906,7 @@ static void pullup(struct at91_udc *udc, int is_on)
at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
if (cpu_is_at91rm9200())
gpio_set_value(udc->board.pullup_pin, !active);
else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) {
else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC);
txvc &= ~AT91_UDP_TXVC_PUON;

View file

@ -6,6 +6,8 @@
* Common definitions.
* Based on AT91SAM9260 datasheet revision A (Preliminary).
*
* Includes also definitions for AT91SAM9XE and AT91SAM9G families
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
@ -123,5 +125,14 @@
#define AT91SAM9XE_FLASH_BASE 0x00200000 /* Internal FLASH base address */
#define AT91SAM9XE_SRAM_BASE 0x00300000 /* Internal SRAM base address */
#define AT91SAM9G20_ROM_BASE 0x00100000 /* Internal ROM base address */
#define AT91SAM9G20_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */
#define AT91SAM9G20_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */
#define AT91SAM9G20_SRAM0_SIZE SZ_16K /* Internal SRAM 0 size (16Kb) */
#define AT91SAM9G20_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */
#define AT91SAM9G20_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */
#define AT91SAM9G20_UHP_BASE 0x00500000 /* USB Host controller */
#endif

View file

@ -77,7 +77,7 @@ struct at91_eth_data {
};
extern void __init at91_add_device_eth(struct at91_eth_data *data);
#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9)
#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9)
#define eth_platform_data at91_eth_data
#endif

View file

@ -21,6 +21,7 @@
#define ARCH_ID_AT91SAM9260 0x019803a0
#define ARCH_ID_AT91SAM9261 0x019703a0
#define ARCH_ID_AT91SAM9263 0x019607a0
#define ARCH_ID_AT91SAM9G20 0x019905a0
#define ARCH_ID_AT91SAM9RL64 0x019b03a0
#define ARCH_ID_AT91CAP9 0x039A03A0
@ -63,6 +64,12 @@ static inline unsigned long at91_arch_identify(void)
#define cpu_is_at91sam9260() (0)
#endif
#ifdef CONFIG_ARCH_AT91SAM9G20
#define cpu_is_at91sam9g20() (at91_cpu_identify() == ARCH_ID_AT91SAM9G20)
#else
#define cpu_is_at91sam9g20() (0)
#endif
#ifdef CONFIG_ARCH_AT91SAM9261
#define cpu_is_at91sam9261() (at91_cpu_identify() == ARCH_ID_AT91SAM9261)
#else

View file

@ -18,7 +18,7 @@
#if defined(CONFIG_ARCH_AT91RM9200)
#include <asm/arch/at91rm9200.h>
#elif defined(CONFIG_ARCH_AT91SAM9260)
#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)
#include <asm/arch/at91sam9260.h>
#elif defined(CONFIG_ARCH_AT91SAM9261)
#include <asm/arch/at91sam9261.h>

View file

@ -57,6 +57,11 @@
#define AT91SAM9_MASTER_CLOCK 100000000
#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
#elif defined(CONFIG_ARCH_AT91SAM9G20)
#define AT91SAM9_MASTER_CLOCK 132096000
#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
#elif defined(CONFIG_ARCH_AT91CAP9)
#define AT91CAP9_MASTER_CLOCK 100000000

View file

@ -41,7 +41,7 @@
#define DBG(x...)
#endif
#if defined(CONFIG_ARCH_AT91SAM9260)
#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)
#define NUM_SSC_DEVICES 1
#else
#define NUM_SSC_DEVICES 3