fbdev: bfin-lq035q1-fb: respect new PPI mode platform field

This lets us support the new BF527-EZKIT V2.1 via platform resources
tweaks only.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit is contained in:
Michael Hennerich 2010-05-24 14:33:52 -07:00 committed by Linus Torvalds
parent 5815e5d36e
commit fbd65e0ecd

View file

@ -61,47 +61,13 @@
#define LCD_X_RES 320 /* Horizontal Resolution */
#define LCD_Y_RES 240 /* Vertical Resolution */
#define DMA_BUS_SIZE 16
#define U_LINE 4 /* Blanking Lines */
#define USE_RGB565_16_BIT_PPI
#ifdef USE_RGB565_16_BIT_PPI
#define LCD_BPP 16 /* Bit Per Pixel */
#define CLOCKS_PER_PIX 1
#define CPLD_PIPELINE_DELAY_COR 0 /* NO CPLB */
#endif
/* Interface 16/18-bit TFT over an 8-bit wide PPI using a small Programmable Logic Device (CPLD)
* http://blackfin.uclinux.org/gf/project/stamp/frs/?action=FrsReleaseBrowse&frs_package_id=165
*/
#ifdef USE_RGB565_8_BIT_PPI
#define LCD_BPP 16 /* Bit Per Pixel */
#define CLOCKS_PER_PIX 2
#define CPLD_PIPELINE_DELAY_COR 3 /* RGB565 */
#endif
#ifdef USE_RGB888_8_BIT_PPI
#define LCD_BPP 24 /* Bit Per Pixel */
#define CLOCKS_PER_PIX 3
#define CPLD_PIPELINE_DELAY_COR 5 /* RGB888 */
#endif
/*
* HS and VS timing parameters (all in number of PPI clk ticks)
*/
#define U_LINE 4 /* Blanking Lines */
#define H_ACTPIX (LCD_X_RES * CLOCKS_PER_PIX) /* active horizontal pixel */
#define H_PERIOD (336 * CLOCKS_PER_PIX) /* HS period */
#define H_PULSE (2 * CLOCKS_PER_PIX) /* HS pulse width */
#define H_START (7 * CLOCKS_PER_PIX + CPLD_PIPELINE_DELAY_COR) /* first valid pixel */
#define V_LINES (LCD_Y_RES + U_LINE) /* total vertical lines */
#define V_PULSE (2 * CLOCKS_PER_PIX) /* VS pulse width (1-5 H_PERIODs) */
#define V_PERIOD (H_PERIOD * V_LINES) /* VS period */
#define ACTIVE_VIDEO_MEM_OFFSET ((U_LINE / 2) * LCD_X_RES * (LCD_BPP / 8))
#define BFIN_LCD_NBR_PALETTE_ENTRIES 256
@ -110,12 +76,6 @@
#define PPI_PORT_CFG_01 0x10
#define PPI_POLS_1 0x8000
#if (CLOCKS_PER_PIX > 1)
#define PPI_PMODE (DLEN_8 | PACK_EN)
#else
#define PPI_PMODE (DLEN_16)
#endif
#define LQ035_INDEX 0x74
#define LQ035_DATA 0x76
@ -139,6 +99,15 @@ struct bfin_lq035q1fb_info {
int irq;
spinlock_t lock; /* lock */
u32 pseudo_pal[16];
u32 lcd_bpp;
u32 h_actpix;
u32 h_period;
u32 h_pulse;
u32 h_start;
u32 v_lines;
u32 v_pulse;
u32 v_period;
};
static int nocursor;
@ -234,16 +203,69 @@ static int lq035q1_backlight(struct bfin_lq035q1fb_info *info, unsigned arg)
return 0;
}
static int bfin_lq035q1_calc_timing(struct bfin_lq035q1fb_info *fbi)
{
unsigned long clocks_per_pix, cpld_pipeline_delay_cor;
/*
* Interface 16/18-bit TFT over an 8-bit wide PPI using a small
* Programmable Logic Device (CPLD)
* http://blackfin.uclinux.org/gf/project/stamp/frs/?action=FrsReleaseBrowse&frs_package_id=165
*/
switch (fbi->disp_info->ppi_mode) {
case USE_RGB565_16_BIT_PPI:
fbi->lcd_bpp = 16;
clocks_per_pix = 1;
cpld_pipeline_delay_cor = 0;
break;
case USE_RGB565_8_BIT_PPI:
fbi->lcd_bpp = 16;
clocks_per_pix = 2;
cpld_pipeline_delay_cor = 3;
break;
case USE_RGB888_8_BIT_PPI:
fbi->lcd_bpp = 24;
clocks_per_pix = 3;
cpld_pipeline_delay_cor = 5;
break;
default:
return -EINVAL;
}
/*
* HS and VS timing parameters (all in number of PPI clk ticks)
*/
fbi->h_actpix = (LCD_X_RES * clocks_per_pix); /* active horizontal pixel */
fbi->h_period = (336 * clocks_per_pix); /* HS period */
fbi->h_pulse = (2 * clocks_per_pix); /* HS pulse width */
fbi->h_start = (7 * clocks_per_pix + cpld_pipeline_delay_cor); /* first valid pixel */
fbi->v_lines = (LCD_Y_RES + U_LINE); /* total vertical lines */
fbi->v_pulse = (2 * clocks_per_pix); /* VS pulse width (1-5 H_PERIODs) */
fbi->v_period = (fbi->h_period * fbi->v_lines); /* VS period */
return 0;
}
static void bfin_lq035q1_config_ppi(struct bfin_lq035q1fb_info *fbi)
{
bfin_write_PPI_DELAY(H_START);
bfin_write_PPI_COUNT(H_ACTPIX - 1);
bfin_write_PPI_FRAME(V_LINES);
unsigned ppi_pmode;
if (fbi->disp_info->ppi_mode == USE_RGB565_16_BIT_PPI)
ppi_pmode = DLEN_16;
else
ppi_pmode = (DLEN_8 | PACK_EN);
bfin_write_PPI_DELAY(fbi->h_start);
bfin_write_PPI_COUNT(fbi->h_actpix - 1);
bfin_write_PPI_FRAME(fbi->v_lines);
bfin_write_PPI_CONTROL(PPI_TX_MODE | /* output mode , PORT_DIR */
PPI_XFER_TYPE_11 | /* sync mode XFR_TYPE */
PPI_PORT_CFG_01 | /* two frame sync PORT_CFG */
PPI_PMODE | /* 8/16 bit data length / PACK_EN? */
ppi_pmode | /* 8/16 bit data length / PACK_EN? */
PPI_POLS_1); /* faling edge syncs POLS */
}
@ -272,19 +294,19 @@ static void bfin_lq035q1_stop_timers(void)
}
static void bfin_lq035q1_init_timers(void)
static void bfin_lq035q1_init_timers(struct bfin_lq035q1fb_info *fbi)
{
bfin_lq035q1_stop_timers();
set_gptimer_period(TIMER_HSYNC_id, H_PERIOD);
set_gptimer_pwidth(TIMER_HSYNC_id, H_PULSE);
set_gptimer_period(TIMER_HSYNC_id, fbi->h_period);
set_gptimer_pwidth(TIMER_HSYNC_id, fbi->h_pulse);
set_gptimer_config(TIMER_HSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT |
TIMER_TIN_SEL | TIMER_CLK_SEL|
TIMER_EMU_RUN);
set_gptimer_period(TIMER_VSYNC_id, V_PERIOD);
set_gptimer_pwidth(TIMER_VSYNC_id, V_PULSE);
set_gptimer_period(TIMER_VSYNC_id, fbi->v_period);
set_gptimer_pwidth(TIMER_VSYNC_id, fbi->v_pulse);
set_gptimer_config(TIMER_VSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT |
TIMER_TIN_SEL | TIMER_CLK_SEL |
TIMER_EMU_RUN);
@ -294,21 +316,21 @@ static void bfin_lq035q1_init_timers(void)
static void bfin_lq035q1_config_dma(struct bfin_lq035q1fb_info *fbi)
{
set_dma_config(CH_PPI,
set_bfin_dma_config(DIR_READ, DMA_FLOW_AUTO,
INTR_DISABLE, DIMENSION_2D,
DATA_SIZE_16,
DMA_NOSYNC_KEEP_DMA_BUF));
set_dma_x_count(CH_PPI, (LCD_X_RES * LCD_BPP) / DMA_BUS_SIZE);
set_dma_x_count(CH_PPI, (LCD_X_RES * fbi->lcd_bpp) / DMA_BUS_SIZE);
set_dma_x_modify(CH_PPI, DMA_BUS_SIZE / 8);
set_dma_y_count(CH_PPI, V_LINES);
set_dma_y_count(CH_PPI, fbi->v_lines);
set_dma_y_modify(CH_PPI, DMA_BUS_SIZE / 8);
set_dma_start_addr(CH_PPI, (unsigned long)fbi->fb_buffer);
}
#if (CLOCKS_PER_PIX == 1)
static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
P_PPI0_D0, P_PPI0_D1, P_PPI0_D2,
P_PPI0_D3, P_PPI0_D4, P_PPI0_D5,
@ -316,22 +338,27 @@ static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
P_PPI0_D9, P_PPI0_D10, P_PPI0_D11,
P_PPI0_D12, P_PPI0_D13, P_PPI0_D14,
P_PPI0_D15, 0};
#else
static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
static const u16 ppi0_req_8[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
P_PPI0_D0, P_PPI0_D1, P_PPI0_D2,
P_PPI0_D3, P_PPI0_D4, P_PPI0_D5,
P_PPI0_D6, P_PPI0_D7, 0};
#endif
static inline void bfin_lq035q1_free_ports(void)
static inline void bfin_lq035q1_free_ports(unsigned ppi16)
{
peripheral_free_list(ppi0_req_16);
if (ppi16)
peripheral_free_list(ppi0_req_16);
else
peripheral_free_list(ppi0_req_8);
if (ANOMALY_05000400)
gpio_free(P_IDENT(P_PPI0_FS3));
}
static int __devinit bfin_lq035q1_request_ports(struct platform_device *pdev)
static int __devinit bfin_lq035q1_request_ports(struct platform_device *pdev,
unsigned ppi16)
{
int ret;
/* ANOMALY_05000400 - PPI Does Not Start Properly In Specific Mode:
* Drive PPI_FS3 Low
*/
@ -342,7 +369,12 @@ static int __devinit bfin_lq035q1_request_ports(struct platform_device *pdev)
gpio_direction_output(P_IDENT(P_PPI0_FS3), 0);
}
if (peripheral_request_list(ppi0_req_16, DRIVER_NAME)) {
if (ppi16)
ret = peripheral_request_list(ppi0_req_16, DRIVER_NAME);
else
ret = peripheral_request_list(ppi0_req_8, DRIVER_NAME);
if (ret) {
dev_err(&pdev->dev, "requesting peripherals failed\n");
return -EFAULT;
}
@ -364,7 +396,7 @@ static int bfin_lq035q1_fb_open(struct fb_info *info, int user)
bfin_lq035q1_config_dma(fbi);
bfin_lq035q1_config_ppi(fbi);
bfin_lq035q1_init_timers();
bfin_lq035q1_init_timers(fbi);
/* start dma */
enable_dma(CH_PPI);
@ -402,12 +434,9 @@ static int bfin_lq035q1_fb_release(struct fb_info *info, int user)
static int bfin_lq035q1_fb_check_var(struct fb_var_screeninfo *var,
struct fb_info *info)
{
switch (var->bits_per_pixel) {
#if (LCD_BPP == 24)
case 24:/* TRUECOLOUR, 16m */
#else
case 16:/* DIRECTCOLOUR, 64k */
#endif
struct bfin_lq035q1fb_info *fbi = info->par;
if (var->bits_per_pixel == fbi->lcd_bpp) {
var->red.offset = info->var.red.offset;
var->green.offset = info->var.green.offset;
var->blue.offset = info->var.blue.offset;
@ -420,8 +449,7 @@ static int bfin_lq035q1_fb_check_var(struct fb_var_screeninfo *var,
var->red.msb_right = 0;
var->green.msb_right = 0;
var->blue.msb_right = 0;
break;
default:
} else {
pr_debug("%s: depth not supported: %u BPP\n", __func__,
var->bits_per_pixel);
return -EINVAL;
@ -528,6 +556,7 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
{
struct bfin_lq035q1fb_info *info;
struct fb_info *fbinfo;
u32 active_video_mem_offset;
int ret;
ret = request_dma(CH_PPI, DRIVER_NAME"_CH_PPI");
@ -550,6 +579,12 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, fbinfo);
ret = bfin_lq035q1_calc_timing(info);
if (ret < 0) {
dev_err(&pdev->dev, "Failed PPI Mode\n");
goto out3;
}
strcpy(fbinfo->fix.id, DRIVER_NAME);
fbinfo->fix.type = FB_TYPE_PACKED_PIXELS;
@ -571,46 +606,48 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
fbinfo->var.xres_virtual = LCD_X_RES;
fbinfo->var.yres = LCD_Y_RES;
fbinfo->var.yres_virtual = LCD_Y_RES;
fbinfo->var.bits_per_pixel = LCD_BPP;
fbinfo->var.bits_per_pixel = info->lcd_bpp;
if (info->disp_info->mode & LQ035_BGR) {
#if (LCD_BPP == 24)
fbinfo->var.red.offset = 0;
fbinfo->var.green.offset = 8;
fbinfo->var.blue.offset = 16;
#else
fbinfo->var.red.offset = 0;
fbinfo->var.green.offset = 5;
fbinfo->var.blue.offset = 11;
#endif
if (info->lcd_bpp == 24) {
fbinfo->var.red.offset = 0;
fbinfo->var.green.offset = 8;
fbinfo->var.blue.offset = 16;
} else {
fbinfo->var.red.offset = 0;
fbinfo->var.green.offset = 5;
fbinfo->var.blue.offset = 11;
}
} else {
#if (LCD_BPP == 24)
fbinfo->var.red.offset = 16;
fbinfo->var.green.offset = 8;
fbinfo->var.blue.offset = 0;
#else
fbinfo->var.red.offset = 11;
fbinfo->var.green.offset = 5;
fbinfo->var.blue.offset = 0;
#endif
if (info->lcd_bpp == 24) {
fbinfo->var.red.offset = 16;
fbinfo->var.green.offset = 8;
fbinfo->var.blue.offset = 0;
} else {
fbinfo->var.red.offset = 11;
fbinfo->var.green.offset = 5;
fbinfo->var.blue.offset = 0;
}
}
fbinfo->var.transp.offset = 0;
#if (LCD_BPP == 24)
fbinfo->var.red.length = 8;
fbinfo->var.green.length = 8;
fbinfo->var.blue.length = 8;
#else
fbinfo->var.red.length = 5;
fbinfo->var.green.length = 6;
fbinfo->var.blue.length = 5;
#endif
if (info->lcd_bpp == 24) {
fbinfo->var.red.length = 8;
fbinfo->var.green.length = 8;
fbinfo->var.blue.length = 8;
} else {
fbinfo->var.red.length = 5;
fbinfo->var.green.length = 6;
fbinfo->var.blue.length = 5;
}
fbinfo->var.transp.length = 0;
fbinfo->fix.smem_len = LCD_X_RES * LCD_Y_RES * LCD_BPP / 8
+ ACTIVE_VIDEO_MEM_OFFSET;
active_video_mem_offset = ((U_LINE / 2) * LCD_X_RES * (info->lcd_bpp / 8));
fbinfo->fix.smem_len = LCD_X_RES * LCD_Y_RES * info->lcd_bpp / 8
+ active_video_mem_offset;
fbinfo->fix.line_length = fbinfo->var.xres_virtual *
fbinfo->var.bits_per_pixel / 8;
@ -629,8 +666,8 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
goto out3;
}
fbinfo->screen_base = (void *)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET;
fbinfo->fix.smem_start = (int)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET;
fbinfo->screen_base = (void *)info->fb_buffer + active_video_mem_offset;
fbinfo->fix.smem_start = (int)info->fb_buffer + active_video_mem_offset;
fbinfo->fbops = &bfin_lq035q1_fb_ops;
@ -643,7 +680,8 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
goto out4;
}
ret = bfin_lq035q1_request_ports(pdev);
ret = bfin_lq035q1_request_ports(pdev,
info->disp_info->ppi_mode == USE_RGB565_16_BIT_PPI);
if (ret) {
dev_err(&pdev->dev, "couldn't request gpio port\n");
goto out6;
@ -693,7 +731,7 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
}
dev_info(&pdev->dev, "%dx%d %d-bit RGB FrameBuffer initialized\n",
LCD_X_RES, LCD_Y_RES, LCD_BPP);
LCD_X_RES, LCD_Y_RES, info->lcd_bpp);
return 0;
@ -705,7 +743,8 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
out8:
free_irq(info->irq, info);
out7:
bfin_lq035q1_free_ports();
bfin_lq035q1_free_ports(info->disp_info->ppi_mode ==
USE_RGB565_16_BIT_PPI);
out6:
fb_dealloc_cmap(&fbinfo->cmap);
out4:
@ -742,7 +781,8 @@ static int __devexit bfin_lq035q1_remove(struct platform_device *pdev)
fb_dealloc_cmap(&fbinfo->cmap);
bfin_lq035q1_free_ports();
bfin_lq035q1_free_ports(info->disp_info->ppi_mode ==
USE_RGB565_16_BIT_PPI);
platform_set_drvdata(pdev, NULL);
framebuffer_release(fbinfo);
@ -781,7 +821,7 @@ static int bfin_lq035q1_resume(struct device *dev)
bfin_lq035q1_config_dma(info);
bfin_lq035q1_config_ppi(info);
bfin_lq035q1_init_timers();
bfin_lq035q1_init_timers(info);
/* start dma */
enable_dma(CH_PPI);