Found with a network device in QEMU/KVM guest not working anymore.
Bisected to commit c13085e5
ACPICA: Resource Mgr: Prevent infinite loops in resource walks
That commit will check acpi_resource length strictly which causes
acpi_set_current_resources to return failure and IRQ for PCI
devices is not set properly.
Set length for all those TYPE_END_TAG acpi_resources.
[rjw: Changelog]
Bisected-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Devices on the Intel Lynxpoint Low Power Subsystem (LPSS) have
registers providing access to LTR (Latency Tolerance Reporting)
functionality that allows software to monitor and possibly influence
the aggressiveness of the platform's active-state power management.
For each LPSS device, there are two modes of operation related to LTR,
the auto mode and the software mode. In the auto mode the LTR is
set up by the platform firmware and managed by hardware. Software
can only read the LTR register values to monitor the platform's
behavior. In the software mode it is possible to use LTR to control
the extent to which the platform will use its built-in power
management features.
This changeset adds support for reading the LPSS devices' LTR
registers and exposing their values to user space for monitoring and
diagnostics purposes. It re-uses the MMIO mappings created to access
the LPSS devices' clock registers for reading the values of the LTR
registers and exposes them to user space through sysfs device
attributes. Namely, a new atrribute group, lpss_ltr, is created for
each LPSS device. It contains three new attributes: ltr_mode,
auto_ltr, sw_ltr. The value of the ltr_mode attribute reflects the
LTR mode being used at the moment (software vs auto) and the other
two contain the actual register values (raw) whose meaning depends
on the LTR mode. All of these attributes are read-only.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Devices on the Intel Lynxpoint Low Power Subsystem (LPSS) have some
common features that aren't shared with any other platform devices,
including the clock and LTR (Latency Tolerance Reporting) registers.
It is better to handle those features in common code than to bother
device drivers with doing that (I/O functionality-wise the LPSS
devices are generally compatible with other devices that don't
have those special registers and may be handled by the same drivers).
The clock registers of the LPSS devices are now taken care of by
the special clk-x86-lpss driver, but the MMIO mappings used for
accessing those registers can also be used for accessing the LTR
registers on those devices (LTR support for the Lynxpoint LPSS is
going to be added by a subsequent patch). Thus it is convenient
to add a special ACPI scan handler for the Lynxpoint LPSS devices
that will create the MMIO mappings for accessing the clock (and
LTR in the future) registers and will register the LPSS devices'
clocks, so the clk-x86-lpss driver will only need to take care of
the main Lynxpoint LPSS clock.
Introduce a special ACPI scan handler for Intel Lynxpoint LPSS
devices as described above. This also reduces overhead related to
browsing the ACPI namespace in search of the LPSS devices before the
registration of their clocks, removes some LPSS-specific (and
somewhat ugly) code from acpi_platform.c and shrinks the overall code
size slightly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
The acpi_hotplug_profile_ktype object should be static, so make that
be the case.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Compile warnings and errors (one on x86, two on ARM)
* WARNING in xen-pciback
* Use the acpi_processor_get_performance_info instead of the 'register' version
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRP33uAAoJEFjIrFwIi8fJfxMIAJxK7jI7NghJ87b8uk3IrkDl
VDsY5Re86XWE0HjsFDJXfWZCGumhpMb8hI1RJBavLDWQmk4THBqsKbx9rDgRZUJO
HepvhwD/RdK+nnjVmbAzJKuc7aOKQmeEW3Weysb32DW9C5Wg27LRrto/oVJIUsyj
4HrLcsZZqCiEYUZjGwrkrMC1yXx+2XvkX9mXq81hGj0xU4X1hMizwBAJvSE5lKca
r4LaCoZ0SuayHYHjEtxyjAcu39wnMdlCkdW9DUlqrjK7L3X29ifVvnb+aS951O5E
t57DCHY8WkI1BkaoHaAQqI7/Y1HpYbT8BALVmxXoIInI9lc8VLHZOs8/fVVDppQ=
=MxoB
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Compile warnings and errors (one on x86, two on ARM)
- WARNING in xen-pciback
- Use the acpi_processor_get_performance_info instead of the 'register'
version
* tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: remove redundant acpi/acpi_drivers.h include
xen: arm: mandate EABI and use generic atomic operations.
acpi: Export the acpi_processor_get_performance_info
xen/pciback: Don't disable a PCI device that is already disabled.
For the predefined names that return fully variable-length
packages, allow a zero-length package with no warning, since it
is technically a legal construct (and BIOS writers use it.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Flags the case where external control methods are unresolved,
meaning that the disassembler had no idea how many arguments to
parse for the method invocation.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes several possible problems with resource templates returned
by _CRS/_PRS/_DMA predefined names. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Used for the _STR and _MLS predefined names. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
New file, nsconvert.c, for return object conversion functions.
Created in preparation for new conversion functions forthcoming.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds the framework to allow object repairs very early in the
return object analysis. Enables repairs like string->unicode,
etc. Bob Moore, Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Descriptions to be compiled/used by the acpihelp utility only. Not
compiled for the kernel ACPICA code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Removal caused a regression on at least FreeBSD. This fix
reinstates the macros.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ensure that AcpiEnable and AcpiDisable work properly when the
hardware-reduced flag is set in the FADT.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the actual fixed event name to all messages for clarity.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since 20060317, the pointer to next object is the first element in
its common header. Remove bogus LinkOffset from ACPI_MEMORY_LIST
and directly use NextObject.
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This fixes a global and a pointer cast. Jung-uk Kim.
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add checks for zero-length resource descriptors in all code that
loops through a resource descriptor list. This prevents possible
infinite loops because the length is used to increment the traveral
pointer and detect the end-of-descriptor.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The git commit d5aaffa9dd
(cpufreq: handle cpufreq being disabled for all exported function)
tightens the cpufreq API by returning errors when disable_cpufreq()
had been called.
The problem we are hitting is that the module xen-acpi-processor which
uses the ACPI's functions: acpi_processor_register_performance,
acpi_processor_preregister_performance, and acpi_processor_notify_smm
fails at acpi_processor_register_performance with -22.
Note that earlier during bootup in arch/x86/xen/setup.c there is also
an call to cpufreq's API: disable_cpufreq().
This is b/c we want the Linux kernel to parse the ACPI data, but leave
the cpufreq decisions to the hypervisor.
In v3.9 all the checks that d5aaffa9dd
added are now hit and the calls to cpufreq_register_notifier will now
fail. This means that acpi_processor_ppc_init ends up printing:
"Warning: Processor Platform Limit not supported"
and the acpi_processor_ppc_status is not set.
The repercussions of that is that the call to
acpi_processor_register_performance fails right away at:
if (!(acpi_processor_ppc_status & PPC_REGISTERED))
and we don't progress any further on parsing and extracting the _P*
objects.
The only reason the Xen code called that function was b/c it was
exported and the only way to gather the P-states. But we can also
just make acpi_processor_get_performance_info be exported and not
use acpi_processor_register_performance. This patch does so.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Make the ACPI memory hotplug driver use struct acpi_scan_handler
for representing the object used to set up ACPI memory hotplug
functionality and to remove hotplug memory ranges and data
structures used by the driver before unregistering ACPI device
nodes representing memory. Register the new struct acpi_scan_handler
object with the help of acpi_scan_add_handler_with_hotplug() to allow
user space to manipulate the attributes of the memory hotplug
profile.
This results in a significant reduction of the drvier's code size
and removes some ACPI hotplug code duplication.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Make the ACPI container driver register its ACPI scan handler object
using acpi_scan_add_handler_with_hotplug() to allow user space to
manipulate its hotplug profile attributes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Introduce user space interface for manipulating hotplug profiles
associated with ACPI scan handlers.
The interface consists of sysfs directories under
/sys/firmware/acpi/hotplug/, one for each hotplug profile, containing
an attribute allowing user space to manipulate the enabled field of
the corresponding profile. Namely, switching the enabled attribute
from '0' to '1' will cause the common hotplug notify handler to be
installed for all ACPI namespace objects representing devices matching
the scan handler associated with the given hotplug profile (and
analogously for the converse switch).
Drivers willing to use the new user space interface should add their
ACPI scan handlers with the help of new funtion
acpi_scan_add_handler_with_hotplug().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Introduce new helper routine acpi_scan_handler_matching() for
checking if the given ACPI scan handler matches a given device ID
and rework acpi_scan_match_handler() to use the new routine (that
routine will also be useful for other purposes in the future).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Switch the ACPI container driver to using common device hotplug code
introduced previously. This reduces the driver down to a trivial
definition and registration of a struct acpi_scan_handler object.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Multiple drivers handling hotplug-capable ACPI device nodes install
notify handlers covering the same types of events in a very similar
way. Moreover, those handlers are installed in separate namespace
walks, although that really should be done during namespace scans
carried out by acpi_bus_scan(). This leads to substantial code
duplication, unnecessary overhead and behavior that is hard to
follow.
For this reason, introduce common code in drivers/acpi/scan.c for
handling hotplug-related notification and carrying out device
insertion and eject operations in a generic fashion, such that it
may be used by all of the relevant drivers in the future. To cover
the existing differences between those drivers introduce struct
acpi_hotplug_profile for representing collections of hotplug
settings associated with different ACPI scan handlers that can be
used by the drivers to make the common code reflect their current
behavior.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Introduce helper routine acpi_scan_match_handler() that will find the
ACPI scan handler matching a given device ID, if there is one, and
rework acpi_scan_attach_handler() to use the new routine (that
routine will also be useful for other purposes going forward).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
After PCI and USB have stopped using the .find_bridge() callback in
struct acpi_bus_type, the only remaining user of it is SATA, but SATA
only pretends to be a user, because it points that callback to a stub
always returning -ENODEV.
For this reason, drop the SATA's dummy .find_bridge() callback and
remove .find_bridge(), which is not used any more, from struct
acpi_bus_type entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
pr->id is u32 which never < 0, so remove the redundant pr->id < 0
check from acpi_processor_add().
[rjw: Changelog]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
kfree() on a NULL pointer is a no-op, so remove a redundant NULL
pointer check in map_mat_entry().
[rjw: Changelog]
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Got this dmesg log on an Acer Aspire 725.
[ 0.256351] ACPI: (supports S0ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568)
[ 0.256373] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568)
[ 0.256391] S3 S4 S5)
Avoid this interleaving error messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tim found:
WARNING: at arch/x86/kernel/smpboot.c:324 topology_sane.isra.2+0x6f/0x80()
Hardware name: S2600CP
sched: CPU #1's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
smpboot: Booting Node 1, Processors #1
Modules linked in:
Pid: 0, comm: swapper/1 Not tainted 3.9.0-0-generic #1
Call Trace:
set_cpu_sibling_map+0x279/0x449
start_secondary+0x11d/0x1e5
Don Morris reproduced on a HP z620 workstation, and bisected it to
commit e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock
is ready")
It turns out movable_map has some problems, and it breaks several things
1. numa_init is called several times, NOT just for srat. so those
nodes_clear(numa_nodes_parsed)
memset(&numa_meminfo, 0, sizeof(numa_meminfo))
can not be just removed. Need to consider sequence is: numaq, srat, amd, dummy.
and make fall back path working.
2. simply split acpi_numa_init to early_parse_srat.
a. that early_parse_srat is NOT called for ia64, so you break ia64.
b. for (i = 0; i < MAX_LOCAL_APIC; i++)
set_apicid_to_node(i, NUMA_NO_NODE)
still left in numa_init. So it will just clear result from early_parse_srat.
it should be moved before that....
c. it breaks ACPI_TABLE_OVERIDE...as the acpi table scan is moved
early before override from INITRD is settled.
3. that patch TITLE is total misleading, there is NO x86 in the title,
but it changes critical x86 code. It caused x86 guys did not
pay attention to find the problem early. Those patches really should
be routed via tip/x86/mm.
4. after that commit, following range can not use movable ram:
a. real_mode code.... well..funny, legacy Node0 [0,1M) could be hot-removed?
b. initrd... it will be freed after booting, so it could be on movable...
c. crashkernel for kdump...: looks like we can not put kdump kernel above 4G
anymore.
d. init_mem_mapping: can not put page table high anymore.
e. initmem_init: vmemmap can not be high local node anymore. That is
not good.
If node is hotplugable, the mem related range like page table and
vmemmap could be on the that node without problem and should be on that
node.
We have workaround patch that could fix some problems, but some can not
be fixed.
So just remove that offending commit and related ones including:
f7210e6c4a ("mm/memblock.c: use CONFIG_HAVE_MEMBLOCK_NODE_MAP to
protect movablecore_map in memblock_overlaps_region().")
01a178a94e ("acpi, memory-hotplug: support getting hotplug info from
SRAT")
27168d38fa ("acpi, memory-hotplug: extend movablemem_map ranges to
the end of node")
e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock is
ready")
fb06bc8e5f ("page_alloc: bootmem limit with movablecore_map")
42f47e27e7 ("page_alloc: make movablemem_map have higher priority")
6981ec3114 ("page_alloc: introduce zone_movable_limit[] to keep
movable limit for nodes")
34b71f1e04 ("page_alloc: add movable_memmap kernel parameter")
4d59a75125 ("x86: get pg_data_t's memory from other node")
Later we should have patches that will make sure kernel put page table
and vmemmap on local node ram instead of push them down to node0. Also
need to find way to put other kernel used ram to local node ram.
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Reported-by: Don Morris <don.morris@hp.com>
Bisected-by: Don Morris <don.morris@hp.com>
Tested-by: Don Morris <don.morris@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull EDAC fixes and ghes-edac from Mauro Carvalho Chehab:
"For:
- Some fixes at edac drivers (i7core_edac, sb_edac, i3200_edac);
- error injection support for i5100, when EDAC debug is enabled;
- fix edac when it is loaded builtin (early init for the subsystem);
- a "Firmware First" EDAC driver, allowing ghes to report errors via
EDAC (ghes-edac).
With regards to ghes-edac, this fixes a longstanding BZ at Red Hat
that happens with Nehalem and Sandy Bridge CPUs: when both GHES and
i7core_edac or sb_edac are running, the error reports are
unpredictable, as both BIOS and OS race to access the registers. With
ghes-edac, the EDAC core will refuse to register any other concurrent
memory error driver.
This patchset moves the ghes struct definitions to a separate header
file (include/acpi/ghes.h) and adds 3 hooks at apei/ghes.c to
register/unregister and to report errors via ghes-edac. Those changes
were acked by ghes driver maintainer (Huang)."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (30 commits)
i5100_edac: convert to use simple_open()
ghes_edac: fix to use list_for_each_entry_safe() when delete list items
ghes_edac: Fix RAS tracing
ghes_edac: Make it compliant with UEFI spec 2.3.1
ghes_edac: Improve driver's printk messages
ghes_edac: Don't credit the same memory dimm twice
ghes_edac: do a better job of filling EDAC DIMM info
ghes_edac: add support for reporting errors via EDAC
ghes_edac: Register at EDAC core the BIOS report
ghes: add the needed hooks for EDAC error report
ghes: move structures/enum to a header file
edac: add support for error type "Info"
edac: add support for raw error reports
edac: reduce stack pressure by using a pre-allocated buffer
edac: lock module owner to avoid error report conflicts
edac: remove proc_name from mci structure
edac: add a new memory layer type
edac: initialize the core earlier
edac: better report error conditions in debug mode
i5100_edac: Remove two checkpatch warnings
...
Pull more x86 fixes from Peter Anvin:
"Additional x86 fixes. Three of these patches are pure documentation,
two are pretty trivial; the remaining one fixes boot problems on some
non-BIOS machines."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure we can boot in the case the BDA contains pure garbage
x86, efi: Mark disable_runtime as __initdata
x86, doc: Fix incorrect comment about 64-bit code segment descriptors
doc, kernel-parameters: Document 'console=hvc<n>'
doc, xen: Mention 'earlyprintk=xen' in the documentation.
ACPI: Overriding ACPI tables via initrd only works with an initrd and on X86
- Fixes for blackfin and microblaze build problems introduced by the
removal of global pm_idle. From Lars-Peter Clausen.
- OPP core build fix from Shawn Guo.
- Error condition check fix for the new imx6q-cpufreq driver from
Wei Yongjun.
- Fix for an AER driver crash related to the lack of APEI
initialization for acpi=off. From Rafael J. Wysocki.
- Fix for a USB breakage on Thinkpad T430 related to ACPI power
resources and PCI wakeup from Rafael J. Wysocki.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=FCbx
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-fixes-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Fixes for blackfin and microblaze build problems introduced by the
removal of global pm_idle. From Lars-Peter Clausen.
- OPP core build fix from Shawn Guo.
- Error condition check fix for the new imx6q-cpufreq driver from Wei
Yongjun.
- Fix for an AER driver crash related to the lack of APEI
initialization for acpi=off. From Rafael J Wysocki.
- Fix for a USB breakage on Thinkpad T430 related to ACPI power
resources and PCI wakeup from Rafael J. Wysocki.
* tag 'pm+acpi-fixes-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Take unusual configurations of power resources into account
imx6q-cpufreq: fix return value check in imx6q_cpufreq_probe()
PM / OPP: fix condition for empty of_init_opp_table()
ACPI / APEI: Fix crash in apei_hest_parse() for acpi=off
microblaze idle: Fix compile error
blackfin idle: Fix compile error
Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ER3b
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
In order to allow reporting errors via EDAC, add hooks for:
1) register an EDAC driver;
2) unregister an EDAC driver;
3) report errors via EDAC.
As the EDAC driver will need to access the ghes structure, adds it
as one of the parameters for ghes_do_proc.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reflect this dependency in Kconfig, to prevent build failures.
Shorten the config description as suggested by Borislav Petkov.
Finding a suitable memory area to store the modified table(s) has been
taken over from arch/x86/kernel/setup.c and makes use of max_low_pfn_mapped:
memblock_find_in_range(0, max_low_pfn_mapped,...)
This one is X86 specific. It may not be hard to extend this functionality
for other ACPI aware architectures if there is need for.
For now make this feature only available for X86 to avoid build failures on
IA64, compare with:
https://bugzilla.kernel.org/show_bug.cgi?id=54091
Signed-off-by: Thomas Renninger <trenn@suse.de>
Link: http://lkml.kernel.org/r/1361538742-67599-3-git-send-email-trenn@suse.de
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
On linux, the pages used by kernel could not be migrated. As a result,
if a memory range is used by kernel, it cannot be hot-removed. So if we
want to hot-remove memory, we should prevent kernel from using it.
The way now used to prevent this is specify a memory range by
movablemem_map boot option and set it as ZONE_MOVABLE.
But when the system is booting, memblock will allocate memory, and
reserve the memory for kernel. And before we parse SRAT, and know the
node memory ranges, memblock is working. And it may allocate memory in
ranges to be set as ZONE_MOVABLE. This memory can be used by kernel,
and never be freed.
So, let's parse SRAT before memblock is called first. And it is early
enough.
The first call of memblock_find_in_range_node() is in:
setup_arch()
|-->setup_real_mode()
so, this patch add a function early_parse_srat() to parse SRAT, and call
it before setup_real_mode() is called.
NOTE:
1) early_parse_srat() is called before numa_init(), and has initialized
numa_meminfo. So DO NOT clear numa_nodes_parsed in numa_init() and DO
NOT zero numa_meminfo in numa_init(), otherwise we will lose memory
numa info.
2) I don't know why using count of memory affinities parsed from SRAT
as a return value in original acpi_numa_init(). So I add a static
variable srat_mem_cnt to remember this count and use it as the return
value of the new acpi_numa_init()
[mhocko@suse.cz: parse SRAT before memblock is ready fix]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The node will be offlined when all memory/cpu on the node is hotremoved.
So we should try offline the node when hotremoving a cpu on the node.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new function try_offline_node() to remove sysfs file of node
when all memory sections of this node are removed. If some memory
sections of this node are not removed, this function does nothing.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d2e5f0c (ACPI / PCI: Rework the setup and cleanup of device
wakeup) moved the initial disabling of system wakeup for PCI devices
into a place where it can actually work and that exposed a hidden old
issue with crap^Wunusual system designs where the same power
resources are used for both wakeup power and device power control at
run time.
Namely, say there is one power resource such that the ACPI power
state D0 of a PCI device depends on that power resource (i.e. the
device is in D0 when that power resource is "on") and it is used
as a wakeup power resource for the same device. Then, calling
acpi_pci_sleep_wake(pci_dev, false) for the device in question will
cause the reference counter of that power resource to drop to 0,
which in turn will cause it to be turned off. As a result, the
device will go into D3cold at that point, although it should have
stayed in D0.
As it turns out, that happens to USB controllers on some laptops
and USB becomes unusable on those machines as a result, which is
a major regression from v3.8.
To fix this problem, (1) increment the reference counters of wakup
power resources during their initialization if they are "on"
initially, (2) prevent acpi_disable_wakeup_device_power() from
decrementing the reference counters of wakeup power resources that
were not enabled for wakeup power previously, and (3) prevent
acpi_enable_wakeup_device_power() from incrementing the reference
counters of wakeup power resources that already are enabled for
wakeup power.
In addition to that, if it is impossible to determine the initial
states of wakeup power resources, avoid enabling wakeup for devices
whose wakeup power depends on those power resources.
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Tested-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit 92ef2a2 (ACPI: Change the ordering of PCI root bridge
driver registrarion), acpi_hest_init() is never called for acpi=off
(acpi_disabled), so hest_disable is not set, but hest_tab is NULL,
which causes apei_hest_parse() to crash when it is called from
aer_acpi_firmware_first().
Fix that by making apei_hest_parse() check if hest_tab is not NULL
in addition to checking hest_disable. Also remove the now useless
acpi_disabled check from apei_hest_parse().
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
As a ghes_edac driver will need to access ghes structures, in order
to properly handle the errors, move those structures to a separate
header file. No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from
Rafael J. Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng
with contributions from Aaron Lu, Chao Guan, Jesper Juhl, and
Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri
with contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from
Dirk Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King,
Davidlohr Bueso, Joseph Salisbury, Kees Cook, Li Fei,
Nishanth Menon, ShuoX Liu, Srinivas Pandruvada, Tejun Heo,
Thomas Renninger, and Yasuaki Ishimatsu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=wijn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from Rafael
J Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng with
contributions from Aaron Lu, Chao Guan, Jesper Juhl, and Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri with
contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from Dirk
Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King, Davidlohr Bueso,
Joseph Salisbury, Kees Cook, Li Fei, Nishanth Menon, ShuoX Liu,
Srinivas Pandruvada, Tejun Heo, Thomas Renninger, and Yasuaki
Ishimatsu.
* tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (267 commits)
PM idle: remove global declaration of pm_idle
unicore32 idle: delete stray pm_idle comment
openrisc idle: delete pm_idle
mn10300 idle: delete pm_idle
microblaze idle: delete pm_idle
m32r idle: delete pm_idle, and other dead idle code
ia64 idle: delete pm_idle
cris idle: delete idle and pm_idle
ARM64 idle: delete pm_idle
ARM idle: delete pm_idle
blackfin idle: delete pm_idle
sparc idle: rename pm_idle to sparc_idle
sh idle: rename global pm_idle to static sh_idle
x86 idle: rename global pm_idle to static x86_idle
APM idle: register apm_cpu_idle via cpuidle
cpufreq / intel_pstate: Add kernel command line option disable intel_pstate.
cpufreq / intel_pstate: Change to disallow module build
tools/power turbostat: display SMI count by default
intel_idle: export both C1 and C1E
ACPI / hotplug: Fix concurrency issues and memory leaks
...
Pull perf changes from Ingo Molnar:
"There are lots of improvements, the biggest changes are:
Main kernel side changes:
- Improve uprobes performance by adding 'pre-filtering' support, by
Oleg Nesterov.
- Make some POWER7 events available in sysfs, equivalent to what was
done on x86, from Sukadev Bhattiprolu.
- tracing updates by Steve Rostedt - mostly misc fixes and smaller
improvements.
- Use perf/event tracing to report PCI Express advanced errors, by
Tony Luck.
- Enable northbridge performance counters on AMD family 15h, by Jacob
Shin.
- This tracing commit:
tracing: Remove the extra 4 bytes of padding in events
changes the ABI. All involved parties (PowerTop in particular)
seem to agree that it's safe to do now with the introduction of
libtraceevent, but the devil is in the details ...
Main tooling side changes:
- Add 'event group view', from Namyung Kim:
To use it, 'perf record' should group events when recording. And
then perf report parses the saved group relation from file header
and prints them together if --group option is provided. You can
use the 'perf evlist' command to see event group information:
$ perf record -e '{ref-cycles,cycles}' noploop 1
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.385 MB perf.data (~16807 samples) ]
$ perf evlist --group
{ref-cycles,cycles}
With this example, default perf report will show you each event
separately.
You can use --group option to enable event group view:
$ perf report --group
...
# group: {ref-cycles,cycles}
# ========
# Samples: 7K of event 'anon group { ref-cycles, cycles }'
# Event count (approx.): 6876107743
#
# Overhead Command Shared Object Symbol
# ................ ....... ................. ..........................
99.84% 99.76% noploop noploop [.] main
0.07% 0.00% noploop ld-2.15.so [.] strcmp
0.03% 0.00% noploop [kernel.kallsyms] [k] timerqueue_del
0.03% 0.03% noploop [kernel.kallsyms] [k] sched_clock_cpu
0.02% 0.00% noploop [kernel.kallsyms] [k] account_user_time
0.01% 0.00% noploop [kernel.kallsyms] [k] __alloc_pages_nodemask
0.00% 0.00% noploop [kernel.kallsyms] [k] native_write_msr_safe
0.00% 0.11% noploop [kernel.kallsyms] [k] _raw_spin_lock
0.00% 0.06% noploop [kernel.kallsyms] [k] find_get_page
0.00% 0.02% noploop [kernel.kallsyms] [k] rcu_check_callbacks
0.00% 0.02% noploop [kernel.kallsyms] [k] __current_kernel_time
As you can see the Overhead column now contains both of ref-cycles
and cycles and header line shows group information also - 'anon
group { ref-cycles, cycles }'. The output is sorted by period of
group leader first.
- Initial GTK+ annotate browser, from Namhyung Kim.
- Add option for runtime switching perf data file in perf report,
just press 's' and a menu with the valid files found in the current
directory will be presented, from Feng Tang.
- Add support to display whole group data for raw columns, from Jiri
Olsa.
- Add per processor socket count aggregation in perf stat, from
Stephane Eranian.
- Add interval printing in 'perf stat', from Stephane Eranian.
- 'perf test' improvements
- Add support for wildcards in tracepoint system name, from Jiri
Olsa.
- Add anonymous huge page recognition, from Joshua Zhu.
- perf build-id cache now can show DSOs present in a perf.data file
that are not in the cache, to integrate with build-id servers being
put in place by organizations such as Fedora.
- perf top now shares more of the evsel config/creation routines with
'record', paving the way for further integration like 'top'
snapshots, etc.
- perf top now supports DWARF callchains.
- Fix mmap limitations on 32-bit, fix from David Miller.
- 'perf bench numa mem' NUMA performance measurement suite
- ... and lots of fixes, performance improvements, cleanups and other
improvements I failed to list - see the shortlog and git log for
details."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (270 commits)
perf/x86/amd: Enable northbridge performance counters on AMD family 15h
perf/hwbp: Fix cleanup in case of kzalloc failure
perf tools: Fix build with bison 2.3 and older.
perf tools: Limit unwind support to x86 archs
perf annotate: Make it to be able to skip unannotatable symbols
perf gtk/annotate: Fail early if it can't annotate
perf gtk/annotate: Show source lines with gray color
perf gtk/annotate: Support multiple event annotation
perf ui/gtk: Implement basic GTK2 annotation browser
perf annotate: Fix warning message on a missing vmlinux
perf buildid-cache: Add --update option
uprobes/perf: Avoid uprobe_apply() whenever possible
uprobes/perf: Teach trace_uprobe/perf code to use UPROBE_HANDLER_REMOVE
uprobes/perf: Teach trace_uprobe/perf code to pre-filter
uprobes/perf: Teach trace_uprobe/perf code to track the active perf_event's
uprobes: Introduce uprobe_apply()
perf: Introduce hw_perf_event->tp_target and ->tp_list
uprobes/perf: Always increment trace_uprobe->nhit
uprobes/tracing: Kill uprobe_trace_consumer, embed uprobe_consumer into trace_uprobe
uprobes/tracing: Introduce is_trace_uprobe_enabled()
...
Previously, we cached _PRT (PCI routing table, ACPI 5.0 sec 6.2.12)
contents and associated each _PRT entry with a PCI bus number. The bus
number association means dependencies on PCI device enumeration and bus
number assignment, as well as on the PCI/ACPI binding process.
After 4f535093cf ("PCI: Put pci_dev in device tree as early as possible"),
these dependencies caused the IRQ issues reported by Peter:
pci 0000:00:1e.0: PCI bridge to [bus 09] (subtractive decode)
pci 0000:00:1e.0: can't derive routing for PCI INT A
snd_ctxfi 0000:09:02.0: PCI INT A: no GSI - using ISA IRQ 5
irq 18: nobody cared (try booting with the "irqpoll" option)
This patch removes _PRT caching. Instead, we evaluate _PRT as needed
in the pci_enable_device() path. This also removes the dependency on
PCI bus numbers: we can simply look at the _PRT associated with each
bridge as we walk upstream toward the root.
[bhelgaas: changelog]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53561
Reported-and-tested-by: Peter Hurley <peter@hurleysoftware.com>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As discussed in thread at https://patchwork.kernel.org/patch/1946851/,
there's no value in supporting CONFIG_ACPI_PCI_SLOT=m any more.
So change Kconfig and code to only support building pci_slot as
built-in driver.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* acpi-cleanup: (21 commits)
ACPI / hotplug: Fix concurrency issues and memory leaks
ACPI: Remove the use of CONFIG_ACPI_CONTAINER_MODULE
ACPI / scan: Full transition to D3cold in acpi_device_unregister()
ACPI / scan: Make acpi_bus_hot_remove_device() acquire the scan lock
ACPI: Drop the container.h header file
ACPI / Documentation: refer to correct file for acpi_platform_device_ids[] table
ACPI / scan: Make container driver use struct acpi_scan_handler
ACPI / scan: Remove useless #ifndef from acpi_eject_store()
ACPI: Unbind ACPI drv when probe failed
ACPI: sysfs eject support for ACPI scan handlers
ACPI / scan: Follow priorities of IDs when matching scan handlers
ACPI / PCI: pci_slot: replace printk(KERN_xxx) with pr_xxx()
ACPI / dock: Fix acpi_bus_get_device() check in drivers/acpi/dock.c
ACPI / scan: Clean up acpi_bus_get_parent()
ACPI / platform: Use struct acpi_scan_handler for creating devices
ACPI / PCI: Make PCI IRQ link driver use struct acpi_scan_handler
ACPI / PCI: Make PCI root driver use struct acpi_scan_handler
ACPI / scan: Introduce struct acpi_scan_handler
ACPI / scan: Make scanning of fixed devices follow the general scheme
ACPI: Drop device start operation that is not used
...
This changeset is aimed at fixing a few different but related
problems in the ACPI hotplug infrastructure.
First of all, since notify handlers may be run in parallel with
acpi_bus_scan(), acpi_bus_trim() and acpi_bus_hot_remove_device()
and some of them are installed for ACPI handles that have no struct
acpi_device objects attached (i.e. before those objects are created),
those notify handlers have to take acpi_scan_lock to prevent races
from taking place (e.g. a struct acpi_device is found to be present
for the given ACPI handle, but right after that it is removed by
acpi_bus_trim() running in parallel to the given notify handler).
Moreover, since some of them call acpi_bus_scan() and
acpi_bus_trim(), this leads to the conclusion that acpi_scan_lock
should be acquired by the callers of these two funtions rather by
these functions themselves.
For these reasons, make all notify handlers that can handle device
addition and eject events take acpi_scan_lock and remove the
acpi_scan_lock locking from acpi_bus_scan() and acpi_bus_trim().
Accordingly, update all of their users to make sure that they
are always called under acpi_scan_lock.
Furthermore, since eject operations are carried out asynchronously
with respect to the notify events that trigger them, with the help
of acpi_bus_hot_remove_device(), even if notify handlers take the
ACPI scan lock, it still is possible that, for example,
acpi_bus_trim() will run between acpi_bus_hot_remove_device() and
the notify handler that scheduled its execution and that
acpi_bus_trim() will remove the device node passed to
acpi_bus_hot_remove_device() for ejection. In that case, the struct
acpi_device object obtained by acpi_bus_hot_remove_device() will be
invalid and not-so-funny things will ensue. To protect agaist that,
make the users of acpi_bus_hot_remove_device() run get_device() on
ACPI device node objects that are about to be passed to it and make
acpi_bus_hot_remove_device() run put_device() on them and check if
their ACPI handles are not NULL (make acpi_device_unregister() clear
the device nodes' ACPI handles for that check to work).
Finally, observe that acpi_os_hotplug_execute() actually can fail,
in which case its caller ought to free memory allocated for the
context object to prevent leaks from happening. It also needs to
run put_device() on the device node that it ran get_device() on
previously in that case. Modify the code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
In order to drop reference counts of all power resources used by an
ACPI device node being removed, acpi_device_unregister() calls
acpi_power_transition(device, ACPI_STATE_D3_COLD), which effectively
transitions the device node into D3cold if it uses any power
resources. However, for some device nodes it may not be appropriate
to remove power from them entirely before putting them into D3hot
before. On the other hand, executing _PS3 for devices that don't
use power resources before removing them shouldn't really hurt.
In fact, that is done by acpi_bus_hot_remove_device(), but this is
not the right place to do it, because the bus trimming may have
caused power to be removed from the device node in question already
before.
For these reasons, make acpi_device_unregister() carry out full
power-off transition for all device nodes supporting that and remove
the direct evaluation of _PS3 from acpi_bus_hot_remove_device().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI scan lock has been introduced to prevent acpi_bus_scan()
and acpi_bus_trim() from running in parallel with each other for
overlapping ACPI namespace scopes. However, it is not sufficient
to do that, because if acpi_bus_scan() is run (for an overlapping
namespace scope) right after the acpi_bus_trim() in
acpi_bus_hot_remove_device(), the subsequent eject will remove
devices without removing the corresponding struct acpi_device
objects (and possibly companion "physical" device objects).
Therefore acpi_bus_hot_remove_device() has to acquire the scan
lock before carrying out the bus trimming and hold it through
the evaluation of _EJ0, so make that happen.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
The include/acpi/container.h only contains a definition of a
structure that is not used any more, so drop it entirely.
Similar change was proposed earlier by Toshi Kani.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Make the ACPI container driver use struct acpi_scan_handler for
representing the object used to initialize ACPI containers and remove
the ACPI driver structure used previously and the data structures
created by it, since in fact they were not used for any purpose.
This simplifies the code and reduces the kernel's memory footprint by
avoiding the registration of a struct device_driver object with the
driver core and creation of its sysfs directory which is unnecessary.
In addition to that, make the namespace walk callback used for
installing the notify handlers for ACPI containers more
straightforward.
This change includes fixes from Toshi Kani.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Since the FORCE_EJECT symbol is never defined, the
#ifndef FORCE_EJECT in acpi_eject_store() is always true, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
When acpi_device_install_notify_handler() failed in acpi_device_probe(),
it calls acpi_drv->ops.remove() and fails the probe. However, the ACPI
driver is left bound to the acpi_device. Fix it by clearing the driver
and driver_data fields.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changed sysfs eject, acpi_eject_store(), so that it doesn't return
error codes for devices nodes with ACPI scan handlers attached and
no ACPI drivers.
[rjw: Changelog]
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The IDs of ACPI device nodes stored in their pnp.ids member arrays
are sorted by decreasing priority (i.e. the highest-priority ID is
the first entry). This means that when matching scan handlers to
device nodes, the namespace scanning code should walk the list of
scan handlers for each device node ID instead of walking the list
of device node IDs for each handler (the latter causes the first
handler matching any of the device node IDs to be chosen, although
there may be another handler matching an ID of a higher priority
which should be preferred). Make the code follow this observation.
This change has been suggested and justified by Toshi Kani.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Trivial changes to replace printk(KERN_xxx) with pr_xxx().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-lpss:
ACPI / platform: create LPSS clocks if Lynxpoint devices are found during scan
clk: x86: add support for Lynxpoint LPSS clocks
x86: add support for Intel Low Power Subsystem
ACPI / platform: fix comment about the platform device name
ACPI: add support for CSRT table
* acpi-pm: (35 commits)
ACPI / PM: Handle missing _PSC in acpi_bus_update_power()
ACPI / PM: Do not power manage devices in unknown initial states
ACPI / PM: Fix acpi_bus_get_device() check in drivers/acpi/device_pm.c
ACPI / PM: Fix /proc/acpi/wakeup for devices w/o bus or parent
ACPI / PM: Fix consistency check for power resources during resume
ACPI / PM: Expose lists of device power resources to user space
sysfs: Functions for adding/removing symlinks to/from attribute groups
ACPI / PM: Expose current status of ACPI power resources
ACPI / PM: Expose power states of ACPI devices to user space
ACPI / scan: Prevent device add uevents from racing with user space
ACPI / PM: Fix device power state value after transitions to D3cold
ACPI / PM: Use string "D3cold" to represent ACPI_STATE_D3_COLD
ACPI / PM: Sanitize checks in acpi_power_on_resources()
ACPI / PM: Always evaluate _PSn after setting power resources
ACPI / PM: Introduce helper for executing _PSn methods
ACPI / PM: Make acpi_bus_init_power() more robust
ACPI / PM: Fix build for unusual combination of Kconfig options
ACPI / PM: remove leading whitespace from #ifdef
ACPI / PM: Consolidate suspend-specific and hibernate-specific code
ACPI / PM: Move device power management functions to device_pm.c
...
* acpica: (56 commits)
ACPICA: Update version to 20130117
ACPICA: Update predefined info table for _MLS method
ACPICA: Remove some extraneous newlines in ACPI_ERROR type calls
ACPICA: iASL/Disassembler: Add option to ignore NOOP opcodes/operators
ACPICA: AcpiGetSleepTypeData: Allow \_Sx to return either 1 or 2 integers
ACPICA: Update ACPICA copyrights to 2013
ACPICA: Update predefined info table
ACPICA: Cleanup table handler naming conflicts.
ACPICA: Source restructuring: split large files into 8 new files.
ACPICA: Cleanup PM_TIMER_FREQUENCY definition.
ACPICA: Cleanup ACPI_DEBUG_PRINT macros to fix potential build breakages.
ACPICA: Update version to 20121220.
ACPICA: Interpreter: Fix Store() when implicit conversion is not possible.
ACPICA: Resources: Split interrupt share/wake bits into two fields.
ACPICA: Resources: Support for ACPI 5 wake bit in ExtendedInterrupt descriptor.
ACPICA: Interpreter: Add warning if 64-bit constant appears in 32-bit table.
ACPICA: Update ACPICA initialization messages.
ACPICA: Namespace: Eliminate dot...dot output during initialization.
ACPICA: Resource manager: Add support for ACPI 5 wake bit in IRQ descriptor.
ACPICA: Fix possible memory leak in dispatcher error path.
...
* acpi-scan: (30 commits)
ACPI / scan: Fix acpi_bus_get_device() check in acpi_match_device()
ACPI / scan: Make namespace scanning and trimming mutually exclusive
ACPI / scan: Make it clear that acpi_bus_trim() cannot fail
ACPI / scan: Drop acpi_bus_add() and use acpi_bus_scan() instead
ACPI: update ej_event interface to take acpi_device
ACPI / scan: Add second pass to acpi_bus_trim()
ACPI / scan: Change the implementation of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_device_unregister()
ACPI: Remove the ops field from struct acpi_device
ACPI: remove unused acpi_op_bind and acpi_op_unbind
ACPI / scan: Fix check of device_attach() return value.
ACPI / scan: Treat power resources in a special way
ACPI: Remove unused struct acpi_pci_root.id member
ACPI: Drop ACPI device .bind() and .unbind() callbacks
ACPI / PCI: Move the _PRT setup and cleanup code to pci-acpi.c
ACPI / PCI: Rework the setup and cleanup of device wakeup
ACPI: Add .setup() and .cleanup() callbacks to struct acpi_bus_type
ACPI: Make acpi_bus_scan() and acpi_bus_add() take only one argument
ACPI: Replace ACPI device add_type field with a match_driver flag
...
mwait_idle() is a C1-only idle loop intended to be more efficient
than HLT, starting on Pentium-4 HT-enabled processors.
But mwait_idle() has been replaced by the more general
mwait_idle_with_hints(), which handles both C1 and deeper C-states.
ACPI processor_idle and intel_idle use only mwait_idle_with_hints(),
and no longer use mwait_idle().
Here we simplify the x86 native idle code by removing mwait_idle(),
and the "idle=mwait" bootparam used to invoke it.
Since Linux 3.0 there has been a boot-time warning when "idle=mwait"
was invoked saying it would be removed in 2012. This removal
was also noted in the (now removed:-) feature-removal-schedule.txt.
After this change, kernels configured with
(CONFIG_ACPI=n && CONFIG_INTEL_IDLE=n) when run on hardware
that supports MWAIT will simply use HLT. If MWAIT is desired
on those systems, cpuidle and the cpuidle drivers above
can be enabled.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Enable ACPI SCI during suspend so that SCI can be used
as wake events for PM_SUSPEND_FREEZE.
For S3/S4 transition,
We disable all GPEs in suspend_ops->prepare_late() to
fix a problem that GPEs may trigger SCI before
arch_suspend_disable_irqs() is run.
So it is safe to leave the SCI enabled until
arch_suspend_irq_disable() is run.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Len Brown sent a patch to remove this field in the intel_idle driver.
The other user of this field is the davinci cpuidle driver and a
patch has been sent to remove the usage of it.
This patch removes the last user of this field.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The cpuidle_device is retrieved in the function by using directly
the global variable. But the caller of this function already have
this device and it can be passed as a parameter. That is one small
step to encapsulate the code more.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The different definitions are not used anywhere in the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a quirk to allow the Sony VGN-FW41E_H to suspend/resume
properly.
References: http://bugs.launchpad.net/bugs/1113547
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: All <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If _PS0 is defined for an ACPI device node, but _PSC isn't and
the device node doesn't use power resources for power management,
acpi_bus_update_power() will fail to update the power state of it,
because acpi_device_get_power() returns ACPI_STATE_UNKNOWN in that
case.
To handle that situation make acpi_bus_update_power() follow
acpi_bus_init_power() and try to force the given device node into
power state D0.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_bus_get_device() returns int not acpi_status.
The patch change not to apply ACPI_SUCCESS() to the return value of
acpi_bus_get_device().
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In general, for ACPI device power management to work, the initial
power states of devices must be known (otherwise, we wouldn't be able
to keep track of power resources, for example). Hence, if it is
impossible to determine the initial ACPI power states of some
devices, they can't be regarded as power-manageable using ACPI.
For this reason, modify acpi_bus_get_power_flags() to clear the
power_manageable flag if acpi_bus_init_power() fails and add some
extra fallback code to acpi_bus_init_power() to cover broken
BIOSes that provide _PS0/_PS3 without _PSC for some devices.
Verified to work on my HP nx6325 that has this problem.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
acpi_bus_get_device() returns int not acpi_status.
The patch change not to apply ACPI_FAILURE() to the return value of
acpi_bus_get_device().
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make acpi_bus_get_parent() more straightforward and remove an
unnecessary local variable ret from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since acpi_bus_get_device() returns int and not acpi_status, change
acpi_match_device() so that it doesn't apply ACPI_FAILURE() to the
return value of acpi_bus_get_device().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently, the ACPI namespace scanning code creates platform device
objects for ACPI device nodes whose IDs match the contents of the
acpi_platform_device_ids[] table. However, this adds a superfluous
special case into acpi_bus_device_attach() and makes it more
difficult to follow than it has to be. It also will make it more
difficult to implement removal code for those platform device objects
in the future.
For the above reasons, introduce a struct acpi_scan_handler object
for creating platform devices and move the code related to that from
acpi_bus_device_attach() to the .attach() callback of that object.
Also move the acpi_platform_device_ids[] table to acpi_platform.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make the ACPI PCI IRQ link driver use struct acpi_scan_handler
for representing the object used to set up ACPI interrupt links and
to remove data structures used for this purpose before unregistering
the corresponding ACPI device nodes.
This simplifies the code slightly and reduces the kernel's memory
footprint by avoiding the registration of a struct device_driver
object with the driver core and creation of its sysfs directory
which is unnecessary.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Make the ACPI PCI root bridge driver use struct acpi_scan_handler
for representing the object used to enumerate the PCI busses under
PCI host bridges found in the ACPI namespace (and to tear down data
structures representing the bus and devices on it before
unregistering the host bridges' ACPI device nodes).
This simplifies the code slightly and reduces the kernel's memory
footprint by avoiding the registration of a struct device_driver
object with the driver core and creation of its sysfs directory
which is unnecessary.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Introduce struct acpi_scan_handler for representing objects that
will do configuration tasks depending on ACPI device nodes'
hardware IDs (HIDs).
Currently, those tasks are done either directly by the ACPI namespace
scanning code or by ACPI device drivers designed specifically for
this purpose. None of the above is desirable, however, because
doing that directly in the namespace scanning code makes that code
overly complicated and difficult to follow and doing that in
"special" device drivers leads to a great deal of confusion about
their role and to confusing interactions with the driver core (for
example, sysfs directories are created for those drivers, but they
are completely unnecessary and only increase the kernel's memory
footprint in vain).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Make acpi_bus_scan_fixed() use device_attach() directly to attach
drivers, if any, to the fixed devices in analogy with how
acpi_bus_scan() works, which allows the last argument of
acpi_add_single_object() to be dropped and the manipulation of the
flags.match_driver bit to be moved to acpi_init_device_object()
and acpi_device_add_finalize().
After these changes all of the functions for the initialization
and registration of struct acpi_device objects work in the same
way for all of them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Fix /proc/acpi/wakeup for devices without bus or parent
This patch fixes printing the wakeup status for devices without a bus
or parent, such as laptop lid switches and sleep buttons. These devices
have an empty physical_node_list, because acpi_bind_one is never run
for them.
[rjw: White space and coding style.]
Signed-off-by: Andreas Fleig <andreasfleig@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no guarantee that acpi_bus_scan() and acpi_bus_trim() will
not be run in parallel for the same scope of the ACPI namespace,
which may lead to a great deal of confusion, so introduce a new mutex
to prevent that from happening.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
* pci/yinghai-root-bus-hotplug:
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
PCI/ACPI: Print info if host bridge notify handler installation fails
PCI: acpiphp: Move host bridge hotplug to pci_root.c
PCI/ACPI: acpiphp: Rename alloc_acpiphp_hp_work() to alloc_acpi_hp_work()
PCI: Make device create/destroy logic symmetric
PCI: Fix reference count leak in pci_dev_present()
PCI: Set pci_dev dev_node early so IOAPIC irq_descs are allocated locally
PCI: Add root bus children dev's res to fail list
PCI: acpiphp: Add is_hotplug_bridge detection
Conflicts:
drivers/pci/pci.h
* pci/acpi-scan2:
ACPI / scan: Drop acpi_bus_add() and use acpi_bus_scan() instead
ACPI: update ej_event interface to take acpi_device
ACPI / scan: Add second pass to acpi_bus_trim()
ACPI / scan: Change the implementation of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_device_unregister()
ACPI: Remove the ops field from struct acpi_device
ACPI: remove unused acpi_op_bind and acpi_op_unbind
ACPI / scan: Fix check of device_attach() return value.
The second argument of ACPI driver .remove() operation is only used
by the ACPI processor driver and the value passed to that driver
through it is always available from the given struct acpi_device
object's removal_type field. For this reason, the second ACPI driver
.remove() argument is in fact useless, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The comment describing the contents of the custom_method.c file is
obsolete, so update it.
[rjw: Subject and changelog]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As per documentation, "mode" sysfs interface should be able to
enable/disable thermal processing in the kernel, so that user space
is able to take more control.
Currently, ACPI thermal driver is not following this setting, so
modify it to match the interface documentation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI_EXCEPTION() already appends a newline, so there is no
need for the thermal trip point message to include one too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI_EXCEPTION() already appends a newline, so there is no
need for the invalid GPE message to include one too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI_ERROR() already appends a newline, so there is no
need for the error messages to include one too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Just as with the other memory affinity flags, report
non-volatile memory with ACPI debug.
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Observe that acpi_get_child() doesn't need to use the helper
struct acpi_find_child structure and change it to work without it.
Also, using acpi_get_object_info() to get the output of _ADR for the
given device is overkill, because that function does much more than
just evaluating _ADR (let alone the additional memory allocation
done by it).
Moreover, acpi_get_child() doesn't need to loop any more once it has
found a matching handle, so make it stop in that case. To prevent
the results from changing, make it use do_acpi_find_child() as
a post-order callback.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since acpi_bus_trim() cannot fail, change its definition to a void
function, so that its callers don't check the return value in vain
and update the callers.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
acpi_install_notify_handler() could fail. So check the exit status
and give a better debug info.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpiphp driver is confusing because it contains partial support for PCI
host bridge hotplug as well as support for hotplug of PCI devices.
This patch moves the host bridge hot-add support to pci_root.c and adds
hot-remove support in pci_root.c.
How to test it: if sci_emu patch is applied, find out root bus number to
ACPI root name mapping from dmesg or /sys. To remove root bus:
echo "\_SB.PCIB 3" > /sys/kernel/debug/acpi/sci_notify
To add back root bus:
echo "\_SB.PCIB 1" > /sys/kernel/debug/acpi/sci_notify
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Will need to use it for PCI root bridge hotplug support, so rename
*acpiphp* to *acpi* and move to osc.c. Also make kacpi_hotplug_wq static
after that.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
During system resume we check if there are power resources that have
been turned off by the BIOS, but our reference counters for them
are nonzero (they need to be turned on then). It turns out, however,
that we also need to check the opposite, i.e. if there are power
resources that have been turned on by the BIOS, but our reference
counters for them are zero (which means that no devices are going
to need them any time soon) and we should turn them off.
Make the power resources resume code do the additional check and
turn off the unused power resources as appropriate.
This change has been tested on HP nx6325.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since ACPI power resources are going to be used more extensively on
new hardware platforms, it is necessary to allow user space (powertop
in particular) to look at the lists of power resources corresponding
to different power states of devices for diagnostics and control
purposes.
For this reason, for each power state of an ACPI device node using
power resources create a special attribute group under the device
node's directory in sysfs containing links to sysfs directories
representing the power resources in that list. The names of the
new attribute groups are "power_resources_<state>", where <state>
is the state name i.e. "D0", "D1", "D2", or "D3hot".
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'acpi-scan' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Drop acpi_bus_add() and use acpi_bus_scan() instead
ACPI: update ej_event interface to take acpi_device
ACPI / scan: Add second pass to acpi_bus_trim()
ACPI / scan: Change the implementation of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_device_unregister()
ACPI: Remove the ops field from struct acpi_device
ACPI: remove unused acpi_op_bind and acpi_op_unbind
ACPI / scan: Fix check of device_attach() return value.
The second object for each sub-package of the _MLS method is
defined to be a unicode Buffer object. This fixes the predefined
table where this object was incorrectly defined as a String.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These macros/functions automatically insert a newline, so the
format string should not contain a newline at the end. (This allows
these functions to add information to the end of the output line.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Implemented for both the compiler and the disassembler. Often,
the NOOP opcode is used as padding for packages that are changed
dynamically by the BIOS. When disassembled, these NOOPs will
cause syntax errors. This option causes the disassembler to ignore
the NOOP opcode, and it also causes the compiler to ignore NOOP
statements as well.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Although the ACPI spec defines the \_Sx objects to return
a package containing one integer, most BIOS code returns two
integers and the previous code reflects that. However, we also
need to support BIOS code that actually implements to the ACPI
spec, and this change implements this.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Includes all source headers and signons for the various tools.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The predefined info table defines return types for specific control
methods. This patch updates predefined table as such enhancement has
already been done in ACPICA. This patch can also reduce source code
differences between Linux and ACPICA.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since ACPI power resources are going to be used more extensively on
new hardware platforms, it becomes necessary for user space (powertop
in particular) to observe some properties of those resources for
diagnostics purposes.
For this reason, expose the current status of each ACPI power
resource to user space via sysfs by adding a new resource_in_use
attribute to the sysfs directory representing the given power
resource.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it possible to retrieve the current power state of a device with
ACPI power management from user space via sysfs by adding two new
attributes, power_state and real_power_state, to the sysfs directory
associated with the struct acpi_device object representing the
device's ACPI node.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI core adds sysfs device files after the given devices have been
registered with device_register(), which is not appropriate, because
it may lead to race conditions with user space tools using those
files.
Fix the problem by delaying the KOBJ_ADD uevent for ACPI devices
until after all of the devices' sysfs files have been created.
This also fixes a use-after-free in acpi_device_unregister().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Lynxpoint LPSS peripheral drivers depend on LPSS clock tree being
created in order to function properly. The clock tree is exposed as a
platform driver that binds to a device named 'clk-lpt'.
To support this we modify the acpi_create_platform_device() to take one
additional parameter called flags. This is passed from
acpi_platform_device_ids[] array when acpi_create_platform_device() is
called.
We then introduce a new flag ACPI_PLATFORM_CLK which is used to tell
acpi_create_platform_device() to create the platform clocks as well.
Finally we set the ACPI_PLATFORM_CLK flags for all the Lynxpoint LPSS
devices and make sure that when this flag is set we create the
corresponding clock tree platform device.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To fix incorrect P-state frequencies which can happen on
some AMD systems f594065faf
"ACPI: Add fixups for AMD P-state figures"
introduced a quirk to obtain the correct values by reading
from AMD specific MSRs.
This did cause a regression when running a kernel using that
quirk under Xen which does (currently) not pass through MSR
reads to the HW. Instead the guest gets a 0 in return.
And this seems to cause a failure to initialize the ondemand
governour (hard to say for sure as all P-states appear to run
at the same frequency).
While this should also be fixed in the hypervisor (to allow
a guest to read that MSR), this patch is intended to work
around the issue in the meantime. In discussion it turned out
that indeed real HW/BIOSes may choose to not set the valid bit
and thus mark the P-state as invalid. So this could be considered
a fix for broken BIOSes that also works around the issue on Xen.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: 3.7+ <stable@vger.kernel.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a transition to the D3cold power state is requested,
acpi_device_set_power() first carries out a transition to D3hot and
then turns off the device's power resources. However, it fails to
update the device's power.state field appropriately and D3hot is
stored in it as a result.
Fix this, but make sure that the device's power state will be
D3hot if its power resources cannot be turned off in the final
step.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make acpi_power_state_string() return "D3cold" as the string
representation of ACPI power state D3cold instead of "D3" returned
currently, which is confusing.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After the only user of acpi_power_on_resources(),
acpi_bus_init_power(), has been changed to avoid calling it
for state equal to ACPI_STATE_D3_COLD, it doesn't have to special
case that state any more.
For this reason, modify the checks in acpi_power_on_resources()
so that it returns -EINVAL for ACPI_STATE_D3_COLD as it should.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI specitication (ACPI 5, Sections 7.2.8 - 7.2.11) requires
that the _PSn (n = 0..3) method, if present, be executed after the
power resources for the given device power state have been set
appropriately. However, acpi_device_set_power() does that only
if the new power state is going to be higher-power (lower-number)
than the power state the device is in already. Otherwise, the
ordering is reverse to protect against situations in which _PSn
might access device registers unavailable after configuring the
power resources for power state Dn (D3 meaning D3hot).
Such situations are very unlikely to happen, though, and _PSn may
actually be implemented with the assumption that power resources
have been configured for power state Dn in advance, so change the
code to follow the specification literally.
This change was previously porposed in a different form by Lv Zheng.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To reduce code duplication between acpi_device_set_power() and
acpi_bus_init_power(), introduce a new helper function for executing
ACPI devices' _PSn (n = 0..3) methods, acpi_dev_pm_explicit_set().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI specification requires the _PSC method to be present under
a device object if its power state cannot be inferred from the states
of power resources used by it (ACPI 5, Section 7.6.2). However, it
also requires that (for power states D0-D2 and D3hot) if the _PSn
(n = 0, 1, 2, 3) method is present under the device object, it also
must be executed after the power resources have been set
appropriately for the device to go into power state Dn (D3 means
D3hot in this case). Thus it is not clear from the specification
whether or not the _PSn method should be executed if the initial
configuraion of power resources used by the device indicates power
state Dn and the _PSC method is not present.
The current implementation of acpi_bus_init_power() is based on the
assumption that it should not be necessary to execute _PSn in the
above situation, but experience shows that in fact that assumption
need not be satisfied. For this reason, make acpi_bus_init_power()
always execute _PSn if the initial configuration of device power
resources indicates power state Dn.
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Len Brown <lenb@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We don't use _UID anymore, instead the name will be taken from the
corresponding ACPI device (adev). Fix the obsolete comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Core System Resources Table (CSRT) is a proprietary ACPI table that
contains resources for certain devices that are not found in the DSDT
table. Typically a shared DMA controller might be found here.
This patch adds support for this table. We go through all entries in the
table and make platform devices of them. The resources from the table are
passed with the platform device.
There is one special resource in the table and it is the DMA request line
base and number of request lines. This information might be needed by the
DMA controller driver as it needs to map the ACPI DMA request line number
to the actual request line understood by the hardware. This range is passed
as IORESOURCE_DMA resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is there probably due to an accident, get rid of it so that the format
is consistent across the file.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move some suspend-specific and hibernate-specific code from
acpi_sleep_init() into separate functions to get rid of explicit
#ifdefs in acpi_sleep_init(). Use pr_info() to start and pr_cont()
to continue printing the supported ACPI sleep states line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move ACPI device power management functions from drivers/acpi/bus.c
to drivers/acpi/device_pm.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The bit width check was introduced by 15afae60 (ACPI, APEI: Fix
incorrect APEI register bit width check and usage), and a fixup
for incorrect 32-bit width memory address was given by f712c71
(ACPI, APEI: Fixup common access width firmware bug). Now there
is a similar symptom:
[Firmware Bug]: APEI: Invalid bit width + offset in GAR [0x12345000/64/0/3/0]
Another bogus BIOS reports an incorrect 64-bit width in trigger table.
Thus, apply to a similar workaround for 64-bit width memory address.
Signed-off-by: Lans Zhang <jia.zhang@windriver.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The only difference between acpi_bus_scan() and acpi_bus_add() is the
invocation of acpi_update_all_gpes() in the latter which in fact is
unnecessary, because acpi_update_all_gpes() has already been called
by acpi_scan_init() and the way it is implemented guarantees the next
invocations of it to do nothing.
For this reason, drop acpi_bus_add() and make all its callers use
acpi_bus_scan() directly instead of it. Additionally, rearrange the
code in acpi_scan_init() slightly to improve the visibility of the
acpi_update_all_gpes() call in there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
acpi_processor_get_power_info() has to be called before
acpi_processor_setup_cpuidle_states() to have the latest
information available. This fixes the missing C-state information
after AC-->DC transition.
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function returning string representations of ACPI device power
states, state_string((), is now static, because it is only used
internally in drivers/acpi/bus.c. However, it will be used outside
of that file going forward, so rename it to
acpi_power_state_string(), add a kerneldoc comment to it and add its
header to acpi_bus.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function used for retrieving ACPI device power states,
__acpi_bus_get_power(), is now static, because it is only used
internally in drivers/acpi/bus.c. However, it will be used
outside of that file going forward, so rename it to
acpi_device_get_power(), in analogy with acpi_device_set_power(),
add a kerneldoc comment to it and add its header to acpi_bus.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During power transitions into D3cold from any shallower power states
we are supposed to transition the device into D3hot and remove power
from it afterward, but the current code in acpi_device_set_power()
doesn't work this way.
At the same time, though, we need to be careful enough to preserve
backwards compatibility for systems that don't distinguish between
D3hot and D3cold (e.g. designed before ACPI 4).
Modify acpi_device_set_power() so that it works in accordance with
the expectations in both cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The system level attribute of ACPI power resources is the lowest
system sleep level (S0, S2 etc.) in which the given resource can be
"on" (ACPI 5.0, Section 7.1). On the other hand, wakeup power
resources have to be "on" for devices depending on them to be able to
signal wakeup. Therefore devices cannot wake up the system from
sleep states higher than the minimum of the system level attributes
of their wakeup power resources.
Use the wakeup power resources' system level values to get the
deepest system sleep state (highest system sleep level) the given
device can wake up the system from.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some ACPI power resource initialization errors, like memory
allocation errors, are not taken into account appropriately in some
cases, which may lead to a device having an incomplete list of power
resources that one of its power states depends on, for one example.
Rework the power resource initialization and namespace scanning code
so that power resource initialization errors are treated more
seriously.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The lists of ACPI power resources are currently extracted in two
different ways, one for wakeup power resources and one for power
resources that device power states depend on. There is no reason
why it should be done differently in those two cases, so introduce
a common routine for extracting power resources lists from data
returned by AML, acpi_extract_power_resources(), and make the
namespace scanning code use it for both wakeup and device power
states power resources.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The local variables in acpi_bus_get_power_flags() need not be
initialized upfront, so change the code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To reduce indentation level and improve code readability, move the
initialization code related to device power states from
acpi_bus_get_power_flags() to a new routine,
acpi_bus_init_power_state().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI power resources have an order attribute that should be taken
into account when turning them on and off, but it is not used now.
Modify the power resources management code to preserve the
spec-compliant ordering of wakeup power resources.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI power resources have an order attribute that should be taken
into account when turning them on and off, but it is not used now.
Modify the power resources management code to preserve the
spec-compliant ordering of power resources that power states of
devices depend on (analogous changes will be done separately for
power resources used for wakeup).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI power resource objects have struct acpi_device components, but
they are only used for registering those resources in the device
hierarchy. In particular, power state information stored in them is
completely useless (amnong other things, because the power resources
"devices" are not power manageable), so there is no reason for the
power resources management code to keep it up to date.
Remove the code updating device power states of power resources from
drivers/acpi/power.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI power resources driver is not very useful, because the only
thing it really does is to restore the state of the power resources
that were "on" before system suspend or hibernation, but that may be
achieved in a different way.
Drop the ACPI power resources driver entirely and add
acpi_resume_power_resources() that will walk the list of all
registered power resources during system resume and turn on the ones
that were "on" before the preceding system suspend or hibernation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI power resources need to be treated in a special way by the
namespace scanning code, because they need to be ready to use as
soon as they have been discovered (even before registering ACPI
device nodes using them for power management).
For this reason, it doesn't make sense to separate the preparation
of struct acpi_device objects representing them in the device
hierarchy from the creation of struct acpi_power_resource objects
actually used for power resource manipulation. Accordingly, it
doesn't make sense to define non-empty .add() and .remove() callbacks
in the power resources "driver" (in fact, it is questionable whether
or not it is useful to register such a "driver" at all).
Rearrange the code in scan.c and power.c so that power resources are
initialized entirely by one routine, acpi_add_power_resource(), that
also prepares their struct acpi_device objects and registers them
with the driver core, telling it to use a special release routine,
acpi_release_power_resource(), for removing objects that represent
power resources from memory. Make the ACPI namespace scanning code
in scan.c always use acpi_add_power_resource() for preparing and
registering objects that represent power resources.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Simplify the code preparing struct acpi_device objects for
registration by removing useless code, moving different pieces of
code into the functions they belong to and making a couple of int
functions always returning 0 void.
This also fixes a possible memory leak in ACPI device registration
error code path by making acpi_device_register() detach data from
device->handle if device_register() fails and prepares the scanning
code for special-casing ACPI power resources (next patch).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 0090def6 (ACPI: Add interface to register/unregister device
to/from power resources) made it possible to indicate to the ACPI
core that if the given device depends on any power resources, then
it should be resumed as soon as all of the power resources required
by it to transition to the D0 power state have been turned on.
Unfortunately, however, this was a mistake, because all devices
depending on power resources should be treated this way (i.e. they
should be resumed when all power resources required by their D0
state have been turned on) and for the majority of those devices
the ACPI core can figure out by itself which (physical) devices
depend on what power resources.
For this reason, replace the code added by commit 0090def6 with a
new, much more straightforward, mechanism that will be used
internally by the ACPI core and remove all references to that code
from kernel subsystems using ACPI.
For the cases when there are (physical) devices that should be
resumed whenever a not directly related ACPI device node goes into
D0 as a result of power resources configuration changes, like in
the SATA case, add two new routines, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), allowing subsystems to manage
such dependencies. Convert the SATA subsystem to use the new
functions accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Should use acpi_device pointer directly instead of use handle and
get the device pointer again later.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make acpi_bus_trim() work in analogy with acpi_bus_scan() and carry
out two passes such that ACPI drivers will be detached from device
nodes being removed in the first pass and the device nodes themselves
will be removed in the second pass.
For this purpose split the driver unregistration out of
acpi_bus_remove() into a new routine, acpi_bus_device_detach(), that
will be executed by acpi_bus_trim() in the additional first pass as
a post-order callback.
This is necessary, because some ACPI drivers' .remove() routines
unregister struct device objects associated with the ACPI device
nodes being removed and that needs to happen while the ACPI
device nodes are still around (for example, in case they need to be
used for power management or similar things at that time).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
The current acpi_bus_trim() implementation is not really
straightforward and may be simplified significantly by using
acpi_walk_namespace() with acpi_bus_remove() as a post-order
callback.
Observe that acpi_bus_remove(), as called by acpi_bus_trim(), cannot
actually fail, because its first argument is guaranteed not to be
NULL thanks to the acpi_bus_get_device() check in acpi_bus_trim(),
so simply move the acpi_bus_get_device() check to acpi_bus_remove()
and use acpi_walk_namespace() to execute it for every device under
start->handle as a post-order callback. The, run it directly for
start->handle itself.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
All callers of acpi_bus_trim() pass 1 (true) as the second argument
of it, so remove that argument entirely and change acpi_bus_trim()
to always behave as though it were 1.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Drop the second argument of acpi_device_unregister(), type, which is
not used by that function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
The ACPI handles of PCI root bridges need to be known to
acpi_bind_one(), so that it can create the appropriate
"firmware_node" and "physical_node" files for them, but currently
the way it gets to know those handles is not exactly straightforward
(to put it lightly).
This is how it works, roughly:
1. acpi_bus_scan() finds the handle of a PCI root bridge,
creates a struct acpi_device object for it and passes that
object to acpi_pci_root_add().
2. acpi_pci_root_add() creates a struct acpi_pci_root object,
populates its "device" field with its argument's address
(device->handle is the ACPI handle found in step 1).
3. The struct acpi_pci_root object created in step 2 is passed
to pci_acpi_scan_root() and used to get resources that are
passed to pci_create_root_bus().
4. pci_create_root_bus() creates a struct pci_host_bridge object
and passes its "dev" member to device_register().
5. platform_notify(), which for systems with ACPI is set to
acpi_platform_notify(), is called.
So far, so good. Now it starts to be "interesting".
6. acpi_find_bridge_device() is used to find the ACPI handle of
the given device (which is the PCI root bridge) and executes
acpi_pci_find_root_bridge(), among other things, for the
given device object.
7. acpi_pci_find_root_bridge() uses the name (sic!) of the given
device object to extract the segment and bus numbers of the PCI
root bridge and passes them to acpi_get_pci_rootbridge_handle().
8. acpi_get_pci_rootbridge_handle() browses the list of ACPI PCI
root bridges and finds the one that matches the given segment
and bus numbers. Its handle is then used to initialize the
ACPI handle of the PCI root bridge's device object by
acpi_bind_one(). However, this is *exactly* the ACPI handle we
started with in step 1.
Needless to say, this is quite embarassing, but it may be avoided
thanks to commit f3fd0c8 (ACPI: Allow ACPI handles of devices to be
initialized in advance), which makes it possible to initialize the
ACPI handle of a device before passing it to device_register().
Accordingly, add a new __weak routine, pcibios_root_bridge_prepare(),
defaulting to an empty implementation that can be replaced by the
interested architecutres (x86 and ia64 at the moment) with functions
that will set the root bridge's ACPI handle before its dev member is
passed to device_register(). Make both x86 and ia64 provide such
implementations of pcibios_root_bridge_prepare() and remove
acpi_pci_find_root_bridge() and acpi_get_pci_rootbridge_handle() that
aren't necessary any more.
Included is a fix for breakage on systems with non-ACPI PCI host
bridges from Bjorn Helgaas.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If ACPI_GLUE_DEBUG is different from 0 (setting this requires a
manual change of glue.c), build breaks because of a leftover
reference to dev->acpi_handle in acpi_platform_notify(). Fix this
by using ACPI_HANDLE(dev) instead as appropriate.
[rjw: Subject and changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since device_attach() returns 1 on success (a driver has been bound
to the device), the check against its return value in
acpi_bus_device_attach() should modified to take that into accout.
Make it so.
[rjw: Subject and changelog.]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a cosmetic patch only. Comparison of the resulting binary showed
only line number differences.
This patch does not affect the generation of the Linux binary.
This patch decreases 44 lines of 20121114 divergence.diff.
There are naming conflicts between Linux and ACPICA on table handlers. This
patch cleans up this conflicts to reduce the source code diff between Linux
and ACPICA.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Created logical splits for eight new files. Improves modularity
and configurability.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* 'acpi-scan' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Treat power resources in a special way
ACPI: Remove unused struct acpi_pci_root.id member
ACPI: Drop ACPI device .bind() and .unbind() callbacks
ACPI / PCI: Move the _PRT setup and cleanup code to pci-acpi.c
ACPI / PCI: Rework the setup and cleanup of device wakeup
ACPI: Add .setup() and .cleanup() callbacks to struct acpi_bus_type
ACPI: Make acpi_bus_scan() and acpi_bus_add() take only one argument
ACPI: Replace ACPI device add_type field with a match_driver flag
ACPI: Drop the second argument of acpi_bus_scan()
ACPI: Remove the arguments of acpi_bus_add() that are not used
ACPI: Remove acpi_start_single_object() and acpi_bus_start()
ACPI / PCI: Fold acpi_pci_root_start() into acpi_pci_root_add()
ACPI: Change the ordering of acpi_bus_check_add()
ACPI: Replace struct acpi_bus_ops with enum type
ACPI: Reduce the usage of struct acpi_bus_ops
ACPI: Make acpi_bus_add() and acpi_bus_start() visibly different
ACPI: Change the ordering of PCI root bridge driver registrarion
ACPI: Separate adding ACPI device objects from probing ACPI drivers
Conflicts:
drivers/acpi/pci_root.c
This is a cosmetic patch only. Comparison of the resulting binary showed
only line number differences.
This patch does not affect the generation of the Linux binary.
This patch decreases 13 lines of 20121114 divergence.diff.
There is updates in ACPICA for PM_TIMER_FREQUENCY macro, this patch cleans
up the usage of this macro in Linux. This patch can also reduce the source
code diff between Linux and ACPICA.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For the cases such as a store of a string to an existing package
object, implement the store as a CopyObject().
This is a small departure from the ACPI specification which states
that the control method should be aborted in this case. However,
ASLTS suite depends on this behavior.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These two bits are merged at the external interface level for the
IRQ, Interrupt, and GpioInt resource descriptors. However, these
bits are logically independent and there is no need to keep them
merged internally. Therefore, this change splits the bits into
"sharable" and "wake capable" fields within the resource manager.
This simplifies drive code that needs to examine these bits.
Aaron Lu, Bob Moore.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support to both get and set the extended share flags for the
Interrupt() resource descriptor. Reported by Aaron Lu.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some ASL compilers allow 64-bit constants within a 32-bit table
(DSDT version == 1). When encountered, emit a warning that the
constant will be truncated to 32 bits. This is potentially a
serious problem in the ACPI table(s).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Clarify messages, indent if appropriate. Change a couple
appropriate messages to ACPI_INFO so they will appear even if
debug output is disabled.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This feature no longer serves any good purpose and also confuses any error
messages during ACPICA initialization.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support to both get and set the extended share flags for the
IRQ() resource descriptor. Reported by Aaron Lu.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On error, delete mutex object created during method mutex creation.
Reported by tim.gardner@canonical.com.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Also add acoutput.h to the nsdump.c file.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Moved the debug trace macros from acmacros.h into acoutput.h
where they belong.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Simplifies check for debug output enables.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These macros were implemented the same as return_VALUE and thus
they were not needed.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the functions that implement the macros, check if debug
is enabled up-front before the call to the lower debug print
function. This provides a small performance improvement.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move check for "debug enable" to before the actual call to the
debug print routine. Improves time of ASLTS by about 15%. Also,
remove "safe" exit macros since no complex expressions are ever
used in the return statements.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a missing cast for a namespace node pointer passed in from
an external interface. Reported Rafael Wysocki.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Constants for time manipulation, including constants for the 100
nanosecond timers. Chao Guan, Bob Moore, Lv Zheng.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some changes from lint.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Detect a request for the root node (a lone backslash) up front
before invoking a full namespace lookup.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Removed several small pathname functions to increase efficiency.
Essentially, they replace a function call with a single compare.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For the case where one of the input strings is too long,
change the returned exception code from AE_BAD_PARAMETER to
AE_AML_STRING_LIMIT.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Implements a new interface for walking resource lists that it at
a lower level than the existing AcpiWalkResources. (Method is
not executed.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No need for a goto to the bottom of the function, simply return
the status code immediately.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yinghai Lu
Rafael J. Wysocki
Linus Torvalds
Bob Moore
Lv Zheng
Jung-uk Kim
Konrad Rzeszutek Wilk
Chen Gang
Syam Sidhardhan
Joe Perches
Mauro Carvalho Chehab
Thomas Renninger
Tang Chen
Wen Congyang
Bjorn Helgaas
Len Brown
Jiang Liu
Toshi Kani
Jiang Liu
Zhang Rui
Daniel Lezcano
Joseph Salisbury
Yasuaki Ishimatsu
Matt Fleming
Andreas Fleig
Greg Kroah-Hartman
Srinivas Pandruvada
Colin Ian King
Davidlohr Bueso
Ingo Molnar
Mika Westerberg
Stefan Bader
Kees Cook
Rusty Russell
Lans Zhang
Thomas Schlichter
Aaron Lu
Tim Gardner