commit 97c3557c3e0413efb1f021f582d1459760e22727 upstream.
The gate clocks for the MFC sysmmus appear to be flipped, i.e.
GATE_IP_MFC[2] gates sysmmu_mfcl and GATE_IP_MFC[1] gates sysmmu_mfcr.
Fix this so that the MFC will start up.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2feed5aecf5f367b92bd6b6e92afe9e3de466907 upstream.
The sysreg (system register) generates control signals for various blocks
like disp1blk, i2c, mipi, usb etc. However, it gets disabled as an unused
clock at boot-up. This can lead to failures in operation of above blocks,
because they can not be configured properly if this clock is disabled.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fdd1b56be51b1ec4dbde5b213d649ac717442da upstream.
The SRC_MFC register offset was incorrect, which could cause have caused
wrong calculation of rate of sclk_mfc clock, that could in turn lead to
incorrect operation of MFC. This patch corrects it.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently 'pmu' clock is not handled by any of the drivers.
Also before the introduction of CCF, this clock was not defined,
hence was left enabled always.
When this clock is disabled, software reset register becomes
inaccessible and system reboot doesn't work.
Upon restoring the default behaviour, system reboot starts working.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The KDIV value is often listed as unsigned but it needs to be treated
as a 16-bit signed value when using it in calculations. Fix our rate
recalculation to do this correctly.
Before doing this, I tried setting EPLL on exynos5250 to:
rate, m, p, s, k = 80000000, 107, 2, 4, 43691
This rate is exactly from the table in the exynos5250 user manual.
I read this back as 80750003 with:
cat /sys/kernel/debug/clk/fin_pll/fout_epll/clk_rate
After this patch, it reads back as 80000003
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'mout_mpll' is added the list of parent clocks for 'mout_cpu'.
'mout_mpll' is an alias to the clock 'sclk_mpll'. Hence 'sclk_mpll'
should be added to the list of parent clocks.
This results in an error when cpufreq driver for EXYNOS5250 tries to
set 'mout_mpll' as a parent for 'mout_cpu'.
clk_set_parent: clk sclk_mpll can not be parent of clk mout_cpu
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
cpufreq driver for EXYNOS5250 is not a platform driver, hence we cannot
currently pass the clock names through a device tree node. Instead, we
need to make them available through a global alias.
cpufreq driver for EXYNOS5250 requires four clocks - 'armclk',
'mout_cpu', 'mout_mpll' and 'mout_apll'.
'armclk' has already been defined with an alias, 'mout_cpu', 'mout_mpll'
and 'mout_apll' are now defined with an alias.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently no driver *) handles the sysreg clock, with an assumption
that this clock is always left in its default state (enabled).
Before commit 6e6aac7590
ARM: EXYNOS: Migrate clock support to common clock framework
the sysreg clock was not even defined and hence wasn't handled
explicitly in the kernel.
To restore the previous behaviour disable masking the sysreg clock
off in the clock core by default.
*) Except the Exynos4x12 FIMC-IS driver, which will be modified
to not touch the sysreg clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series
in order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform,
but related to the other patches in this set and needed as a bug
fix for at least one board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FY7+
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM Exynos multiplatform changes from Arnd Bergmann:
"These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series in
order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform, but
related to the other patches in this set and needed as a bug fix for
at least one board."
* tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: dts: exynops4210: really add universal_c210 dts
ARM: dts: exynos4210: Add basic dts file for universal_c210 board
ARM: dts: exynos4: Add node for PWM device
ARM: SAMSUNG: Do not register legacy timer interrupts on Exynos
clocksource: samsung_pwm_timer: Work around rounding errors in clockevents core
clocksource: samsung_pwm_timer: Correct programming of clock events
clocksource: samsung_pwm_timer: Use proper clockevents max_delta
clocksource: samsung_pwm_timer: Add support for non-DT platforms
clocksource: samsung_pwm_timer: Drop unused samsung_pwm struct
clocksource: samsung_pwm_timer: Keep all driver data in a structure
clocksource: samsung_pwm_timer: Make PWM spinlock global
clocksource: samsung_pwm_timer: Let platforms select the driver
Documentation: Add device tree bindings for Samsung PWM timers
clocksource: add samsung pwm timer driver
irqchip: exynos: look up irq using irq_find_mapping
irqchip: exynos: pass irq_base from platform
irqchip: exynos: localize irq lookup for ATAGS
irqchip: exynos: allocate combiner_data dynamically
irqchip: exynos: pass max combiner number to combiner_init
ARM: exynos: add missing properties for combiner IRQs
...
commit 688f7d8c9f ("clk: exynos5250: Fix divider values for
sclk_mmc{0,1,2,3}") incorrectly sets the divider for sclk_mmc{0,1,2,3}
to fix the wrong clock value. Though this fixed issue with Arndale,
it created regressions for other boards like Snow.
On Exynos5250, sclk_mmc<n> is generated like below (as per the clock
names in drivers/clk/samsung/clk-exynos5250.c)
mout_group1_p ==> mout_mmc<n> ==>
div_mmc<n> ==> div_mmc_pre<n> => sclk_mmc<n>
Earlier div_mmc<n> was set as the parent for sclk_mmc<n>, hence
div_mmc_pre<n> was not getting referred in kernel code and depending
on its value set during preboot, sclk_mmc<n> value was different for
various boards.
Setting the correct clock generation path should fix the issues
reported in above referenced commit. The changes committed during the
earlier patch has also been reverted here.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The new common clock drivers for exynos are using compile
time constants and soc_is_exynos* macros to provide backwards
compatibility for pre-DT systems, which is not possible with
multiplatform kernels. This moves all the necessary
information back into platform code and removes the mach/*
header inclusions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@linaro.org>
In legacy setup, sclk_mmc{0,1,2,3} used PRE_RATIO bit-field (8-bit wide)
instead of RATIO bit-field (4-bit wide) for dividing clock rate.
With current common clock setup, we are using RATIO bit-field which
is creating FIFO read errors while accessing eMMC. Changing over to
use PRE_RATIO bit-field fixes this issue.
dwmmc_exynos 12200000.dwmmc0: data FIFO error (status=00008020)
mmcblk0: error -5 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
end_request: I/O error, dev mmcblk0, sector 1
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds clock indexes for ACLK_DIV0, ACLK_DIV1,
ACLK_400_MCUISP, ACLK_MCUISP_DIV0, ACLK_MCUISP_DIV1,
DIVACLK_400_MCUISP and DIVACLK_200 so these clocks are
available to the consumers (Exynos4x12 FIMC-IS subsystem).
While at it, indentation of the mux clocks table is
corrected.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixes the below compilation error during non-dt build.
drivers/clk/samsung/clk.c: In function 'samsung_clk_of_register_fixed_ext':
drivers/clk/samsung/clk.c:252:2: error: implicit declaration of function 'for_each_matching_node_and_match' [-Werror=implicit-function-declaration]
drivers/clk/samsung/clk.c:252:60: error: expected ';' before '{' token
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add gate clocks for fimd, mie, dsim, dp, mixer and hdmi.
Register it to common clock framework.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch extends suspend/resume support for SoC-specific registers to
handle differences in register sets on particular SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missing clock control registers to the list of registers
that should be saved across system suspend.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This register is present on all Exynos4 SoCs and so the prefix is
misleading.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This definition is specific for Exynos4210 (which has another location
than the same register on Exynos4x12 SoCs) and so needs appropriate
prefix.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds E4210 prefix to all registers related to LCD1 clock
domain, because they are present only on Exynos4210.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Current clock save list is shared for all Exynos4 SoCs, so it must
contain only registers present in all supported SoCs, because accessing
unavailable registers might have undefined effect.
This patch removes registers specific for particular SoCs from shared
save list, as they should be supported by separate SoC-specific lists.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are definitions of SRC_MASK_PERIL0 and SRC_MASK_PERIL1 registers,
but they are not used for clock definitions. This patch modifies related
clock definitions to use defined macros instead of numeric offsets.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds preprocessor definitions of EPLL and VPLL registers and
replaces all occurences of offsets of related registers with new
definitions.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missing mout_sata that is a parent of div_sata clock.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch adds missing clocks to TOP and ISP clock domains.
It also adds clock gates for ISP sub-blocks.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds clocks needed for G3D block present on Exynos 4 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds several gate and mux clocks related to camera and ISP
blocks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables clock lookup registration for mout_core clock used in
Exynos4210 cpufreq driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Unimplemented clock operations should be simply omitted instead of returning
error values.
This patch removes unimplemented PLL operations to fix problems caused
by returning error code in round_rate callback.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch exports clocks used by Exynos cpufreq drivers to allow lookup
using device tree. (Support to cpufreq drivers will be added in further
patches.)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sclk_dac and sclk_mixer clocks are not present on Exynos4x12.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This clock is used by PCM interface 0.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This clock is a parent of mout_spdif and sclk_pcm0.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missing output of mux MIPIHSI which is needed for
div_mipihsi clock.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Many clock muxes of Exynos 4x12 uses mout_mpll_user_* clocks instead of
sclk_mpll as one of their parents.
This patch moves such clocks from common array into SoC-specific arrays
and adjusts their parent lists respectively.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This clock must be exported to allow lookup using device tree.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The current code adds aliases, if necessary, directly when adding
the clock, limiting the number of possible aliases to one.
Some platforms need more than one alias, like the hsmmc pclocks on
s3c2416 which need a "hsmmc" and "mmc_busclk.0" alias for the s3c-
sdhci driver.
Therefore add the possibility to separately add clock aliases for
previously created clocks.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed to allow looking up previous created clocks when
adding separate aliases to them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The clock_init function checked for a dt node, returning immediately
for non-dt machines. This let to the suspend init never being reached
on those non-DT machines.
So fix this by moving the pm init code above the check.
Signed-off-by: Heiko Stueber <heiko@sntech.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On some Samsung platforms divider clocks only use specific divider
combinations like the armdiv on s3c2443 and s3c2416. For these
usecases the generic divider clock already provides the option of
providing a lookup table mapping register values to divider values.
Therefore add a new field to samsung_div_clock and if filled with a
table, use clk_register_divider_table instead of clk_register_divider
to register a divider clock
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5440 clocks are statically listed and registered using the
Samsung specific common clock helper functions.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5250 clocks are statically listed and registered using the
Samsung specific common clock helper functions. Both device tree based
clock lookup and clkdev based clock lookups are supported.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos4 clocks are statically listed and registered using the
Samsung specific common clock helper functions. Both device tree
based clock lookup and clkdev based clock lookups are supported.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are several types of pll clocks used in Samsung SoC's and these
pll clocks can be represented as Samsung specific pll clock types and
registered with the common clock framework. Add support for pll35xx,
pll36xx, pll45xx, pll46xx and pll2550x clock types and helper functions
to register them.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
All Samsung platforms include different types of clock including
fixed-rate, mux, divider and gate clock types. There are typically
hundreds of such clocks on each of the Samsung platforms. To enable
Samsung platforms to register these clocks using the common clock
framework, a bunch of utility functions are introduced here which
simplify the clock registration process. The clocks are usually
statically instantiated and registered with common clock framework.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andrew Bresticker
Abhilash Kesavan
Seung-Woo Kim
Tushar Behera
Doug Anderson
Sylwester Nawrocki
Linus Torvalds
Arnd Bergmann
Sachin Kamat
Leela Krishna Amudala
Tomasz Figa
Andrzej Hajda
Lukasz Majewski
Heiko Stuebner
Thomas Abraham