Update PCIe PHY register values base on PHY sequence.
Change-Id: Ieee7aa6f9904a3bd718ba2d21d525c803c1059dd
Signed-off-by: Tony Truong <truong@codeaurora.org>
PCIe Endpoints can be connected to PCIe Root Complex via PCIe
bridges. Add the support in PCIe bus driver to configure and
manage PCIe bridge.
Change-Id: I31c3d8bed3be5550be8b6b304533d35bbbf42932
Signed-off-by: Tony Truong <truong@codeaurora.org>
commit 67ebd8140dc8923c65451fa0f6a8eee003c4dcd3 upstream.
3448a19da4 "vgaarb: use bridges to control VGA routing where possible"
added the "flags & PCI_VGA_STATE_CHANGE_DECODES" condition to an existing
WARN_ON(), but used bitwise AND (&) instead of logical AND (&&), so the
condition is never true. Replace with logical AND.
Found by Coverity (CID 142811).
Fixes: 3448a19da4 "vgaarb: use bridges to control VGA routing where possible"
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c82126a94e69bbbac586f0249e7ef11e681246c upstream.
After a CPU upgrade while keeping the same mainboard, we faced "spurious
interrupt" problems again.
It turned out that the new CPU also featured a new GPU with a different PCI
ID.
Add this PCI ID to the quirk table. Probably all other Intel GPU PCI IDs
are affected, too, but I don't want to add them without a test system.
See f67fd55fa9 ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") for some history.
[bhelgaas: add f67fd55fa9 reference, stable tag]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust PCIe address space in HW setting based on PCIe address
range of a Root Complex.
Change-Id: I5118576c4da4c9746fbacca2cb117695a29d5462
Signed-off-by: Tony Truong <truong@codeaurora.org>
PCIe link states (L0s, L1, and L1ss) can be supported independent
of each other. Add the support in the driver to enable these link
states separately.
Change-Id: Ia7e5eca6c38bc517f39a308aa460c92e864000f4
Signed-off-by: Tony Truong <truong@codeaurora.org>
Update probe state after resources are validated during probe.
Change-Id: Ic5678493e9211282f9b4c95aea6e10cc865d186e
Signed-off-by: Tony Truong <truong@codeaurora.org>
During bootup, client driver may be probed before PCIe bus
driver is probed successfully. Therefore, calls to PCIe APIs
should be handled accordingly. PCIe bus driver will inform
client driver that it is not ready.
Change-Id: Ia01f500adb7db095e15f0ea67ce8bff240dba5fd
Signed-off-by: Tony Truong <truong@codeaurora.org>
The PCIe client has the requirement to keep PCIe link on when the
CPUs go to power collapse. Add the support here for client driver
to keep PCIe link up during the system suspend.
Change-Id: I886990072c9c72c57e30c5c0cceb7eaedca071e6
Signed-off-by: Yan He <yanhe@codeaurora.org>
The client driver can recover the link during linkdown callback.
The change here allows the client to turn off the power of link
when the link status is down.
Change-Id: Ia036199c39c66a6a6e258318b878c9c966c11260
Signed-off-by: Tony Truong <truong@codeaurora.org>
Add PCIe bus driver for msm8994. This driver is based on a 3rd
party arm64 PCI framework from the community which has not been
merged on the upstream yet. PCIe bus driver manages the PCIe
Root Complexes and Endpoints, and configures the legacy PCI
interrupts and MSI interrupts.
Change-Id: Ia271fe6cd54398a5f9d0d65308266edf16f8c97e
Signed-off-by: Yan He <yanhe@codeaurora.org>
Add the new entries for PCIe driver in Kconfig files.
Change-Id: I5575caee4ee59ddbbb2ca8fbced1539b2d4b3f7f
Signed-off-by: Yan He <yanhe@codeaurora.org>
This patch adds the arch support for PCI(e) for arm64. The files
added or modified in this patch are based on PCI(e) support in
32bit arm.
Change-Id: Ie274623b5bf053e63d8857d256cbf91fef80bcf4
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Git-commit: 0dbd501893bc8b003be715b8320e520614bd8ae1
Git-repo: git://kernel.ubuntu.com/ubuntu/ubuntu-trusty.git
[yanhe@codeaurora.org: solve the minor compilation errors]
Signed-off-by: Yan He <yanhe@codeaurora.org>
commit 93fa9d32670f5592c8e56abc9928fc194e1e72fc upstream.
When a new device is added below a hotplug bridge, the bridge's secondary
bus speed and the device's bus speed must match. The shpchp driver
previously checked the bridge's *primary* bus speed, not the secondary bus
speed.
This caused hot-add errors like:
shpchp 0000:00:03.0: Speed of bus ff and adapter 0 mismatch
Check the secondary bus speed instead.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75251
Fixes: 3749c51ac6 ("PCI: Make current and maximum bus speeds part of the PCI core")
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commits have been reverted from this merge, as they are
known to introduce new bugs and are currently incompatible with our
audio implementation. Investigation of these commits is ongoing, and
they are expected to be brought in at a later time:
86e6de7 ALSA: compress: fix drain calls blocking other compress functions (v6)
16442d4 ALSA: compress: fix drain calls blocking other compress functions
This merge commit also includes a change in block, necessary for
compilation. Upstream has modified elevator_init_fn to prevent race
conditions, requring updates to row_init_queue and test_init_queue.
* commit 'v3.10.28': (1964 commits)
Linux 3.10.28
ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling
drm/i915: Don't grab crtc mutexes in intel_modeset_gem_init()
serial: amba-pl011: use port lock to guard control register access
mm: Make {,set}page_address() static inline if WANT_PAGE_VIRTUAL
md/raid5: Fix possible confusion when multiple write errors occur.
md/raid10: fix two bugs in handling of known-bad-blocks.
md/raid10: fix bug when raid10 recovery fails to recover a block.
md: fix problem when adding device to read-only array with bitmap.
drm/i915: fix DDI PLLs HW state readout code
nilfs2: fix segctor bug that causes file system corruption
thp: fix copy_page_rep GPF by testing is_huge_zero_pmd once only
ftrace/x86: Load ftrace_ops in parameter not the variable holding it
SELinux: Fix possible NULL pointer dereference in selinux_inode_permission()
writeback: Fix data corruption on NFS
hwmon: (coretemp) Fix truncated name of alarm attributes
vfs: In d_path don't call d_dname on a mount point
staging: comedi: adl_pci9111: fix incorrect irq passed to request_irq()
staging: comedi: addi_apci_1032: fix subdevice type/flags bug
mm/memory-failure.c: recheck PageHuge() after hugetlb page migrate successfully
GFS2: Increase i_writecount during gfs2_setattr_chown
perf/x86/amd/ibs: Fix waking up from S3 for AMD family 10h
perf scripting perl: Fix build error on Fedora 12
ARM: 7815/1: kexec: offline non panic CPUs on Kdump panic
Linux 3.10.27
sched: Guarantee new group-entities always have weight
sched: Fix hrtimer_cancel()/rq->lock deadlock
sched: Fix cfs_bandwidth misuse of hrtimer_expires_remaining
sched: Fix race on toggling cfs_bandwidth_used
x86, fpu, amd: Clear exceptions in AMD FXSAVE workaround
netfilter: nf_nat: fix access to uninitialized buffer in IRC NAT helper
SCSI: sd: Reduce buffer size for vpd request
intel_pstate: Add X86_FEATURE_APERFMPERF to cpu match parameters.
mac80211: move "bufferable MMPDU" check to fix AP mode scan
ACPI / Battery: Add a _BIX quirk for NEC LZ750/LS
ACPI / TPM: fix memory leak when walking ACPI namespace
mfd: rtsx_pcr: Disable interrupts before cancelling delayed works
clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg clock
clk: samsung: exynos4: Correct SRC_MFC register
clk: clk-divider: fix divisor > 255 bug
ahci: add PCI ID for Marvell 88SE9170 SATA controller
parisc: Ensure full cache coherency for kmap/kunmap
drm/nouveau/bios: make jump conditional
ARM: shmobile: mackerel: Fix coherent DMA mask
ARM: shmobile: armadillo: Fix coherent DMA mask
ARM: shmobile: kzm9g: Fix coherent DMA mask
ARM: dts: exynos5250: Fix MDMA0 clock number
ARM: fix "bad mode in ... handler" message for undefined instructions
ARM: fix footbridge clockevent device
net: Loosen constraints for recalculating checksum in skb_segment()
bridge: use spin_lock_bh() in br_multicast_set_hash_max
netpoll: Fix missing TXQ unlock and and OOPS.
net: llc: fix use after free in llc_ui_recvmsg
virtio-net: fix refill races during restore
virtio_net: don't leak memory or block when too many frags
virtio-net: make all RX paths handle errors consistently
virtio_net: fix error handling for mergeable buffers
vlan: Fix header ops passthru when doing TX VLAN offload.
net: rose: restore old recvmsg behavior
rds: prevent dereference of a NULL device
ipv6: always set the new created dst's from in ip6_rt_copy
net: fec: fix potential use after free
hamradio/yam: fix info leak in ioctl
drivers/net/hamradio: Integer overflow in hdlcdrv_ioctl()
net: inet_diag: zero out uninitialized idiag_{src,dst} fields
ip_gre: fix msg_name parsing for recvfrom/recvmsg
net: unix: allow bind to fail on mutex lock
ipv6: fix illegal mac_header comparison on 32bit
netvsc: don't flush peers notifying work during setting mtu
tg3: Initialize REG_BASE_ADDR at PCI config offset 120 to 0
net: unix: allow set_peek_off to fail
net: drop_monitor: fix the value of maxattr
ipv6: don't count addrconf generated routes against gc limit
packet: fix send path when running with proto == 0
virtio: delete napi structures from netdev before releasing memory
macvtap: signal truncated packets
tun: update file current position
macvtap: update file current position
macvtap: Do not double-count received packets
rds: prevent BUG_ON triggered on congestion update to loopback
net: do not pretend FRAGLIST support
IPv6: Fixed support for blackhole and prohibit routes
HID: Revert "Revert "HID: Fix logitech-dj: missing Unifying device issue""
gpio-rcar: R-Car GPIO IRQ share interrupt
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
irqchip: renesas-irqc: Fix irqc_probe error handling
Linux 3.10.26
sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
ext4: fix bigalloc regression
arm64: Use Normal NonCacheable memory for writecombine
arm64: Do not flush the D-cache for anonymous pages
arm64: Avoid cache flushing in flush_dcache_page()
ARM: KVM: arch_timers: zero CNTVOFF upon return to host
ARM: hyp: initialize CNTVOFF to zero
clocksource: arch_timer: use virtual counters
arm64: Remove unused cpu_name ascii in arch/arm64/mm/proc.S
arm64: dts: Reserve the memory used for secondary CPU release address
arm64: check for number of arguments in syscall_get/set_arguments()
arm64: fix possible invalid FPSIMD initialization state
...
Change-Id: Ia0e5d71b536ab49ec3a1179d59238c05bdd03106
Signed-off-by: Ian Maund <imaund@codeaurora.org>
commit 3cdeb713dc66057b50682048c151eae07b186c42 upstream.
Andreas reported that after 1f42db786b14 ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.
This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.
Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device(). But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.
This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.
Fixes: 1f42db786b14 PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691
Reported-and-tested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f42db786b14a31bf807fc41ee5583a00c08fcb1 upstream.
Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts. Clear Interrupt Disable so we get those interrupts.
Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.
Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng <chris.cheng@atrustcorp.com>
Reported-and-tested-by: Jamie Chen <jamie.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Git-commit: 0244ad004a54e39308d495fee0a2e637f8b5c317
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
[imaund@codeaurora.org: resolve merge conflicts]
Signed-off-by: Ian Maund <imaund@codeaurora.org>
commit 4fc9bbf98fd66f879e628d8537ba7c240be2b58e upstream.
Add a flag to tell the PCI subsystem that kernel is shutting down in
preparation to kexec a kernel. Add code in PCI subsystem to use this flag
to clear Bus Master bit on PCI devices only in case of kexec reboot.
This fixes a power-off problem on Acer Aspire V5-573G and likely other
machines and avoids any other issues caused by clearing Bus Master bit on
PCI devices in normal shutdown path. The problem was introduced by
b566a22c23 ("PCI: disable Bus Master on PCI device shutdown").
This patch is based on discussion at
http://marc.info/?l=linux-pci&m=138425645204355&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63861
Reported-by: Chang Liu <cl91tp@gmail.com>
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7cc5cf74544d97d7b69e2701595037474db1f96 upstream.
The pcie_portdrv .probe() method calls pci_enable_device() once, in
pcie_port_device_register(), but the .remove() method calls
pci_disable_device() twice, in pcie_port_device_remove() and in
pcie_portdrv_remove().
That causes a "disabling already-disabled device" warning when removing a
PCIe port device. This happens all the time when removing Thunderbolt
devices, but is also easy to reproduce with, e.g.,
"echo 0000:00:1c.3 > /sys/bus/pci/drivers/pcieport/unbind"
This patch removes the disable from pcie_portdrv_remove().
[bhelgaas: changelog, tag for stable]
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d3a1741f1e648cfbd5a0cc94477a0d5004c6f5e upstream.
Previously we allowed callers to access Slot Capabilities, Status, and
Control for Root Ports even if the Root Port did not implement a slot.
This seems dubious because the spec only requires these registers if a
slot is implemented.
It's true that even Root Ports without slots must have *space* for these
slot registers, because the Root Capabilities, Status, and Control
registers are after the slot registers in the capability. However,
for a v1 PCIe Capability, the *semantics* of the slot registers are
undefined unless a slot is implemented.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8b303d0206b28c4ff3aecada47108d1655ae00f upstream.
Previously we relied on the PCIe r3.0, sec 7.8, spec language that says
"For Functions that do not implement the [Link, Slot, Root] registers,
these spaces must be hardwired to 0b," which means that for v2 PCIe
capabilities, we don't need to check the device type at all.
But it's simpler if we don't need to check the capability version at all,
and I think the spec is explicit enough about which registers are required
for which types that we can remove the version checks.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3694d4fa3f44f6a295f8ab064937c8a1549d174 upstream.
Every PCIe device has a link, except Root Complex Integrated Endpoints
and Root Complex Event Collectors. Previously we didn't give access
to PCIe capability link-related registers for Upstream Ports, Downstream
Ports, and Bridges, so attempts to read PCI_EXP_LNKCTL incorrectly
returned zero. See PCIe spec r3.0, sec 7.8 and 1.3.2.3.
Reference: http://lkml.kernel.org/r/979A8436335E3744ADCD3A9F2A2B68A52AD136BE@SJEXCHMB10.corp.ad.broadcom.com
Reported-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 834145156bedadfb50121f0bc5e9d9f9f942bcca upstream.
Commit 448bd85 (PCI/PM: add PCIe runtime D3cold support) added a
piece of code to pci_acpi_wake_dev() causing that function to behave
in a special way for devices in D3cold (so that their configuration
registers are not accessed before those devices are resumed).
However, it didn't take the clearing of the pme_poll flag into
account. That has to be done for all devices, even if they are in
D3cold, or pci_pme_list_scan() will not know that wakeup has been
signaled for the device and will poll its PME Status bit
unnecessarily.
Fix the problem by moving the clearing of the pme_poll flag in
pci_acpi_wake_dev() before the code introduced by commit 448bd85.
Reported-and-tested-by: David E. Box <david.e.box@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60f75b8e97daf4a39790a20d962cb861b9220af5 upstream.
In theory, under a given ACPI namespace node there should be only
one child device object with _ADR whose value matches a given bus
address exactly. In practice, however, there are systems in which
multiple child device objects under a given parent have _ADR matching
exactly the same address. In those cases we use _STA to determine
which of the multiple matching devices is enabled, since some systems
are known to indicate which ACPI device object to associate with the
given physical (usually PCI) device this way.
Unfortunately, as it turns out, there are systems in which many
device objects under the same parent have _ADR matching exactly the
same bus address and none of them has _STA, in which case they all
should be regarded as enabled according to the spec. Still, if
those device objects are supposed to represent bridges (e.g. this
is the case for device objects corresponding to PCIe ports), we can
try harder and skip the ones that have no child device objects in the
ACPI namespace. With luck, we can avoid using device objects that we
are not expected to use this way.
Although this only works for bridges whose children also have ACPI
namespace representation, it is sufficient to address graphics
adapter detection issues on some systems, so rework the code finding
a matching device ACPI handle for a given bus address to implement
this idea.
Introduce a new function, acpi_find_child(), taking three arguments:
the ACPI handle of the device's parent, a bus address suitable for
the device's bus type and a bool indicating if the device is a
bridge and make it work as outlined above. Reimplement the function
currently used for this purpose, acpi_get_child(), as a call to
acpi_find_child() with the last argument set to 'false' and make
the PCI subsystem use acpi_find_child() with the bridge information
passed as the last argument to it. [Lan Tianyu notices that it is
not sufficient to use pci_is_bridge() for that, because the device's
subordinate pointer hasn't been set yet at this point, so use
hdr_type instead.]
This change fixes a regression introduced inadvertently by commit
33f767d (ACPI: Rework acpi_get_child() to be more efficient) which
overlooked the fact that for acpi_walk_namespace() "post-order" means
"after all children have been visited" rather than "on the way back",
so for device objects without children and for namespace walks of
depth 1, as in the acpi_get_child() case, the "post-order" callbacks
ordering is actually the same as the ordering of "pre-order" ones.
Since that commit changed the namespace walk in acpi_get_child() to
terminate after finding the first matching object instead of going
through all of them and returning the last one, it effectively
changed the result returned by that function in some rare cases and
that led to problems (the switch from a "pre-order" to a "post-order"
callback was supposed to prevent that from happening, but it was
ineffective).
As it turns out, the systems where the change made by commit
33f767d actually matters are those where there are multiple ACPI
device objects representing the same PCIe port (which effectively
is a bridge). Moreover, only one of them, and the one we are
expected to use, has child device objects in the ACPI namespace,
so the regression can be addressed as described above.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60561
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Vladimir Lalov <mail@vlalov.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa914f5ec25e4371ba18b312971314be1b9b1076 upstream.
Ben Herrenschmidt reported the following problem:
- The bus has space for all desired MMIO resources, including optional
space for SR-IOV devices
- We attempt to allocate I/O port space, but it fails because the bus
has no I/O space
- Because of the I/O allocation failure, we retry MMIO allocation,
requesting only the required space, without the optional SR-IOV space
This means we don't allocate the optional SR-IOV space, even though we
could.
This is related to 0c5be0cb0e ("PCI: Retry on IORESOURCE_IO type
allocations").
This patch changes how we handle allocation failures. We will now retry
allocation of only the resource type that failed. If MMIO allocation
fails, we'll retry only MMIO allocation. If I/O port allocation fails,
we'll retry only I/O port allocation.
[bhelgaas: changelog]
Reference: https://lkml.kernel.org/r/1367712653.11982.19.camel@pasglop
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29ed1f29b68a8395d5679b3c4e38352b617b3236 upstream.
Hot-removing a device with SR-IOV enabled causes a null pointer dereference
in v3.9 and v3.10.
This is a regression caused by ba518e3c17 ("PCI: pciehp: Iterate over all
devices in slot, not functions 0-7"). When we iterate over the
bus->devices list, we first remove the PF, which also removes all the VFs
from the list. Then the list iterator blows up because more than just the
current entry was removed from the list.
ac205b7bb7 ("PCI: make sriov work with hotplug remove") works around a
similar problem in pci_stop_bus_devices() by iterating over the list in
reverse, so the VFs are stopped and removed from the list first, before the
PF.
This patch changes pciehp_unconfigure_device() to iterate over the list in
reverse, too.
[bhelgaas: bugzilla, changelog]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=60604
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 343df771e671d821478dd3ef525a0610b808dbf8 upstream.
After calling device_register(&bridge->dev), the bridge is reference-
counted, and it is illegal to call kfree() on it except in the release
function.
[bhelgaas: changelog, use put_device() after device_register() failure]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbf33f516bdbcc2ab1ba1e54dfb720b0cfaa6874 upstream.
Commit 4f535093cf "PCI: Put pci_dev in device tree as early as possible"
moves device registering from pci_bus_add_devices() to pci_device_add().
That causes problems for virtual functions because device_add(&virtfn->dev)
is called before setting the virtfn->is_virtfn flag, which then causes Xen
to report PCI virtual functions as PCI physical functions.
Fix it by setting virtfn->is_virtfn before calling pci_device_add().
[Jiang Liu]: Move the setting of virtfn->is_virtfn ahead further for better
readability and modify changelog.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 098b1aeaf4d6149953b8f1f8d55c21d85536fbff upstream.
There are two tool-stack that can instruct the Xen PCI frontend
and backend to change states: 'xm' (Python code with a daemon),
and 'xl' (C library - does not keep state changes).
With the 'xm', the path to disconnect a single PCI device (xm pci-detach
<guest> <BDF>) is:
4(Connected)->7(Reconfiguring*)-> 8(Reconfigured)-> 4(Connected)->5(Closing*).
The * is for states that the tool-stack sets. For 'xl', it is similar:
4(Connected)->7(Reconfiguring*)-> 8(Reconfigured)-> 4(Connected)
Both of them also tear down the XenBus structure, so the backend
state ends up going in the 3(Initialised) and calls pcifront_xenbus_remove.
When a PCI device is plugged back in (xm pci-attach <guest> <BDF>)
both of them follow the same pattern:
2(InitWait*), 3(Initialized*), 4(Connected*)->4(Connected).
[xen-pcifront ignores the 2,3 state changes and only acts when
4 (Connected) has been reached]
Note that this is for a _single_ PCI device. If there were two
PCI devices and only one was disconnected 'xm' would show the same
state changes.
The problem is that git commit 3d925320e9
("xen/pcifront: Use Xen-SWIOTLB when initting if required") introduced
a mechanism to initialize the SWIOTLB when the Xen PCI front moves to
Connected state. It also had some aggressive seatbelt code check that
would warn the user if one tried to change to Connected state without
hitting first the Closing state:
pcifront pci-0: PCI frontend already installed!
However, that code can be relaxed and we can continue on working
even if the frontend is instructed to be the 'Connected' state with
no devices and then gets tickled to be in 'Connected' state again.
In other words, this 4(Connected)->5(Closing)->4(Connected) state
was expected, while 4(Connected)->.... anything but 5(Closing)->4(Connected)
was not. This patch removes that aggressive check and allows
Xen pcifront to work with the 'xl' toolstack (for one or more
PCI devices) and with 'xm' toolstack (for more than two PCI
devices).
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
[v2: Added in the description about two PCI devices]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interactions between the ACPI dock driver and the ACPI-based PCI
hotplug (acpiphp) are currently problematic because of ordering
issues during hot-remove operations.
First of all, the current ACPI glue code expects that physical
devices will always be deleted before deleting the companion ACPI
device objects. Otherwise, acpi_unbind_one() will fail with a
warning message printed to the kernel log, for example:
[ 185.026073] usb usb5: Oops, 'acpi_handle' corrupt
[ 185.035150] pci 0000:1b:00.0: Oops, 'acpi_handle' corrupt
[ 185.035515] pci 0000:18:02.0: Oops, 'acpi_handle' corrupt
[ 180.013656] port1: Oops, 'acpi_handle' corrupt
This means, in particular, that struct pci_dev objects have to
be deleted before the struct acpi_device objects they are "glued"
with.
Now, the following happens the during the undocking of an ACPI-based
dock station:
1) hotplug_dock_devices() invokes registered hotplug callbacks to
destroy physical devices associated with the ACPI device objects
depending on the dock station. It calls dd->ops->handler() for
each of those device objects.
2) For PCI devices dd->ops->handler() points to
handle_hotplug_event_func() that queues up a separate work item
to execute _handle_hotplug_event_func() for the given device and
returns immediately. That work item will be executed later.
3) hotplug_dock_devices() calls dock_remove_acpi_device() for each
device depending on the dock station. This runs acpi_bus_trim()
for each of them, which causes the underlying ACPI device object
to be destroyed, but the work items queued up by
handle_hotplug_event_func() haven't been started yet.
4) _handle_hotplug_event_func() queued up in step 2) are executed
and cause the above failure to happen, because the PCI devices
they handle do not have the companion ACPI device objects any
more (those objects have been deleted in step 3).
The possible breakage doesn't end here, though, because
hotplug_dock_devices() may return before at least some of the
_handle_hotplug_event_func() work items spawned by it have a
chance to complete and then undock() will cause _DCK to be
evaluated and that will cause the devices handled by the
_handle_hotplug_event_func() to go away possibly while they are
being accessed.
This means that dd->ops->handler() for PCI devices should not point
to handle_hotplug_event_func(). Instead, it should point to a
function that will do the work of _handle_hotplug_event_func()
synchronously. For this reason, introduce such a function,
hotplug_event_func(), and modity acpiphp_dock_ops to point to
it as the handler.
Unfortunately, however, this is not sufficient, because if the dock
code were not changed further, hotplug_event_func() would now
deadlock with hotplug_dock_devices() that called it, since it would
run unregister_hotplug_dock_device() which in turn would attempt to
acquire the dock station's hp_lock mutex already acquired by
hotplug_dock_devices().
To resolve that deadlock use the observation that
unregister_hotplug_dock_device() won't need to acquire hp_lock
if PCI bridges the devices on the dock station depend on are
prevented from being removed prematurely while the first loop in
hotplug_dock_devices() is in progress.
To make that possible, introduce a mechanism by which the callers of
register_hotplug_dock_device() can provide "init" and "release"
routines that will be executed, respectively, during the addition
and removal of the physical device object associated with the
given ACPI device handle. Make acpiphp use two new functions,
acpiphp_dock_init() and acpiphp_dock_release(), that call
get_bridge() and put_bridge(), respectively, on the acpiphp bridge
holding the given device, for this purpose.
In addition to that, remove the dock station's list of
"hotplug devices" and make the dock code always walk the whole list
of "dependent devices" instead in such a way that the loops in
hotplug_dock_devices() and dock_event() (replacing the loops over
"hotplug devices") will take references to the list entries that
register_hotplug_dock_device() has been called for. That prevents
the "release" routines associated with those entries from being
called while the given entry is being processed and for PCI
devices this means that their bridges won't be removed (by a
concurrent thread) while hotplug_event_func() handling them is
being executed.
This change is based on two earlier patches from Jiang Liu.
References: https://bugzilla.kernel.org/show_bug.cgi?id=59501
Reported-and-tested-by: Alexander E. Patrakov <patrakov@gmail.com>
Tracked-down-by: Jiang Liu <jiang.liu@huawei.com>
Tested-by: Illya Klymov <xanf@xanf.me>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org>
On x86 platforms, the kernel respects PCI resource assignments from
the BIOS and only reassigns resources for unassigned BARs at boot
time. However, with the ACPI-based hotplug (acpiphp), it ignores the
BIOS' PCI resource assignments completely and reassigns all resources
by itself. This causes differences in PCI resource allocation
between boot time and runtime hotplug to occur, which is generally
undesirable and sometimes actively breaks things.
Namely, if there are enough resources, reassigning all PCI resources
during runtime hotplug should work, but it may fail if the resources
are constrained. This may happen, for instance, when some PCI
devices with huge MMIO BARs are involved in the runtime hotplug
operations, because the current PCI MMIO alignment algorithm may
waste huge chunks of MMIO address space in those cases.
On the Alexander's Sony VAIO VPCZ23A4R the BIOS allocates limited
MMIO resources for the dock station which contains a device
(graphics adapter) with a 256MB MMIO BAR. An attempt to reassign
that during runtime hotplug causes the dock station MMIO window to be
exhausted and acpiphp fails to allocate resources for the majority
of devices on the dock station as a result.
To prevent that from happening, modify acpiphp to follow the boot
time resources allocation behavior so that the BIOS' resource
assignments are respected during runtime hotplug too.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=56531
Reported-and-tested-by: Alexander E. Patrakov <patrakov@gmail.com>
Tested-by: Illya Klymov <xanf@xanf.me>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following warning was seen on 3.9 when a corrected PCIe error was being
handled by the AER subsystem.
WARNING: at .../drivers/pci/search.c:214 pci_get_dev_by_id+0x8a/0x90()
This occurred because a call to pci_get_domain_bus_and_slot() was added to
cper_print_pcie() to setup for the call to cper_print_aer(). The warning
showed up because cper_print_pcie() is called in an interrupt context and
pci_get* functions are not supposed to be called in that context.
The solution is to move the cper_print_aer() call out of the interrupt
context and into aer_recover_work_func() to avoid any warnings when calling
pci_get* functions.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When a PCI host bridge device receives a Bus Check notification, we
must re-enumerate starting with the bridge to discover changes (devices
that have been added or removed).
Prior to 668192b678 ("PCI: acpiphp: Move host bridge hotplug to
pci_root.c"), this happened in _handle_hotplug_event_bridge(). After that
commit, _handle_hotplug_event_bridge() is not installed for host bridges,
and the host bridge notify handler, _handle_hotplug_event_root() did not
re-enumerate.
This patch adds re-enumeration to _handle_hotplug_event_root().
This fixes cases where we don't notice the addition or removal of
PCI devices, e.g., the PCI-to-USB ExpressCard in the bugzilla below.
[bhelgaas: changelog, references]
Reference: https://lkml.kernel.org/r/CAAh6nkmbKR3HTqm5ommevsBwhL_u0N8Rk7Wsms_LfP=nBgKNew@mail.gmail.com
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=57961
Reported-by: Gavin Guo <tuffkidtt@gmail.com>
Tested-by: Gavin Guo <tuffkidtt@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.9+
MSI
PCI: Set ->mask_pos correctly
Hotplug
PCI: Delay final fixups until resources are assigned
Moorestown
x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=B2U8
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"MSI:
PCI: Set ->mask_pos correctly
Hotplug:
PCI: Delay final fixups until resources are assigned
Moorestown:
x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
* tag 'pci-v3.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Delay final fixups until resources are assigned
x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0
PCI: Set ->mask_pos correctly
Commit 4f535093cf "PCI: Put pci_dev in device tree as early as possible"
moved final fixups from pci_bus_add_device() to pci_device_add(). But
pci_device_add() happens before resource assignment, so BARs may not be
valid yet.
Typical flow for hot-add:
pciehp_configure_device
pci_scan_slot
pci_scan_single_device
pci_device_add
pci_fixup_device(pci_fixup_final, dev) # previous location
# resource assignment happens here
pci_bus_add_devices
pci_bus_add_device
pci_fixup_device(pci_fixup_final, dev) # new location
[bhelgaas: changelog, move fixups to pci_bus_add_device()]
Reference: https://lkml.kernel.org/r/20130415182614.GB9224@xanatos
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Tested-by: David Bulkow <David.Bulkow@stratus.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.9+
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlights this time around are:
- A pile of addition POWER8 bits and nits, such as updated
performance counter support (Michael Ellerman), new branch history
buffer support (Anshuman Khandual), base support for the new PCI
host bridge when not using the hypervisor (Gavin Shan) and other
random related bits and fixes from various contributors.
- Some rework of our page table format by Aneesh Kumar which fixes a
thing or two and paves the way for THP support. THP itself will
not make it this time around however.
- More Freescale updates, including Altivec support on the new e6500
cores, new PCI controller support, and a pile of new boards support
and updates.
- The usual batch of trivial cleanups & fixes"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
powerpc: Fix build error for book3e
powerpc: Context switch the new EBB SPRs
powerpc: Turn on the EBB H/FSCR bits
powerpc: Replace CPU_FTR_BCTAR with CPU_FTR_ARCH_207S
powerpc: Setup BHRB instructions facility in HFSCR for POWER8
powerpc: Fix interrupt range check on debug exception
powerpc: Update tlbie/tlbiel as per ISA doc
powerpc: Print page size info during boot
powerpc: print both base and actual page size on hash failure
powerpc: Fix hpte_decode to use the correct decoding for page sizes
powerpc: Decode the pte-lp-encoding bits correctly.
powerpc: Use encode avpn where we need only avpn values
powerpc: Reduce PTE table memory wastage
powerpc: Move the pte free routines from common header
powerpc: Reduce the PTE_INDEX_SIZE
powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format
powerpc: New hugepage directory format
powerpc: Don't truncate pgd_index wrongly
powerpc: Don't hard code the size of pte page
powerpc: Save DAR and DSISR in pt_regs on MCE
...
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
The "+" operation has higher precedence than "?:" and ->msi_cap is
always non-zero here so the original statement is equivalent to:
entry->mask_pos = PCI_MSI_MASK_64;
Which wasn't the intent.
[bhelgaas: my fault from 78b5a310ce]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This function is meant to add a helper function that will determine if a PF
has any VFs that are currently assigned to a guest. We currently have been
implementing this function per driver, and going forward I would like to avoid
that by making this function generic and using this helper.
v2: Removed extern from declaration of pci_vfs_assigned in pci.h and return
0 if SR-IOV is disabled with is inline with other PCI SRIOV functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* pci/gavin-msi-cleanup:
vfio-pci: Use cached MSI/MSI-X capabilities
vfio-pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
PCI: Remove "extern" from function declarations
PCI: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
PCI: Drop msi_mask_reg() and remove drivers/pci/msi.h
PCI: Use msix_table_size() directly, drop multi_msix_capable()
PCI: Drop msix_table_offset_reg() and msix_pba_offset_reg() macros
PCI: Drop is_64bit_address() and is_mask_bit_support() macros
PCI: Drop msi_data_reg() macro
PCI: Drop msi_lower_address_reg() and msi_upper_address_reg() macros
PCI: Drop msi_control_reg() macro and use PCI_MSI_FLAGS directly
PCI: Use cached MSI/MSI-X offsets from dev, not from msi_desc
PCI: Clean up MSI/MSI-X capability #defines
PCI: Use cached MSI-X cap while enabling MSI-X
PCI: Use cached MSI cap while enabling MSI interrupts
PCI: Remove MSI/MSI-X cap check in pci_msi_check_device()
PCI: Cache MSI/MSI-X capability offsets in struct pci_dev
PCI: Use u8, not int, for PM capability offset
[SCSI] megaraid_sas: Use correct #define for MSI-X capability
PCI_MSIX_FLAGS_BIRMASK is mis-named because the BIR mask is in the
Table Offset register, not the flags ("Message Control" per spec)
register.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
msi_mask_reg() doesn't provide any useful abstraction, do drop it.
Remove the now-empty drivers/pci/msi.h.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The users of multi_msix_capable() are really interested in the table
size, so just say what we mean.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
msix_table_offset_reg() is used only once and adds a useless indirection,
so just use the table offset directly.
msix_pba_offset_reg() is unused, so just delete it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
msi_lower_address_reg() and msi_upper_address_reg() don't provide any
useful abstraction, so drop them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Note the error in pci_msix_table_size() -- we used PCI_MSI_FLAGS to
locate the PCI_MSIX_FLAGS word. No actual breakage because PCI_MSI_FLAGS
and PCI_MSIX_FLAGS happen to be the same.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We always know the type (MSI vs MSI-X), so we can use the correct
cached capability offset rather than relying on the copy in the
msi_attrib.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The patch uses the cached MSI-X capability offset in
pci_dev instead of reading it from config space when enabling
MSI-X interrupts.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The patch uses the cached MSI capability offset in pci_dev instead
of reading it from config space when enabling MSI interrupts.
[bhelgaas: removed unrelated msi_control_reg() changes]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function pci_msi_check_device() is called while enabling MSI
or MSI-X interrupts to make sure the PCI device can support MSI
or MSI-X capability. This patch removes the check on MSI or MSI-X
capability in the function and lets the caller do the check.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The patch caches the MSI and MSI-X capability offset in PCI device
(struct pci_dev) so that we needn't read it from the config space
upon enabling or disabling MSI or MSI-X interrupts.
[bhelgaas: moved pm_cap size change to separate patch]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set dev->dev.type in alloc_pci_dev so that archs that have their own
versions of pci_setup_device get this set properly in order to ensure
things like the boot_vga sysfs parameter get created as expected.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
* pci/cleanup:
PCI: Remove "extern" from function declarations
PCI: Warn about failures instead of "must_check" functions
PCI: Remove __must_check from definitions
PCI: Remove unused variables
PCI: Move cpci_hotplug_init() proto to header file
PCI: Make local functions/structs static
PCI: Fix missing prototype for pcie_port_acpi_setup()
Conflicts:
drivers/pci/hotplug/acpiphp.h
include/linux/pci.h
We had an inconsistent mix of using and omitting the "extern" keyword
on function declarations in header files. This removes them all.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These places capture return values to avoid "must_check" warnings,
but we didn't *do* anything with the return values, which causes
"set but not used" warnings. We might as well do something instead
of just trying to evade the "must_check" warnings.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The __must_check (gcc "warn_unused_result") attribute only makes sense
when compiling the *caller* of the function, so the attribute should
appear on the declaration in the header file, not on the definition.
The declarations of these functions are already annotated with
__must_check.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Don't modify function handles to get a disabled handle - call
clp_disable_fh. With this change we also do no longer deconfigure
enabled functions.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the debugfs to keep track of a pci function's status changes.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* pci/jiang-subdrivers:
PCI/ACPI: Remove support of ACPI PCI subdrivers
PCI: acpiphp: Protect acpiphp data structures from concurrent updates
PCI: acpiphp: Use normal list to simplify implementation
PCI: acpiphp: Do not use ACPI PCI subdriver mechanism
PCI: acpiphp: Convert acpiphp to be builtin only, not modular
PCI/ACPI: Handle PCI slot devices when creating/destroying PCI buses
x86/PCI: Implement pcibios_{add|remove}_bus() hooks
ia64/PCI: Implement pcibios_{add|remove}_bus() hooks
PCI/ACPI: Prepare stub functions to handle ACPI PCI (hotplug) slots
PCI: Add pcibios hooks for adding and removing PCI buses
PCI: acpiphp: Replace local macros with standard ACPI macros
PCI: acpiphp: Remove all functions even if function 0 doesn't exist
PCI: acpiphp: Use list_for_each_entry_safe() in acpiphp_sanitize_bus()
PCI: Clean up usages of pci_bus->is_added
PCI: When removing bus, always remove legacy files & unregister
Now acpiphp_enumerate_slots() and acpiphp_remove_slots() may be invoked
concurrently by the PCI core, so add a bridge_mutex and reference count
mechanism to protect acpiphp bridge/slot/function data structures.
To avoid deadlock, handle_hotplug_event_bridge() will requeue the
hotplug event onto the kacpi_hotplug_wq by calling alloc_acpi_hp_work().
But the workaround has introduced a minor race window because the
'bridge' passed to _handle_hotplug_event_bridge() may have already been
destroyed when _handle_hotplug_event_bridge() is actually executed by
the kacpi_hotplug_wq. So hold a reference count on the passed 'bridge'.
Fix the same issue for handle_hotplug_event_func() too.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Use normal list for struct acpiphp_slot to simplify implementation.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
* pci/misc:
PCI: Clean up quirk_io_region
PCI: Use vma_pages() to replace (vm_end - vm_start) >> PAGE_SHIFT
PCI: Use PCI_EXP_SLTCAP_PSN mask when extracting slot number
PCI: Remove unnecessary dependencies between PME and ACPI
[SCSI] mvumi: Use PCI_VENDOR_ID_MARVELL_EXT for 0x1b4b
[SCSI] mvsas: Use PCI_VENDOR_ID_MARVELL_EXT for 0x1b4b
ahci: Use PCI_VENDOR_ID_MARVELL_EXT for 0x1b4b
PCI: Define macro for Marvell vendor ID
PCI: Add MSI INTX_DISABLE quirks for AR8161/AR8162/AR8171/AR8172/E210X
PCI: aer_inject: Fix return values when device not found
Before every call of quirk_io_region(), pci_read_config_word() is called.
We can fold that call into quirk_io_region() to make code more readable.
[bhelgaas: changelog, fill bus_region directly rather than copying from res]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
(*->vm_end - *->vm_start) >> PAGE_SHIFT operation is implemented
as an inline funcion vma_pages() in linux/mm.h, so use it.
Signed-off-by: Libin <huawei.libin@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use PCI_EXP_SLTCAP_PSN mask to make it easier to find where the
Physical Slot Number is used.
The Physical Slot Number is bits 31:19 of the Slot Capabilities Register,
and slot_cap is a u32, so the mask is technically unnecessary, but it's
helpful for human readers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe PME doesn't depend on ACPI, so remove the #includes and
Kconfig dependency.
Based-on-patch-by: Andrew Murray <Andrew.Murray@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make pci_pme_active() ignore devices without PME support, so that
it doesn't print the "PME enabled" or "PME disabled" debug messages
for devices that don't support PME.
So that pci_pme_active() doesn't have to check pm_cap in addition
to pme_support, make pci_pm_init() clear pme_support upfront to
make sure that it will be 0 for pm_cap equal to 0.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b51306c (PCI: Set device power state to PCI_D0 for device
without native PM support) modified pci_platform_power_transition()
by adding code causing dev->current_state for devices that don't
support native PCI PM but are power-manageable by the platform to be
changed to PCI_D0 regardless of the value returned by the preceding
platform_pci_set_power_state(). In particular, that also is done
if the platform_pci_set_power_state() has been successful, which
causes the correct power state of the device set by
pci_update_current_state() in that case to be overwritten by PCI_D0.
Fix that mistake by making the fallback to PCI_D0 only happen if
the platform_pci_set_power_state() has returned an error.
[bhelgaas: folded in Yinghai's simplification, added URL & stable info]
Reference: http://lkml.kernel.org/r/27806FC4E5928A408B78E88BBC67A2306F466BBA@ORSMSX101.amr.corp.intel.com
Reported-by: Chris J. Benenati <chris.j.benenati@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@vger.kernel.org> # v3.2+
cpci_hotplug_init() and cpci_hotplug_exit() are defined in
cpci_hotplug_core.c but had extern declarations in pci_hotplug_core.c.
This puts the declarations in a header file included both places so
the compiler can help keep everything consistent.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously the acpiphp driver registered itself as an ACPI PCI subdriver,
so its callbacks were invoked when creating/destroying PCI root
buses to manage ACPI-based PCI hotplug slots. But it doesn't handle
P2P bridge hotplug events, so it will cause strange behaviour if there
are hotplug slots associated with a hot-removed P2P bridge.
This patch fixes this issue by:
1) Directly hooking into PCI core to update hotplug slot devices when
creating/destroying PCI buses through:
pci_{add|remove}_bus() -> acpi_pci_{add|remove}_bus()
2) Getting rid of unused ACPI PCI subdriver-related code
It also cleans up unused code in the acpiphp driver.
[bhelgaas: keep acpi_pci_add_bus() stub for CONFIG_ACPI=n]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Convert acpiphp to be builtin only, with no module option.
Previously, when HOTPLUG_PCI_ACPI=m, users could disable acpiphp by
removing the module or preventing it from loading. That can't be done
if acpiphp is builtin statically, so this adds an "acpiphp.disable"
kernel parameter. If a user needs to use this parameter, it is a bug,
and we want to hear about it.
[bhelgaas: fold in acpiphp.disable here, remove documentation]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the pci_slot driver doesn't update PCI slot devices when PCI
device hotplug event happens, which may cause memory leak and returning
stale information to user.
Now the pci_slot driver has been changed as built-in driver, so invoke
PCI slot enumeration and destroy routines directly from the PCI core.
And remove ACPI PCI sub-driver related code because it isn't needed
any more.
[bhelgas: removed "extern" from function declarations]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Prepare two stub functions to handle ACPI PCI slots and ACPI PCI hotplug
slots, which will be invoked by the PCI core when creating/destroying
PCI buses.
It will be used to get rid of ACPI PCI subdrivers for pci_slot and
acpiphp, and eventually remove the ACPI PCI subdriver mechanism.
And it will also be used to handle ACPI PCI (hotplug) slots in a unified
way, both at boot time and for PCI hotplug operations.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Myron Stowe <myron.stowe@redhat.com>
On ACPI-based platforms, the pci_slot driver creates PCI slot devices
according to information from ACPI tables by registering an ACPI PCI
subdriver. The ACPI PCI subdriver will only be called when creating/
destroying PCI root buses, and it won't be called when hot-plugging
P2P bridges. It may cause stale PCI slot devices after hot-removing
a P2P bridge if that bridge has associated PCI slots. And the acpiphp
driver has the same issue too.
This patch introduces two hook points into the PCI core, which will
be invoked when creating/destroying PCI buses for PCI host and P2P
bridges. They could be used to setup/destroy platform dependent stuff
in a unified way, both at boot time and for PCI hotplug operations.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Myron Stowe <myron.stowe@redhat.com>
Replace local defined macros (ACPI_STA_xxx) with standard ACPI macros
(ACPI_STA_DEVICE_xxx).
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Currently function disable_device() detects slot state by checking
existence of PCI function 0. It's unreliable because the PCI device
for function 0 may be removed through the sysfs interface. If that
happens, it will cause powering off a hotplug slot without destroying
all PCI devices.
On the other hand, it won't hurt us except wasting some computation
power if the check is removed, because all code of disable_device()
is self-protected. So remove the check.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Function acpiphp_sanitize_bus() may call pci_stop_and_remove_bus_device(),
which in turn may remove device from bus->devices list. So walk the
bus->devices list with list_for_each_entry_safe().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Now pci_bus->is_added is only used to guard invoking of
pcibios_fixup_bus() in pci_scan_child_bus(), so just set
it directly after the fixups and remove the other test
and set in pci_bus_add_devices().
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
We always call device_register() and pci_create_legacy_files() for a
new bus before handing out the "struct pci_bus *". Therefore, there's
no possiblity of removing the bus with pci_remove_bus() before those
calls have been made, so we don't need to check "bus->is_added" before
calling pci_remove_legacy_files() and device_unregister().
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
This fixes a "no previous prototype" warning for pcie_port_acpi_setup()
found via "make W=1".
[bhelgaas: changelog]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The following PCIe devices with revision lower than 0x18 have this bug:
AR8161(1091)/AR8162(1090)/AR8171(10A1)/AR8172(10A0)/E210X(E091).
Signed-off-by: Huang,Xiong <xiong@qca.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Currently the aer_inject driver returns -ENOTTY when the target PCIe
device root port is not found or if the device or root port doesn't
support AER.
In the case where the root port isn't found, the driver should return
-ENODEV, and in the other cases it should return -EPERM.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The runtime PM of PCIe ports turns out to be quite fragile, as in
some cases things work while in some other cases they don't and we
don't seem to have a good way to determine whether or not they are
going to work in advance.
For this reason, avoid enabling runtime PM for PCIe ports by
keeping their runtime PM reference counters always above 0 for the
time being.
When a PCIe port is suspended, it can no longer report events like
hotplug, so hotplug below the port may not work, as in the bug
report below.
[bhelgaas: changelog, stable]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53811
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.6+
It turns out that the _Lxx control methods provided by some BIOSes
clear the PME Status bit of PCI devices they handle, which means that
pci_acpi_wake_dev() cannot really use that bit to check whether or
not the device has signalled wakeup.
One symptom of the problem is, for example, that when an affected PCI
USB controller is runtime-suspended, then plugging in a new USB device
into one of the controller's ports will not wake up the controller,
which should happen.
For this reason, make pci_acpi_wake_dev() always attempt to resume
the device it is called for regardless of the device's PME Status bit
value (that bit still has to be cleared if set at this point,
though).
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
CC: stable@vger.kernel.org # v3.7+
This is a fix for commit 7897e60227 ("PCI: Disable Bus Master
unconditionally in pci_device_shutdown()"). Vivek reported that
with this commit, kexec failed because none of his SATA disks
came up.
A ->shutdown() callback might put the device in D3cold, which means config
space is no longer available.
[bhelgaas: changelog]
Link: https://lkml.org/lkml/2013/3/12/529
Reported-and-Tested-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It turns out that some UEFI systems provide apparently an apparently valid
PCI ROM BAR that turns out to contain garbage, so the attempt in 547b52463
to prefer the ROM from the BAR actually breaks a different set of machines.
As Linus pointed out, the graphics drivers are probably in the best
position to make this judgement, so this basically reverts 547b52463 and
f9a37be0f and adds a new helper function. Followup patches will add support
to nouveau and radeon for probing this ROM source if they can't find a ROM
from some other source.
[bhelgaas: added reporter and bugzilla pointers, s/f4eb5ff05/547b52463]
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=927451
Reference: http://lkml.kernel.org/r/kg69ef$vdb$1@ger.gmane.org
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Reported-by: Chris Murphy <bugzilla@colorremedies.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Change to remove local PCI_BUS() define and use the new PCI_BUS_NUM()
interface from PCI.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Mantas Mikulėnas reported that his graphics hardware failed to
initialise after commit f9a37be0f0 ("x86: Use PCI setup data").
The aim of this commit was to ensure that ROM images were available on
some Apple systems that don't expose the GPU ROM via any other source.
In this case, UEFI appears to have provided a broken ROM image that we
were using even though there was a perfectly valid ROM available via
other sources. The simplest way to handle this seems to be to just
re-order pci_map_rom() and leave any firmare-supplied ROM to last.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ER3b
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from
Rafael J. Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng
with contributions from Aaron Lu, Chao Guan, Jesper Juhl, and
Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri
with contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from
Dirk Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King,
Davidlohr Bueso, Joseph Salisbury, Kees Cook, Li Fei,
Nishanth Menon, ShuoX Liu, Srinivas Pandruvada, Tejun Heo,
Thomas Renninger, and Yasuaki Ishimatsu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=wijn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from Rafael
J Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng with
contributions from Aaron Lu, Chao Guan, Jesper Juhl, and Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri with
contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from Dirk
Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King, Davidlohr Bueso,
Joseph Salisbury, Kees Cook, Li Fei, Nishanth Menon, ShuoX Liu,
Srinivas Pandruvada, Tejun Heo, Thomas Renninger, and Yasuaki
Ishimatsu.
* tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (267 commits)
PM idle: remove global declaration of pm_idle
unicore32 idle: delete stray pm_idle comment
openrisc idle: delete pm_idle
mn10300 idle: delete pm_idle
microblaze idle: delete pm_idle
m32r idle: delete pm_idle, and other dead idle code
ia64 idle: delete pm_idle
cris idle: delete idle and pm_idle
ARM64 idle: delete pm_idle
ARM idle: delete pm_idle
blackfin idle: delete pm_idle
sparc idle: rename pm_idle to sparc_idle
sh idle: rename global pm_idle to static sh_idle
x86 idle: rename global pm_idle to static x86_idle
APM idle: register apm_cpu_idle via cpuidle
cpufreq / intel_pstate: Add kernel command line option disable intel_pstate.
cpufreq / intel_pstate: Change to disallow module build
tools/power turbostat: display SMI count by default
intel_idle: export both C1 and C1E
ACPI / hotplug: Fix concurrency issues and memory leaks
...
Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
Pull perf changes from Ingo Molnar:
"There are lots of improvements, the biggest changes are:
Main kernel side changes:
- Improve uprobes performance by adding 'pre-filtering' support, by
Oleg Nesterov.
- Make some POWER7 events available in sysfs, equivalent to what was
done on x86, from Sukadev Bhattiprolu.
- tracing updates by Steve Rostedt - mostly misc fixes and smaller
improvements.
- Use perf/event tracing to report PCI Express advanced errors, by
Tony Luck.
- Enable northbridge performance counters on AMD family 15h, by Jacob
Shin.
- This tracing commit:
tracing: Remove the extra 4 bytes of padding in events
changes the ABI. All involved parties (PowerTop in particular)
seem to agree that it's safe to do now with the introduction of
libtraceevent, but the devil is in the details ...
Main tooling side changes:
- Add 'event group view', from Namyung Kim:
To use it, 'perf record' should group events when recording. And
then perf report parses the saved group relation from file header
and prints them together if --group option is provided. You can
use the 'perf evlist' command to see event group information:
$ perf record -e '{ref-cycles,cycles}' noploop 1
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.385 MB perf.data (~16807 samples) ]
$ perf evlist --group
{ref-cycles,cycles}
With this example, default perf report will show you each event
separately.
You can use --group option to enable event group view:
$ perf report --group
...
# group: {ref-cycles,cycles}
# ========
# Samples: 7K of event 'anon group { ref-cycles, cycles }'
# Event count (approx.): 6876107743
#
# Overhead Command Shared Object Symbol
# ................ ....... ................. ..........................
99.84% 99.76% noploop noploop [.] main
0.07% 0.00% noploop ld-2.15.so [.] strcmp
0.03% 0.00% noploop [kernel.kallsyms] [k] timerqueue_del
0.03% 0.03% noploop [kernel.kallsyms] [k] sched_clock_cpu
0.02% 0.00% noploop [kernel.kallsyms] [k] account_user_time
0.01% 0.00% noploop [kernel.kallsyms] [k] __alloc_pages_nodemask
0.00% 0.00% noploop [kernel.kallsyms] [k] native_write_msr_safe
0.00% 0.11% noploop [kernel.kallsyms] [k] _raw_spin_lock
0.00% 0.06% noploop [kernel.kallsyms] [k] find_get_page
0.00% 0.02% noploop [kernel.kallsyms] [k] rcu_check_callbacks
0.00% 0.02% noploop [kernel.kallsyms] [k] __current_kernel_time
As you can see the Overhead column now contains both of ref-cycles
and cycles and header line shows group information also - 'anon
group { ref-cycles, cycles }'. The output is sorted by period of
group leader first.
- Initial GTK+ annotate browser, from Namhyung Kim.
- Add option for runtime switching perf data file in perf report,
just press 's' and a menu with the valid files found in the current
directory will be presented, from Feng Tang.
- Add support to display whole group data for raw columns, from Jiri
Olsa.
- Add per processor socket count aggregation in perf stat, from
Stephane Eranian.
- Add interval printing in 'perf stat', from Stephane Eranian.
- 'perf test' improvements
- Add support for wildcards in tracepoint system name, from Jiri
Olsa.
- Add anonymous huge page recognition, from Joshua Zhu.
- perf build-id cache now can show DSOs present in a perf.data file
that are not in the cache, to integrate with build-id servers being
put in place by organizations such as Fedora.
- perf top now shares more of the evsel config/creation routines with
'record', paving the way for further integration like 'top'
snapshots, etc.
- perf top now supports DWARF callchains.
- Fix mmap limitations on 32-bit, fix from David Miller.
- 'perf bench numa mem' NUMA performance measurement suite
- ... and lots of fixes, performance improvements, cleanups and other
improvements I failed to list - see the shortlog and git log for
details."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (270 commits)
perf/x86/amd: Enable northbridge performance counters on AMD family 15h
perf/hwbp: Fix cleanup in case of kzalloc failure
perf tools: Fix build with bison 2.3 and older.
perf tools: Limit unwind support to x86 archs
perf annotate: Make it to be able to skip unannotatable symbols
perf gtk/annotate: Fail early if it can't annotate
perf gtk/annotate: Show source lines with gray color
perf gtk/annotate: Support multiple event annotation
perf ui/gtk: Implement basic GTK2 annotation browser
perf annotate: Fix warning message on a missing vmlinux
perf buildid-cache: Add --update option
uprobes/perf: Avoid uprobe_apply() whenever possible
uprobes/perf: Teach trace_uprobe/perf code to use UPROBE_HANDLER_REMOVE
uprobes/perf: Teach trace_uprobe/perf code to pre-filter
uprobes/perf: Teach trace_uprobe/perf code to track the active perf_event's
uprobes: Introduce uprobe_apply()
perf: Introduce hw_perf_event->tp_target and ->tp_list
uprobes/perf: Always increment trace_uprobe->nhit
uprobes/tracing: Kill uprobe_trace_consumer, embed uprobe_consumer into trace_uprobe
uprobes/tracing: Introduce is_trace_uprobe_enabled()
...
Previously, we cached _PRT (PCI routing table, ACPI 5.0 sec 6.2.12)
contents and associated each _PRT entry with a PCI bus number. The bus
number association means dependencies on PCI device enumeration and bus
number assignment, as well as on the PCI/ACPI binding process.
After 4f535093cf ("PCI: Put pci_dev in device tree as early as possible"),
these dependencies caused the IRQ issues reported by Peter:
pci 0000:00:1e.0: PCI bridge to [bus 09] (subtractive decode)
pci 0000:00:1e.0: can't derive routing for PCI INT A
snd_ctxfi 0000:09:02.0: PCI INT A: no GSI - using ISA IRQ 5
irq 18: nobody cared (try booting with the "irqpoll" option)
This patch removes _PRT caching. Instead, we evaluate _PRT as needed
in the pci_enable_device() path. This also removes the dependency on
PCI bus numbers: we can simply look at the _PRT associated with each
bridge as we walk upstream toward the root.
[bhelgaas: changelog]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53561
Reported-and-tested-by: Peter Hurley <peter@hurleysoftware.com>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Hotplug
PCI/PM: Clean up PME state when removing a device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zdXb
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This is another fix for v3.8. It fixes an oops that happens when a
Thunderbolt adapter is unplugged (remove device, poll for PME events
on no-longer-existing device, oops)."
* tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Clean up PME state when removing a device
PCI_EXP_FLAGS_TYPE is a mask, not an offset. Fix it.
Previously, pcie_capability_read_word(..., PCI_EXP_FLAGS, ...) would
fail.
[bhelgaas: tweak changelog]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.7+
Loading the pci hotplug module when no devices are present will fail
but unfortunately some hotplug callbacks stay registered to the pci
bus level. Fix this by not letting module loading fail when no pci
devices are present and provide proper {de}registration functions
for these callbacks.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pci_probe is too generic and has a name clash with other common code parts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Devices are added to pci_pme_list when drivers use pci_enable_wake()
or pci_wake_from_d3(), but they aren't removed from the list unless
the driver explicitly disables wakeup. Many drivers never disable
wakeup, so their devices remain on the list even after they are
removed, e.g., via hotplug. A subsequent PME poll will oops when
it tries to touch the device.
This patch disables PME# on a device before removing it, which removes
the device from pci_pme_list. This is safe even if the device never
had PME# enabled.
This oops can be triggered by unplugging a Thunderbolt ethernet adapter
on a Macbook Pro, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2svG21yiM1wkH4_2pen2n+cr2-Zv7TbH3Gj+8MwevZjDbw@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
This changeset is aimed at fixing a few different but related
problems in the ACPI hotplug infrastructure.
First of all, since notify handlers may be run in parallel with
acpi_bus_scan(), acpi_bus_trim() and acpi_bus_hot_remove_device()
and some of them are installed for ACPI handles that have no struct
acpi_device objects attached (i.e. before those objects are created),
those notify handlers have to take acpi_scan_lock to prevent races
from taking place (e.g. a struct acpi_device is found to be present
for the given ACPI handle, but right after that it is removed by
acpi_bus_trim() running in parallel to the given notify handler).
Moreover, since some of them call acpi_bus_scan() and
acpi_bus_trim(), this leads to the conclusion that acpi_scan_lock
should be acquired by the callers of these two funtions rather by
these functions themselves.
For these reasons, make all notify handlers that can handle device
addition and eject events take acpi_scan_lock and remove the
acpi_scan_lock locking from acpi_bus_scan() and acpi_bus_trim().
Accordingly, update all of their users to make sure that they
are always called under acpi_scan_lock.
Furthermore, since eject operations are carried out asynchronously
with respect to the notify events that trigger them, with the help
of acpi_bus_hot_remove_device(), even if notify handlers take the
ACPI scan lock, it still is possible that, for example,
acpi_bus_trim() will run between acpi_bus_hot_remove_device() and
the notify handler that scheduled its execution and that
acpi_bus_trim() will remove the device node passed to
acpi_bus_hot_remove_device() for ejection. In that case, the struct
acpi_device object obtained by acpi_bus_hot_remove_device() will be
invalid and not-so-funny things will ensue. To protect agaist that,
make the users of acpi_bus_hot_remove_device() run get_device() on
ACPI device node objects that are about to be passed to it and make
acpi_bus_hot_remove_device() run put_device() on them and check if
their ACPI handles are not NULL (make acpi_device_unregister() clear
the device nodes' ACPI handles for that check to work).
Finally, observe that acpi_os_hotplug_execute() actually can fail,
in which case its caller ought to free memory allocated for the
context object to prevent leaks from happening. It also needs to
run put_device() on the device node that it ran get_device() on
previously in that case. Modify the code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
* pci/konstantin-runtime-pm:
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
This patch clears pci_dev->state_saved at the beginning of suspending.
PCI config state may be saved long before that. Some drivers call
pci_save_state() from the ->probe() callback to get snapshot of sane
configuration space to use in the ->slot_reset() callback.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> # add comment
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
No functional change; just use atomic_inc_return() rather than the
general-purpose atomic_add_return().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Warn when disabling a device that has already been disabled.
[bhelgaas: message wording]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit b566a22c23 ("PCI: disable Bus Master on PCI device shutdown")
used pci_disable_device(), but that doesn't disable Bus Mastering
unconditionally; we allow nested enable/disable calls, and only the
last disable call actually does anything.
This uses pci_clear_master() to unconditionally clear the Bus Master
bit.
Matthew Garrett and Alan Cox said (see LKML link below) that clearing Bus
Master for all PCI devices may lead to unpredictable consequences: some
devices ignores this bit and continue DMA, some of them hang after that or
crash the whole system. But we're already trying to clear Bus Master in
general because of b566a22c23; this merely deals with the cases where
drivers haven't shut down the device correctly.
[bhelgaas: changelog]
Link: https://lkml.org/lkml/2012/6/6/278
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 668192b678 "PCI: acpiphp: Move host bridge hotplug
to pci_root.c" has moved PCI host bridge hotplug logic from acpiphp
to pci_root, but there is still PCI host bridge hotplug related
dead code left in acpiphp. So remove those dead code.
Now companion ACPI devices are always created before corresponding
PCI devices. And the ACPI event handle_hotplug_event_bridge() will be
installed only if it has associated PCI device. So remove dead code to
handle bridge hot-adding in function handle_hotplug_event_bridge().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With commit 4f535093cf "PCI: Put pci_dev in device tree as
early as possible", companion ACPI devices should be created before
creating corresponding PCI devices, otherwise it will break the ACPI
PCI binding logic.
Without this patch, the /sys/bus/pci/devices/.../firmware_node symlink
is missing after hot-removing and hot-adding a device with acpiphp.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In each suspend and resume cycle my laptop prints these messages at
KERN_INFO level:
pciehp 0000:00:1c.1:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
and
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.1:pcie04: pciehp_resume ENTRY
Drop these messages, that were probably used to debug the suspend and
resume code, but now serve no purpose.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Don't allocate and track PCIe ASPM state when "pcie_aspm=off" is specified
on the kernel command line.
Based-on-patch-from: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Bulkow <david.bulkow@stratus.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
On PCI bus hotplug removal, pcie_aspm_exit_link_state() can potentially
skip parent devices that have link_state allocated. Instead of exiting
early if a given device is not PCIe, check whether or not the device's
parent has link_state allocated. This enables pcie_aspm_exit_link_state()
to properly clean up parent link_state when the last function in a slot
might not be PCIe.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/yinghai-root-bus-hotplug:
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
PCI/ACPI: Print info if host bridge notify handler installation fails
PCI: acpiphp: Move host bridge hotplug to pci_root.c
PCI/ACPI: acpiphp: Rename alloc_acpiphp_hp_work() to alloc_acpi_hp_work()
PCI: Make device create/destroy logic symmetric
PCI: Fix reference count leak in pci_dev_present()
PCI: Set pci_dev dev_node early so IOAPIC irq_descs are allocated locally
PCI: Add root bus children dev's res to fail list
PCI: acpiphp: Add is_hotplug_bridge detection
Conflicts:
drivers/pci/pci.h
* pci/acpi-scan2:
ACPI / scan: Drop acpi_bus_add() and use acpi_bus_scan() instead
ACPI: update ej_event interface to take acpi_device
ACPI / scan: Add second pass to acpi_bus_trim()
ACPI / scan: Change the implementation of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_device_unregister()
ACPI: Remove the ops field from struct acpi_device
ACPI: remove unused acpi_op_bind and acpi_op_unbind
ACPI / scan: Fix check of device_attach() return value.
* pci/yijing-ari:
PCI: shpchp: Iterate over all devices in slot, not functions 0-7
PCI: sgihp: Iterate over all devices in slot, not functions 0-7
PCI: cpcihp: Iterate over all devices in slot, not functions 0-7
PCI: pciehp: Iterate over all devices in slot, not functions 0-7
PCI: Consolidate "next-function" functions
PCI: Rename pci_enable_ari() to pci_configure_ari()
PCI: Enable ARI if dev and upstream bridge support it; disable otherwise
Since acpi_bus_trim() cannot fail, change its definition to a void
function, so that its callers don't check the return value in vain
and update the callers.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
We want to put pci_dev structs in the device tree as soon as possible so
for_each_pci_dev() iteration will not miss them, but driver attachment
needs to be delayed until after pci_assign_unassigned_resources() to make
sure all devices have resources assigned first.
This patch moves device registering from pci_bus_add_devices() to
pci_device_add(), which happens earlier, leaving driver attachment in
pci_bus_add_devices().
It also removes unattached child bus handling in pci_bus_add_devices().
That's not needed because child bus via pci_add_new_bus() is already
in parent bus children list.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We want to add PCI devices to the device tree as early as possible but
delay attaching drivers.
device_add() adds a device to the device hierarchy and (via
device_attach()) attaches a matching driver and calls its .probe() method.
We want to separate adding the device to the hierarchy from attaching the
driver.
This patch does that by adding "match_driver" in struct pci_dev. When
false, we return failure from pci_bus_match(), which makes device_attach()
believe there's no matching driver.
Later, we set "match_driver = true" and call device_attach() again, which
now attaches the driver and calls its .probe() method.
[bhelgaas: changelog, explicitly init dev->match_driver,
fold device_attach() call into pci_bus_add_device()]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Could have root bus hot-added later and there may be slots that need
acpiphp.
The result returned by acpiphp_get_num_slots() is meaningless, because
the bridge the slots are under may be added after this function has been
called, so drop acpiphp_get_num_slots() and the code using it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpiphp driver is confusing because it contains partial support for PCI
host bridge hotplug as well as support for hotplug of PCI devices.
This patch moves the host bridge hot-add support to pci_root.c and adds
hot-remove support in pci_root.c.
How to test it: if sci_emu patch is applied, find out root bus number to
ACPI root name mapping from dmesg or /sys. To remove root bus:
echo "\_SB.PCIB 3" > /sys/kernel/debug/acpi/sci_notify
To add back root bus:
echo "\_SB.PCIB 1" > /sys/kernel/debug/acpi/sci_notify
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Will need to use it for PCI root bridge hotplug support, so rename
*acpiphp* to *acpi* and move to osc.c. Also make kacpi_hotplug_wq static
after that.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
According to device model documentation, the way to create/destroy PCI
devices should be symmetric. The rule is to either use
1) device_register()/device_unregister()
or
2) device_initialize()/device_add()/device_del()/put_device().
So change PCI core logic to follow the rule and get rid of the redundant
pci_dev_get()/pci_dev_put() pair.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tony Truong
Bjorn Helgaas
Thomas Jarosch
Linux Build Service Account
Yan He
Tanmay Inamdar
Marcel Apfelbaum
Ian Maund
Martin Schwidefsky
Khalid Aziz
Yinghai Lu
Rafael J. Wysocki
Shane Huang
Jiang Liu
Xudong Hao
Konrad Rzeszutek Wilk
Jiang Liu
Lance Ortiz
Linus Torvalds
David Howells
Dan Carpenter
Alexander Duyck
Gavin Shan
Brian King
Sebastian Ott
Yijing Wang
Libin
Andy Shevchenko
Al Viro
Xiong Huang
Prarit Bhargava
Konstantin Khlebnikov
Matthew Garrett
Shuah Khan
Sasha Levin
Alex Williamson
Heiko Carstens
Rafael J. Wysocki
Paul Bolle
Joe Lawrence
Myron Stowe