printk is meant to be used with an associated log level. There are some
instances of printk scattered around the mm code where the log level is
missing. Add a log level and adhere to suggestions by
scripts/checkpatch.pl by moving to the pr_* macros.
Also add the typical pr_fmt definition so that print statements can be
easily traced back to the modules where they occur, correlated one with
another, etc. This will require the removal of some (now redundant)
prefixes on a few print statements.
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Trond pointed out, you can currently deadlock yourself by setting a
file-private lock on a file that requires mandatory locking and then
trying to do I/O on it.
Avoid this problem by plumbing some knowledge of file-private locks into
the mandatory locking code. In order to do this, we must pass down
information about the struct file that's being used to
locks_verify_locked.
Reported-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
This patch is a continuation of efforts trying to optimize find_vma(),
avoiding potentially expensive rbtree walks to locate a vma upon faults.
The original approach (https://lkml.org/lkml/2013/11/1/410), where the
largest vma was also cached, ended up being too specific and random,
thus further comparison with other approaches were needed. There are
two things to consider when dealing with this, the cache hit rate and
the latency of find_vma(). Improving the hit-rate does not necessarily
translate in finding the vma any faster, as the overhead of any fancy
caching schemes can be too high to consider.
We currently cache the last used vma for the whole address space, which
provides a nice optimization, reducing the total cycles in find_vma() by
up to 250%, for workloads with good locality. On the other hand, this
simple scheme is pretty much useless for workloads with poor locality.
Analyzing ebizzy runs shows that, no matter how many threads are
running, the mmap_cache hit rate is less than 2%, and in many situations
below 1%.
The proposed approach is to replace this scheme with a small per-thread
cache, maximizing hit rates at a very low maintenance cost.
Invalidations are performed by simply bumping up a 32-bit sequence
number. The only expensive operation is in the rare case of a seq
number overflow, where all caches that share the same address space are
flushed. Upon a miss, the proposed replacement policy is based on the
page number that contains the virtual address in question. Concretely,
the following results are seen on an 80 core, 8 socket x86-64 box:
1) System bootup: Most programs are single threaded, so the per-thread
scheme does improve ~50% hit rate by just adding a few more slots to
the cache.
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 50.61% | 19.90 |
| patched | 73.45% | 13.58 |
+----------------+----------+------------------+
2) Kernel build: This one is already pretty good with the current
approach as we're dealing with good locality.
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 75.28% | 11.03 |
| patched | 88.09% | 9.31 |
+----------------+----------+------------------+
3) Oracle 11g Data Mining (4k pages): Similar to the kernel build workload.
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 70.66% | 17.14 |
| patched | 91.15% | 12.57 |
+----------------+----------+------------------+
4) Ebizzy: There's a fair amount of variation from run to run, but this
approach always shows nearly perfect hit rates, while baseline is just
about non-existent. The amounts of cycles can fluctuate between
anywhere from ~60 to ~116 for the baseline scheme, but this approach
reduces it considerably. For instance, with 80 threads:
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 1.06% | 91.54 |
| patched | 99.97% | 14.18 |
+----------------+----------+------------------+
[akpm@linux-foundation.org: fix nommu build, per Davidlohr]
[akpm@linux-foundation.org: document vmacache_valid() logic]
[akpm@linux-foundation.org: attempt to untangle header files]
[akpm@linux-foundation.org: add vmacache_find() BUG_ON]
[hughd@google.com: add vmacache_valid_mm() (from Oleg)]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: adjust and enhance comments]
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=L+mC
-----END PGP SIGNATURE-----
Merge commit 'v3.10.73' into msm-3.10
This merge brings us up to date with upstream kernel.org tag v3.10.73.
As part of the conflict resolution, changes introduced by commit 72684eae7
("arm64: Fix up /proc/cpuinfo") have been intentionally dropped, as they
conflict with Android changes msm-3.10 kernel to solve the problems
in a different way. Since userspace readers of this file may depend on
the existing msm-3.10 implementation, it's left as-is for now. The
commit may later be introduced if it is found to not impact userspaces
paired with this kernel.
* commit 'v3.10.73' (264 commits):
Linux 3.10.73
target: Allow Write Exclusive non-reservation holders to READ
target: Allow AllRegistrants to re-RESERVE existing reservation
target: Fix R_HOLDER bit usage for AllRegistrants
target/pscsi: Fix NULL pointer dereference in get_device_type
iscsi-target: Avoid early conn_logout_comp for iser connections
target: Fix reference leak in target_get_sess_cmd() error path
ARM: at91: pm: fix at91rm9200 standby
ipvs: rerouting to local clients is not needed anymore
ipvs: add missing ip_vs_pe_put in sync code
powerpc/smp: Wait until secondaries are active & online
x86/vdso: Fix the build on GCC5
x86/fpu: Drop_fpu() should not assume that tsk equals current
x86/fpu: Avoid math_state_restore() without used_math() in __restore_xstate_sig()
crypto: aesni - fix memory usage in GCM decryption
libsas: Fix Kernel Crash in smp_execute_task
xen-pciback: limit guest control of command register
nilfs2: fix deadlock of segment constructor during recovery
regulator: core: Fix enable GPIO reference counting
regulator: Only enable disabled regulators on resume
ALSA: hda - Treat stereo-to-mono mix properly
ALSA: hda - Add workaround for MacBook Air 5,2 built-in mic
ALSA: hda - Set single_adc_amp flag for CS420x codecs
ALSA: hda - Don't access stereo amps for mono channel widgets
ALSA: hda - Fix built-in mic on Compaq Presario CQ60
ALSA: control: Add sanity checks for user ctl id name string
spi: pl022: Fix race in giveback() leading to driver lock-up
tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send
workqueue: fix hang involving racing cancel[_delayed]_work_sync()'s for PREEMPT_NONE
can: add missing initialisations in CAN related skbuffs
Change email address for 8250_pci
virtio_console: init work unconditionally
fuse: notify: don't move pages
fuse: set stolen page uptodate
drm/radeon: drop setting UPLL to sleep mode
drm/radeon: do a posting read in rs600_set_irq
drm/radeon: do a posting read in si_set_irq
drm/radeon: do a posting read in r600_set_irq
drm/radeon: do a posting read in r100_set_irq
drm/radeon: do a posting read in evergreen_set_irq
drm/radeon: fix DRM_IOCTL_RADEON_CS oops
tcp: make connect() mem charging friendly
net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour
tcp: fix tcp fin memory accounting
Revert "net: cx82310_eth: use common match macro"
rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
inet_diag: fix possible overflow in inet_diag_dump_one_icsk()
rds: avoid potential stack overflow
net: sysctl_net_core: check SNDBUF and RCVBUF for min length
sparc64: Fix several bugs in memmove().
sparc: Touch NMI watchdog when walking cpus and calling printk
sparc: perf: Make counting mode actually work
sparc: perf: Remove redundant perf_pmu_{en|dis}able calls
sparc: semtimedop() unreachable due to comparison error
sparc32: destroy_context() and switch_mm() needs to disable interrupts.
Linux 3.10.72
ath5k: fix spontaneus AR5312 freezes
ACPI / video: Load the module even if ACPI is disabled
drm/radeon: fix 1 RB harvest config setup for TN/RL
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered
HID: fixup the conflicting keyboard mappings quirk
HID: input: fix confusion on conflicting mappings
staging: comedi: cb_pcidas64: fix incorrect AI range code handling
dm snapshot: fix a possible invalid memory access on unload
dm: fix a race condition in dm_get_md
dm io: reject unsupported DISCARD requests with EOPNOTSUPP
dm mirror: do not degrade the mirror on discard error
staging: comedi: comedi_compat32.c: fix COMEDI_CMD copy back
clk: sunxi: Support factor clocks with N factor starting not from 0
fixed invalid assignment of 64bit mask to host dma_boundary for scatter gather segment boundary limit.
nilfs2: fix potential memory overrun on inode
IB/qib: Do not write EEPROM
sg: fix read() error reporting
ALSA: hda - Add pin configs for ASUS mobo with IDT 92HD73XX codec
ALSA: pcm: Don't leave PREPARED state after draining
tty: fix up atime/mtime mess, take four
sunrpc: fix braino in ->poll()
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
USB: serial: fix potential use-after-free after failed probe
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
net: irda: fix wait_until_sent poll timeout
xhci: fix reporting of 0-sized URBs in control endpoint
xhci: Allocate correct amount of scratchpad buffers
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: usbfs: don't leak kernel data in siginfo
USB: serial: cp210x: Adding Seletek device id's
KVM: MIPS: Fix trace event to save PC directly
KVM: emulate: fix CMPXCHG8B on 32-bit hosts
Btrfs:__add_inode_ref: out of bounds memory read when looking for extended ref.
Btrfs: fix data loss in the fast fsync path
btrfs: fix lost return value due to variable shadowing
iio: imu: adis16400: Fix sign extension
x86/asm/entry/64: Remove a bogus 'ret_from_fork' optimization
PM / QoS: remove duplicate call to pm_qos_update_target
target: Check for LBA + sectors wrap-around in sbc_parse_cdb
mm/memory.c: actually remap enough memory
mm/compaction: fix wrong order check in compact_finished()
mm/nommu.c: fix arithmetic overflow in __vm_enough_memory()
mm/mmap.c: fix arithmetic overflow in __vm_enough_memory()
mm/hugetlb: add migration entry check in __unmap_hugepage_range
team: don't traverse port list using rcu in team_set_mac_address
udp: only allow UFO for packets from SOCK_DGRAM sockets
usb: plusb: Add support for National Instruments host-to-host cable
macvtap: make sure neighbour code can push ethernet header
net: compat: Ignore MSG_CMSG_COMPAT in compat_sys_{send, recv}msg
team: fix possible null pointer dereference in team_handle_frame
net: reject creation of netdev names with colons
ematch: Fix auto-loading of ematch modules.
net: phy: Fix verification of EEE support in phy_init_eee
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
ipv4: ip_check_defrag should correctly check return value of skb_copy_bits
gen_stats.c: Duplicate xstats buffer for later use
rtnetlink: call ->dellink on failure when ->newlink exists
ipv6: fix ipv6_cow_metrics for non DST_HOST case
rtnetlink: ifla_vf_policy: fix misuses of NLA_BINARY
Linux 3.10.71
libceph: fix double __remove_osd() problem
libceph: change from BUG to WARN for __remove_osd() asserts
libceph: assert both regular and lingering lists in __remove_osd()
MIPS: Export FP functions used by lose_fpu(1) for KVM
x86, mm/ASLR: Fix stack randomization on 64-bit systems
blk-throttle: check stats_cpu before reading it from sysfs
jffs2: fix handling of corrupted summary length
md/raid1: fix read balance when a drive is write-mostly.
md/raid5: Fix livelock when array is both resyncing and degraded.
metag: Fix KSTK_EIP() and KSTK_ESP() macros
gpio: tps65912: fix wrong container_of arguments
arm64: compat Fix siginfo_t -> compat_siginfo_t conversion on big endian
hx4700: regulator: declare full constraints
KVM: x86: update masterclock values on TSC writes
KVM: MIPS: Don't leak FPU/DSP to guest
ARC: fix page address calculation if PAGE_OFFSET != LINUX_LINK_BASE
ntp: Fixup adjtimex freq validation on 32-bit systems
kdb: fix incorrect counts in KDB summary command output
ARM: pxa: add regulator_has_full_constraints to poodle board file
ARM: pxa: add regulator_has_full_constraints to corgi board file
vt: provide notifications on selection changes
usb: core: buffer: smallest buffer should start at ARCH_DMA_MINALIGN
USB: fix use-after-free bug in usb_hcd_unlink_urb()
USB: cp210x: add ID for RUGGEDCOM USB Serial Console
tty: Prevent untrappable signals from malicious program
axonram: Fix bug in direct_access
cfq-iosched: fix incorrect filing of rt async cfqq
cfq-iosched: handle failure of cfq group allocation
iscsi-target: Drop problematic active_ts_list usage
NFSv4.1: Fix a kfree() of uninitialised pointers in decode_cb_sequence_args
Added Little Endian support to vtpm module
tpm/tpm_i2c_stm_st33: Fix potential bug in tpm_stm_i2c_send
tpm: Fix NULL return in tpm_ibmvtpm_get_desired_dma
tpm_tis: verify interrupt during init
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
tracing: Fix unmapping loop in tracing_mark_write
MIPS: KVM: Deliver guest interrupts after local_irq_disable()
nfs: don't call blocking operations while !TASK_RUNNING
mmc: sdhci-pxav3: fix setting of pdata->clk_delay_cycles
power_supply: 88pm860x: Fix leaked power supply on probe fail
ALSA: hdspm - Constrain periods to 2 on older cards
ALSA: off by one bug in snd_riptide_joystick_probe()
lmedm04: Fix usb_submit_urb BOGUS urb xfer, pipe 1 != type 3 in interrupt urb
cpufreq: speedstep-smi: enable interrupts when waiting
PCI: Fix infinite loop with ROM image of size 0
PCI: Generate uppercase hex for modalias var in uevent
HID: i2c-hid: Limit reads to wMaxInputLength bytes for input events
iwlwifi: mvm: always use mac color zero
iwlwifi: mvm: fix failure path when power_update fails in add_interface
iwlwifi: mvm: validate tid and sta_id in ba_notif
iwlwifi: pcie: disable the SCD_BASE_ADDR when we resume from WoWLAN
fsnotify: fix handling of renames in audit
xfs: set superblock buffer type correctly
xfs: inode unlink does not set AGI buffer type
xfs: ensure buffer types are set correctly
Bluetooth: ath3k: workaround the compatibility issue with xHCI controller
Linux 3.10.70
rbd: drop an unsafe assertion
media/rc: Send sync space information on the lirc device
net: sctp: fix passing wrong parameter header to param_type2af in sctp_process_param
ppp: deflate: never return len larger than output buffer
ipv4: tcp: get rid of ugly unicast_sock
tcp: ipv4: initialize unicast_sock sk_pacing_rate
bridge: dont send notification when skb->len == 0 in rtnl_bridge_notify
ipv6: replacing a rt6_info needs to purge possible propagated rt6_infos too
ping: Fix race in free in receive path
udp_diag: Fix socket skipping within chain
ipv4: try to cache dst_entries which would cause a redirect
net: sctp: fix slab corruption from use after free on INIT collisions
netxen: fix netxen_nic_poll() logic
ipv6: stop sending PTB packets for MTU < 1280
net: rps: fix cpu unplug
ip: zero sockaddr returned on error queue
Linux 3.10.69
crypto: crc32c - add missing crypto module alias
x86,kvm,vmx: Preserve CR4 across VM entry
kvm: vmx: handle invvpid vm exit gracefully
smpboot: Add missing get_online_cpus() in smpboot_register_percpu_thread()
ALSA: ak411x: Fix stall in work callback
ASoC: sgtl5000: add delay before first I2C access
ASoC: atmel_ssc_dai: fix start event for I2S mode
lib/checksum.c: fix build for generic csum_tcpudp_nofold
ext4: prevent bugon on race between write/fcntl
arm64: Fix up /proc/cpuinfo
nilfs2: fix deadlock of segment constructor over I_SYNC flag
lib/checksum.c: fix carry in csum_tcpudp_nofold
mm: pagewalk: call pte_hole() for VM_PFNMAP during walk_page_range
MIPS: Fix kernel lockup or crash after CPU offline/online
MIPS: IRQ: Fix disable_irq on CPU IRQs
PCI: Add NEC variants to Stratus ftServer PCIe DMI check
gpio: sysfs: fix memory leak in gpiod_sysfs_set_active_low
gpio: sysfs: fix memory leak in gpiod_export_link
Linux 3.10.68
target: Drop arbitrary maximum I/O size limit
iser-target: Fix implicit termination of connections
iser-target: Handle ADDR_CHANGE event for listener cm_id
iser-target: Fix connected_handler + teardown flow race
iser-target: Parallelize CM connection establishment
iser-target: Fix flush + disconnect completion handling
iscsi,iser-target: Initiate termination only once
vhost-scsi: Add missing virtio-scsi -> TCM attribute conversion
tcm_loop: Fix wrong I_T nexus association
vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINT
ib_isert: Add max_send_sge=2 minimum for control PDU responses
IB/isert: Adjust CQ size to HW limits
workqueue: fix subtle pool management issue which can stall whole worker_pool
gpio: squelch a compiler warning
efi-pstore: Make efi-pstore return a unique id
pstore/ram: avoid atomic accesses for ioremapped regions
pstore: Fix NULL pointer fault if get NULL prz in ramoops_get_next_prz
pstore: skip zero size persistent ram buffer in traverse
pstore: clarify clearing of _read_cnt in ramoops_context
pstore: d_alloc_name() doesn't return an ERR_PTR
pstore: Fail to unlink if a driver has not defined pstore_erase
ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE
ARM: 8108/1: mm: Introduce {pte,pmd}_isset and {pte,pmd}_isclear
ARM: DMA: ensure that old section mappings are flushed from the TLB
ARM: 7931/1: Correct virt_addr_valid
ARM: fix asm/memory.h build error
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: lpae: fix definition of PTE_HWTABLE_PTRS
ARM: fix type of PHYS_PFN_OFFSET to unsigned long
ARM: LPAE: use phys_addr_t in alloc_init_pud()
ARM: LPAE: use signed arithmetic for mask definitions
ARM: mm: correct pte_same behaviour for LPAE.
ARM: 7829/1: Add ".text.unlikely" and ".text.hot" to arm unwind tables
drivers: net: cpsw: discard dual emac default vlan configuration
regulator: core: fix race condition in regulator_put()
spi/pxa2xx: Clear cur_chip pointer before starting next message
dm cache: fix missing ERR_PTR returns and handling
dm thin: don't allow messages to be sent to a pool target in READ_ONLY or FAIL mode
nl80211: fix per-station group key get/del and memory leak
NFSv4.1: Fix an Oops in nfs41_walk_client_list
nfs: fix dio deadlock when O_DIRECT flag is flipped
Input: i8042 - add noloop quirk for Medion Akoya E7225 (MD98857)
ALSA: seq-dummy: remove deadlock-causing events on close
powerpc/xmon: Fix another endiannes issue in RTAS call from xmon
can: kvaser_usb: Fix state handling upon BUS_ERROR events
can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT
can: kvaser_usb: Send correct context to URB completion
can: kvaser_usb: Do not sleep in atomic context
ASoC: wm8960: Fix capture sample rate from 11250 to 11025
spi: dw-mid: fix FIFO size
Signed-off-by: Ian Maund <imaund@codeaurora.org>
commit 8138a67a5557ffea3a21dfd6f037842d4e748513 upstream.
I noticed that "allowed" can easily overflow by falling below 0, because
(total_vm / 32) can be larger than "allowed". The problem occurs in
OVERCOMMIT_NONE mode.
In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode). All subsequent allocations will fall
(system-wide), so system become unusable.
The problem was masked out by commit c9b1d0981f
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory
It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.
Fix this issue by switching to signed arithmetic here.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since all architectures have been converted to use vm_unmapped_area(),
there is no remaining use for the free_area_cache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Git-commit: 98d1e64f95b177d0f14efbdf695a1b28e1428035
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
Signed-off-by: Ian Maund <imaund@codeaurora.org>
Pull compat cleanup from Al Viro:
"Mostly about syscall wrappers this time; there will be another pile
with patches in the same general area from various people, but I'd
rather push those after both that and vfs.git pile are in."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
syscalls.h: slightly reduce the jungles of macros
get rid of union semop in sys_semctl(2) arguments
make do_mremap() static
sparc: no need to sign-extend in sync_file_range() wrapper
ppc compat wrappers for add_key(2) and request_key(2) are pointless
x86: trim sys_ia32.h
x86: sys32_kill and sys32_mprotect are pointless
get rid of compat_sys_semctl() and friends in case of ARCH_WANT_OLD_COMPAT_IPC
merge compat sys_ipc instances
consolidate compat lookup_dcookie()
convert vmsplice to COMPAT_SYSCALL_DEFINE
switch getrusage() to COMPAT_SYSCALL_DEFINE
switch epoll_pwait to COMPAT_SYSCALL_DEFINE
convert sendfile{,64} to COMPAT_SYSCALL_DEFINE
switch signalfd{,4}() to COMPAT_SYSCALL_DEFINE
make SYSCALL_DEFINE<n>-generated wrappers do asmlinkage_protect
make HAVE_SYSCALL_WRAPPERS unconditional
consolidate cond_syscall and SYSCALL_ALIAS declarations
teach SYSCALL_DEFINE<n> how to deal with long long/unsigned long long
get rid of duplicate logics in __SC_....[1-6] definitions
Add an admin_reserve_kbytes knob to allow admins to change the hardcoded
memory reserve to something other than 3%, which may be multiple
gigabytes on large memory systems. Only about 8MB is necessary to
enable recovery in the default mode, and only a few hundred MB are
required even when overcommit is disabled.
This affects OVERCOMMIT_GUESS and OVERCOMMIT_NEVER.
admin_reserve_kbytes is initialized to min(3% free pages, 8MB)
I arrived at 8MB by summing the RSS of sshd or login, bash, and top.
Please see first patch in this series for full background, motivation,
testing, and full changelog.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make init_admin_reserve() static]
Signed-off-by: Andrew Shewmaker <agshew@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add user_reserve_kbytes knob.
Limit the growth of the memory reserved for other user processes to
min(3% current process size, user_reserve_pages). Only about 8MB is
necessary to enable recovery in the default mode, and only a few hundred
MB are required even when overcommit is disabled.
user_reserve_pages defaults to min(3% free pages, 128MB)
I arrived at 128MB by taking the max VSZ of sshd, login, bash, and top ...
then adding the RSS of each.
This only affects OVERCOMMIT_NEVER mode.
Background
1. user reserve
__vm_enough_memory reserves a hardcoded 3% of the current process size for
other applications when overcommit is disabled. This was done so that a
user could recover if they launched a memory hogging process. Without the
reserve, a user would easily run into a message such as:
bash: fork: Cannot allocate memory
2. admin reserve
Additionally, a hardcoded 3% of free memory is reserved for root in both
overcommit 'guess' and 'never' modes. This was intended to prevent a
scenario where root-cant-log-in and perform recovery operations.
Note that this reserve shrinks, and doesn't guarantee a useful reserve.
Motivation
The two hardcoded memory reserves should be updated to account for current
memory sizes.
Also, the admin reserve would be more useful if it didn't shrink too much.
When the current code was originally written, 1GB was considered
"enterprise". Now the 3% reserve can grow to multiple GB on large memory
systems, and it only needs to be a few hundred MB at most to enable a user
or admin to recover a system with an unwanted memory hogging process.
I've found that reducing these reserves is especially beneficial for a
specific type of application load:
* single application system
* one or few processes (e.g. one per core)
* allocating all available memory
* not initializing every page immediately
* long running
I've run scientific clusters with this sort of load. A long running job
sometimes failed many hours (weeks of CPU time) into a calculation. They
weren't initializing all of their memory immediately, and they weren't
using calloc, so I put systems into overcommit 'never' mode. These
clusters run diskless and have no swap.
However, with the current reserves, a user wishing to allocate as much
memory as possible to one process may be prevented from using, for
example, almost 2GB out of 32GB.
The effect is less, but still significant when a user starts a job with
one process per core. I have repeatedly seen a set of processes
requesting the same amount of memory fail because one of them could not
allocate the amount of memory a user would expect to be able to allocate.
For example, Message Passing Interfce (MPI) processes, one per core. And
it is similar for other parallel programming frameworks.
Changing this reserve code will make the overcommit never mode more useful
by allowing applications to allocate nearly all of the available memory.
Also, the new admin_reserve_kbytes will be safer than the current behavior
since the hardcoded 3% of available memory reserve can shrink to something
useless in the case where applications have grabbed all available memory.
Risks
* "bash: fork: Cannot allocate memory"
The downside of the first patch-- which creates a tunable user reserve
that is only used in overcommit 'never' mode--is that an admin can set
it so low that a user may not be able to kill their process, even if
they already have a shell prompt.
Of course, a user can get in the same predicament with the current 3%
reserve--they just have to launch processes until 3% becomes negligible.
* root-cant-log-in problem
The second patch, adding the tunable rootuser_reserve_pages, allows
the admin to shoot themselves in the foot by setting it too small. They
can easily get the system into a state where root-can't-log-in.
However, the new admin_reserve_kbytes will be safer than the current
behavior since the hardcoded 3% of available memory reserve can shrink
to something useless in the case where applications have grabbed all
available memory.
Alternatives
* Memory cgroups provide a more flexible way to limit application memory.
Not everyone wants to set up cgroups or deal with their overhead.
* We could create a fourth overcommit mode which provides smaller reserves.
The size of useful reserves may be drastically different depending
on the whether the system is embedded or enterprise.
* Force users to initialize all of their memory or use calloc.
Some users don't want/expect the system to overcommit when they malloc.
Overcommit 'never' mode is for this scenario, and it should work well.
The new user and admin reserve tunables are simple to use, with low
overhead compared to cgroups. The patches preserve current behavior where
3% of memory is less than 128MB, except that the admin reserve doesn't
shrink to an unusable size under pressure. The code allows admins to tune
for embedded and enterprise usage.
FAQ
* How is the root-cant-login problem addressed?
What happens if admin_reserve_pages is set to 0?
Root is free to shoot themselves in the foot by setting
admin_reserve_kbytes too low.
On x86_64, the minimum useful reserve is:
8MB for overcommit 'guess'
128MB for overcommit 'never'
admin_reserve_pages defaults to min(3% free memory, 8MB)
So, anyone switching to 'never' mode needs to adjust
admin_reserve_pages.
* How do you calculate a minimum useful reserve?
A user or the admin needs enough memory to login and perform
recovery operations, which includes, at a minimum:
sshd or login + bash (or some other shell) + top (or ps, kill, etc.)
For overcommit 'guess', we can sum resident set sizes (RSS)
because we only need enough memory to handle what the recovery
programs will typically use. On x86_64 this is about 8MB.
For overcommit 'never', we can take the max of their virtual sizes (VSZ)
and add the sum of their RSS. We use VSZ instead of RSS because mode
forces us to ensure we can fulfill all of the requested memory allocations--
even if the programs only use a fraction of what they ask for.
On x86_64 this is about 128MB.
When swap is enabled, reserves are useful even when they are as
small as 10MB, regardless of overcommit mode.
When both swap and overcommit are disabled, then the admin should
tune the reserves higher to be absolutley safe. Over 230MB each
was safest in my testing.
* What happens if user_reserve_pages is set to 0?
Note, this only affects overcomitt 'never' mode.
Then a user will be able to allocate all available memory minus
admin_reserve_kbytes.
However, they will easily see a message such as:
"bash: fork: Cannot allocate memory"
And they won't be able to recover/kill their application.
The admin should be able to recover the system if
admin_reserve_kbytes is set appropriately.
* What's the difference between overcommit 'guess' and 'never'?
"Guess" allows an allocation if there are enough free + reclaimable
pages. It has a hardcoded 3% of free pages reserved for root.
"Never" allows an allocation if there is enough swap + a configurable
percentage (default is 50) of physical RAM. It has a hardcoded 3% of
free pages reserved for root, like "Guess" mode. It also has a
hardcoded 3% of the current process size reserved for additional
applications.
* Why is overcommit 'guess' not suitable even when an app eventually
writes to every page? It takes free pages, file pages, available
swap pages, reclaimable slab pages into consideration. In other words,
these are all pages available, then why isn't overcommit suitable?
Because it only looks at the present state of the system. It
does not take into account the memory that other applications have
malloced, but haven't initialized yet. It overcommits the system.
Test Summary
There was little change in behavior in the default overcommit 'guess'
mode with swap enabled before and after the patch. This was expected.
Systems run most predictably (i.e. no oom kills) in overcommit 'never'
mode with swap enabled. This also allowed the most memory to be allocated
to a user application.
Overcommit 'guess' mode without swap is a bad idea. It is easy to
crash the system. None of the other tested combinations crashed.
This matches my experience on the Roadrunner supercomputer.
Without the tunable user reserve, a system in overcommit 'never' mode
and without swap does not allow the admin to recover, although the
admin can.
With the new tunable reserves, a system in overcommit 'never' mode
and without swap can be configured to:
1. maximize user-allocatable memory, running close to the edge of
recoverability
2. maximize recoverability, sacrificing allocatable memory to
ensure that a user cannot take down a system
Test Description
Fedora 18 VM - 4 x86_64 cores, 5725MB RAM, 4GB Swap
System is booted into multiuser console mode, with unnecessary services
turned off. Caches were dropped before each test.
Hogs are user memtester processes that attempt to allocate all free memory
as reported by /proc/meminfo
In overcommit 'never' mode, memory_ratio=100
Test Results
3.9.0-rc1-mm1
Overcommit | Swap | Hogs | MB Got/Wanted | OOMs | User Recovery | Admin Recovery
---------- ---- ---- ------------- ---- ------------- --------------
guess yes 1 5432/5432 no yes yes
guess yes 4 5444/5444 1 yes yes
guess no 1 5302/5449 no yes yes
guess no 4 - crash no no
never yes 1 5460/5460 1 yes yes
never yes 4 5460/5460 1 yes yes
never no 1 5218/5432 no no yes
never no 4 5203/5448 no no yes
3.9.0-rc1-mm1-tunablereserves
User and Admin Recovery show their respective reserves, if applicable.
Overcommit | Swap | Hogs | MB Got/Wanted | OOMs | User Recovery | Admin Recovery
---------- ---- ---- ------------- ---- ------------- --------------
guess yes 1 5419/5419 no - yes 8MB yes
guess yes 4 5436/5436 1 - yes 8MB yes
guess no 1 5440/5440 * - yes 8MB yes
guess no 4 - crash - no 8MB no
* process would successfully mlock, then the oom killer would pick it
never yes 1 5446/5446 no 10MB yes 20MB yes
never yes 4 5456/5456 no 10MB yes 20MB yes
never no 1 5387/5429 no 128MB no 8MB barely
never no 1 5323/5428 no 226MB barely 8MB barely
never no 1 5323/5428 no 226MB barely 8MB barely
never no 1 5359/5448 no 10MB no 10MB barely
never no 1 5323/5428 no 0MB no 10MB barely
never no 1 5332/5428 no 0MB no 50MB yes
never no 1 5293/5429 no 0MB no 90MB yes
never no 1 5001/5427 no 230MB yes 338MB yes
never no 4* 4998/5424 no 230MB yes 338MB yes
* more memtesters were launched, able to allocate approximately another 100MB
Future Work
- Test larger memory systems.
- Test an embedded image.
- Test other architectures.
- Time malloc microbenchmarks.
- Would it be useful to be able to set overcommit policy for
each memory cgroup?
- Some lines are slightly above 80 chars.
Perhaps define a macro to convert between pages and kb?
Other places in the kernel do this.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make init_user_reserve() static]
Signed-off-by: Andrew Shewmaker <agshew@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although our intention is to unexport internal structure entirely, but
there is one exception for kexec. kexec dumps address of vmlist and
makedumpfile uses this information.
We are about to remove vmlist, then another way to retrieve information
of vmalloc layer is needed for makedumpfile. For this purpose, we
export vmap_area_list, instead of vmlist.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Anderson <anderson@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I think we could just move the full vm_iomap_memory() function into
util.h or similar, but I didn't get any reply from anybody actually
using nommu even to this trivial patch, so I'm not going to touch it any
more than required.
Here's the fairly minimal stub to make the nommu case at least
potentially work. It doesn't seem like anybody cares, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_vma() can be called by multiple threads with read lock
held on mm->mmap_sem and any of them can update mm->mmap_cache.
Prevent compiler from re-fetching mm->mmap_cache, because other
readers could update it in the meantime:
thread 1 thread 2
|
find_vma() | find_vma()
struct vm_area_struct *vma = NULL; |
vma = mm->mmap_cache; |
if (!(vma && vma->vm_end > addr |
&& vma->vm_start <= addr)) { |
| mm->mmap_cache = vma;
return vma; |
^^ compiler may optimize this |
local variable out and re-read |
mm->mmap_cache |
This issue can be reproduced with gcc-4.8.0-1 on s390x by running
mallocstress testcase from LTP, which triggers:
kernel BUG at mm/rmap.c:1088!
Call Trace:
([<000003d100c57000>] 0x3d100c57000)
[<000000000023a1c0>] do_wp_page+0x2fc/0xa88
[<000000000023baae>] handle_pte_fault+0x41a/0xac8
[<000000000023d832>] handle_mm_fault+0x17a/0x268
[<000000000060507a>] do_protection_exception+0x1e2/0x394
[<0000000000603a04>] pgm_check_handler+0x138/0x13c
[<000003fffcf1f07a>] 0x3fffcf1f07a
Last Breaking-Event-Address:
[<000000000024755e>] page_add_new_anon_rmap+0xc2/0x168
Thanks to Jakub Jelinek for his insight on gcc and helping to
track this down.
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The extern in sys_sparc_64.c was a rudiment of time when do_mremap()
used to exist in MMU case (it doesn't anymore). As for !MMU one,
nothing uses it outside of mm/nommu.c...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
This change adds a follow_page_mask function which is equivalent to
follow_page, but with an extra page_mask argument.
follow_page_mask sets *page_mask to HPAGE_PMD_NR - 1 when it encounters
a THP page, and to 0 in other cases.
__get_user_pages() makes use of this in order to accelerate populating
THP ranges - that is, when both the pages and vmas arrays are NULL, we
don't need to iterate HPAGE_PMD_NR times to cover a single THP page (and
we also avoid taking mm->page_table_lock that many times).
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use long type for page counts in mm_populate() so as to avoid integer
overflow when running the following test code:
int main(void) {
void *p = mmap(NULL, 0x100000000000, PROT_READ,
MAP_PRIVATE | MAP_ANON, -1, 0);
printf("p: %p\n", p);
mlockall(MCL_CURRENT);
printf("done\n");
return 0;
}
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swap_lock is heavily contended when I test swap to 3 fast SSD (even
slightly slower than swap to 2 such SSD). The main contention comes
from swap_info_get(). This patch tries to fix the gap with adding a new
per-partition lock.
Global data like nr_swapfiles, total_swap_pages, least_priority and
swap_list are still protected by swap_lock.
nr_swap_pages is an atomic now, it can be changed without swap_lock. In
theory, it's possible get_swap_page() finds no swap pages but actually
there are free swap pages. But sounds not a big problem.
Accessing partition specific data (like scan_swap_map and so on) is only
protected by swap_info_struct.lock.
Changing swap_info_struct.flags need hold swap_lock and
swap_info_struct.lock, because scan_scan_map() will check it. read the
flags is ok with either the locks hold.
If both swap_lock and swap_info_struct.lock must be hold, we always hold
the former first to avoid deadlock.
swap_entry_free() can change swap_list. To delete that code, we add a
new highest_priority_index. Whenever get_swap_page() is called, we
check it. If it's valid, we use it.
It's a pity get_swap_page() still holds swap_lock(). But in practice,
swap_lock() isn't heavily contended in my test with this patch (or I can
say there are other much more heavier bottlenecks like TLB flush). And
BTW, looks get_swap_page() doesn't really need the lock. We never free
swap_info[] and we check SWAP_WRITEOK flag. The only risk without the
lock is we could swapout to some low priority swap, but we can quickly
recover after several rounds of swap, so sounds not a big deal to me.
But I'd prefer to fix this if it's a real problem.
"swap: make each swap partition have one address_space" improved the
swapout speed from 1.7G/s to 2G/s. This patch further improves the
speed to 2.3G/s, so around 15% improvement. It's a multi-process test,
so TLB flush isn't the biggest bottleneck before the patches.
[arnd@arndb.de: fix it for nommu]
[hughd@google.com: add missing unlock]
[minchan@kernel.org: get rid of lockdep whinge on sys_swapon]
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_mmap_pgoff() rounds up the desired size to the next PAGE_SIZE
multiple, however there was no equivalent code in mm_populate(), which
caused issues.
This could be fixed by introduced the same rounding in mm_populate(),
however I think it's preferable to make do_mmap_pgoff() return populate
as a size rather than as a boolean, so we don't have to duplicate the
size rounding logic in mm_populate().
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When creating new mappings using the MAP_POPULATE / MAP_LOCKED flags (or
with MCL_FUTURE in effect), we want to populate the pages within the
newly created vmas. This may take a while as we may have to read pages
from disk, so ideally we want to do this outside of the write-locked
mmap_sem region.
This change introduces mm_populate(), which is used to defer populating
such mappings until after the mmap_sem write lock has been released.
This is implemented as a generalization of the former do_mlock_pages(),
which accomplished the same task but was using during mlock() /
mlockall().
Signed-off-by: Michel Lespinasse <walken@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the sysctl-related bits from include/linux/sched.h into
a new file: include/linux/sched/sysctl.h. Then update source
files requiring access to those bits by including the new
header file.
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094659.06dced96@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It will be useful to be able to access global memory commitment from
device drivers. On the Hyper-V platform, the host has a policy engine to
balance the available physical memory amongst all competing virtual
machines hosted on a given node. This policy engine is driven by a number
of metrics including the memory commitment reported by the guests. The
balloon driver for Linux on Hyper-V will use this function to retrieve
guest memory commitment. This function is also used in Xen self
ballooning code.
[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement an interval tree as a replacement for the VMA prio_tree. The
algorithms are similar to lib/interval_tree.c; however that code can't be
directly reused as the interval endpoints are not explicitly stored in the
VMA. So instead, the common algorithm is moved into a template and the
details (node type, how to get interval endpoints from the node, etc) are
filled in using the C preprocessor.
Once the interval tree functions are available, using them as a
replacement to the VMA prio tree is a relatively simple, mechanical job.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the kernel sets mm->exe_file during sys_execve() and then tracks
number of vmas with VM_EXECUTABLE flag in mm->num_exe_file_vmas, as soon
as this counter drops to zero kernel resets mm->exe_file to NULL. Plus it
resets mm->exe_file at last mmput() when mm->mm_users drops to zero.
VMA with VM_EXECUTABLE flag appears after mapping file with flag
MAP_EXECUTABLE, such vmas can appears only at sys_execve() or after vma
splitting, because sys_mmap ignores this flag. Usually binfmt module sets
mm->exe_file and mmaps executable vmas with this file, they hold
mm->exe_file while task is running.
comment from v2.6.25-6245-g925d1c4 ("procfs task exe symlink"),
where all this stuff was introduced:
> The kernel implements readlink of /proc/pid/exe by getting the file from
> the first executable VMA. Then the path to the file is reconstructed and
> reported as the result.
>
> Because of the VMA walk the code is slightly different on nommu systems.
> This patch avoids separate /proc/pid/exe code on nommu systems. Instead of
> walking the VMAs to find the first executable file-backed VMA we store a
> reference to the exec'd file in the mm_struct.
>
> That reference would prevent the filesystem holding the executable file
> from being unmounted even after unmapping the VMAs. So we track the number
> of VM_EXECUTABLE VMAs and drop the new reference when the last one is
> unmapped. This avoids pinning the mounted filesystem.
exe_file's vma accounting is hooked into every file mmap/unmmap and vma
split/merge just to fix some hypothetical pinning fs from umounting by mm,
which already unmapped all its executable files, but still alive.
Seems like currently nobody depends on this behaviour. We can try to
remove this logic and keep mm->exe_file until final mmput().
mm->exe_file is still protected with mm->mmap_sem, because we want to
change it via new sys_prctl(PR_SET_MM_EXE_FILE). Also via this syscall
task can change its mm->exe_file and unpin mountpoint explicitly.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move actual pte filling for non-linear file mappings into the new special
vma operation: ->remap_pages().
Filesystems must implement this method to get non-linear mapping support,
if it uses filemap_fault() then generic_file_remap_pages() can be used.
Now device drivers can implement this method and obtain nonlinear vma support.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com> #arch/tile
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compiling 3.5-rc1 for nommu targets gives:
CC mm/nommu.o
mm/nommu.c: In function ‘sys_mmap_pgoff’:
mm/nommu.c:1489:2: error: ‘ret’ undeclared (first use in this function)
mm/nommu.c:1489:2: note: each undeclared identifier is reported only once for each function it appears in
It is trivially fixed by replacing 'ret' with the local variable that is
already defined for the return value 'retval'.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
take it to mm/util.c, convert vm_mmap() to use of that one and
take it to mm/util.c as well, convert both sys_mmap_pgoff() to
use of vm_mmap_pgoff()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like the vm_brk() function, this is the same as "do_munmap()", except it
does the VM locking for the caller.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It does the same thing as "do_brk()", except it handles the VM locking
too.
It turns out that all external callers want that anyway, so we can make
do_brk() static to just mm/mmap.c while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't clear vm_mm in a deleted VMA as it's unnecessary and might
conceivably break the filesystem or driver VMA close routine.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lock i_mmap_mutex for access to the VMA prio list to prevent concurrent
access. Currently, certain parts of the mmap handling are protected by
the region mutex, but not all.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When mapping a foreign page with xenbus_map_ring_valloc() with the
GNTTABOP_map_grant_ref hypercall, set the GNTMAP_contains_pte flag and
pass a pointer to the PTE (in init_mm).
After the page is mapped, the usual fault mechanism can be used to
update additional MMs. This allows the vmalloc_sync_all() to be
removed from alloc_vm_area().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
[v1: Squashed fix by Michal for no-mmu case]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The files changed within are only using the EXPORT_SYMBOL
macro variants. They are not using core modular infrastructure
and hence don't need module.h but only the export.h header.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
- shmem pages are not immediately available, but they are not
potentially available either, even if we swap them out, they will just
relocate from memory into swap, total amount of immediate and
potentially available memory is not going to be affected, so we
shouldn't count them as potentially free in the first place.
- nr_free_pages() is not an expensive operation anymore, there is no
need to split the decision making in two halves and repeat code.
Signed-off-by: Dmitry Fink <dmitry.fink@palm.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'ptrace' of git://git.kernel.org/pub/scm/linux/kernel/git/oleg/misc: (39 commits)
ptrace: do_wait(traced_leader_killed_by_mt_exec) can block forever
ptrace: fix ptrace_signal() && STOP_DEQUEUED interaction
connector: add an event for monitoring process tracers
ptrace: dont send SIGSTOP on auto-attach if PT_SEIZED
ptrace: mv send-SIGSTOP from do_fork() to ptrace_init_task()
ptrace_init_task: initialize child->jobctl explicitly
has_stopped_jobs: s/task_is_stopped/SIGNAL_STOP_STOPPED/
ptrace: make former thread ID available via PTRACE_GETEVENTMSG after PTRACE_EVENT_EXEC stop
ptrace: wait_consider_task: s/same_thread_group/ptrace_reparented/
ptrace: kill real_parent_is_ptracer() in in favor of ptrace_reparented()
ptrace: ptrace_reparented() should check same_thread_group()
redefine thread_group_leader() as exit_signal >= 0
do not change dead_task->exit_signal
kill task_detached()
reparent_leader: check EXIT_DEAD instead of task_detached()
make do_notify_parent() __must_check, update the callers
__ptrace_detach: avoid task_detached(), check do_notify_parent()
kill tracehook_notify_death()
make do_notify_parent() return bool
ptrace: s/tracehook_tracer_task()/ptrace_parent()/
...
remap_pfn_range() means map physical address pfn<<PAGE_SHIFT to user addr.
For nommu arch it's implemented by vma->vm_start = pfn << PAGE_SHIFT which
is wrong acroding the original meaning of this function. And some driver
developer using remap_pfn_range() with correct parameter will get
unexpected result because vm_start is changed. It should be implementd
like addr = pfn << PAGE_SHIFT but which is meanless on nommu arch, this
patch just make it simply return.
Parameter name and setting of vma->vm_flags also be fixed.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At this point, tracehooks aren't useful to mainline kernel and mostly
just add an extra layer of obfuscation. Although they have comments,
without actual in-kernel users, it is difficult to tell what are their
assumptions and they're actually trying to achieve. To mainline
kernel, they just aren't worth keeping around.
This patch kills the following trivial tracehooks.
* Ones testing whether task is ptraced. Replace with ->ptrace test.
tracehook_expect_breakpoints()
tracehook_consider_ignored_signal()
tracehook_consider_fatal_signal()
* ptrace_event() wrappers. Call directly.
tracehook_report_exec()
tracehook_report_exit()
tracehook_report_vfork_done()
* ptrace_release_task() wrapper. Call directly.
tracehook_finish_release_task()
* noop
tracehook_prepare_release_task()
tracehook_report_death()
This doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Currently on nommu arch mmap(),mremap() and munmap() doesn't do
page_align() which isn't consist with mmu arch and cause some issues.
First, some drivers' mmap() function depends on vma->vm_end - vma->start
is page aligned which is true on mmu arch but not on nommu. eg: uvc
camera driver.
Second munmap() may return -EINVAL[split file] error in cases when end is
not page aligned(passed into from userspace) but vma->vm_end is aligned
dure to split or driver's mmap() ops.
Add page alignment to fix those issues.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because 'ret' is declared as int, not unsigned long, no need to cast the
error contants into unsigned long. If you compile this code on a 64-bit
machine somehow, you'll see following warning:
CC mm/nommu.o
mm/nommu.c: In function `do_mmap_pgoff':
mm/nommu.c:1411: warning: overflow in implicit constant conversion
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If f_op->read() fails and sysctl_nr_trim_pages > 1, there could be a
memory leak between @region->vm_end and @region->vm_top.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mitchel Humpherys
Jeff Layton
Steven Miao
Davidlohr Bueso
Ian Maund
Roman Gushchin
Michel Lespinasse
Linus Torvalds
Andrew Shewmaker
Joonsoo Kim
Jan Stancek
Al Viro
Shaohua Li
Clark Williams
K. Y. Srinivasan
Konstantin Khlebnikov
Greg Ungerer
David Howells
David Vrabel
Paul Gortmaker
Dmitry Fink
Bob Liu
Tejun Heo
Namhyung Kim