commit ab499db80fcf07c18e4053f91a619500f663e90e upstream.
There was a possible race between
ieee80211_reconfig() and
ieee80211_delayed_tailroom_dec(). This could
result in inability to transmit data if driver
crashed during roaming or rekeying and subsequent
skbs with insufficient tailroom appeared.
This race was probably never seen in the wild
because a device driver would have to crash AND
recover within 0.5s which is very unlikely.
I was able to prove this race exists after
changing the delay to 10s locally and crashing
ath10k via debugfs immediately after GTK
rekeying. In case of ath10k the counter went below
0. This was harmless but other drivers which
actually require tailroom (e.g. for WEP ICV or
MMIC) could end up with the counter at 0 instead
of >0 and introduce insufficient skb tailroom
failures because mac80211 would not resize skbs
appropriately anymore.
Fixes: 8d1f7ecd2a ("mac80211: defer tailroom counter manipulation when roaming")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 764152ff66f4a8be1f9d7981e542ffdaa5bd7aff upstream.
Their power value is initialized to zero. This patch fixes an issue
where the configured power drops to the minimum value when AP_VLAN
interfaces are created/removed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that monitor interfaces by default would start on 5GHz
while STA/AP ones would start 2GHZ - It stems from the fact that
ieee80211_register_hw unnecessarily adjusts the local->monitor_chandef
for each band.
This avoids this and while at it uses a single dflt_chandef to initialize
in one go local->{hw.conf.chandef,_oper_chandef,monitor_chandef}
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible since the global hw config and local switched to
cfg80211_chan_def.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 currently sets uAPSD parameters to have VO AC trigger-
and delivery-enabled, with maximum service period length.
Allow drivers to change these default settings since different
uAPSD client implementations may handle errors differently and
be able to recover from some errors.
Note: some APs may not function correctly if one or all ACs are
trigger- and delivery-enabled, see
http://thread.gmane.org/gmane.linux.kernel.wireless.general/93577.
We retested with this AP and later firmware doesn't have this
bug any more.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The irqsafe version ieee80211_sta_eosp_irqsafe() exists, but
drivers must not mix calls to any irqsafe/non-irqsafe function.
Both ath9k and iwlwifi, the likely first users of this interface,
use non-irqsafe RX/TX/TX status so must also use a non-irqsafe
version of this function. Since no driver uses the _irqsafe()
version, remove that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Earlier mac80211 would check whether some kind of mesh
security was enabled, when the real question was "is the
MPM in userspace"?
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since two years no mac80211 driver implement support for NAPI. Looks
this feature is unneeded, so remove it from generic mac80211 code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's various code with strange indentation,
questionable loop and locking constructs, etc.
The bigger change is moving the "sdata" argument
to the first argument of all functions, like all
other mac80211 functions that have one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding the flag to mac80211 already without testing was
clearly a mistake, one that we now pay for by having to
reserve bit 13 forever. The problem is cfg80211 doesn't
allow capability/rate changes for station entries that
were added unassociated, so the station entries cannot
be set up properly when marked associated.
Change the NL80211_FEATURE_FULL_AP_CLIENT_STATE value
to make it clear to userspace implementations that all
current kernels don't actually support it, even though
the previous bit is set, and of course also remove the
flag from mac80211 until we test and fix the issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the new extended capabilities advertising to advertise
the fact that operating mode notification is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.
The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the problem which was discussed in
"mac80211: Fix PN corruption in case of multiple
virtual interface" [1].
Amit Shakya reported a serious issue with my patch:
mac80211: serialize rx path workers" [2]:
In case, ieee80211_rx_handlers processing is going on
for skbs received on one vif and at the same time, rx
aggregation reorder timer expires on another vif then
sta_rx_agg_reorder_timer_expired is invoked and it will
push skbs into the single queue (local->rx_skb_queue).
ieee80211_rx_handlers in the while loop assumes that
the skbs are for the same sdata and sta. This assumption
doesn't hold good in this scenario and the PN gets
corrupted by PN received in other vif's skb, causing
traffic to stop due to PN mismatch."
[1] Message-Id: http://mid.gmane.org/201302041844.44436.chunkeey@googlemail.com
[2] Commit-Id: 24a8fdad35
Reported-by: Amit Shakya <amit.shakya@stericsson.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.
Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.
To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of checking every time bss_info_changed is called,
assign the pointer once depending on the interface type
and then leave it untouched until the interface type is
changed. This makes the ieee80211_bss_info_change_notify()
now a simple wrapper to call the driver only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The special case in the function isn't really needed,
instead make the suspend code a bit better and also
easier to understand and move the warning into the
driver op wrapper inline.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of calculating in ieee80211_bss_info_change_notify()
whether beaconing should be enabled or not, set it in the
correct places in the callers. This simplifies the logic in
this function at the expense of offchannel, but is also more
robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user-space (wpa_supplicant) to disable
short guard interval (SGI) for 20Mhz. The SGI-40
disable option is already handled.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change allows userspace to register for probe request
frames on an IBSS interface. Userspace then has to handle
them and send replies.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the cipher suites need to be allocated, but this
allocation fails, this leaks the internal scan request.
Fix that by going to the correct error handling label.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS is (currently) not allowed when channel
contexts are *supported*, not when they're
*not* supported. Fix the inverted test.
Reported-by: Ronald <ronald645@gmail.com>
Tested-by: Ronald <ronald645@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use NL80211_SCAN_FLAG_LOW_PRIORITY flag in mac80211's scan state
machine to prematurely terminate scan operations if outbound
traffic collides. This is useful for marking background scans so
they don't affect throughput.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[set feature flag only if software scan is used]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename struct ieee80211_vht_capabilities to ieee80211_vht_cap
and renamed its member vht_capabilities_info to vht_cap_info.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE uses two rounds of Authentication frames and both rounds require
considerable calculation to be done. This commit extends the existing
station mode authentication request to allow more control for user
space programs to build the SAE fields and to run the authentication
step ones. Only the second round with authentication transaction
sequence 2 will result in moving to authenticated state.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, channel contexts may be used or
not. If they are used, the driver must have support for
hardware scan and remain-on-channel; otherwise the driver
must not advertise support for multiple channels.
Also prohibit WDS type interfaces when channel contexts
are to be used as there's no clear definition of which
channel they use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context are the foundation for multi-channel
operation. They are are immutable and are re-created
(or re-used if other interfaces are bound to a certain
channel and a compatible channel type) on channel
switching.
This is an initial implementation and more features
will come in separate patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[some changes including RCU protection]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:
...
Country: US Environment: Indoor/Outdoor
...
Channels [157 - 157] @ 30 dBm
...
Power constraint: 13 dB
...
What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.
Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).
Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: Carl A. Cook <CACook@quantum-equities.com>
Tested-by: Carl A. Cook <CACook@quantum-equities.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior
Felix Fietkau
Karl Beldan
Alexander Bondar
Johannes Berg
Thomas Pedersen
Stanislaw Gruszka
Tejun Heo
Simon Wunderlich
Christian Lamparter
Ben Greear
John W. Linville
Antonio Quartulli
Antonio Quartulli
Sam Leffler
Mahesh Palivela
Jouni Malinen