This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.
Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch prevents libata from incorrectly modifying inquiry
VPD pages and command support data from ATAPI devices. I have tested
the patch with a SATA ATAPI tape drive on an AHCI controller.
Patch is against kernel 2.4.32 with 2.4.32-libata1.patch applied.
Anthony J. Battersby
Cybernetics
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some hardware does not support the PACKET command at all.
Other hardware supports ATAPI, but the driver does something nasty such
as calling BUG() when an ATAPI command is issued.
For these such cases, we mark them with a new flag, ATA_FLAG_NO_ATAPI.
Initial version contributed by Ben Collins.
- remove err_mask from the parameter list of the complete functions
- move err_mask to ata_queued_cmd
- initialize qc->err_mask when needed
- for each function call to ata_qc_complete(), replace the err_mask parameter with qc->err_mask.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
===============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes ata_scsi_pass_thru() properly set result code and
sense data on translation failures.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
the patch below marks several libata (and libata-driver) structures
const so that they end up in the .rodata segment and don't false-share
cachelines with things that get dirtied often.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Move ATAPI check-condition handling out of the timeout handler
- Use multi-qc-issue feature to issue REQUEST SENSE ATAPI PACKET
command upon receiving an ATAPI check-condition.
This cleans things up a lot, and eliminates a nasty recursion bug.
scsi_wait_req does not exist any more in the SCSI layer. This patch
makes it so libata can compile again.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of power packed into a little patch.
This change eliminates the sharing between our controller-wide spinlock
and the SCSI core's Scsi_Host lock. As the locking in libata was
already highly compartmentalized, always referencing our own lock, and
never scsi_host::host_lock.
As a side effect, this change eliminates a deadlock from calling
scsi_finish_command() while inside our spinlock.
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
- move default mode pages to the front of libata-scsi.c
so various functions can access them
- partial annotation of these pages, point out divergence
from sat-r06
- replace various mode page magic numbers with defines
- strengthen MODE SENSE command decoding: handle DBD
bit in cdb, yield block descriptor (per sat-r06) and
handle mode sub pages
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add lba_28_ok() and lba_48_ok() to ata.h.
- check ending block number instead of staring block number.
- use lba_28_ok() for CHS range check
- LBA28/LBA48 optimization
Suggested by Mark Lord and Alan Cox.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=====
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
move the initialization of taskfile LBA flags
"ATA_TFLAG_LBA" and "ATA_TFLAG_LBA48 flags"
to the SCSI translation functions
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- change "xlat" and "fill" actors in libata-scsi so
they are responsible for SCSI status and sense data
when they return 1. This allows GOOD status or a
specialized error to be set.
- yield an error for mode sense requests for saved
values [sat-r06]
- remove static inlines for ata_bad_scsiop() and
ata_bad_cdb() which are no longer used
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add extern ata_scsi_set_sense() to build SCSI
fixed sense data and corresponding SCSI status
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
