Patch from Lothar Wassmann
The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.
Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."
There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."
Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.
Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ppc32 kernel, when built with CONFIG_SMP and booted on a single CPU
machine, will not properly set smp_tb_synchronized, thus causing
gettimeofday() to not use the HW timebase and to be limited to jiffy
resolution. This, among others, causes unacceptable pauses when launching
X.org.
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code that sets the clock spreading feature of the Intrepid ASIC
must not be run on some machine models or those won't boot. This
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Nikola Valerjev
Single stepping an application using ptrace() fails over ARM instructions BX and BLX.
Steps to reproduce:
Compile and link the following files
main.c
-----
void foo();
int main() {
foo();
return 0;
}
foo.s
-----
.text
.globl foo
foo:
BX LR
Using ptrace() functionality, run to main(), and start singlestepping.
Singlestep over \"BX LR\" instruction won\'t transfer the control back
to main, but run the code to completion.
This problems seems to be in the function get_branch_address() in
arch/arm/kernel/ptrace.c. The function doesn\'t seem to recognize BX
and BLX instructions as branches. BX and BLX instructions can be used
to convert from ARM to Thumb mode if the target address has the low
bit set. However, they are also perfectly legal in the ARM only mode.
Although other things in the kernel seem to indicate that only ARM
mode is accepted (and not Thumb), many compilers will generate BX
and BLX instructions even when generating ARM only code.
Signed-off-by: Nikola Valerjev <nikola@ghs.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ppc64, when opening a new hugepage region, we need to make sure any
old normal-page SLBs for the area are flushed on all CPUs. There was
a bug in this logic - after putting the new hugepage area masks into
the thread structure, we copied it into the paca (read by the SLB miss
handler) only on one CPU, not on all. This could cause incorrect SLB
entries to be loaded when a multithreaded program was running
simultaneously on several CPUs. This patch corrects the error,
copying the context information into the PACA on all CPUs using the mm
in question before flushing any existing SLB entries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On most powerpc CPUs, the dcache and icache are not coherent so
between writing and executing a page, the caches must be flushed.
Userspace programs assume pages given to them by the kernel are icache
clean, so we must do this flush between the kernel clearing a page and
it being mapped into userspace for execute. We were not doing this
for hugepages, this patch corrects the situation.
We use the same lazy mechanism as we use for normal pages, delaying
the flush until userspace actually attempts to execute from the page
in question.
Tested on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cache info is setup by walking the device tree in initialize_cache_info().
However, icache_flush_range might be called before that, in
slb_initialize()->patch_slb_encoding, which modifies the load immediate
instructions used with SLB fault code.
Not only that, but depending on memory layout, we might take SLB faults
during unflatten_device_tree. So that fault will load an SLB entry that
might not contain the right LLP flags for the segment.
Either we can walk the flattened device tree to setup cache info, or
we can pick the known defaults that are known to work. Doing it in the
flattened device tree is hairier since we need to know the machine type
to know what property to look for, etc, etc.
For now, it's just easier to go with the defaults. Worst thing that
happens from it is that we might waste a few cycles doing too small
dcbst/icbi increments.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 64k pages patch changed the meaning of one argument passed to the
low level hash functions (from "large" it became "psize" or page size
index), but one of the call sites wasn't properly updated, causing
potential random weird problems with huge pages. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This bug exists in the current code and prevents machines from booting
with numa enabled if there is a node that does not contain memory.
Workaround is to boot with 'numa=off'. Looks like a simple typo.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
What is the value shown in "cpu MHz" of /proc/cpuinfo when CPUs are capable of
changing frequency?
Today the answer is: It depends.
On i386:
SMP kernel - It is always the boot frequency
UP kernel - Scales with the frequency change and shows that was last set.
On x86_64:
There is one single variable cpu_khz that gets written by all the CPUs. So,
the frequency set by last CPU will be seen on /proc/cpuinfo of all the
CPUs in the system. What you see also depends on whether you have constant_tsc
capable CPU or not.
On ia64:
It is always boot time frequency of a particular CPU that gets displayed.
The patch below changes this to:
Show the last known frequency of the particular CPU, when cpufreq is present. If
cpu doesnot support changing of frequency through cpufreq, then boot frequency
will be shown. The patch affects i386, x86_64 and ia64 architectures.
Signed-off-by: Venkatesh Pallipadi<venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch moves away PMBASE reading and only performs it at
cpufreq_register_driver time by exiting with -ENODEV if unable to read
the value.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The attached patch introduces runtime latency measurement for ICH[234]
based chipsets instead of using CPUFREQ_ETERNAL. It includes
some sanity checks in case the measured value is out of range and
assigns a safe value of 500uSec that should still be enough on
problematics chipsets (current testing report values ~200uSec). The
measurement is currently done in speedstep_get_freqs in order to avoid
further unnecessary transitions and in the hope it'll come handy for SMI
also.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
speedstep-ich.c | 4 ++--
speedstep-lib.c | 32 +++++++++++++++++++++++++++++++-
speedstep-lib.h | 1 +
speedstep-smi.c | 1 +
4 files changed, 35 insertions(+), 3 deletions(-)
If a user has booted with 'quiet', some important messages don't
get displayed which really should. We've seen at least one case
where powernow-k8 stopped working, and the user needed a BIOS update
that they didn't know about.
Signed-off-by: Dave Jones <davej@redhat.com>
The patch that added support for a new platform chipset (shub2) broke
PTC deadlock recovery on older versions of the chipset. (PTCs are the
SN platform-specific method for doing a global TLB purge). This
patch fixes deadlock recovery so that it works on both the old & new
chipsets.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We have a customer application which trips a bug. The problem arises
when a driver attempts to call do_munmap on an area which is mapped, but
because current->thread.task_size has been set to 0xC0000000, the call
to do_munmap fails thinking it is an unmap beyond the user's address
space.
The comment in fs/binfmt_elf.c in load_elf_library() before the call
to SET_PERSONALITY() indicates that task_size must not be changed for
the running application until flush_thread, but is for ia64 executing
ia32 binaries.
This patch moves the setting of task_size from SET_PERSONALITY() to
flush_thread() as indicated. The customer application no longer is able
to trip the bug.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The per-node data structures are allocated with strided offsets that are a
function of the node number. This prevents excessive cache-aliasing from
occurring.
On systems with a large number of nodes, the strided offset becomes
too large. This patch restricts the maximum offset to 32MB. This is far larger
than the size of any current L3 cache.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix only patch to add fixup code that sets up
pci_controller->window. This code is a temporary
fix until ACPI support on Altix is added.
Also, corrects the usage of pci_dev->sysdata,
which had previously been used to reference
platform specific device info, to now point to
a pci_controller struct.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Return -EINTR instead of -ERESTARTSYS when signals are delivered during
a blocked read of /proc/sal/*/event. This allows salinfo_decode to
detect signals when it is blocked on a read of those files.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There's never been a hardware platform that has both pSeries/RPA LPAR
hypervisor and stab (pre-POWER4 segment management). This removes
the redundant code in stab_initalize().
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit da0825fd20, making
it so that if you select CONFIG_PPC_MULTIPLATFORM you get support
for PMAC, PREP and CHRP built in.
The reason for not allowing PMAC, PREP and CHRP to be selected
individually for ARCH=ppc is that there is too much interdependency
between them in the platform support code. For example, CHRP uses
the PMAC nvram code.
Configuring with ARCH=powerpc does allow you to select support for
PMAC and CHRP separately. Support for PREP is not there yet but
should be there soon.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous commit will use the page-at-a-time hypervisor call for
setting up IOMMU entries when we are using 64k pages and setting up
one 64k page, even though that means 16 calls to the hypervisor, since
the hypervisor still works on 4k pages. This optimizes this case by
using the multi-page IOMMU setup hypervisor call instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the sn2_defconfig file for the Altix 330 hardware, enables
the AGP graphics for the SGI Prism, and removes prompts for the remainder
of the new features. Greg Edwards reviewed the changes.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Must adjust tcenum and npages by TCE_PAGE_FACTOR to convert between
64KB pages and TCE (4K) pages. (This is done in other places, except
for this one location.)
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Correctly specify treeboot based image entrypoint. Currently makefile uses
$(ENTRYPOINT) which isn't defined anywhere. Each board port sets
entrypoint-$(CONFIG_BOARD_NAME) instead.
Without this patch I cannot boot Ocotea (PPC440GX eval board) anymore. I
was getting random "OS panic" errors from OpenBIOS for a while, but with
current kernel I get them all the time (probably because image became
bigger).
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The time to wait after deasserting PCI_RST has been counted with incorrect
value - this patch fixes the issue.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Akita requires inbuilt kernel i2c support for its GPIOs. Add this
requirement to Kconfig and update the defconfig to match.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a typo in the ARM IXDP425 setup definition that mistakenly tries
to use UART1's IRQ for UART2's traffic.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes BCSR accesses in the board setup/reset code. The registers are
actually 16-bit, and their addresses are different between DBAu1550 and
other DBAu1xx0 boards.
From Sergei Shtylylov <sshtylyov@ru.mvista.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rdhwr emulation accidentally swallowed the SIGILL from most other
illegal instructions. Make sure to return -EFAULT by default.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Check if IRQ is disabled or in progress before reenabling interrupts
in jmr3927_irq_end..
o s/spinlock_irqsave/spin_lock_irqsave/
o s/spinlock_irqrestore/spin_unlock_irqrestore/
o Flush write buffer after setting IRQ mask
o In 2.6 jmr3927_ioc_interrupt interrupt handlers return irqreturn_t
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thanks to LinuxICC (http://linuxicc.sf.net), a comparison of a u32 less
than 0 was found, this patch changes the variable to a signed int so that
comparison is meaningful.
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Lazy flush_dcache_page() causes userspace instability on SMP
platforms, so disable it for now.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Setting irq affinity stops working when MSI is enabled. With MSI, move_irq
is empty, so we can't change irq affinity. It appears a typo in Ashok's
original commit for this issue. X86_64 actually is using move_native_irq.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently discovered a bug on PPC which causes the floating point
registers to get corrupted when CONFIG_PREEMPT=y.
The problem occurred while running a multi threaded Java application that
does floating point. The problem could be reproduced in anywhere from 2 to
6 hours. With the patch I have included below it ran for over a week
without failure.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Tom Rini <trini@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Anne NICOLAS <anne.nicolas@mandriva.com> and Andres Kaaber
<andres.kaaber@rescue.ee> reported their HP laptop didn't reboot smoothly.
Signed-off-by: Thierry Vignaud <tvignaud@mandriva.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the correct pointer to clear the memory of the return values,
to prevent stack corruption in the callers stackframe.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug noticed by Paolo Galtieri and fixed for ARCH=ppc in
the previous commit (ppc: fix floating point register corruption).
This fixes the arch/powerpc code by adding preempt_disable/enable,
and also cleans it up a bit by pulling out the code that discards
any lazily-switched CPU register state into a new function, rather
than having that code repeated in three places.
Signed-off-by: Paul Mackerras <paulus@samba.org>
I recently discovered a bug on PPC which causes the floating point
registers to get corrupted when CONFIG_PREEMPT=y.
The problem occurred while running a multi threaded Java application that
does floating point. The problem could be reproduced in anywhere from 2 to
6 hours. With the patch I have included below it ran for over a week
without failure.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Tom Rini <trini@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Increment the PFN field of the PTE so that the tests
on vm_pfn in mm/memory.c match up. The TLB ignores these
lower bits for larger page sizes, so it's OK to set things
like this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Future versions of the Opteron processor may support
frequency transitions of 100 MHz, instead of the=20
current 200 MHz. This patch enables the powernow-k8
driver to transition to an odd FID code, indicating
a multiple of 100 MHz frequency.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
break.b always sets cr.iim to 0 and the current code tries to
get the break_num by decoding instruction. However, their
seems to be a race condition while reading the regs->cr_iip,
as on other cpu the break.b at regs->cr_iip might have been
replaced with the original instruction as a result of
unregister_kprobe() and hence decoding instruction to
obtain break_num will result in wrong value in this case.
Also includes changes to kprobes.c which now has to handle
break number zero.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
A single SGI Altix system can be divided into multiple partitions,
each running their own instance of the Linux kernel. pfn_valid()
is currently not optimal for any but the first partition, since it
does not compare the pfn with min_low_pfn before calling the more
costly ia64_pfn_valid().
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Both 32-bit and 64-bit use the same inline flush_icache_range definition
now, so both need to export __flush_icache_range, not just 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export symbol needed to allow MOL to run. This was changed to be inline
in past and forgot to be change here.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch is for supporting IDE interface for M3A-2170(Mappi-III) board.
Signed-off-by: Mamoru Sakugawa <sakugawa@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a deadlock problem of the m32r SMP kernel.
In the m32r kernel, sys_tas() system call is provided as a test-and-set
function for userspace, for backward compatibility.
In some multi-threading application program, deadlocks were rarely caused
at sys_tas() funcion. Such a deadlock was caused due to a collision of
__pthread_lock() and __pthread_unlock() operations.
The "tas" syscall is repeatedly called by pthread_mutex_lock() to get a
lock, while a lock variable's value is not 0. On the other hand,
pthead_mutex_unlock() sets the lock variable to 0 for unlocking.
In the previous implementation of sys_tas() routine, there was a
possibility that a unlock operation was ignored in the following case:
- Assume a lock variable (*addr) was equal to 1 before sys_tas() execution.
- __pthread_unlock() operation is executed by the other processor
and the lock variable (*addr) is set to 0, between a read operation
("oldval = *addr;") and the following write operation ("*addr = 1;")
during a execution of sys_tas().
In this case, the following write operation ("*addr = 1;") overwrites the
__pthread_unlock() result, and sys_tas() fails to get a lock in the next
turn and after that.
According to the attatched patch, sys_tas() returns 0 value in the next
turn and deadlocks never happen.
Signed-off-by: Hitoshi Yamamoto <Yamamoto.Hitoshi@ap.MitsubishiElectric.co.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch implements a bunch of small changes to the FRV arch to
make it work again.
It deals with the following problems:
(1) SEM_DEBUG should be SEMAPHORE_DEBUG.
(2) The argument list to pcibios_penalize_isa_irq() has changed.
(3) CONFIG_HIGHMEM can't be used directly in #if as it may not be defined.
(4) page->private is no longer directly accessible.
(5) linux/hardirq.h assumes asm/hardirq.h will include linux/irq.h
(6) The IDE MMIO access functions are given pointers, not integers, and so
get type casting errors.
(7) __pa() is passed an explicit u64 type in drivers/char/mem.c, but that
can't be cast directly to a pointer on a 32-bit platform.
(8) SEMAPHORE_DEBUG should not be contingent on WAITQUEUE_DEBUG as that no
longer exists.
(9) PREEMPT_ACTIVE is too low a value.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This replaces the (in my opinion horrible) VM_UNMAPPED logic with very
explicit support for a "remapped page range" aka VM_PFNMAP. It allows a
VM area to contain an arbitrary range of page table entries that the VM
never touches, and never considers to be normal pages.
Any user of "remap_pfn_range()" automatically gets this new
functionality, and doesn't even have to mark the pages reserved or
indeed mark them any other way. It just works. As a side effect, doing
mmap() on /dev/mem works for arbitrary ranges.
Sparc update from David in the next commit.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
This updates the Zaurus defconfigs. Poodle gets merged into
corgi_defconfig and support for tosa and akita is enabled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add iWMMX Extentions for the pxa27x based Zaurus models and
fix a couple of minor mistakes in the PXA Kconfig file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We must not call TLB maintainence operations with interrupts disabled,
otherwise we risk a lockup in the SMP IPI code.
This means that consistent_free() can not be called from a context with
IRQs disabled. In addition, we must not hold the lock in consistent_free
when we call flush_tlb_kernel_range(). However, we must continue to
prevent consistent_alloc() from re-using the memory region until we've
finished tearing down the mapping and dealing with the TLB.
Therefore, leave the vm_region entry in the list, but mark it inactive
before dropping the lock and starting the tear-down process. After the
mapping has been torn down, re-acquire the lock and remove the entry
from the list.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't really need to check whether the machine type is Netwinder
or CATS before setting up the PCI IO mapping for debugging. This
allows us to eliminate asm/mach-types.h from head.S
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Blah. The patch [0] I recently sent fixing errors with
in_hugepage_area() and prepare_hugepage_range() for powerpc itself has
an off-by-one bug. Furthermore, the related functions
touches_hugepage_*_range() and within_hugepage_*_range() are also
buggy. Some of the bugs, like those addressed in [0] originated with
commit 7d24f0b8a5 where we tweaked the
semantics of where hugepages are allowed. Other bugs have been there
essentially forever, and are due to the undefined behaviour of '<<'
with shift counts greater than the type width (LOW_ESID_MASK could
return non-zero for high ranges with the right congruences).
The good news is that I now have a testsuite which should pick up
things like this if they creep in again.
[0] "powerpc-fix-for-hugepage-areas-straddling-4gb-boundary"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the removal of include/asm-powerpc, we no longer need
arch/powerpc/include/asm for the 64 bit build. We also do not need
-Iarch/powerpc for the 64 bit build either.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The DBG() call where updated with the appropriate KERN_* symbol.
Signed-off-by: Daniel Marjamki <daniel.marjamaki@comhem.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When attempting to hotadd a PCI card with a bridge on it, I saw
the kernel reporting resource collision errors even when there were
really no collisions. The problem is that the code doesn't skip
over "invalid" resources with their resource type flag not set.
Others have reported similar problems at boot time and for
non-bridge PCI card hotplug too, where the code flags a
resource collision for disabled ROMs. This patch fixes both
problems.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modified common.c so it's using the appropriate KERN_* in printk() calls.
Signed-off-by: Daniel Marjamkia <daniel.marjamaki@comhem.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 7d24f0b8a5 fixed bugs in the ppc64 SLB
miss handler with respect to hugepage handling, and in the process tweaked
the semantics of the hugepage address masks in mm_context_t.
Unfortunately, it left out a couple of necessary changes to go with that
change. First, the in_hugepage_area() macro was not updated to match,
second prepare_hugepage_range() was not updated to correctly handle
hugepages regions which straddled the 4GB point.
The latter appears only to cause process-hangs when attempting to map such
a region, but the former can cause oopses if a get_user_pages() is
triggered at the wrong point. This patch addresses both bugs.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug in kprobes that can cause an Oops or even a crash when a return
probe is installed on one of the following functions: sys_execve,
do_execve, load_*_binary, flush_old_exec, or flush_thread. The fix is to
remove the call to kprobe_flush_task() in flush_thread(). This fix has
been tested on all architectures for which the return-probes feature has
been implemented (i386, x86_64, ppc64, ia64). Please apply.
BACKGROUND
Up to now, we have called kprobe_flush_task() under two situations: when a
task exits, and when it execs. Flushing kretprobe_instances on exit is
correct because (a) do_exit() doesn't return, and (b) one or more
return-probed functions may be active when a task calls do_exit(). Neither
is the case for sys_execve() and its callees.
Initially, the mistaken call to kprobe_flush_task() on exec was harmless
because we put the "real" return address of each active probed function
back in the stack, just to be safe, when we recycled its
kretprobe_instance. When support for ppc64 and ia64 was added, this safety
measure couldn't be employed, and was eventually dropped even for i386 and
x86_64. sys_execve() and its callees were informally blacklisted for
return probes until this fix was developed.
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restore an earlier mod which went missing in the powerpc reshuffle: the 4xx
mmu_mapin_ram does not need to take init_mm.page_table_lock.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update comments (only) on page_table_lock and mmap_sem in arch/powerpc.
Removed the comment on page_table_lock from hash_huge_page: since it's no
longer taking page_table_lock itself, it's irrelevant whether others are; but
how it is safe (even against huge file truncation?) I can't say.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Email address update, changing old work address to personal (permanent)
one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Earlier I unifdefed PageCompound, so that snd_pcm_mmap_control_nopage and
others can give out a 0-order component of a higher-order page, which won't
be mistakenly freed when zap_pte_range unmaps it. But many Bad page states
reported a PG_reserved was freed after all: I had missed that we need to
say __GFP_COMP to get compound page behaviour.
Some of these higher-order pages are allocated by snd_malloc_pages, some by
snd_malloc_dev_pages; or if SBUS, by sbus_alloc_consistent - but that has
no gfp arg, so add __GFP_COMP into its sparc32/64 implementations.
I'm still rather puzzled that DRM seems not to need a similar change.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Although we tend to associate VM_RESERVED with remap_pfn_range, quite a few
drivers set VM_RESERVED on areas which are then populated by nopage. The
PageReserved removal in 2.6.15-rc1 changed VM_RESERVED not to free pages in
zap_pte_range, without changing those drivers not to set it: so their pages
just leak away.
Let's not change miscellaneous drivers now: introduce VM_UNPAGED at the core,
to flag the special areas where the ptes may have no struct page, or if they
have then it's not to be touched. Replace most instances of VM_RESERVED in
core mm by VM_UNPAGED. Force it on in remap_pfn_range, and the sparc and
sparc64 io_remap_pfn_range.
Revert addition of VM_RESERVED to powerpc vdso, it's not needed there. Is it
needed anywhere? It still governs the mm->reserved_vm statistic, and special
vmas not to be merged, and areas not to be core dumped; but could probably be
eliminated later (the drivers are probably specifying it because in 2.4 it
kept swapout off the vma, but in 2.6 we work from the LRU, which these pages
don't get on).
Use the VM_SHM slot for VM_UNPAGED, and define VM_SHM to 0: it serves no
purpose whatsoever, and should be removed from drivers when we clean up.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On some systems, libc PAGE_SIZE calls getpagesize, which can't happen from a
stub. So, I use UM_KERN_PAGE_SIZE, which is less variable in its definition,
instead.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes stub_segv use the stub_syscall macros. This was needed
anyway, but the bug that prompted this was the discovery that gcc was storing
stuff in RCX, which is trashed across a system call. This is exactly the sort
of problem that the new macros fix.
There is a stub_syscall0 for getpid. stub_segv was changed to be a libc file,
and that caused some include changes.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This gives a name to the anonymous union introduced in skas-hold-own-ldt,
allowing to build on a wider range of gccs.
It also removes ldt.h, which somehow became real, and replaces it with a
symlink, and creates ldt-x86_64.h as a copy of ldt-i386.h for now.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We have a bug in the i386 stub_syscall6 which pushes ebp before the system
call and pops it afterwards. Because we use syscall6 to remap the stack, the
old contents of the stack (and the former value of ebp) are no longer
available. Some versions of gcc make from a real local, accessed through ebp,
despite my efforts to make it obvious that references to from are really
constants. This patch attempts to make it even more obvious by eliminating
from and using a macro to access the stub's data explicitly with constants.
My original thinking on this was to replace syscall6 with a remap_stack
interface which saved ebp someplace and restored it afterwards. The problem
is that there are no registers to put it in, except for esp. That could work,
since we can store a constant in esp after the mmap because we just replaced
the stack. However, this approach seems a tad cleaner.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The nasid_index was not being incremented if the
pointer was null, causing an infinite loop.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
The kernel's use of the for_each_*cpu(i) macros has allowed for sparse CPU
numbering. When I hacked the kernel to test sparse cpu_present_map[] and
cpu_possible_map[] cpumasks, I discovered one remaining spot, in
sn_hwperf_ioctl() during sn initialization, that needs to be fixed.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch to prevent sn2_ptc_init code from attempting to load on non-sn2 systems
when sn2_smp.c is built-in to generic kernel.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch cleans up some error messages in the
powernow-k8 driver and makes them more understandable.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Patch from Dirk Opfer
Fix an error in tosa.c after the platform device conversion.
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Needed to make the earlier use disabled CPUs for CPU hotplug patch
actually work.
Need to register disabled processors as well, so we can count them
towards cpu_possible_map as hot pluggable cpus.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bigsmp is reported to work on large Opteron systems on 32bit too.
Enable it by default there.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were using udelay in the loop on the primary cpu waiting for the
secondary cpu to take the timebase value. Unfortunately now that
udelay uses the timebase, and the timebase is stopped at this point,
the udelay never terminated. This fixes it by not using udelay, and
increases the number of loops before we time out to compensate.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Daniel Jacobowitz
After delivering a signal (creating its stack frame) we must check for
additional pending unblocked signals before returning to userspace.
Otherwise signals may be delayed past the next syscall or reschedule.
Once that was fixed it became obvious that the ARM signal mask manipulation
was broken. It was a little bit broken before the recent SA_NODEFER
changes, and then very broken after them. We must block the requested
signals before starting the handler or the same signal can be delivered
again before the handler even gets a chance to run.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This involves some minor changes: a few unused functions that the
ppc32 pci.c provides are no longer declared here or exported;
pcibios_assign_all_busses now just refers to the pci_assign_all_buses
variable on both 32-bit and 64-bit; pcibios_scan_all_fns is now
just 0 instead of a function that always returns 0 on 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-ppc64/imalloc.h is only included from files in arch/powerpc/mm.
We already have a header for mm local definitions,
arch/powerpc/mm/mmu_decl.h. Thus, this patch moves the contents of
imalloc.h into mmu_decl.h. The only exception are the definitions of
PHBS_IO_BASE, IMALLOC_BASE and IMALLOC_END. Those are moved into
pgtable.h, next to similar definitions of VMALLOC_START and
VMALLOC_SIZE.
Built for multiplatform 32bit and 64bit (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Trying to set the priority would just disable the interrupt due to an
incorrect mask used. We rarely use that call, in fact, I think only in
the powermac code for the cmd-power key combo that triggers xmon. So it
got unnoticed for a while.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Unfortunately, later gcc versions error out when our get_user is passed
a const pointer, since we write to a temporary variable declared as
typeof(*(p)) which propagates the const-ness.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
make defconfig will now use arch/powerpc/configs/ppc64_defconfig
if running on a ppc64 system. I need to add an
arch/powerpc/configs/ppc_defconfig sometime.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes 32-bit CHRP systems use the RTAS time-of-day routines if
available. It fixes a bug in the RTAS time-of-day routines where they
were storing a 64-bit timebase value in an unsigned long by making
those variables u64. Also, the direct-access time-of-day routines
had the wrong convention for the month and year in the struct rtc_time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_dedicated_idle() was using __get_tb which used to be defined
in asm/delay.h. Change it to use get_tb from asm/time.h, which is
in fact exactly the same thing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also deletes the now-unused Makefiles under arch/ppc64.
Both of the files moved over could use some merging, but for now I
have moved them as-is and arranged for them to be used only in 64-bit
kernels. For 32-bit kernels we still use arch/ppc/kernel/idle.c and
drivers/char/generic_nvram.c as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The config option SPAN_OTHER_NODES was created so that we could
make pSeries numa layouts work within the DISCONTIG memory model.
Now that DISCONTIG has been replaced by SPARSEMEM, we can eliminate
this option.
I'll be sending a separate patch to Andrew to remove the arch
independent code as pSeries was the only arch that needed this.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges align.c, the result isn't quite what was in ppc64 nor
what was in ppc32 :) It should implement all the functionalities of both
though. Kumar, since you played with that in the past, I suppose you
have some test cases for verifying that it works properly before I dig
out the 601 machine ? :)
Since it's likely that I won't be able to test all scenario, code
inspection is much welcome.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My earlier merge of delay.h introduced a timebase-based udelay for
32-bit machines but also broke the 601, which doesn't have the
timebase register. This fixes it by using the 601's RTC register on
the 601, and also moves __delay() and udelay() to be out-of-line in
arch/powerpc/kernel/time.c. These functions aren't really performance
critical, after all.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we moved things around in irq.h seq_file became an issue. Fix
warnings related to its usage.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SVRs for MPC8343/E were incorrect and really the SVRs
for MPC8347/E.
Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reserve the Maple RTC I/O resource. Needed now we use genrtc.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replacing the string labels with numbers saves 117 bytes in the final zImage.
These local labels are not discared.
Signed-off-by: Olaf Hering <olh@suse.de>
arch/powerpc/boot/crt0.S | 23 +++++++++++------------
1 files changed, 11 insertions(+), 12 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we moved things around in irq.h seq_file became an issue. Fix
warnings related to its usage.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Document that the VMALLOC_END address must be aligned to 2MB since
it must align with a PGD boundary.
Allocate the vectors page early so that the flush_cache_all() later
will cause any dirty cache lines in the direct mapping will be safely
written back.
Move the flush_cache_all() to the second local_flush_cache_tlb() and
remove the now redundant first local_flush_cache_tlb().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove drm compat_ioctl handlers. The drm drivers have proper
compat_ioctl methods these days.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Move PA perf driver over to ->compat_ioctl.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix some compile problems:
- ret wasn't being initialised in all code paths
- I'm pretty sure 'goto out' should have been 'goto out_tsk'
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Improve the error message when we get a clashing mod path, and
actually display the IODC data and path for the conflicting device.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Return PDC_OK when device registration fails so that we enumerate all
subsequent devices, even when we get two devices with the same hardware
path (which should never happen, but does with at least one revision of
rp8400 firmware).
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Document clobbers and args in entry.S and syscall.S.
entry.S: Add comment to indicate that cr27 may recycle and EDEADLOCK
detection is not 100% correct. Since this is only enabled when using
ENABLE_LWS_DEBUG, the user is warned by the comment.
Signed-off-by: Carlos O'Donell <carlos@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make the "redirecting irq" message to not display on the console by
setting the severity to KERN_DEBUG. The console was basically unusable.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
irq_affinityp[] only available for SMP builds, make code that uses
it conditional on CONFIG_SMP.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This really only adds them for the machines I can check SMP on, which
is CPU interrupts and IOSAPIC (so not any of the GSC based machines).
With this patch, irqbalanced can be used to maintain irq balancing.
Unfortunately, irqbalanced is a bit x86 centric, so it doesn't do an
incredibly good job, but it does work.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Since irq.c uses smp_send_all_nop, we must define it for UP builds
as well. Make it a static inline so it gets optimized away. This forces
irq.c to include <asm/smp.h> though.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix our interrupts not to use smp_call_function
On K and D class smp, the generic code calls this under an irq
spinlock, which causes the WARN_ON() message in smp_call_function()
(and is also illegal because it could deadlock).
The fix is to use a new scheme based on the IPI_NOP.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Disable nesting of interrupts - still has holes
The offending sequence starts out like this:
1) take external interrupt
2) set_eiem() to only allow TIMER_IRQ; local interrupts still disabled
3) read the EIRR to get a "list" of pending interrupts
4) clear EIRR of pending interrupts we intend to handle
5) call __do_IRQ() to handle IRQ.
6) handle_IRQ_event() enables local interrupts (I-Bit)
7) take a timer interrupt
8) read EIRR to get a new list of pending interrupts
9) clear EIRR of pending interrupts we just read
10) handle pending interrupts found in (8)
11) set_eiem(cpu_eiem) and return
[ TROUBLE! all enabled CPU IRQs are unmasked. }
12) handle remaining interrupts pending from (3)
e.g. call __do_IRQ() -> handle_IRQ_event()..etc
[ TROUBLE! call to handle_IRQ_event() can now enable *any* IRQ. }
13) set_eiem(cpu_eiem) and return
The problem is we now get into ugly race conditions with Timer and IPI
interrupts at this point. I'm not exactly sure what happens when
things go wrong (perhaps nest calls to IPI or timer interrupt?).
But I'm certain it's not good.
This sequence will break sooner if (10) would accidentally leave
interrupts enabled.
I'm pretty sure the right answer is now to make cpu_eiem
a per CPU variable since all external interrupts on parisc
are per CPU. This means we will NOT need to send an IPI to
every CPU in the system when enabling or disabling an IRQ
since only one CPU needs to change it's EIEM.
Thanks to James Bottomley for (once again) pointing out the problem.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix a longstanding smp bug
The problem is that both the timer and ipi interrupts are being called
with interrupts enabled, which isn't what anyone is expecting.
The IPI issue has just started to show up by causing a BUG_ON in the
slab debugging code. The timer issue never shows up because there's an
eiem work around in our irq.c
The fix is to label both these as SA_INTERRUPT which causes the generic
irq code not to enable interrupts.
I also suspect the smp_call_function timeouts we're seeing might be
connected with the fact that we disable IPIs when handling any other
type of interrupt. I've put a WARN_ON in the code for executing
smp_call_function() with IPIs disabled.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Polish the comments specifically in vhpt_miss and nested_dtlb_miss
handlers. I think it's better to explicitly name each page table
level with its name instead of numerically name them. i.e., use
pgd, pud, pmd, and pte instead of referring as L1, L2, L3 etc.
Along the line, remove some magic number in the comments like:
"PTA + (((IFA(61,63) << 7) | IFA(33,39))*8)". No code change at
all, pure comment update. Feel free to shoot anything you have,
darts or tomahawk cruise missile. I will duck behind a bunker ;-)
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
From source code inspection, I think there is a bug with 4 level
page table with vhpt_miss handler. In the code path of rechecking
page table entry against previously read value after tlb insertion,
*pte value in register r18 was overwritten with value newly read
from pud pointer, render the check of new *pte against previous
*pte completely wrong. Though the bug is none fatal and the penalty
is to purge the entry and retry. For functional correctness, it
should be fixed. The fix is to use a different register so new
*pud don't trash *pte. (btw, the comments in the cmp statement is
wrong as well, which I will address in the next patch).
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The "align" argument in ARMs __ioremap is unused and provides a
misleading expectation that it might do something. It doesn't.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
