This patch adds the definitions used by pfkeyv2 interface for Camellia
cipher algorithm.
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that all cipher/compression users have switched over to the new
allocation scheme, we can get rid of the compatility defines and use
proper structs for them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds support for multiple frontend types for each backend
algorithm by passing the type and mask through to the backend type
init function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The problem was introduced in 2.6.18.3 with the casting of some
36bit-defines (PCI memory) in au1000.h to resource_size_t which may be
u32 or u64 depending on the experimental CONFIG_RESOURCES_64BIT.
With unset CONFIG_RESOURCES_64BIT, the pci-memory cannot be accessed
because the ioremap in arch/mips/au1000/common/pci.c already used the
truncated addresses.
With set CONFIG_RESOURCES_64BIT, things get even worse, because PCI-scan
aborts, due to resource conflict: request_resource() in arch/mips/pci/pci.c
fails because the maximum iomem-address is 0xffffffff (32bit) but the
pci-memory-start-address is 0x440000000 (36bit).
To get pci working again, I propose the following patch:
1. remove the resource_size_t-casting from au1000.h again
2. make the casting in arch/mips/au1000/common/pci.c (it's allowed and
necessary here. The 36bit-handling will be done in __fixup_bigphys_addr).
With this patch pci works again like in 2.6.18.2, the gcc-compile warnings
in pci.c are gone and it doesn't depend on CONFIG_EXPERIMENTAL.
Signed-off-by: Alexander Bigga <ab@mycable.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/au1000/common/pci.o
arch/mips/au1000/common/pci.c:42: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:43: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:49: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:50: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c: In function ‘au1x_pci_setup’:
arch/mips/au1000/common/pci.c:82: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The old code was assuming that min_low_pfn was always 0. This
means that platforms having a big hole at their memory start
paid the price of wasting some memory for the allocation of
unused entries in mem_map[].
This patch prevents this waste.
It introduces PHYS_OFFSET define which is the start of the
physical memory and uses it wherever needed. Specially when
converting physical/virtual addresses into virtual/physical
ones.
Currently all platforms defines PHYS_OFFSET to 0.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes a better usage of these two globals.
'min_low_pfn' is now correctly setup for all configs, which
allow us to rely on it in boot memory code init.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current prom_free_prom_memory() implementations are almost same as
free_init_pages(), or no-op. Make free_init_pages() extern (again)
and make prom_free_prom_memory() use it.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move I8259A_IRQ_BASE from asm/i8259.h to asm/mach-generic/irq.h and
make it really customizable. And remove I8259_IRQ_BASE declared on
some platforms. Currently only NEC_CMBVR4133 is using custom
I8259A_IRQ_BASE value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq_base for {mips,rm7k,rm9k}_cpu_irq_init() are constant on all
platforms and are same value on most platforms (0 or 16, depends on
CONFIG_I8259). Define them in asm-mips/mach-generic/irq.h and make
them customizable. This will save a few cycle on each CPU interrupt.
A good side effect is removing some dependencies to MALTA in generic
SMTC code.
Although MIPS_CPU_IRQ_BASE is customizable, this patch changes irq
mappings on DDB5477, EMMA2RH and MIPS_SIM, since really customizing
them might cause some header dependency problem and there seems no
good reason to customize it. So currently only VR41XX is using custom
MIPS_CPU_IRQ_BASE value, which is 0 regardless of CONFIG_I8259.
Testing this patch on those platforms is greatly appreciated. Thank
you.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add abstraction so that the file can be used by environments other than IA64
and EM64T, namely for Xen.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes
- marking I-cache clean of pages DMAed to now only done for IA64
- broken multiple inclusion in include/asm-x86_64/swiotlb.h
- missing call to mark_clean in swiotlb_sync_sg()
- a (perhaps only theoretical) issue in swiotlb_dma_supported() when
io_tlb_end is exactly at the end of memory
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
getcpu system call returns cpu# and node# on which this system call and
its caller are running. This patch hooks up its implementation on IA64.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It does not return NULL when arg is NULL.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While pursuing and unrelated issue with 64Mb granules I noticed a problem
related to inconsistent use of add_active_range. There doesn't appear any
reason to me why FLATMEM versus DISCONTIG_MEM should register memory to
add_active_range with different code. So I've changed the code into a
common implementation.
The other subtle issue fixed by this patch was calling add_active_range in
count_node_pages before granule aligning is performed. We were lucky with
16MB granules but not so with 64MB granules. count_node_pages has reserved
regions filtered out and as a consequence linked kernel text and data
aren't covered by calls to count_node_pages. So linked kernel regions
wasn't reported to add_active_regions. This resulted in free_initmem
causing numerous bad_page reports. This won't occur with this patch
because now all known memory regions are reported by
register_active_ranges.
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)
Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As is pointed out in
http://www.gelato.org/community/view_linear.php?id=1_1036&from=authors&value=Ian%20Wienand#1_1039,
if single step on break instruction, the break fault has higher
priority than the single-step trap. When the break fault handler
is entered, it advances the IP by 1 instruction so break instruction
single-stepping is skipped, actually it is next instruction which
is single stepped.
This patch modifies this, it adds TIF_SINGLESTEP bit for thread
flags, and generate a fake sigtrap when single stepping break
instruction. Test case in attachment can verify this. Any comments
is welcome.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Set read-only flag in the page table entries for the kernel image text
section. This will catch all instruction caused corruptions withing the
text section.
Instruction replacement via kprobes still works, since it bypasses now
dynamic address translation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hopefully this will make it more maintainable and less error prone.
Code makes use of search_exception_tables(). Since it calls this
function before the kernel exeception table is sorted, there is an
early call to sort_main_extable().
This way it's easy to use the already present infrastructure of fixup
sections. Also this would allows to easily convert the rest of
head[31|64].S into C code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Preset the bogomips number to the cpu capacity value reported by
store system information in SYSIB 1.2.2. This value is constant
for a particular machine model and can be used to determine
relative performance differences between machines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
3592 tape devices are able to write data encrpyted on tape mediums.
This z/Linux device driver support includes the following functions:
* ioctl to switch on/off encryption
* ioctl to query encryption status of drive
* ioctls to set and query key encrypting keys (kekls)
* long busy interrupt handling
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support to boot from a named saved segment (NSS).
Signed-off-by: Hongjie Yang <hongjie@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Starting with the z9 the CPU Cryptographic Assist Facility comes with
an integrated Pseudo Random Number Generator. The generator creates
random numbers by an algorithm similar to the ANSI X9.17 standard.
The pseudo-random numbers can be accessed via a character device driver
node called /dev/prandom. Similar to /dev/urandom any amount of bytes
can be read from the device without blocking.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for clock synchronization to an external time
reference (ETR). The external time reference sends an oscillator
signal and a synchronization signal every 2^20 microseconds to keep
the TOD clocks of all connected servers in sync. For availability
two ETR units can be connected to a machine. If the clock deviates
for more than the sync-check tolerance all cpus get a machine check
that indicates that the clock is out of sync. For the lovely details
how to get the clock back in sync see the code below.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This provides a noexec protection on s390 hardware. Our hardware does
not have any bits left in the pte for a hw noexec bit, so this is a
different approach using shadow page tables and a special addressing
mode that allows separate address spaces for code and data.
As a special feature of our "secondary-space" addressing mode, separate
page tables can be specified for the translation of data addresses
(storage operands) and instruction addresses. The shadow page table is
used for the instruction addresses and the standard page table for the
data addresses.
The shadow page table is linked to the standard page table by a pointer
in page->lru.next of the struct page corresponding to the page that
contains the standard page table (since page->private is not really
private with the pte_lock and the page table pages are not in the LRU
list).
Depending on the software bits of a pte, it is either inserted into
both page tables or just into the standard (data) page table. Pages of
a vma that does not have the VM_EXEC bit set get mapped only in the
data address space. Any try to execute code on such a page will cause a
page translation exception. The standard reaction to this is a SIGSEGV
with two exceptions: the two system call opcodes 0x0a77 (sys_sigreturn)
and 0x0aad (sys_rt_sigreturn) are allowed. They are stored by the
kernel to the signal stack frame. Unfortunately, the signal return
mechanism cannot be modified to use an SA_RESTORER because the
exception unwinding code depends on the system call opcode stored
behind the signal stack frame.
This feature requires that user space is executed in secondary-space
mode and the kernel in home-space mode, which means that the addressing
modes need to be switched and that the noexec protection only works
for user space.
After switching the addressing modes, we cannot use the mvcp/mvcs
instructions anymore to copy between kernel and user space. A new
mvcos instruction has been added to the z9 EC/BC hardware which allows
to copy between arbitrary address spaces, but on older hardware the
page tables need to be walked manually.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently works anyway since search_binary_handler has a
set_fs(USER_DS). But start_thread() is the place where this should be
done. Following all other architectures...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cpu_relax() has barrier() semantics hence there is no need to use both
of them in conjunction in sclp_sync_wait(). Also change cpu_relax()
so it's more obvious that it has barrier semantics.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
No need to use lrag in 64 bit addressing mode since lra will do the
same.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some HID devices by Apple have both keyboard and mouse interfaces; the
keyboard interface is handled by usbhid, but the mouse (really
touchpad) interface must be handled by the separate 'appletouch'
driver. Using HID_QUIRK_IGNORE will make hiddev ignore both
interfaces, therefore a new quirk flag to ignore only the mouse
interface is required.
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidinput_{open,close}() functions do not belong to usbhid, but
to the generic HID layer. Move them, and fix hooks in struct
hid_device, so that now the callbacks are done to transport-specific
_open() functions, but not input_open() functions.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-debug.h contains a lot of code, and should not therefore
be a header.
This patch moves the code to generic hid layer as .c source, and
introduces CONFIG_HID_DEBUG to conditionally compile it, instead
of playing with #define DEBUG and including hid-debug.h.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a force feedback driver for PantherLord USB/PS2 2in1 Adapter,
0810:0001. The device identifies itself as "Twin USB Joystick".
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new quirk HID_QUIRK_SKIP_OUTPUT_REPORTS to skip output reports
when enumerating reports on a hid-input device. Add this quirk and
HID_QUIRK_MULTI_INPUT to 0810:0001.
PantherLord Twin USB Joystick, 0810:0001 has separate input reports
for 2 distinct game controllers in the same interface, so it needs
HID_QUIRK_MULTI_INPUT. However, the device also contains one output
report per controller which is used to control the force feedback
function, and we do not want those to appear as separate input
devices as well. The simplest approach seems to be to add a quirk to
skip output reports on 0810:0001, and allow the force feedback
driver to handle those.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the untyped data region in ib_user_mad have type u64 so that it
gets aligned properly. This avoids alignment faults in ib_umad when
casting the data field to an rmpp_mad and accessing the 64-bit tid
field on architectures like ia64.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_wc currently only includes the local QP number: this matches
the IB spec, but seems mostly useless. The following patch replaces
this with the pointer to qp itself, and updates all low level drivers
and all users.
This has the following advantages:
- Ability to get a per-qp context through wc->qp->qp_context
- Existing drivers already have the qp pointer ready in poll cq, so
this change actually saves a tiny bit (extra memory read) on data path
(for ehca it would actually be expensive to find the QP pointer when
polling a CQ, but ehca does not support SRQ so we can leave wc->qp as
NULL for ehca)
- Users that need the QP number can still get it through wc->qp->qp_num
Use case:
In IPoIB connected mode code, I have a common CQ shared by multiple
QPs. To track connection usage, I need a way to get at some per-QP
context upon the completion, and I would like to avoid allocating
context object per work request just to stick a QP pointer into it.
With this code, I can just use wc->qp->qp_context.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
<rdma/ib_verbs.h> uses struct kref, so it should include <linux/kref.h>
explicitly to avoid hidden include dependencies.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Many controllers have an upper limit on the number of blocks that can be
transferred in one request. Allow the host drivers to specify this and make
sure we avoid hitting this limit.
Also change the max_sectors field to avoid confusion. This makes it map
less directly to the block layer limits, but as they didn't apply directly
on MMC cards anyway, this isn't a great loss.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most controllers have an upper limit on the block size. Allow the host
drivers to specify this and make sure we avoid hitting this limit.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch also adds symbolic defines for supported pci ids.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As there's only one work item (media_switcher) to handle and it's effectively
serialized with itself, I found it more convenient to use kthread instead of
workqueue. This also allows for a working implementation of suspend/resume,
which were totally broken in the past version.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Hardware does not say whether card was inserted or removed when reporting
socket events. Moreover, during suspend, media can be removed or switched
to some other card type without notification. Therefore, for each socket
in the change set the following is performed:
1. If there's active device in the socket it's unregistered
2. Media detection is performed
3. If detection recognizes supportable media, new device is registered
This patch also alters some macros and variable names to enhance clarity.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In order to support correct suspend and resume several changes were needed:
1. Switch from work_struct to tasklet for command handling. When device
suspend is called workqueues are already frozen and can not be used.
2. Separate host initialization code from driver's probe and don't rely
on interrupts for host initialization. This, in turn, addresses two
problems:
a) Resume needs to re-initialize the host, but can not assume that
device interrupts were already re-armed.
b) Previously, probe will return successfully before really knowing
the state of the host, as host interrupts were not armed in time.
Now it uses polling to determine the real host state before returning.
3. Separate termination code from driver's remove. Termination may be caused
by resume, if media changed type or became unavailable during suspend.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Thanks to the generous donation of an SDHC card by John Gilmore, and
the surprisingly enlightened decision by the SD Card Association to
publish useful specs, I've been able to bash out support for SDHC. The
changes are not too profound:
i) Add a card flag indicating the card uses block level addressing and
check it in the block driver. As we never took advantage of byte-level
addressing, this simply involves skipping the block -> byte
translation when sending commands.
ii) The layout of the CSD is changed - a set of fields are discarded
to make space for a larger C_SIZE. We did not reference any of the
discarded fields except those related to the C_SIZE.
iii) Read and write timeouts are fixed values and not calculated from
CSD values.
iv) Before invoking SEND_APP_OP_COND, we must invoke the new
SEND_IF_COND to inform the card we support SDHC.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for these devices was broken for 2.6.18-rc1 and later by commit
146ad66eac, which added voltage level support.
This restores the previous behaviour for these devices by ensuring that when
the voltage is changed, only one write to set the voltage is performed.
It may be that both writes are needed if the voltage is being changed between
two non-zero values or that it's safe to ensure that only one write is done
if the hardware only supports one voltage; I don't know whether either is the
case nor can I test since I have only the one SD reader (1524:0550), and it
supports just the one voltage.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Change the parent of cards to be a specific host (a class
device), not the physical controller. This is particularly
useful when the hardware has multiple slots, meaning
multiple hosts.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As card_busy was only used to indicate if the host was exclusively
claimed and not really used to identify a particular card, replacing
it with just a boolean makes things a lot more easily understandable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We went and named them __NR_sys_foo instead of __NR_foo.
It may be too late to change this, but we can at least add the proper names
now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SN platform support for running with an ACPI
capable PROM that defines PCI devices in SSDT
tables. There is a SSDT table for every occupied
slot on a root bus, containing info for every
PPB and/or device on the bus. The SSDTs will be
dynamically loaded/unloaded at hotplug enable/disable.
Platform specific information that is currently
passed via a SAL call, will now be passed via the
Vendor resource in the ACPI Device object(s) defined
in each SSDT.
Signed-off-by: John Keller <jpk@sgi.com>
Cc: Greg KH <greg@kroah.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Added 2007 copyright to all module headers and signons. This affects
virtually every file in the ACPICA core subsystem, iASL compiler,
and the utilities.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Allow processor to be declered with the Device(), such as:
Device(CPU1234) {
Name(_HID, "ACPI007")
Name(_UID, 1234)
}
Signed-off-by: Len Brown <len.brown@intel.com>
Debugger: Enhanced the Statistics/Memory command to emit the
total (maximum) memory used during execution, as well as the
maximum memory consumed by each of the various object types.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented enhancements to the multithreading support within
the debugger to enable better multithreading evaluation of the subsystem.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Support for 16-bit ACPICA has been completely removed since it is
no longer necessary and it clutters the code. All 16-bit macros,
types, and conditional compiles have been removed, cleaning up
and simplifying the code across the entire subsystem.
DOS support is no longer needed since the Linux firmware kit
is now available.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
AcpiEnable will now fail if all of the required ACPI tables are not
loaded (FADT, FACS, DSDT). BZ 477
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Thus, even if the default compiler setting is non-aligned, the header is compiled
correctly.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Optimized the Load operator in the case where the source operand is an
operation region. Simply map the operation region memory, instead of
performing a bytewise read.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with a possible race condition between threads executing
AcpiWalkNamespace and the AML interpreter. This condition was removed by
modifying AcpiWalkNamespace to (by default) ignore all temporary
namespace entries created during any concurrent control method execution
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Restructured the AML ParseLoop function, breaking it into several
subfunctions in order to reduce CPU stack use and improve maintainability
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove flags parameter for acpi_{get,set}_register().
It is no longer necessary now that these functions use a
spinlock for mutual exclusion.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
to differentiate the failure modes.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Required new table init interface since iASL does not use RSDP/XSDT.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Moved all FADT-related functions to a new file, tbfadt.c.
Eliminated the acpi_hw_initialize function - the
FADT registers are now validated when the table is loaded.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhanced the implementation of the interpreters'
serialized mode (boot with "acpi_serialize" to set
acpi_glb_all_methods_serialized flag.)
When this mode is specified, instead of creating a serialization
semaphore per control method, the interpreter lock is
simply no longer released before a blocking operation
during control method execution. This effectively makes
the AML Interpreter single-threaded. The overhead of a
semaphore per-method is eliminated.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split acpi_format_exception into two parts. New
function is acpi_ut_verify_exception and will be used to
verify exception codes returned by user.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update internal GPE data structure to simplify
debug, use gpe_number instead of register bitmask.
Signed-off-by: Bob Moore <bob.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update interface to acpi_ut_repair_name() to avoid
alignment issues on IA64
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change for GPE support: when a wake GPE is
received, now all wake GPEs are immediately disabled to
prevent the waking GPE from firing again, and to prevent
other wake GPEs from interrupting the wake process.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implement support for ACPI DMAR table (DMA
Remapping Table) in header files and disassembler.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Table Manager component has been completely
redesigned and reimplemented. The new design is much
simpler, and reduces the overall code and data size of
the kernel-resident ACPICA by approximately 5%. Also,
it is now possible to obtain the ACPI tables very early
during kernel initialization, even before dynamic memory
management is initialized.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Completed a new design and implementation for
the ACPI Global Lock support. On the OS side, the global
lock is now treated as a standard AML mutex. Previously,
multiple OS threads could acquire the global lock
simultaneously, but this could cause the BIOS to be starved
by the lock in cases such as the Embedded Controller driver,
where there is a tight coupling between the OS and the BIOS.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
> Looks like you should use ata_busy_wait() here, rather than reproducing
> the same code again.
It waits in 10uS chunks while 1uS chunks were used in the workaround.
Could indeed do that once I know the fix is right. While I'm at it the
ata_busy_wait kerneldoc is borked so here's a fix
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some cases such as:
iph->check = 0;
iph->check = ip_fast_csum((unsigned char *)iph, iph->ihl);
GCC may optimize out the previous store.
Observed as a failure of NFS over udp (bad checksums on ip fragments)
when compiled with GCC 3.4.2.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
missing helper used by arch/i386/mm/highmem.c, which is pulled
into build on that configuration.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) registers.h is really needed there
b) include of asm-generic/termios should be under __KERNEL__
c) includes of asm-generic/{memory_model,page} should be under
__KERNEL (nothing in there that would work in userland)
d) a lot of stuff in ptrace.h should be under __KERNEL__.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: fix pb_fnmode and move it to generic HID
HID: fix hid-input mapping for Firefly Mini Remote Control
USB HID: fix hid_blacklist clash for 0x08ca/0x0010
HID: fix memleaking of collection
This is based on a patch by Eric W. Biederman, who pointed out that pid
namespaces are still fake, and we only have one ever active.
So for the time being, we can modify any code which could access
tsk->nsproxy->pid_ns during task exit to just use &init_pid_ns instead,
and move the exit_task_namespaces call in do_exit() back above
exit_notify(), so that an exiting nfs server has a valid tsk->sighand to
work with.
Long term, pulling pid_ns out of nsproxy might be the cleanest solution.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
[ Eric's patch fixed to take care of free_pid() too ]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 7a238fcba0 in
preparation for a better and simpler fix proposed by Eric Biederman
(and fixed up by Serge Hallyn)
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] Add new IDs to VIA AGP.
[AGPGART] Remove pointless assignment.
[AGPGART] Remove pointless typedef in ati-agp
[AGPGART] Prevent (unlikely) memory leak in amd_create_gatt_pages()
[AGPGART] intel_agp: restore graphics device's pci space early in resume
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
via82cxxx/pata_via: correct PCI_DEVICE_ID_VIA_SATA_EIDE ID and add support for CX700 and 8237S
ide: unregister idepnp driver on unload
ide: add missing __init tags to IDE PCI host drivers
ia64: add pci_get_legacy_ide_irq()
ide/generic: Jmicron has its own drivers now
atiixp.c: add cable detection support for ATI IDE
atiixp.c: sb600 ide only has one channel
atiixp.c: remove unused code
jmicron: fix warning
ide: update MAINTAINERS entry
do { } while(0) is not a good imitation of function returning void;
use ((void)0) instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin points out that page accounting on MIPS multiple ZERO_PAGEs
is not maintained by its move_pte, and could lead to freeing a ZERO_PAGE.
Instead of complicating that move_pte, just forget the minor optimization
when mremapping, and change the one thing which needed it for correctness
- filemap_xip use ZERO_PAGE(0) throughout instead of according to address.
[ "There is no block device driver one could use for XIP on mips
platforms" - Carsten Otte ]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4117/1: S3C2412: Fix writel() usage in selection code
[ARM] 4111/1: Allow VFP to work with thread migration on SMP
[ARM] 4112/1: Only ioremap to supersections if DOMAIN_IO is zero
[ARM] 4106/1: S3C2410: typo fixes in register definitions
[ARM] 4102/1: Allow for PHYS_OFFSET on any valid 2MiB address
[ARM] Fix AMBA serial drivers for non-first serial ports
[ARM] 4100/1: iop3xx: fix cpu mask for iop333
[ARM] Update mach-types
[ARM] Fix show_mem() for discontigmem
[ARM] 4096/1: S3C24XX: change return code form s3c2410_gpio_getcfg()
[ARM] 4095/1: S3C24XX: Fix GPIO set for Bank A
[ARM] 4092/1: i.MX/MX1 CPU Frequency scaling latency definition
[ARM] 4089/1: AT91: GPIO wake IRQ cleanup
[ARM] 4088/1: AT91: Unbalanced IRQ in serial driver suspend/resume
[ARM] 4087/1: AT91: CPU reset for SAM9x processors
[ARM] 4086/1: AT91: Whitespace cleanup
[ARM] 4085/1: AT91: Header fixes.
[ARM] 4084/1: Remove CONFIG_DEBUG_WAITQ
Apparently this broke due to missing `struct inode' declaration.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Noah Watkins <nwatkins@ittc.ku.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use __u8 rather than u8 in SIZE defines exported to userspace.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In file included from include/linux/crypto.h:26,
from crypto/cipher.c:17:
include/linux/uaccess.h: In function 'pagefault_disable':
include/linux/uaccess.h:18: error: dereferencing pointer to incomplete type
include/linux/uaccess.h: In function 'pagefault_enable':
include/linux/uaccess.h:33: error: dereferencing pointer to incomplete type
video_buf need PCI.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix exit race by splitting the nsproxy putting into two pieces. First
piece reduces the nsproxy refcount. If we dropped the last reference, then
it puts the mnt_ns, and returns the nsproxy as a hint to the caller. Else
it returns NULL. The second piece of exiting task namespaces sets
tsk->nsproxy to NULL, and drops the references to other namespaces and
frees the nsproxy only if an nsproxy was passed in.
A little awkward and should probably be reworked, but hopefully it fixes
the NFS oops.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The apple powerbook people are used to switch the pb_fnmode
setting at runtime through writing to sysfs, altering the
module parameter value. This was broken for them in 2.6.20-rc1
when generic HID layer was introduced, as the pb_fnmode flag
was made per-hiddevice, instead of global variable.
This patch moves the pb_fnmode module parameter from usbhid module
to hid module, but apart from that retains backward compatibility
with respect to changing the mode through sysfs.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The recent change for a new sysfs tree with card* object breaks the
/sys/class/sound tree if CONFIG_SYSFS_DEPRECATED is enabled.
The device in each entry doesn't point the correct device object:
/sys/class/sound
...
|-- pcmC0D0c
| |-- dev
| |-- device -> ../../../class/sound/card0
| |-- pcm_class
| |-- power
| | `-- wakeup
| |-- subsystem -> ../../../class/sound
| `-- uevent
Also, this change breaks some drivers (like sound/arm/*) referring
card->dev directly to obtain the device object for memory handling.
This patch reverts the semantics of card->dev to the former version,
which points to a real device object. The card* object is stored in a
new card->card_dev field, instead. The device parent is chosen either
card->dev or card->card_dev according to CONFIG_SYSFS_DEPRECATED to
keep the tree compatibility.
Also, card* isn't created if CONFIG_SYSFS_DEPRECATED is enabled. The
reason of card* object is a root of all beloing devices, and it makes
little sense if each sound device points to the real device object
directly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Monty Montgomery <xiphmont@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Culled from the VIA codedrop.
Also fixes up one ID used in amd64-agp to use the
VIA part number instead of the board name in its ID.
Signed-off-by: Dave Jones <davej@redhat.com>
This patch:
* Corrects the wrong device ID of PCI_DEVICE_ID_VIA_SATA_EIDE
from 0x0581 to 0x5324.
* Adds VIA CX700 and VT8237S support in drivers/ide/pci/via82cxxx.c
* Adds VIA VT8237S support in drivers/ata/pata_via.c
Signed-off-by: Josepch Chan <josephchan@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add pci_get_legacy_ide_irq() identical to the one used by i386/x86_64.
Fixes amd74xx driver build on ia64 (bugzilla bug #6644).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: nf_conntrack_pptp: fix NAT setup of expected GRE connections
[NETFILTER]: nf_nat_pptp: fix expectation removal
[NETFILTER]: nf_nat: fix ICMP translation with statically linked conntrack
[TCP]: Restore SKB socket owner setting in tcp_transmit_skb().
[AF_PACKET]: Check device down state before hard header callbacks.
[DECNET]: Handle a failure in neigh_parms_alloc (take 2)
[BNX2]: Fix 2nd port's MAC address.
[TCP]: Fix sorting of SACK blocks.
[AF_PACKET]: Fix BPF handling.
[IPV4]: Fix the fib trie iterator to work with a single entry routing tables
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
Fix Maple PATA IRQ assignment.
ahci: use 0x80 as wait stat value instead of 0xff
sata_via: style clean up, no indirect method call in LLD
ahci: fix endianness in spurious interrupt message
libata-sff: Don't call bmdma_stop on non DMA capable controllers
libata: implement ATA_FLAG_IGN_SIMPLEX and use it in sata_uli
ahci: improve and limit spurious interrupt messages, take#3
sata_via: don't diddle with ATA_NIEN in ->freeze
libata: set_mode, Fix the FIXME
libata hpt3xn: Hopefully sort out the DPLL logic versus the vendor code
libata cmd64x: whack into a shape that looks like the documentation
On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.
This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.
There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.
So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nfsd defines a type 'encode_dent_fn' which is much like 'filldir_t' except
that the first pointer is 'struct readdir_cd *' rather than 'void *'. It
then casts encode_dent_fn points to 'filldir_t' as needed. This hides any
other type mismatches between the two such as the fact that the 'ino' arg
recently changed from ino_t to u64.
So: get rid of 'encode_dent_fn', get rid of the cast of the function type,
change the first arg of various functions from 'struct readdir_cd *' to
'void *', and live with the fact that we have a little less type checking
on the calling of these functions now. Less internal (to nfsd) checking
offset by more external checking, which is more important.
Thanks to Gabriel Paubert <paubert@iram.es> for discovering this and
providing an initial patch.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a number of kernel-doc entries for header files in include/linux by
making sure they begin with the appropriate '/**' notation and use @var
notation.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A couple of the warnings will be followed by an Oops if they ever fire, so may
as well be BUG_ON. Another isn't obviously fatal but has never been known to
fire, so make it a WARN_ON.
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NFSd assumes that largest number of pages that will be needed for a
request+response is 2+N where N pages is the size of the largest permitted
read/write request. The '2' are 1 for the non-data part of the request, and 1
for the non-data part of the reply.
However, when a read request is not page-aligned, and we choose to use
->sendfile to send it directly from the page cache, we may need N+1 pages to
hold the whole reply. This can overflow and array and cause an Oops.
This patch increases size of the array for holding pages by one and makes sure
that entry is NULL when it is not in use.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes core dumps to include the vDSO vma, which is left out now.
It removes the special-case core writing macros, which were not doing the
right thing for the vDSO vma anyway. Instead, it uses VM_ALWAYSDUMP in the
vma; there is no need for the fixmap page to be installed. It handles the
CONFIG_COMPAT_VDSO case by making elf_core_dump use the fake vma from
get_gate_vma after real vmas in the same way the /proc/PID/maps code does.
This changes core dumps so they no longer include the non-PT_LOAD phdrs from
the vDSO. I made the change to add them in the first place, but in turned out
that nothing ever wanted them there since the advent of NT_AUXV. It's cleaner
to leave them out, and just let the phdrs inside the vDSO image speak for
themselves.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the VM_ALWAYSDUMP flag for vm_flags in vm_area_struct. This
provides a clean explicit way to have a vma always included in core dumps, as
is needed for vDSO's.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I wouldn't mind if CONFIG_COMPAT_VDSO went away entirely. But if it's there,
it should work properly. Currently it's quite haphazard: both real vma and
fixmap are mapped, both are put in the two different AT_* slots, sysenter
returns to the vma address rather than the fixmap address, and core dumps yet
are another story.
This patch makes CONFIG_COMPAT_VDSO disable the real vma and use the fixmap
area consistently. This makes it actually compatible with what the old vdso
implementation did.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements forwarding of SHUTDOWN intercepts from the guest on to
userspace on AMD SVM. A SHUTDOWN event occurs when the guest produces a
triple fault (e.g. on reboot). This also fixes the bug that a guest reboot
actually causes a host reboot under some circumstances.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 931731123a
We can't elide the skb_set_owner_w() here because things like certain
netfilter targets (such as owner MATCH) need a socket to be set on the
SKB for correct operation.
Thanks to Jan Engelhardt and other netfilter list members for
pointing this out.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's useful to have access to struct ipic handle that just got created
in ipic_init().
For example, if we want to setup an external IRQ with out
a device node we need access ipic->irqhost to create the virtual to HW
IRQ mapping and to set the IRQ sense. With this we can mimic the old
sense array concept that existed in arch/ppc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On x86-64, a put_user call using a 64-bit pointer and a constant value that
is > 0xffffffff will produce code that doesn't assemble. This patch fixes
the asm construct to use the Z constraint for 32-bit constants.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some uli controllers have stuck SIMPLEX bit which can't be cleared
with ata_pci_clear_simplex(), but the controller is capable of doing
DMAs on both channels simultaneously. Implement ATA_FLAG_IGN_SIMPLEX
which makes libata ignore the simplex bit and use it in sata_uli.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current lazy saving of the VFP registers is no longer possible
with thread migration on SMP. This patch implements a per-CPU
vfp-state pointer and the saving of the VFP registers at every context
switch. The registers restoring is still performed in a lazy way.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When set_mode() changed ->set_mode didn't adapt. This makes the needed
changes and removes the relevant FIXME case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix wrong checksum calculation on 64-bit MIPS
[MIPS] VPE loader: Initialize lists before they're actually being used ...
[MIPS] Fix reported amount of freed memory - it's in kB not bytes
[MIPS] vr41xx: need one more nop with mtc0_tlbw_hazard()
[MIPS] SMTC: Fix module build by exporting symbol
[MIPS] SMTC: Fix TLB sizing bug for TLB of 64 >= entries
[MIPS] Fix APM build
[MIPS] There is no __GNUC_MAJOR__
Prevent the call to invalidate_inode_pages2() from racing with file writes
by taking the inode->i_mutex across the page cache flush and invalidate.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the Oops in http://bugzilla.linux-nfs.org/show_bug.cgi?id=138
We shouldn't be calling rpc_release_task() for tasks that are not active.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 8e3d8433d8 ([NET]: MIPS
checksum annotations and cleanups) broke 64-bit MIPS.
The problem is the commit replaces some unsigned long with __be32. On
64bit MIPS, a __be32 (i.e. unsigned int) value is represented as a
sign-extented 32-bit value in a 64-bit argument register. So the
address 192.168.0.1 (0xc0a80001) is passed as 0xffffffffc0a80001 to
csum_tcpudp_nofold() but the asm code in the function expects
0x00000000c0a80001, therefore it returns a wrong checksum. Explicit
cast to unsigned long is needed to drop high 32bit.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
NEC VR4111 and VR4121 need one more nop with mtc0_tlbw_hazard().
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Trcd* bits of the S3C24xx BANKCON6 and BANKCON7 registers are misspelled in include/asm-arm/arch-s3c2410/regs-mem.h as Trdc*.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO bank A can only be output or a special
function, and the regs-gpio.h header has
mistakenly got this as input or output.
The mistake is carried on into the gpio.c
s3c2410_gpio_cfgpin() call which will set the
wrong value if S3C2410_GPIO_OUTPUT is passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A couple of whitespace cleanups, mainly in the AT91 header files.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two typo's where AT01_* was used instead of AT91_*.
[Patch from Wojtek Kaniewski]
Fix definition of AT91_SMC_EXNWMODE for the SAM9 processors.
[Patch from Wu Xuan]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds irq remapping hook. On interrupt mechanism on Beat,
when an irq outlet which has an id which is formerly used is created,
remapping the irq is required.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Struct pci_controller doesn't prepare for the dependent data of each
specific bus. This patch adds private member to struct pci_controller.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I often test new versions of glibc by doing:
LD_LIBRARY_PATH=/XXX/lib /XXX/lib/ld.so.1 <binary>
One test case ended up SEGV'ing. Upon closer inspection ld.so was loaded
at 0x8000000 (128MB) with the heap right after it. Since we normally
link binaries at 0x10000000 (256MB) we only had about 128MB of space for
the heap:
00100000-00103000 r-xp 00100000 00:00 0 [vdso]
08000000-0801e000 r-xp 00000000 00:01 33079 /lib/ld-2.5.so
0802d000-0802f000 rwxp 0001d000 00:01 33079 /lib/ld-2.5.so
0802f000-08050000 rwxp 0802f000 00:00 0 [heap]
0fe91000-0ffd9000 r-xp 00000000 00:01 33082 /lib/libc-2.5.so
0ffd9000-0ffe8000 ---p 00148000 00:01 33082 /lib/libc-2.5.so
0ffe8000-0ffea000 r--p 00147000 00:01 33082 /lib/libc-2.5.so
0ffea000-0ffed000 rwxp 00149000 00:01 33082 /lib/libc-2.5.so
10000000-10004000 r-xp 00000000 00:01 76 /bin/sleep
10013000-10014000 rwxp 00003000 00:01 76 /bin/sleep
ffb41000-ffb56000 rw-p ffb41000 00:00 0 [stack]
One way to fix this is move ELF_ET_DYN_BASE from 0x08000000 to 0x20000000.
This allows 128MB for the binary (hopefully enough for even the most
crazy c++ apps), and with our current layout we will grow the heap up
and the stack down, allowing potentially gigabytes of heap:
00100000-00103000 r-xp 00100000 00:00 0 [vdso]
0fe8a000-0ffd3000 r-xp 00000000 00:01 3350 /lib/tls/libc-2.3.6.so
0ffd3000-0ffe3000 ---p 00149000 00:01 3350 /lib/tls/libc-2.3.6.so
0ffe3000-0ffea000 r--p 00149000 00:01 3350 /lib/tls/libc-2.3.6.so
0ffea000-0ffee000 rwxp 00150000 00:01 3350 /lib/tls/libc-2.3.6.so
10000000-10004000 r-xp 00000000 00:01 76 /bin/sleep
10013000-10014000 rwxp 00003000 00:01 76 /bin/sleep
20000000-20018000 r-xp 00000000 00:01 3478 /lib/ld-2.3.6.so
20028000-20029000 r--p 00018000 00:01 3478 /lib/ld-2.3.6.so
20029000-2002a000 rwxp 00019000 00:01 3478 /lib/ld-2.3.6.so
2002a000-2004b000 rwxp 2002a000 00:00 0 [heap]
ffd67000-ffd7c000 rw-p ffd67000 00:00 0 [stack]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Initialize qc->pad_len for each new command. This ensures
that pad_len is not set to a stale value for zero data
length commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixup the inialization of qc->n_elem. It currently gets
initialized to 1 for commands that do not transfer any data.
Fix this by initializing n_elem to 0 and only setting to 1
in ata_scsi_qc_new when there is data to transfer. This fixes
some problems seen with SATA devices attached to ipr adapters.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
include/linux/if_tunnel.h is broken for user application
because it was changed to use __be32 which is required
to include linux/types.h in advance but didn't.
(This issue is found when building MIPL2 daemon. We are not sure this
is the last header to be fixed about __be32.)
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: TAKAMIYA Noriaki <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit d3dcc077bf,
include/linux/if_{addr,link}.h should be processed with unifdef.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of x_tables we accidentally broke compatibility
by defining IPT_TABLE_MAXNAMELEN to XT_FUNCTION_MAXNAMELEN instead of
XT_TABLE_MAXNAMELEN, which is two bytes larger.
On most architectures it doesn't really matter since we don't have
any tables with names that long in the kernel and the structure
layout didn't change because of alignment requirements of following
members. On CRIS however (and other architectures that don't align
data) this changed the structure layout and thus broke compatibility
with old iptables binaries.
Changing it back will break compatibility with binaries compiled
against recent kernels again, but since the breakage has only been
there for three releases this seems like the better choice.
Spotted by Jonas Berlin <xkr47@outerspace.dyndns.org>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the chunk as Out-of-the-Blue if we don't have
an endpoint. Otherwise discard it as before.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from net/netfilter/xt_state.c:13:
include/net/netfilter/nf_conntrack_compat.h: In function 'nf_ct_l3proto_try_module_get':
include/net/netfilter/nf_conntrack_compat.h:70: error: 'PF_INET' undeclared (first use in this function)
include/net/netfilter/nf_conntrack_compat.h:70: error: (Each undeclared identifier is reported only once
include/net/netfilter/nf_conntrack_compat.h:70: error: for each function it appears in.)
include/net/netfilter/nf_conntrack_compat.h:71: warning: control reaches end of non-void function
make[2]: *** [net/netfilter/xt_state.o] Error 1
make[1]: *** [net/netfilter] Error 2
make: *** [net] Error 2
A simple fix is to have nf_conntrack_compat.h #include <linux/socket.h>.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMTC pseudo-interrupts between TCs are deferred and queued if the target
TC is interrupt-inhibited (IXMT). In the first SMTC prototypes, these
queued IPIs were serviced on return to user mode, or on entry into the
kernel idle loop. The INSTANT_REPLAY option dispatches them as part of
local_irq_restore() processing, which adds runtime overhead (hence the
option to turn it off), but ensures that IPIs are handled promptly even
under heavy I/O interrupt load.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a confusion reiserfs has for a long time.
On release file operation reiserfs used to try to pack file data stored in
last incomplete page of some files into metadata blocks. After packing the
page got cleared with clear_page_dirty. It did not take into account that
the page may be mmaped into other process's address space. Recent
replacement for clear_page_dirty cancel_dirty_page found the confusion with
sanity check that page has to be not mapped.
The patch fixes the confusion by making reiserfs avoid tail packing if an
inode was ever mmapped. reiserfs_mmap and reiserfs_file_release are
serialized with mutex in reiserfs specific inode. reiserfs_mmap locks the
mutex and sets a bit in reiserfs specific inode flags.
reiserfs_file_release checks the bit having the mutex locked. If bit is
set - tail packing is avoided. This eliminates a possibility that mmapped
page gets cancel_page_dirty-ed.
Signed-off-by: Vladimir Saveliev <vs@namesys.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Chris Mason <mason@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current PDA code, which went in in post 2.6.19 has a flaw in that it
doesn't correctly cycle the GDT and %GS segment through the boot PDA,
the CPU PDA and finally the per-cpu PDA.
The bug generally doesn't show up if the boot CPU id is zero, but
everything falls apart for a non zero boot CPU id. The basically kills
voyager which is perfectly capable of doing non zero CPU id boots, so
voyager currently won't boot without this.
The fix is to be careful and actually do the GDT setups correctly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
hid-core.c: Adds GTCO CalComp Interwrite IPanel PIDs to blacklist
HID: put usb_interface instead of usb_device into hid->dev to fix udevinfo breakage
HID: add missing RX, RZ and RY enum values to hid-debug output
HID: hid/hid-input.c doesn't need to include linux/usb/input.h
HID: compilation fix when DEBUG_DATA is defined
HID: proper LED-mapping for SpaceNavigator
HID: update MAINTAINERS entry for USB-HID
HID: GEYSER4_ISO needs quirk
HID: fix some ARM builds due to HID brokenness - make USB_HID depend on INPUT
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Update defconfigs
[POWERPC] atomic_dec_if_positive sign extension fix
[POWERPC] Fix OF node refcnt underflow in 836x and 832x platform code
[POWERPC] Make it blatantly clear; mpc5200 device tree is not yet stable
[POWERPC] Fix broken DMA on non-LPAR pSeries
[POWERPC] Fix cell's mmio nvram to properly parse device tree
[POWERPC] Remove bogus sanity check in pci -> OF node code
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (5023): Fix compilation on ppc32 architecture
V4L/DVB (5071): Tveeprom: autodetect LG TAPC G701D as tuner type 37
V4L/DVB (5069): Fix bttv and friends on 64bit machines with lots of memory
V4L/DVB (5033): MSI TV@nywhere Plus fixes
V4L/DVB (5029): Ks0127 status flags
V4L/DVB (5024): Fix quickcam communicator driver for big endian architectures
V4L/DVB (5021): Cx88xx: Fix lockup on suspend
V4L/DVB (5020): Fix: disable interrupts while at KM_BOUNCE_READ
V4L/DVB (5019): Fix the frame->grabstate update in read() entry point.
On 64-bit machines, if an atomic counter is explicitly set to a
negative value, the atomic_dec_if_positive function will decrement and
store the next smallest value in the atomic counter, contrary to its
intended operation.
The comparison to determine if the decrement will make the result
negative was done by the "addic." instruction, which operates on a
64-bit value, namely the zero-extended word loaded from the atomic
variable. This patch uses an explicit word compare (cmpwi) and
changes the addic. to an addi (also changing "=&r" to "=&b" so that r0
isn't used, and addi doesn't become li).
This also fixes a bug for both 32-bit and 64-bit in that previously
0x80000000 was considered positive, since the result after
decrementing is positive. Now it is considered negative.
Also, I clarify the return value in the comments just to make it clear
that the value returned is always the decremented value, even if that
value is not stored back to the atomic counter.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This trivial change adds some missing enum values to the hid-debug output.
Signed-off-by: Simon Budig <simon@budig.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
libata didn't used to init qc->dma_dir to any specific value on qc
initialization and command translation path didn't set qc->dma_dir if
the command doesn't need data transfer. This made non-data commands
to have random qc->dma_dir.
This usually doesn't cause problem because LLDs usually check
qc->protocol first and look at qc->dma_dir iff the command needs data
transfer but this doesn't hold for all LLDs.
It might be worthwhile to rename qc->dma_dir to qc->data_dir as we use
the field to tag data direction for both PIO and DMA protocols.
This problem has been spotted by James Bottomley.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's a problem, pointed by Meelis Roos <mroos@linux.ee>, that, on ppc32 arch,
with some gcc versions (noticed with prerelease 4.1.2 20061115), compilation
fails, due the lack of __ucmpdi2 to do the required 64-bit comparision.
This patch takes some sugestions made by Andrew Morton <akpm@osdl.org>,
Stelian Pop <stelian@popies.net> and Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During development of SDHC support, it was discovered that the definition
for R6 was incorrect. This patch fixes that and patches the drivers that
do switch on the response type.
Signed-off-by: Philip Langdale <philipl@overt.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pavel Pisa <ppisa@pikron.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
Revert "ACPI: ibm-acpi: make non-generic bay support optional"
ACPI: update MAINTAINERS
ACPI: schedule obsolete features for deletion
ACPI: delete two spurious ACPI messages
ACPI: rename cstate_entry_s to cstate_entry
ACPI: ec: enable printk on cmdline use
ACPI: Altix: ACPI _PRT support
unionfs managed to hit this on s390. Some architectures use __ptr_t in their
FD_ZERO implementation. We don't have a __ptr_t. Switch them over to plain
old void*.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert bd_mount_mutex back to a semaphore so that xfs_freeze -f /mnt/newtest;
xfs_freeze -u /mnt/newtest works safely and doesn't produce lockdep warnings.
(XFS unlocks the semaphore from a different task, by design. The mutex
code warns about this)
Signed-off-by: Dave Chinner <dgc@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NFS: Fix race in nfs_release_page()
invalidate_inode_pages2() may find the dirty bit has been set on a page
owing to the fact that the page may still be mapped after it was locked.
Only after the call to unmap_mapping_range() are we sure that the page
can no longer be dirtied.
In order to fix this, NFS has hooked the releasepage() method and tries
to write the page out between the call to unmap_mapping_range() and the
call to remove_mapping(). This, however leads to deadlocks in the page
reclaim code, where the page may be locked without holding a reference
to the inode or dentry.
Fix is to add a new address_space_operation, launder_page(), which will
attempt to write out a dirty page without releasing the page lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Also, the bare SetPageDirty() can skew all sort of accounting leading to
other nasties.
[akpm@osdl.org: cleanup]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an oops experienced on the Cell architecture when init-time functions,
early_*(), are called at runtime. It alters the call paths to make sure
that the callers explicitly say whether the call is being made on behalf of
a hotplug even, or happening at boot-time.
It has been compile tested on ppc64, ia64, s390, i386 and x86_64.
Acked-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
+m is really correct for a RMW instruction, but some older gccs
error out. I finally gave in and ifdefed it.
This fixes compilation errors with some compiler version.
Signed-off-by: Andi Kleen <ak@suse.de>
Revert previous attempts at messing with the linux banner string and
simply use a separate format string for proc.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IP_CT_TCP_FLAG_CLOSE_INIT is a flag and should have a value of 0x4 instead
of 0x3, which is IP_CT_TCP_FLAG_WINDOW_SCALE | IP_CT_TCP_FLAG_SACK_PERM.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The included patch translates arpt_counters to xt_counters, making
userspace arptables compile against recent kernels.
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa:
[ALSA] version 1.0.14rc1
[ALSA] usbaudio - Fix kobject_add() error at reconnection
[ALSA] usb: usbmixer error path fix
[ALSA] _snd_cmipci_uswitch_put doesn't set zero flags
[ALSA] hda-codec - Fix NULL dereference in generic hda code
[ALSA] hda_intel: ALSA HD Audio patch for Intel ICH9
[ALSA] usb-audio: work around wrong frequency in CM6501 descriptors
[ALSA] Fix potential NULL pointer dereference in echoaudio midi
[ALSA] Audio: Add nvidia HD Audio controllers of MCP67 support to hda_intel.c
* 'merge' of master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix bugs in the hypervisor call stats code
[POWERPC] Fix corruption in hcall9
[POWERPC] iSeries: fix setup initcall
[POWERPC] iSeries: fix viopath initialisation
[POWERPC] iSeries: fix lpevents initialisation
[POWERPC] iSeries: fix proc/iSeries initialisation
[POWERPC] iSeries: fix mf proc initialisation
[POWERPC] disable PReP and EFIKA during make oldconfig
[POWERPC] Fix mpc52xx serial driver to work for arch/ppc again
[POWERPC] Don't include powerpc/sysdev/rom.o for arch/ppc builds
[POWERPC] Fix mpc52xx fdt to use correct device_type for sound devices
[POWERPC] 52xx: Don't use device_initcall to probe of_platform_bus
[POWERPC] Add legacy iSeries to ppc64_defconfig
[POWERPC] Update ppc64_defconfig
[POWERPC] Fix manual assembly WARN_ON() in enter_rtas().
[POWERPC] Avoid calling get_irq_server() with a real, not virtual irq.
[POWERPC] Fix unbalanced uses of of_node_put
[POWERPC] Fix bogus BUG_ON() in in hugetlb_get_unmapped_area()
There are several places in the futex code where a spin_lock is held
and still uaccesses happen. Deadlocks are avoided by increasing the
preempt count. The pagefault handler will then not take any locks
but will immediately search the fixup tables.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There were a few issues with the HCALL_STATS code:
- PURR cpu feature checks were backwards
- We iterated one entry off the end of the hcall_stats array
- Remove dead update_hcall_stats() function prototype
I noticed one thing while debugging, and that is we call H_ENTER (to set
up the MMU hashtable in early init) before we have done the cpu fixups.
This means we will execute the PURR SPR reads even on a CPU that isnt
capable of it. I wonder if we can move the CPU feature fixups earlier.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using device_initcall makes it happen for every platform that
compiles this file in. This is really bad, for obvious reasons.
Instead, we use the .init field of the machine description. If
the platform needs the hook to do something specific it can provides
its own function and call mpc52xx_declare_of_platform_devices from
there. If not, the mpc52xx_declare_of_platform_devices function can
directly be used as the init hook.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we switched over to the generic BUG mechanism we forgot to change
the assembly code which open-codes a WARN_ON() in enter_rtas(), so the
bug table got corrupted.
This patch provides an EMIT_BUG_ENTRY macro for use in assembly code,
and uses it in entry_64.S. Tested with CONFIG_DEBUG_BUGVERBOSE on ppc64
but not without -- I tried to turn it off but it wouldn't go away; I
suspect Aunt Tillie probably needed it.
This version gets __FILE__ and __LINE__ right in the assembly version --
rather than saying include/asm-powerpc/bug.h line 21 every time which is
a little suboptimal.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement optimized asm version of csum_partial_copy_nocheck,
csum_partial_copy_from_user and csum_and_copy_to_user which can do
calculate and copy in parallel, based on memcpy.S.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
fuse does not work on ARM due to cache incoherency issues - fuse wants
to use get_user_pages() to copy data from the current process into
kernel space. However, since this accesses userspace via the kernel
mapping, the kernel mapping can be out of date wrt data written to
userspace.
This can lead to unpredictable behaviour (in the case of fuse) or data
corruption for direct-IO.
This resolves debian bug #402876
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since get_user_pages() may be used with processes other than the
current process and calls flush_anon_page(), flush_anon_page() has to
cope in some way with non-current processes.
It may not be appropriate, or even desirable to flush a region of
virtual memory cache in the current process when that is different to
the process that we want the flush to occur for.
Therefore, pass the vma into flush_anon_page() so that the architecture
can work out whether the 'vmaddr' is for the current process or not.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iop33x gpio offset is correct in include/asm-arm/arch-iop33x/iop33x.h, but
include/asm-arm/hardware/iop3xx.h adds 4.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
o Relocatable bzImage support had got rid of CONFIG_PHYSICAL_START option
thinking that now this option is not required as people can build a
second kernel as relocatable and load it anywhere. So need of compiling
the kernel for a custom address was gone. But Magnus uses vmlinux images
for second kernel in Xen environment and he wants to continue to use
it.
o Restoring the CONFIG_PHYSICAL_START option for the time being. I think
down the line we can get rid of it.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the kernels later than 2.6.19 there is a regression that makes swsusp
fail if the resume device is not explicitly specified.
It can be fixed by adding an additional parameter to
mm/swapfile.c:swap_type_of() allowing us to pass the (struct block_device
*) corresponding to the first available swap back to the caller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current interrupt injection mechanism might delay an interrupt under
the following circumstances:
- if injection fails because the guest is not interruptible (rflags.IF clear,
or after a 'mov ss' or 'sti' instruction). Userspace can check rflags,
but the other cases or not testable under the current API.
- if injection fails because of a fault during delivery. This probably
never happens under normal guests.
- if injection fails due to a physical interrupt causing a vmexit so that
it can be handled by the host.
In all cases the guest proceeds without processing the interrupt, reducing
the interactive feel and interrupt throughput of the guest.
This patch fixes the situation by allowing userspace to request an exit
when the 'interrupt window' opens, so that it can re-inject the interrupt
at the right time. Guest interactivity is very visibly improved.
Signed-off-by: Dor Laor <dor.laor@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeffrey Altman, one of the gatekeepers of OpenAFS (the open source project
which inherited the Transarc/IBM AFS codebase) has requested that the magic
number 0x5346414F (little endian 'OAFS') be allocated for the f_type field
of the fsinfo structure on Linux:
https://lists.openafs.org/pipermail/openafs-info/2006-December/024829.html
Add it to include/linux/magic.h, mostly as a way of publishing this number
and ensuring that no other filesystem accidentally uses it.
Cc: Jeffrey Altman <jaltman@secure-endpoints.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some of the ACPI devices use the internal fake hids
which are exposed to userspace as devces' bus_id after sysfs conversion.
To make it more friendly, we convert them to more understandable strings.
For those devices w/o PNPids, we use "device:instance_no" as the bus_id
instead of "PNPIDNON:instance_no".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts the new (unambiguous) definition of the TCP `before'
relation. As pointed out in an example by Herbert Xu, there is
existing code which implicitly requires the old definition in order
to work correctly.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide ACPI _PRT support for SN Altix systems.
The SN Altix platform does not conform to the
IOSAPIC IRQ routing model, so a new acpi_irq_model
(ACPI_IRQ_MODEL_PLATFORM) has been defined. The SN
platform specific code sets acpi_irq_model to
this new value, and keys off of it in acpi_register_gsi()
to avoid the iosapic code path.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a proper prototype for x25_init_timers() in
include/net/x25.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] drivers/char/agp/sgi-agp.c: check kmalloc() return value
[AGPGART] Fix PCI-posting flush typo.
[AGPGART] fix detection of aperture size versus GTT size on G965
[AGPGART] Remove unnecessary flushes when inserting and removing pages.
[AGPGART] K8M890 support for amd-k8.
The WLAN_GET_SEQ_SEQ(seq) macro in ieee80211 is selecting the wrong region.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Of the possible SSP frame formats (FRF bits in SSCR0), only SSCR0_PSP is defined. Other possible formats are Motorola SPI (0<<4), TI SSP (1<<4) and Microwire (2<<4). Attached patch adds a definition SSCR0_TISSP.
This mode is used for the sound codec attached to the PXA272 SSP1 of some HTC PDA phones.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SSCR0_SlotsPerFrm macro writes a 3-bit value to bits [2:0], while the correct location of FRDC in SSCR0 is at bits [26:24]. This patch adds the missing "<< 24".
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have some new larger ia64 systems in HP that trip over the
ACPI_MAX_REFERENCE_COUNT limit which triggers a large number of these
debug messages:
ACPI Warning (utdelete-0397): Large Reference Count (XXX) in object e0000a0ff6797ab0 [20060707]
This was increased once in the past as described in this very brief thread:
http://www.mail-archive.com/linux-acpi@vger.kernel.org/msg00890.html
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Handle ISA devices with no 'regs' property.
[SPARC64]: Update defconfig.
[SPARC64]: Fix of_iounmap() region release.
[SPARC64]: Fix "mem=xxx" handling.
Don't add it there please; add it lower down inside the existing #ifdef
__KERNEL__. You just made the _userspace_ net.h include random.h, which
then fails to compile unless <asm/types.h> was already included.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver writer calls this, they generally expect that
all previous stores and modifications they've made will be
visible before netif_poll_enable() executes, so ensure this.
Noticed by Ben H.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to pass in the resource otherwise we cannot
release the region properly. We must know whether it is
an I/O or MEM resource.
Spotted by Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
fs/proc/base.c:1869: warning: initialization discards qualifiers from pointer target type
fs/proc/base.c:2150: warning: initialization discards qualifiers from pointer target type
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some issues were recently turned up with the current specification of what
it means for spi_transfer.tx_buf to be null, as part of transfers which are
(from the SPI protocol driver perspective) pure reads.
Specifically, that it seems better to change the TX behaviour there from
"undefined" to "will shift zeroes". This lets protocol drivers (like the
ads7846 driver) depend on that behavior. It's what most controller drivers
in the tree are already doing (with one exception and one case of driver
wanting-to-oops), it's what Microwire hardware will necessarily be doing,
and it removes an issue whereby certain security audits would need to
define such a value anyway as part of removing covert channels.
This patch changes the specification to require shifting zeroes, and
updates all currently merged SPI controller drivers to do so.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
