The sata_sis driver supports SATA and PATA ports. The broken support
of both types in one controller is fixed.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The commit d4b2bab4f2 added deadline support
to prereset and reset methods to libbata the pata_scc driver wasn't
converted. This patch is a naive attempt to bring this driver up to
scratch.
Build failures are:
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:870: error: too few arguments to function 'ata_std_prereset'
drivers/ata/pata_scc.c: In function 'scc_error_handler':
drivers/ata/pata_scc.c:916: warning: passing argument 2 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:916: warning: passing argument 3 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:871: warning: control reaches end of non-void function
On a releated note scc_bus_post_reset() is (AFACT) identical to
ata_bus_post_reset(), would a patch to make ata_bus_post_reset() assesable
to drivers be accepted?
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_via: Handle laptops via DMI
libata: -ENODEV during prereset isn't an error
libata: don't consider 0xff as port empty if SStatus is available
ata_piix: add short 40c quirk for Acer Aspire 2030, take #2
pata_sis: Fix and clean up some timing setups
hpt3x2n: Correct revision boundary
Oh the joy of saving a fraction of a cent using short 40 wire cables and
not faking 80wire
Teach the VIA driver that there are some systems we need to know are
magically wired for high speeds.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Francis Russell <FrancisRussell@btinternet.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During prereset, -ENODEV return from ata_wait_ready() is not an error.
This causes unnecessary bug message on controllers which uses 0xff to
indicate empty port. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers (sata_sil) use 0xff to indicate port not ready
status, not port empty. As libata interprets 0xff as port empty, this
causes unnecessary reset failure and retry. Don't consider 0xff as
port empty if SStatus is available and indicates that port is online.
Signed-off-by: tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Indan Zupancic <indan@nul.nu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acer Aspire 2023WLMi uses short 40c cable. Add quirk for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Steve H. <mail.pandor@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Rename sis_port_base to sis_old_port_base() so nobody uses it for new
generation controllers in error.
- Use byte size operations where it is cleaner for mode setup
- Fix a couple of masking errors on certai chip revs when setting speeds
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a revision that isn't correctly claimed as two drivers both go
for it: Fix the test accordingly. Noticed originally by Bill Nottingham.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mutex instead of binary semaphore in idt77252 driver.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the cpu irq mask define to include the timer irq.
Another flag check was setting up the timer bit in all cases so we
didn't notice the issue.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The stats update code in spider_net_pass_skb_up() is touching the skb
after it's been passed up to the stack. To avoid that, just update the
stats first.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The meth ethernet driver for the SGI IP32 aka O2 is so far still an old
style driver which does not use the device driver model. This is now
causing issues with some udev based gadgetry in debian-stable. Fixed by
converting the meth driver to a platform device.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
--
Fixes since previous patch:
o Fixed typo in meth_exit_module()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch has removed unnecessary dependency on VIA velocity config.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the following compiler warning (and warnings resulting from
the correction):
warning: 'fixed_mdio_register_device' defined but not used
Signed-off-by: Denver Gingerich <denver@ossguy.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(Originally sent to linux-usb-devel)
The attached patch adds the device IDs for the Belkin F5D5055 device.
Reported by Andy Juniper <ajuniper@freeuk.com>
Signed-off-by: David Hollis <dhollis@davehollis.com>
--
David Hollis <dhollis@davehollis.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix MODULE_DEVICE_TABLE() duplication in ucc_geth.c and ucc_geth_mii.c
for ucc_geth to be compiled as module.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since NAPI polling is disabled while ipoib_cm_dev_stop() is running,
ipoib_cm_dev_stop() must poll the CQ itself in order to see the
packets draining.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
time_after() was used backwards, so the timeout occurred immediately.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a typo, the driver was reporting the wrong number of "actual send
WRs" after ehca_create_qp().
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to initialize the owner bit of send queue WQEs to hardware
ownership whenever the QP is modified from reset to init, not just
when the QP is first allocated. This avoids having the hardware
process stale WQEs when the QP is moved to reset but not destroyed and
then modified to init again.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: add maintainer for ARM Primecell controller
mmc: add maintainer for iMX MMC interface
mmc: Add maintainers for TI OMAP MMC interface
mmc: mark unmaintained drivers
mmc: clean up unused parts of block driver
eh_timed_out call back (megasas_reset_timer) is used to throttle io
to the adapter when it is called the first time for a scmd.
The MEGASAS_FW_BUSY flag is set and can_queue reduced to 16.
The can_queue is restored from completion routine in following
two conditions : 5 seconds has elapsed and
the # of outstanding cmds in FW is < 17.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In case of Broadcom based Bluetooth devices, it is safe to always
send HCI_Reset as first command. This gives the advantage that
all HID Proxy versions will automatically work and don't need any
additional quirks anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allow in-place crypto operations. Also remove the coherent user flag
(we use it automagically now), and by default use the user written
key rather then the HW hidden key - this makes crypto just work without
any special considerations, and thats OK, since its our only usage
model.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Squash these:
drivers/isdn/hardware/eicon/message.c: In function 'api_put':
drivers/isdn/hardware/eicon/message.c:536: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'plci_free_msg_in_queue':
drivers/isdn/hardware/eicon/message.c:1035: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'data_b3_req':
drivers/isdn/hardware/eicon/message.c:3121: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c:3154: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'callback':
drivers/isdn/hardware/eicon/message.c:4060: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'nl_ind':
drivers/isdn/hardware/eicon/message.c:7137: warning: cast from pointer to integer of different size
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
squish these:
drivers/isdn/hardware/eicon/capifunc.c: In function 'TransmitBufferSet':
drivers/isdn/hardware/eicon/capifunc.c:192: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/capifunc.c: In function 'TransmitBufferGet':
drivers/isdn/hardware/eicon/capifunc.c:197: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c:198: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c:200: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c: In function 'TransmitBufferFree':
drivers/isdn/hardware/eicon/capifunc.c:205: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c:206: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c: In function 'sendf':
drivers/isdn/hardware/eicon/capifunc.c:304: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/capifunc.c:304: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/capifunc.c:321: warning: cast to pointer from integer of different size
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The omap_uwire controller driver handles SPI_CPHA incorrectly;
It should mean:
CPHA=0 ... sample at leading edge of clock
CPHA=1 ... sample at trailing edge of clock
This bug has been masked by inverse bugs in layered drivers;
and was uncovered by running some of them on non-OMAP hardware.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=7482.
It sets USB snooping on 4G space for PowerPC platforms without
CONFIG_NOT_COHERENT_CACHE defined.
Reported-by: Stefan Meyer <reyems@telkomsa.net>
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another coverity patch i forgot to resend, original thread here
http://marc.info/?l=linux-kernel&m=115144559823592&w=2
In case drive == N_DRIVE, we get one past the drive_params array.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as875) adds error-checking to the callers of hisax_register().
It also changes an error pathway in that routine, making it return an error
code rather than 0.
This fixes Bugzilla #7960.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Martin Bachem <info@colognechip.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding a drive to a linear array seems to have stopped working, due to changes
elsewhere in md, and insufficient ongoing testing...
So the patch to make linear hot-add work in the first place introduced a
subtle bug elsewhere that interracts poorly with older version of mdadm.
This fixes it all up.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible that real data or metadata follows the bitmap without full page
alignment.
So limit the last write to be only the required number of bytes, rounded up to
the hard sector size of the device.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a raid0 has a component device larger than 4TB, and is accessed on a 32bit
machines, then as 'chunk' is unsigned long,
chunk << chunksize_bits
can overflow (this can be as high as the size of the device in KB). chunk
itself will not overflow (without triggering a BUG).
So change 'chunk' to be 'sector_t, and get rid of the 'BUG' as it becomes
impossible to hit.
Cc: "Jeff Zheng" <Jeff.Zheng@endace.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason i2o_max_drivers must be a power of two. This patch
eliminates such a constraint.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maximum number of I2O drivers which could be registered is configurable by
max_drivers module parameter.
But the module parameter is ignored and default value (I2O_MAX_DRIVERS = 8)
is used in the loops to notify all registered drivers.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2o_driver_register() initalizes event queue for driver only when
drv->event is set. So similarly the event queue should be destroyed only
when drv->event is set in the error path. Otherwise destroy_workqueue()
will called with NULL.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
phantom, take care of pci posting
thanks to akpm for pointing this out
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
phantom's ioctl is often (4000 times a sec or so) invoked, don't acquire
BKL and block other processes.
Signed-off-by: Jiri Slaby <xslaby@phantom.fi.muni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
info->pseudo_palette was previously kmalloced. Do not overwrite it afterwards
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some small fixes for the imxfb framebuffer driver:
- remove ifndef for MX1FS2 platform which is not present in the kernel.
- REV, CLS, PS and SPL_SPR are only needed with some sharp displays.
Only setup the corresponding io pins when such a display is connected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Use the FB_SYS_* operations instead of the FB_CFB_* operations as the
actual frame buffer memory is part of system RAM
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compile warnings from w100fb.c. Attribute registration failure doesn't
stop the driver working so just warn about it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix 16-bit RGBA 4444 and 5551 modes (use fbset -rgba to set them)
- kill wmb() after each register write by PM3_SLOW_WRITE_REG
- kill inaccurate comments (leftovers from skeletonfb.c)
- kill PCI class restriction, now it is more general and shorter
- white spaces and other minor fixes and source reducing
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a possible barriers problem in RDAC_WR functions, then
remove redudant ones.
It also removes one unneeded register load from blitter function().
Signed-off-by: Krzysztof.Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch puts all SBUS/UPA selection under one option "SBUS/UPA
framebuffers" and moves all sparc specific drivers next to them in one group.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'ioc' should be deallocated if __copy_from_user fails (found by Coverity
- CID 1644).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Message size needs to be checked before copying, or bad things could
happen.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mpc5200 PSC SPI driver to actually work for CONFIG_PPC_MERGE
- s/mpc52xx/mpc5200/, as this was changed in device tree some time ago
- fix spi id detection
The move from 'ppc' to 'powerpc' didn't quite match the latest
kernel.org code.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Dragos Carp <dragos.carp@toptica.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few entries in ata_device_blacklist[] in libata-core.c
marked with HORKAGE_NODMA but are missing from drive_blacklist[]
in ide-dma.c. This patch makes the lists in sync.
Also remove a duplicated entry for "SanDisk SDP3B-64".
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Compiling with '-Wswitch-enum' I noticed following:
CC drivers/ide/ide-proc.o
drivers/ide/ide-proc.c: In function âproc_ide_read_imodelâ:
drivers/ide/ide-proc.c:54: warning: enumeration value âide_etrax100â not handled in switch
drivers/ide/ide-proc.c:54: warning: enumeration value âide_acornâ not handled in switch
How about the following patch?
Signed-off-by: Mika Kukkonen <mikukkon@iki.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out from customer reports to Red Hat and some PCI dumps that the
MegaIDE in RAID mode doesn't provide the drive tuning data that the
serverworks driver expects but sometimes does provide something that
fools the code.
For the RAID class case skip the oem setup and don't trust the BIOS data.
We then tune from scratch and this sorts it out. (This has been confirmed
on an afflicted IBM blade)
[libata serverworks.c never trusts the BIOS in the first place so is
accidentally immune]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add the IDE device ID to atiixp_pci_tbl struct in atiixp.c for ATI SB700.
From: Henry Su <henry.su@amd.com>
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If a QP is attached to a shared receive queue (SRQ), then it doesn't
have a receive queue (RQ). So don't allocate an RQ doorbell (or map a
doorbell from userspace for userspace QPs) for that QP.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (29 commits)
USB: Add support for Olimex arm-usb-ocd JTAG interface serial port
USB: Add support for Sierra Wireless Aircard 595U
USB: ldusb bugfix
USB: ftdi_sio: Add USB Product Id for OpenDCC
USB: fix ratelimit call semantics
USB: handle errors in power/level attribute
USB: make the autosuspend workqueue thread freezable
USB: Fix USB OHCI Subvendor for Toshiba Portege 4000
USB: usblp: Use correct DMA address in case of probe error
USB: Fix debug output of ark3116
USB: Onetouch - switch to using input_dev->dev.parent
USB: don't try to kzalloc 0 bytes
USB: remove short initial timeout for device descriptor fetch
USB: Deref URB after usbmon is done with it
USB: Remove duplicate IDs from option card driver
USB: auerswald: fix file release handler
USB: fsl_usb2_udc: Fix UMTI_WIDE support and a compile warning
USB: set the correct Interrupt interval in usb_bulk_msg
USB: New device PID for ftdi_sio driver
USB: remove unneeded WARN_ON
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ads7846 - SPI_CPHA mode bugfix
Input: ads7846 - document that it handles tsc2046 too
Input: input-polldev - add module info
Input: ucb1x00-ts - remove commented out code
Input: ucb1400_ts - use sched_setscheduler()
Input: ALPS - force stream mode
Input: iforce - minor clean-ups
Input: iforce - fix force feedback not working
Input: adbhid - do not access input_dev->private directly
Input: logips2pp - add type 72 (PS/2 TrackMan Marble)
Fix config warning related to select usage:
drivers/macintosh/Kconfig:117:warning: 'select' used by config symbol 'PMAC_APM_EMU' refers to undefined symbol 'SYS_SUPPORTS_APM_EMULATION'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The UCC_GETH Kconfig option in drivers/net/Kconfig had a line to select the
UCC_FAST option is arch/powerpc/sysdev/qe_lib/Kconfig, which is only used
on PowerPC builds. On other architectures, this would generated a warning.
The fix is to have UCC_FAST depend on UCC_GETH.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the serial port on Olimex arm-usb-ocd
JTAG interface.
The device appears as two serial ports, but the first one is reserved
for the JTAG interface. The JTAG interface can be used with OpenOCD
from userspace. For more information, please see:
http://openocd.berlios.de/web/http://www.olimex.com/dev/arm-usb-ocd.html
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the newly released Aircard 595U EVDO
modem to the Sierra Wireless driver (sierra.c) in kernel 2.6.21.
I suspect that my mailer may be mangling patches so let me know and
I'll try to resend it.
From: Danny Budik <dbudik@ist-traffic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem reported with consecutive reads in the ldusb
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the OpenDCC (www.opendcc.de)
model railway central unit. Applies to 2.6.21.1.
Signed-off-by: Guido Scholz <guido.scholz@bayernline.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as910) fixes a ratelimit modification so that the
original error-handling path will be followed even when the log-rate
limitation kicks in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as906) improves the error handling for the USB power/level
attribute file. If an error occurs, the original power-level settings
will be restored.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as881b) makes the ksuspend_usb_wq workqueue freezable. We
don't want a rogue workqueue thread running around, unexpectedly
suspending or resuming USB devices in the middle of a system sleep
transition.
This fixes Bugzilla #8498.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bug in an OHCI quirk handler for Portege 4000; the
Subvendor is 0x1179 (PCI_VENDOR_ID_TOSHIBA)
not 0x102f (PCI_VENDOR_ID_TOSHIBA_2)
bugid 8510
00:02.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller
[10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device [1179:0004]
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like the error path had a copy-paste error. The normal exit path
uses correct URB already.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix debug output. Previously, it would output "0xFFFFFFB0" on 32-bit
archs (and probably "0xFFFFFFFFFFFFFFB0" on 64-bits), because buf is
taken as signed char, which is promoted to signed int, while %x always
expects an unsigned int.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Also, do not access input_dev->private directly, use helpers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as907) prevents us from trying to allocate 0 bytes
when an interface has no endpoint descriptors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as905) removes a micro-optimization from the hub port
initialization code. Previously we had been using a short timeout on
the first attempt the read the device descriptor; now we will use the
standard timeout length.
It's not clear that the short timeout ever provided any benefit. And
now we know of one case where it actually hurts: The device can't meet
the short timeout and then it gets terminally confused.
This fixes Bugzilla #8444.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I haven't personally run across an oops because of this, but I feel safer
with this fix in place.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If this down_interruptible() does fail due to signal_pending() then the state
of the driver will get trashed in interesting ways, because userspace cannot
and will not retry the close().
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change PORT_WIDTH bit for UMTI_WIDE mode and fix a compile warning
introduced in last revision.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as902) fixes a mistake I introduced into usb_bulk_msg().
usb_fill_int_urb() already does the bit-shifting calculation for
high-speed Interrupt intervals; it shouldn't be done twice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Hello,
I need to use MaxStream's PKG-U modules which includes a ftdi sio chipset for
usb2serial communication, here are the patches for handling Maxstream's modules.
The VID & PID to use with the open-source driver are provided on the CD-ROM
bundled with the modules.
From: Neil Superna ARMSTRONG <superna@na-prod.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as883) removes an out-of-date WARN_ON from the main HCD
endpoint-disable routine. The warning is triggered whenever an
endpoint is disabled while the root hub is suspended. In the past
that may not have been legal, but it definitely is legal now. Merely
unbinding a USB driver will do it.
Furthermore, I've never seen any occurrences of this warning that
really did signal an actual bug or error condition. At this point it
has outlived its purpose.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch (as879) ties up some loose ends from an earlier patch.
These are things I didn't think to include at the time but which
clearly belonged there.
If an autosuspend fails because driver activity races with
the autosuspend call, restart the autosuspend timer.
When a device is resumed by an external request, it counts
as device activity and should update the last_busy time so
that the next autoresume won't occur immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as882) fixes a problem with the EHCI BIOS handoff. On my
machine, the BIOS configures the controller and the handoff fails,
leaving the controller configured. During resume-from-disk, this
confuses ehci-hcd into thinking that the controller has not been
tampered with.
The problem is fixed by turning off the Configured Flag whenever a
BIOS handoff is attempted, whether it succeeds or not.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the issue of drivers claiming multiple interfaces. Operations
are stopped as soon as an interface is suspend and resumed only as
all interfaces have been resumed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround another device firmware bug, wherein CDC descriptors get
placed in a wrong place never previously observed in the wild.
Fix a bug where a seeming RNDIS device returns a bogus response during
device initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial fix for bogosity in the ftdi-elan and u132-hcd drivers ... these
have no business including with the internals of other drivers, much less
doing so in a broken way!!
A previous patch resolved one build fix, this resolves another...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Sitecom WL-117 is another "driverless" ZD1211 device where the virtual
windows driver CD must be ejected before the WLAN device appears.
zd1211rw takes care of the ejecting, but usb-storage must be told not to claim
the device.
From: Matthew Davidson <mj.davidson@gmail.com>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the transfer of allocating the descriptor in attach and no longer in open
was incomplete resulting in a memory leak coverity spotted. This fix
is against the patch set you posted.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit [1] the SPI mode is set to 1, but it should be 0. As stated
in the commit, ads784x samples the data on the rising edge. SPI mode 1
samples on the falling edge [2] though.
The root cause of this is a bug in the omap_uwire code, which treats
CPHA=1 incorrectly; so these two bugs cancel each other out on one
of the main regression test platforms for this driver.
[1] kernel.org GIT 7937e86a70
[2] http://en.wikipedia.org/wiki/Serial_Peripheral_Interface_Bus
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The TSC2046 is an updated version of the ADS7846 ... mention that in
the Kconfig helptext and driver source.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is required to load it as a module, as GPL-compatible
license is necessary to use workqueues.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix Philips UCB1400 driver to use sched_setscheduler() instead of setting
the fields of task_struct directly.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ALPS appears to need SETSTREAM command after reset, otherwise it
does not produce any data. Now that we do not request stream mode
by default individual drivers need to take care of it.
[Jason Riedy <ejr@cs.berkeley.edu> - fix oops]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use an interrupt URB to send force-feedback data to the device
instead of a bulk URB. This was broken since 2.6.18.
Signed-off-by: Johann Deneux <johann.deneux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are several cases where the fusion driver uses the logical || to
try to do an arithmetical or ... fix by replacing with |.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A bug in the ov7670 sensor causes it to introduce noise unless the CLKRC
register is rewritten *after* setting the image mode. Naturally,
resetting CLKRC in this way will cause other modes to fail. So
carefully poke the register only when indicated.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The proper method for powering down the sensor on OLPC systems has
changed somewhat; in particular, the sensor must be powered down
completely (rather than simply told to power down) or the associated
"camera active" LED will stay on.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow to use SECAM-BG with the FI1216MF tuner.
The selection is done with the secam=B module argument.
The default behaviour should be the same as before.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Every so often, the driver will call asd_clear_nexus to clean out a task.
It is supposed to be the case that the CLEAR NEXUS does not go on the done
list until after the task itself has been put on the done list, but for
some reason this doesn't always happen. Thus, the
wait_for_completion_timeout call times out, and we return success. This
makes libsas free the task even though the task hasn't completed, leading
to a BUG_ON message from aic94xx_hwi.c around line 341. We should return
failure from asd_clear_nexus so that libsas tries again; at a bare minimum
it shouldn't be freeing active tasks. I _think_ this will fix one of
the SCB timeout crash problems (though I've not been able to reproduce
it lately...)
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Tue, 2007-05-22 at 06:51 -0500, Bob Tracy wrote:
> Second try: originally reported this back on April 17th. 2.6.X
> kernel builds started failing after I upgraded my compiler from
> gcc-3.3.X to gcc-3.4.6:
>
> make -C drivers/scsi/aic7xxx/aicasm
> (...)
> gcc -I/usr/include -I. aicasm.c aicasm_symbol.c aicasm_gram.c aicasm_macro_gram.c aicasm_scan.c aicasm_macro_scan.c -o aicasm -ldb
> aicasm_gram.y:1948: error: conflicting types for 'yyerror'
> aicasm_gram.tab.c:3004: error: previous implicit declaration of 'yyerror' was here
> aicasm_macro_gram.y:162: error: conflicting types for 'mmerror'
> aicasm_macro_gram.tab.c:1196: error: previous implicit declaration of 'mmerror' was here
Fix is to add a prototype for yyerror and mmerror to the relevant files.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Under some conditions associated with the unclean transition to kdump,
the aacraid adapters will view the array as foreign and not export it to
prevent access and data manipulation. The solution is to submit a commit
configuration to export the devices since this is a expected behavior
when transitioning to a kdump kernel.
This patch adds the aacraid.reset_devices flag and when either this or
the global reset_devices flag is set, ensures that a commit config is
issued and extends the startup_timeout if it is set less than 5 minutes.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as909) fixes a couple of refcounting errors in the sd
driver's suspend and resume methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
dvb-core is not started early enough when device drivers that use dvb are
compiled in so dvb_register_device fails (silently) since dvb_class is
NULL, this runs dvb_init using subsys_initcall instead of module_init.
dvb_register_device will now check the return value of class_device_create.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reverted the change to struct v4l2_pix_format. I completely missed that
this struct was used by existing ioctls so that changing it broke the ABI.
I will have to think of another way of setting the top/left coordinates
but for now this change is reverted to preserve compatibility.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix for the following build warning:
CC drivers/i2c/busses/i2c-s3c2410.o
drivers/i2c/busses/i2c-s3c2410.c: In function 's3c24xx_i2c_probe':
drivers/i2c/busses/i2c-s3c2410.c:839: warning: format '%ld' expects type 'long int', but argument 4 has type 'resource_size_t'
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent legacy drivers from issuing uevents for device creation/removal,
so that userspace can't cause modprobing loops for them. This became a
problem for some legacy PC drivers. I can't easily see it becoming an
issue with I2C legacy drivers, but consistency-in-paranoia seems likely
to be a good thing here. For usable i2c-level driver model uevents, just
switch to a new-style driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
skb could have been freed by then. Also, in libertas_upload_rx_packet(),
skb->protocol is initialized by eth_type_trans().
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NULL checks should be performed before the dereference.
Spotted by the Coverity checker.
Signed-off-by: Eugene Teo <eteo@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In libertas_process_rxed_packet() and process_rxed_802_11_packet() the
skb is dereferenced after being passed to netif_rx (called from
libertas_upload_rx_packet). Spotted by Coverity (1658, 1659).
Also, libertas_upload_rx_packet() unconditionally returns 0 so the error
check is dead code - might as well take it out and change the signature.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: bump versions
libata: Trim trailing whitespace
libata: Kiss post_set_mode goodbye
ata_piix: clean up
pata_hpt366: Enable bits are unreliable so don't use them
libata: Add Seagate STT20000A to DMA blacklist.
ahci: disable 64bit dma on sb600
With cable methods in place we don't need a custom error handler for SATA
so get rid of it
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various people had problems with both old and new IDE when hpt366 enable
bits started getting honoured. It turns out they are not reliable so
don't rely on them
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
http://bugzilla.kernel.org/show_bug.cgi?id=1044 points out an
additional hard disk that doesn't handle DMA transfers correctly.
This patch is the libata variant of the earlier patch to drivers/ide/
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The spin_unlock_irq() invocation in lance_start_xmit() has no matching
locking request. The call is already protected by netif_tx_lock, so
remove the statement.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Herbert Xu wrote:
"netif_poll_enable can only be called if you've previously called
netif_poll_disable. Otherwise a poll might already be in action
and you may get a crash like this."
Removing the call to netif_poll_enable in e1000_open should fix this issue,
the only other call to netif_poll_enable is in e1000_up() which is only
reached after a device reset or resume.
Bugzilla: http://bugzilla.kernel.org/show_bug.cgi?id=8455https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=240339
Tested by Doug Chapman <doug.chapman@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/cm: Improve local id allocation
IPoIB/cm: Fix SRQ WR leak
IB/ipoib: Fix typos in error messages
IB/mlx4: Check if SRQ is full when posting receive
IB/mlx4: Pass send queue sizes from userspace to kernel
IB/mlx4: Fix check of opcode in mlx4_ib_post_send()
mlx4_core: Fix array overrun in dump_dev_cap_flags()
IB/mlx4: Fix RESET to RESET and RESET to ERROR transitions
IB/mthca: Fix RESET to ERROR transition
IB/mlx4: Set GRH:HopLimit when sending globally routed MADs
IB/mthca: Set GRH:HopLimit when building MLX headers
IB/mlx4: Fix check of max_qp_dest_rdma in modify QP
IB/mthca: Fix use-after-free on device restart
IB/ehca: Return proper error code if register_mr fails
IPoIB: Handle P_Key table reordering
IB/core: Use start_port() and end_port()
IB/core: Add helpers for uncached GID and P_Key searches
IB/ipath: Fix potential deadlock with multicast spinlocks
IB/core: Free umem when mm is already gone
The IB CM uses an idr for local id allocations, with a running counter
as start_id. This fails to generate distinct ids if
1. An id is constantly created and destroyed
2. A chunk of ids just beyond the current next_id value is occupied
This in turn leads to an increased chance of connection request being
mis-detected as a duplicate, sometimes for several retries, until
next_id gets past the block of allocated ids. This has been observed
in practice.
As a fix, remember the last id allocated and start immediately above it.
This also fixes a problem with the old code, where next_id might
overflow and become negative.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SRQ WR leakage has been observed with IPoIB/CM: e.g. flipping ports on
and off will, with time, leak out all WRs and then all connections
will start getting RNR NAKs. Fix this in the way suggested by spec:
move the QP being destroyed to the error state, wait for "Last WQE
Reached" event and then post WR on a "drain QP" connected to the same
CQ. Once we observe a completion on the drain QP, it's safe to call
ib_destroy_qp.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
a) platorm_driver_probe(...) instead of platform_driver_register(&driver);
b) set bfin_spi_enable and bfin_spi_disable static
c) Why is the width flag a u32?
d) maybe use dev_dbg() instead of pr_debug()
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
properly setting up and respecting the read_status_mask / ignore_status_mask fields of the serial core
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass the number of WQEs for the send queue and their size from userspace
to the kernel to avoid having to keep the QP size calculations in sync
between the kernel driver and libmlx4. This fixes a bug seen with the
current mlx4_ib driver and current libmlx4 caused by a difference in the
calculated sizes for SQ WQEs. Also, this gives more flexibility for
userspace to experiment with using multiple WQE BBs for a single SQ WQE.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
wr->opcode is invalid if it's >= ARRAY_SIZE(mlx4_ib_opcode), not just
strictly >.
This was spotted by the Coverity checker (CID 1643).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't overrun fname[] array when decoding device flags.
This was spotted by the Coverity checker (CID 1642).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the IB spec, a QP can be moved from RESET back to RESET
or to the ERROR state, but mlx4 firmware does not support this and
returns an error if we try. Fix the RESET to RESET transition by
just returning 0 without doing anything, and fix RESET to ERROR by
moving the QP from RESET to INIT with dummy parameters and then
transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the IB spec, a QP can be moved from RESET to the ERROR
state, but mthca firmware does not support this and returns an error if
we try. Work around this FW limitation by moving the QP from RESET to
INIT with dummy parameters and then transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Global CM packets used by rmda_cm were being sent with a GRH:hopLimit
of zero, causing them to be dropped by the router. The problem is a
missing initialization of the hop_limit field in mthca_read_ah(),
which was called by build_mlx_header() when sending a MAD on QP1.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
max_qp_dest_rdma is already in natural units - no need to shift. This
was discovered by a test that deliberately requests more outstanding
atomic operation than the device supports.
Found by Sagi Rotem at Mellanox.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the return code of ehca_register_mr() to ENOMEM if the corresponding
firmware call fails due to out of resources. Some other error codes
were explicitly mapped to EINVAL -- just remove those cases so they
get mapped to the default case, which already returns EINVAL anyway.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SM reconfiguration or failover possibly causes a shuffling of the values
in the P_Key table. Right now, IPoIB only queries for the P_Key index
once when it creates the device QP, and hence there are problems if the
index of a P_Key value changes. Fix this by using the PKEY_CHANGE event
to trigger a recheck of the P_Key index.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up ib_query_port() and ib_modify_port() slightly by using the
just-added start_port() and end_port() helpers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add ib_find_gid() and ib_find_pkey() functions that use uncached device
queries. The calls might block but the returns are always up-to-date.
Cache P_Key and GID table lengths in core to avoid extra port info queries.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep found the following potential deadlock between mcast_lock and
n_mcast_grps_lock: mcast_lock is taken from both interrupt context and
process context, so spin_lock_irqsave() must be used to take it.
n_mcast_grps_lock is only taken from process context, so at first it
seems safe to take it with plain spin_lock(); however, it also nests
inside mcast_lock, and hence we could deadlock:
cpu A cpu B
ipath_mcast_add():
spin_lock_irq(&mcast_lock);
ipath_mcast_detach():
spin_lock(&n_mcast_grps_lock);
<enter interrupt>
ipath_mcast_find():
spin_lock_irqsave(&mcast_lock);
spin_lock(&n_mcast_grps_lock);
Fix this by using spin_lock_irq() to take n_mcast_grps_lock.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Free umem when task's mm is already destroyed by the time
ib_umem_release gets called.
Found by Dotan Barak at Mellanox.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Watchdog driver for the Kendin/Micrel KS8695 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix an Oops in the cciss driver caused by system shutdown while a filesystem
on a cciss device is still active. The cciss_remove_one function only
properly removes the device if the device has been cleanly released by its
users, which is not the case when the pci_driver.shutdown method is called.
This patch adds a new cciss_shutdown function to better match the pattern
used by various SCSI drivers: deactivate device interrupts and flush caches.
It also alters the cciss_remove_one function to match and readds the
__devexit annotation that was removed when cciss_remove_one was serving as
the pci_driver.shutdown method.
Signed-off-by: Gerald Britton <gbritton@alum.mit.edu>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] tcrypt: Add missing error check
[CRYPTO] padlock: Make CRYPTO_DEV_PADLOCK a tristate again
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (32 commits)
[POWERPC] Remove build warnings in windfarm_core
[POWERPC] Pass per-file CFLAGs for platform specific op codes
[POWERPC] Correct #endif comment
[POWERPC] Fix ppc_rtas_progress_show()
[POWERPC] Fix sed command lines for zlib source construction
[POWERPC] Specify GNUTARGET on $(AR) invocations
[POWERPC] Make sure device node type/name is not NULL on hot-added nodes
[POWERPC] Small fixes for the Ebony device tree
[POWERPC] Fix warning on UP
[POWERPC] cell_defconfig: Disable cpufreq and pmi
[POWERPC] Fix IO space on PCI buses created from of_platform
[POWERPC] Add spinlock to request_phb_iospace()
[POWERPC] Fix make rules for treeImage.initrd
[POWERPC] Remove warning in mpic.c
[POWERPC] Update pasemi_defconfig
[POWERPC] pasemi: CONFIG_GENERIC_TBSYNC no longer needed
[POWERPC] Update iseries_defconfig
[POWERPC] Wire up some more syscalls
[POWERPC] Fix bug adding properties with flatdevtree.c's ft_set_prop()
[POWERPC] Remove fixup_bigphys_addr() for arch/powerpc to avoid link error
...
Turning it into a boolean was unnecessary and caused ALGAPI to be
pinned down as a boolean to. This patch makes it a tristate again.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With STANDBYDOWN tracking added, libata.spindown_compat isn't
necessary anymore. If userspace shutdown(8) issues STANDBYNOW, libata
warns. If userspace shutdown(8) doesn't issue STANDBYNOW, libata does
the right thing. Userspace can tell whether kernel supports spindown
by testing whether sysfs node manage_start_stop exists as before.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As with all other drivers, sata_nv's hpriv is allocated with
devm_kzalloc() and there's no need to free it explicitly. Kill
nv_remove_one() which incorrectly used kfree() instead of devm_kfree()
and use ata_pci_remove_one() directly.
Original fix is from Peer Chen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv
driver is unnecessary. Also the wildcard sometimes cause sata_nv driver to
be loaded for AHCI controllers,which is not as expected.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_msi failure is a normal event so we should not print any error.
Going over the code I spotted a missing pci_disable_msi() leak when irq
allocation fails. The whole code also needed a cleanup, so I combined the
two different calls to pci_request_irq into a single call making this
look a lot better. All #ifdef CONFIG_PCI_MSI's have been removed.
Compile tested with both CONFIG_PCI_MSI enabled and disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_msi calls can fail for normal operational reasons. Driver
should not print an error message in that case. Fix a leak that leaves
msi enabled if pci_request_irq fails. We can remove CONFIG_PCI_MSI
ifdefs alltogether
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix for driver on System-p
This patch will fix a ping issue on system-p
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Adhiraj Joshi <adhiraj@netxen.com>
Signed-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spidernet was the driver I original did all the node-aware netdevice
allocation for, but after a year it still hasn't hit mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware must not see that is given ownership of a buffer until it is
completely written, and when the driver receives ownership of a buffer,
it must ensure that any other reads to the buffer reflect its final
state. Thus, I/O barriers are added where required.
Without this patch, I have observed GCC reordering the setting of
bdp->length and bdp->status in gfar_new_skb. Hardware reordering
was also theoretically possible.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix link speed detection change.
Thanks to Stefan Roese <sr@denx.de> for finding this bug.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Original patch is from Jeff Haran <jharan@brocade.com> with my minor style
fixes. His comments follow:
The first problem was in the function that configures the PHY for
autonegotiation, genmii_setup_aneg(). The original code does a
read/modify/write of the autonegotiation advertizement register (reg 4),
followed by a read/modify/write of the control register (reg 0). While
the original code follows the proper procedure as per reading the IEEE
specs, what I found is that on at least one PHY model (National DP83843)
the read of the control register comes back with the soft reset bit set
(bit 15). Because of the read/modify/write operation, this causes the
write to write a 1 back to the reset bit, which initiates a software
reset of the PHY. This software reset causes the PHY to return to its
power up state which advertizes all modes of operation, thus negating
the write to the autoneg advertizement register. The modification is to
spin reading the control register until the soft reset bit is clear
before doing the modify/write.
The second problem was in the function that configures the PHY for
forced operation, genmii_setup_forced(). The original code initiates a
software reset operation via a write of a 1 to bit 15 of the control
register (reg 0), but then proceeds to do a second write to that same
register without waiting until that reset bit is cleared by the PHY
itself (which according to the IEEE specs indicates that the PHY reset
is complete). This is a violation of how one is supposed to use this
software reset feature of these PHYs and I believe was the cause of
mysterious, difficult to reproduce link failures that we've observed on
some of our systems that use this driver. The fix is to modify the
function so that it spins waiting for the reset bit to clear after doing
the soft reset and before doing the subsequent write.
Signed-off-by: Jeff Haran <jharan@brocade.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: Stephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.
This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.
It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.
[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make drivers/rtc/Kconfig be clearer about what the various "interfaces"
actually mean, by showing path names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typo which breaks build. How did that happen?
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refine SCREEN_INFO sanity check for vgacon initialization.
Checking video mode field only to see whenever SCREEN_INFO is
initialized is not enougth, in some cases it is zero although
a vga card is present. Lets additionally check cols and lines.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Strip __cpuinit[data] from Node <-> PXM routines and supporting data
structures. Also make pxm_to_node_map and node_to_pxm_map local to the
numa acpi module.
This fixes a bug triggered by the following conditions:
- boot on a machine with a SLIT table defined
- kernel is configured w/ CONFIG_HOTPLUG_CPU=n
- cat /sys/devices/system/node/node*/distance
This will cause an oops by calling into a freed memory section.
In particular, on x86_64, __node_distance calls node_to_pxm().
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/macintosh/windfarm_core.c: In function 'wf_register_control':
drivers/macintosh/windfarm_core.c:219: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/windfarm_core.c: In function 'wf_register_sensor':
drivers/macintosh/windfarm_core.c:329: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
![](/avatar/362e80bc9fa0d4c6d6e2a8a86ae5d0d0?size=56 "Neil \\"Superna\\" ARMSTRONG"){kind=small}
