Commit graph

140 commits

Author SHA1 Message Date
Stephen Hemminger
8d3d35b4e2 [PATCH] sky2: phy power problems on 88e805X chips
On the 88E805X chipsets (used in laptops), the PHY was not getting powered
out of shutdown properly. The variable reg1 was getting reused incorrectly.
This is probably the cause of the bug.
	http://bugzilla.kernel.org/show_bug.cgi?id=6471

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-10 08:30:48 -04:00
Stephen Hemminger
caa0371e8b [PATCH] sky2: NAPI poll fix
When sky2 driver gets lots of received packets at once, it can get stuck.
The NAPI poll routine gets called back to keep going, but since no IRQ bits
are set it doesn't make progress.

Increase version, since this is serious enough problem that I want to be
able to tell new from old problems.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-17 13:27:46 -04:00
Stephen Hemminger
22e1170310 [PATCH] sky2: optimize receive restart
When the driver handles multiple packets per NAPI poll, it is
better to reload the receive ring, then tell the hardware. Otherwise,
under packet storm with flow control, the driver/hardware will degrade
down to one packet getting through per pause-exchange.

Likewise on transmit, don't wakeup until a little more than minimum
ring space is available.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-12 18:39:22 -04:00
Stephen Hemminger
afa195da45 [PATCH] sky2: PHY power on delays
The documentation says we need to wait after turning on the PHY.
Also, don't enable WOL by default.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-12 18:39:21 -04:00
Stephen Hemminger
6a5706b99c [PATCH] sky2: NAPI suspend/resume of dual port cards
The changes to handle suspend/resume didn't handle the case where
a dual port card has the first port down, but the second is running.
In this driver, all NAPI polling is done on the primary port.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-12 18:39:21 -04:00
Stephen Hemminger
59139528c8 [PATCH] sky2: sky2_reset section mismatch
Since sky2_reset gets call from sky2_resume it shouldn't be tagged
with devinit.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-12 18:39:21 -04:00
Herbert Xu
89114afd43 [NET] gso: Add skb_is_gso
This patch adds the wrapper function skb_is_gso which can be used instead
of directly testing skb_shinfo(skb)->gso_size.  This makes things a little
nicer and allows us to change the primary key for indicating whether an skb
is GSO (if we ever want to do that).

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-08 13:34:32 -07:00
Thomas Gleixner
1fb9df5d30 [PATCH] irq-flags: drivers/net: Use the new IRQF_ constants
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-02 13:58:51 -07:00
Jörn Engel
6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Greg Kroah-Hartman
7c7459d1f9 [PATCH] 64bit resource: fix up printks for resources in networks drivers
This is needed if we wish to change the size of the resource structures.

Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-27 09:23:58 -07:00
Herbert Xu
7967168cef [NET]: Merge TSO/UFO fields in sk_buff
Having separate fields in sk_buff for TSO/UFO (tso_size/ufo_size) is not
going to scale if we add any more segmentation methods (e.g., DCCP).  So
let's merge them.

They were used to tell the protocol of a packet.  This function has been
subsumed by the new gso_type field.  This is essentially a set of netdev
feature bits (shifted by 16 bits) that are required to process a specific
skb.  As such it's easy to tell whether a given device can process a GSO
skb: you just have to and the gso_type field and the netdev's features
field.

I've made gso_type a conjunction.  The idea is that you have a base type
(e.g., SKB_GSO_TCPV4) that can be modified further to support new features.
For example, if we add a hardware TSO type that supports ECN, they would
declare NETIF_F_TSO | NETIF_F_TSO_ECN.  All TSO packets with CWR set would
have a gso_type of SKB_GSO_TCPV4 | SKB_GSO_TCPV4_ECN while all other TSO
packets would be SKB_GSO_TCPV4.  This means that only the CWR packets need
to be emulated in software.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-23 02:07:29 -07:00
Stephen Hemminger
88d113601c [PATCH] sky2: netconsole suspend/resume interaction
A couple of fixes that should prevent crashes when using netconsole and
suspend/resume. First, netconsole poll routine shouldn't run unless the
device is up; second, the NAPI poll should be disabled during suspend.

This is only an issue on sky2, because it has to have one NAPI poll
routine for both ports on dual port boards. Normal drivers use
netif_rx_schedule_prep and that checks for netif_running.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-17 10:52:12 -07:00
Stephen Hemminger
eb35cf60e4 [PATCH] sky2: stop/start hardware idle timer on suspend/resume
The resume bug was caused not by an early interrupt but because the idle
timeout was not being stopped on suspend.  Also disable hardware IRQ's
on suspend.  Will need to revisit this with hotplug?

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-13 13:16:41 -07:00
Stephen Hemminger
8ab8fca207 [PATCH] sky2: save/restore base hardware irq during suspend/resume
The hardware should be fully shut off during suspend, and the base
irq mask restored during resume.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-13 13:16:41 -07:00
Stephen Hemminger
26ec43f132 [PATCH] sky2: fix hotplug detect during poll
If the poll routine detects no hardware available, it needs to dequeue
it self from the network poll list. Linus didn't understand NAPI.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-13 13:16:41 -07:00
Stephen Hemminger
f05267e7de [PATCH] sky2: don't hard code number of ports
It is cleaner, to not loop over both ports if only one exists.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-13 13:16:41 -07:00
Stephen Hemminger
2ccc99b7b7 [PATCH] sky2: set_power_state should be void
The set power state function is cleaner if it doesn't return anything.
The only caller that could fail is in suspend() and it can check the argument
there.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-13 13:16:40 -07:00
Linus Torvalds
d374c1c128 [sky2] Fix sky2 network driver suspend/resume
This fixes two independent problems: it would not save the PCI state on
suspend (and thus try to resume a nonexistent state on resume), and
while shut off, if an interrupt happened on the same shared irq, the irq
handler would react very badly to the interrupt status being an invalid
all-ones state.

Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-12 12:53:27 -07:00
Stephen Hemminger
a1433ac4ab [PATCH] sky2: fix jumbo packet support
The truncate threshold calculation to prevent receiver from getting stuck
was incorrect, and it didn't take into account the upper limit on bits
in the register so the jumbo packet support was broken.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-24 00:36:09 -04:00
Stephen Hemminger
c9b84dcac6 [PATCH] sky2 version 1.4
Need to track impact of this group of changes.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20 00:15:39 -04:00
Stephen Hemminger
86fba6342d [PATCH] sky2: force NAPI repoll if busy
If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20 00:15:39 -04:00
Stephen Hemminger
86a31a759f [PATCH] sky2: more fixes for Yukon Ultra
Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20 00:15:39 -04:00
Stephen Hemminger
2d2a387199 [PATCH] Subjec: sky2, skge: correct PCI id for DGE-560T
The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.

Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20 00:15:39 -04:00
Stephen Hemminger
ee7abb04df [PATCH] sky2: allow dual port usage
If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed.  This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.

A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.

This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20 00:15:39 -04:00
Stephen Hemminger
843a46f423 sky2: prevent dual port receiver problems
When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.

It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-15 12:35:01 -07:00
Linus Torvalds
6314410dd1 Merge branch 'upstream' of master.kernel.org:/pub/scm/linux/kernel/git/shemminger/netdev-2.6
* 'upstream' of master.kernel.org:/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
  sis900: phy for FoxCon motherboard
  dl2k: use DMA_48BIT_MASK constant
  phy: mdiobus_register(): initialize all phy_map entries
  sky2: ifdown kills irq mask
2006-05-10 14:59:29 -07:00
Stephen Hemminger
f4ea431bb7 sky2: ifdown kills irq mask
Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-10 14:03:41 -07:00
Stephen Hemminger
6d4b0f617d sky2: version 1.3
Update version number, to track changes.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:28 -07:00
Stephen Hemminger
ed6d32c7a9 Add more support for the Yukon Ultra chip found in dual core centino laptops.
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.

Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:27 -07:00
Stephen Hemminger
72cb852920 sky2: synchronize irq on remove
Need to make sure interrupt is not racing with unregister of
network device.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:27 -07:00
Stephen Hemminger
e71ebd7327 sky2: dont write status ring
It is more efficient not to write the status ring from the
processor and just read the active portion.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:27 -07:00
Stephen Hemminger
01bd75645f sky2: edge triggered workaround enhancement
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:27 -07:00
Stephen Hemminger
cb5d954730 sky2: use mask instead of modulo operation
Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:27 -07:00
Stephen Hemminger
f55925d7eb sky2: tx ring index mask fix
Mask for transmit ring status was picking up bits from the
unused sync ring.  They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:25 -07:00
Stephen Hemminger
1e5f1283a2 sky2: status irq hang fix
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:24 -07:00
Stephen Hemminger
d324031245 sky2: backout NAPI reschedule
This is a backout of earlier patch.

The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
2006-05-08 16:00:23 -07:00
Stephen Hemminger
bdf9c27d02 [PATCH] sky2: version 1.2
Update to version 1.2

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-26 06:19:46 -04:00
Stephen Hemminger
98712e5e33 [PATCH] sky2: reset function can be devinit
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-26 06:19:46 -04:00
Stephen Hemminger
4a15d56f78 [PATCH] sky2: use ALIGN() macro
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-26 06:19:45 -04:00
Stephen Hemminger
d27ed38765 [PATCH] sky2: add fake idle irq timer
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-26 06:19:45 -04:00
Stephen Hemminger
734cbc363b [PATCH] sky2: reschedule if irq still pending
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.

The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-26 06:19:45 -04:00
Stephen Hemminger
43f2f10444 [PATCH] sky2: bad memory reference on dual port cards
Sky2 driver will oops referencing bad memory if used on
a dual port card.  The problem is accessing past end of
MIB counter space.

Applies for both 2.6.17 and 2.6.16 (with fuzz)

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-12 18:11:23 -04:00
Stephen Hemminger
5636f72794 [PATCH] dlink pci cards using wrong driver
This patch fixes the problem of some Dlink cards picking the wrong
driver.  It looks like these cards use Yukon 1 chipset, not Yukon 2.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-12 18:04:03 -04:00
Stephen Hemminger
15240072ac [PATCH] sky2: dont need to use dev_kfree_skb_any
Transmit buffers are always freed with interrupts enabled (softirq),
so we can just call dev_kfree_skb.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-23 17:13:53 -05:00
Stephen Hemminger
050ff18016 [PATCH] sky2: Fix RX stats
Unicast packets are shown as multicast, real multicast packets are missing.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-23 17:13:53 -05:00
Stephen Hemminger
d26045404c [PATCH] sky2: typo in last stats patch
Typo in last stats patch.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-23 17:13:53 -05:00
Stephen Hemminger
eadfa7ddca [PATCH] sky2: more ethtool stats
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-22 20:30:45 -05:00
Stephen Hemminger
8368f31c8f [PATCH] sky2 version 1.1
Set version to 1.1

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-21 16:00:53 -05:00
Stephen Hemminger
d257924e85 [PATCH] sky2: handle all error irqs
The hardware has additional error trap interrupt bits.  I have never seen
them trigger, but if they do, it looks like this might be useful.

Signed-off-by: Stephen Hemminger <shemminger@osdl.rog>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-21 16:00:53 -05:00
Stephen Hemminger
8f24664da6 [PATCH] sky2: transmit recovery
This patch decodes state and revovers from any races in the transmit
timeout and NAPI logic. It should never trigger, but if it does then
do the right thing.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-21 16:00:52 -05:00