The code for mapping special 4k pages on kernels using a 64kB base
page size was missing the code for doing the RPN (real page number)
manipulation when inserting the hardware PTE in the secondary hash
bucket. It needs the same code as has already been added to the
code that inserts the HPTE in the primary hash bucket. This adds it.
Spotted by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes up the defconfig for various sh7751r based boards
by updating them to the single cpu subtype CONFIG_CPU_SUBTYPE_SH7751R.
The following sh4 boards are updated: hs7751rvoip, landisk, lboxre2,
systemh, titan.
The current defconfigs with two subtypes defined trigger a configuration
bug which result in kernel configurations with missing board support
code. We end up with kernels without board code and with generic machvec
only.
So we need this patch to make sure the board code gets compiled in.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure cf support is enabled on R2D-PLUS but disabled
on R2D-1. Without this fix R2D-1 boards hang on bootup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- Disable CONFIG_SH_DMA to avoid boot up freeze on R2D-1
- Disable CONFIG_SH_STANDARD_BIOS to support R2D-PLUS boot loaders
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updated the snapgear defconfig to get a booting kernel.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a missing =m constraint to the EDD-probing code, that could have
caused improper dead-code elimination.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add memory operand constraint and write-only modifier to the inline
assembly to effect the writing of the EDID block to boot_params.edid_info.
Without this, gcc would think the EDID query was dead code and would
eliminate it.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] ITC: Reduce rating for ITC clock if ITCs are drifty
[IA64] SN2: Fix up sn2_rtc clock
[IA64] Fix wrong access to irq_desc[] in iosapic_register_intr().
[IA64] Fix possible race in destroy_and_reserve_irq()
[IA64] Fix registered interrupt check
[IA64] Remove a few duplicate includes
[IA64] Allow smp_call_function_single() to current cpu
[IA64] fix a few section mismatch warnings
Enable the MB93090 motherboard's MB86943 PCI arbiter correctly by assigning to
the register rather than comparing against it. This is required to support
bus mastering.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure to reduce the rating of the ITC clock if ITCs are drifty. If they
are drifting then we have not synchronized the ITC values, nor are we doing
the jitter compensation (useless since drift may increase the differentials
arbitrarily).
Without this patch it is possible that the ITC clock becomes selected as
the system clock on systems with drifty ITCs which will result in
nanosleep hanging.
One can still select the itc clock manually on such systems via
clocksource=itc
(Produces nice hangs on SGI Altix.)
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If the sn2_rtc clock is present then it is a must have since sn2_rtc
provides a synchronized time source on Altix systems. So elevate
the priority to 450. Otherwise the ITC would take precendence. Altix
systems currently do not boot because the ITC clocksource is broken. It
seems to assume that ITCs are synchronized and as a result nanosleep
hangs (may be fixed in a different patch).
While we are at it: Remove the sn2_mc definition. The sn2_rtc has a fixed
address. No point in reading the address from memory. Removing it avoids
touching one cacheline.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In error path we must unlock irq_desc[irq].lock before we change
'irq'.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
SH-X3 has the FPU exceptions on different vectors completely,
patch in do_fpu_state_restore() to the proper vectors.
Results in a much happier userspace.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When reading the cached TTB value and extracting the pgd, we
accidentally applied a __va() to it and bumped it off in to bogus
space which ended up causing multiple faults in the error path.
Fix it up so unhandled faults don't do strange and highly unorthodox
things when oopsing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fault-nommu defines the page fault handler stubs for SH-3/4 parts,
but is not needed on SH-2/SH-2A now that the entry code has been
logically separated.
Add it in for SH-3 and SH-4 explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We were missing the trace_hardirqs_on() instrumentation in the nommu
case, resync with the MMU version of the page fault handler to have
this behaving consistently. Also explicitly re-enable IRQs now that
the assembly code isn't doing it for us any more.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the SH-3/4 TLB access violation path we were enabling IRQs before
the call in to trace_hardirqs_on(), which ended up triggering:
if (DEBUG_LOCKS_WARN_ON(!irqs_disabled()))
return;
in kernel/lockdep.c:2031. Fix this up by removing the early re-enable,
we were already re-enabling IRQs post-trace_hardirqs_on() already, so
the semantics are now as was initially intended.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] EDD: Fix the computation of the MBR sector buffer
[x86 setup] Newline after setup signature failure message
x86 boot code comments typos
C files should include the header files that prototype their functions.
Eliminates a sparse warning:
warning: symbol 'check_bugs' was not declared. Should it be static?
Signed-off-by: Josh Triplett <josh@kernel.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
C files should include the header files that prototype their functions.
Eliminates a sparse warning:
warning: symbol 'check_bugs' was not declared. Should it be static?
Signed-off-by: Josh Triplett <josh@kernel.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On make install I get the this error:
...
sh /work/crazy/linux-git/linux-2.6/arch/i386/boot/install.sh
2.6.22-g4eb6bf6b arch/i386/boot/bzImage System.map "/boot"
/work/crazy/linux-git/linux-2.6/arch/i386/boot/install.sh: line 54:
/etc/lilo/install: No such file or directory
make[1]: *** [install] Error 127
...
I don't use and don't have lilo installed on this system. The attached
patch fixes the problem for me.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/i386/kernel/apm.c: In function 'apm_init':
arch/i386/kernel/apm.c:2240: warning: format '%lx' expects type 'long
unsigned int', but argument 3 has type 'u32'
apm_info.bios.offset is of type 'u32'.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add $(LIBS_Y) to get lib/lib.a so srm_printk is present.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current 2.6.23-rc1+git, make bootimage gives the following warning while
compiling arch/alpha/boot/main.c. The patch below fixes the warning by
casting callback argument explicitly to void*. The original value comes from
START_ADDR macro and is clearly numeric so only cast it for the callback.
CC arch/alpha/boot/main.o
arch/alpha/boot/main.c: In function 'load':
arch/alpha/boot/main.c:135: warning: passing argument 3 of 'callback_read' makes pointer from integer without a cast
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current 2.6.23-rc1+git, make bootimage gives the following warnings while
compiling objstrip.c. The patch below fixes these warnings by casting strncmp
argument to char * - it does not seem feasible to change its type in struct
elfhdr.
HOSTCC arch/alpha/boot/tools/objstrip
arch/alpha/boot/tools/objstrip.c: In function 'main':
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strlen' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strlen' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strlen' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strncmp' differ in signedness
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current 2.6.23-rc1+git, make bootimage gives the following warnings while
compiling mkbb.c. The patch below fixes these warnings by using the proper
include for exit() and using appropriate printf format.
HOSTCC arch/alpha/boot/tools/mkbb
arch/alpha/boot/tools/mkbb.c: In function 'main':
arch/alpha/boot/tools/mkbb.c:95: warning: implicit declaration of function 'exit'
arch/alpha/boot/tools/mkbb.c:95: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:102: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:110: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:117: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
arch/alpha/boot/tools/mkbb.c:118: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:125: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
arch/alpha/boot/tools/mkbb.c:126: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:143: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:148: warning: incompatible implicit declaration of built-in function 'exit'
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 7e92b4fc34. It broke Sébastien Dugué's
machine and Jeff said (persuasively)
This seems like it will break decades-long-working stuff, in favor of
breaking new ground in our favorite area, "trusting the BIOS."
It's just not worth it for serial ports, IMO. Serial ports are something
that just shouldn't break at this late stage in the game. My new Intel
platform boxes don't even have serial ports, so I question the value of
messing with serial port probing even more... because... just wait a year,
and your box won't have a serial port either! :)
I certainly don't object to the use of platform devices (or isa_driver),
but the probe change seems questionable. That's sorta analagous to
rewriting the floppy driver probe routine. Sure you could do it... but why
risk all that damage and go through debugging all over again?
It seems clear from this report that we cannot, should not, trust BIOS for
something (a) so simple and (b) that has been working for over a decade.
Much discussion ensued and we've decided to have another go at all of this.
Cc: Sébastien Dugué <sebastien.dugue@bull.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused TIF_NOTIFY_RESUME flag for all processor architectures. The
flag was not used excecpt on IA-64 where the patch replaces it with
TIF_PERFMON_WORK.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following section mismatch warnings:
WARNING: o-alpha/vmlinux.o(.text+0x1a4d4): Section mismatch: reference to .init.text:free_area_init (between 'paging_init' and 'srm_paging_stop')
WARNING: o-alpha/vmlinux.o(.text+0x1a4dc): Section mismatch: reference to .init.text:free_area_init (between 'paging_init' and 'srm_paging_stop')
One instance of paging_init() was declared __init but not the other one -
used by defconfig. Fixed by declaring the second instance ___init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous DEBUG_SHIRQ patch missed one case. The console doesn't
set its host descriptors non-blocking.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix section mismatch warnings:
these functions are called only from __init functions.
WARNING: vmlinux.o(.text+0x1861c): Section mismatch: reference to .init.text:free_bootmem (between 'free_tce_table' and 'build_tce_table')
WARNING: vmlinux.o(.text+0x187e5): Section mismatch: reference to .init.text:__alloc_bootmem_low (between 'alloc_tce_table' and 'kretprobe_trampoline_holder')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local variable "covered" is used without initialization in i386
acpi-cpufreq driver. The initial value of covered should be 0. The bug
will cause memory leak when hit. The following patch fixes this bug.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the other archs, there is more factoring of smp call code, and more care
in the use of get_cpu(). That can be a follow-up MIPS patch.
Signed-off-by: Peter Watkins <pwatkins@sicortex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/kernel/machine_kexec.c: In function 'machine_kexec':
arch/mips/kernel/machine_kexec.c:54: warning: assignment makes integer from pointer without a cast
arch/mips/kernel/machine_kexec.c:70: warning: assignment makes integer from pointer without a cast
arch/mips/kernel/machine_kexec.c:81: warning: format '%08x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unlike the current code suggests, the RaQ1 actually has an UART. Only
the Qube1 (Qube 2700) lacks one.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes some duplicate includes from arch/mips/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The new type of irq handler remove a parameter (struct pt_regs *),but
someone forgot to supply it.
Signed-off-by: Dajie Tan <jiankemeng@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pmc-sierra/yosemite/smp.c: In function 'titan_mailbox_irq':
arch/mips/pmc-sierra/yosemite/smp.c:112: warning: 'status' may be used uninitialized in this function
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pmc-sierra/yosemite/i2c-yosemite.c: In function 'titan_i2c_xfer':
arch/mips/pmc-sierra/yosemite/i2c-yosemite.c:98: warning: 'data' may be used uninitialized in this function
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit e436d80085
Author: Ingo Molnar <mingo@elte.hu>
Date: Thu Jul 19 21:28:35 2007 +0200
[PATCH] sched: implement cpu_clock(cpu) high-speed time source
broke the build of several MIPS platforms which were already using the
symbol cpu_clock for the own purposes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
linux/arch/mips/pci/fixup-tx4938.c:21:5: warning: symbol 'pci_get_irq' was not declared. Should it be static?
linux/arch/mips/pci/fixup-tx4938.c:76: warning: passing argument 1 of 'pci_get_irq' discards qualifiers from pointer target type
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When comparing a pointer, it's clearer to compare it to NULL than to 0.
Here is an excerpt of the semantic patch:
@@
expression *E;
@@
E ==
- 0
+ NULL
@@
expression *E;
@@
E !=
- 0
+ NULL
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: akpm@linux-foundation.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some BIOSes require that sector buffers not cross 64K
boundaries. As a result, we compute a dynamic address on the
setup heap. Unfortunately, this address computation was just
totally wrong.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
End the "No setup signature found..." with a newline (the puts
routine will automatically add a carriage return.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This deals with a sun4c issue caused by commit b6a2fea393:
mm: variable length argument support.
The new way the code works means that sun4c_update_mmu_cache gets
called before a context has been selected, which results in invalid
operation of the underling mm code.
Simply ignoring update requests when there is no valid context solves
the problem.
Signed-off-by Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23:
sh: Fix fs.h removal from mm.h regressions.
sh: fix get_wchan() for SH kernels without framepointers
sh: arch/sh/boot - fix shell usage
rtc: rtc-sh: Correct sh_rtc_set_time() for some SH-3 parts.
sh: remove support for sh7300 and solution engine 7300
sh: Add sh to the CC_OPTIMIZE_FOR_SIZE dependencies.
sh: Kill off virt_to_bus()/bus_to_virt().
sh: sh-sci - fix SH7708 support
sh: Restrict DSP support to specific CPUs.
sh: Silence sq compile warning on sh4 nommu.
sh: Kill the rest of the SE73180 cruft.
sh: remove support for sh73180 and solution engine 73180
sh: remove old broken pint code
sh: Reclaim beginning of P3 space for vmalloc area.
sh: Fix Dreamcast DMA issues.
sh: Add kmap_coherent()/kunmap_coherent() interface for SH-4.
Needs interrupt.h:
CC arch/sh64/kernel/irq_intc.o
arch/sh64/kernel/irq_intc.c: In function 'make_intc_irq':
arch/sh64/kernel/irq_intc.c:179: error: implicit declaration of function 'disable_irq_nosync'
make[1]: *** [arch/sh64/kernel/irq_intc.o] Error 1
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently, destroy_and_reserve_irq() sets irq_status[irq] UNUSED using
clear_irq_vector() and sets irq_status[irq] RSVD using reserve_irq().
But there is a race window because vector_lock is once released between
them. This patch fixes this race window.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that interrupts are not initialized correctly at PCI
hotplug or driver reloading time.
By vector domain change, the iosapic_rte_info structure was changed to
be on the iosapic_intr_info[irq].rtes list even after the interrupts
are unregistered. So iosapic_intr_info[irq].rtes list must not be
checked to see if there are registered interrupts (RTEs) on the
irq. We must check iosapic_intr_info[irq].count counter instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes a few duplicate includes from arch/ia64/
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This removes the requirement for callers to get_cpu() to check in simple
cases. i386 and x86_64 already received a similar treatment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the following section mismatch warnings:
WARNING: vmlinux.o(.text+0x41902): Section mismatch: reference to .init.text:__alloc_bootmem (between 'ia64_mca_cpu_init' and 'ia64_do_tlb_purge')
WARNING: vmlinux.o(.text+0x49222): Section mismatch: reference to .init.text:__alloc_bootmem (between 'register_intr' and 'iosapic_register_intr')
WARNING: vmlinux.o(.text+0x62beb2): Section mismatch: reference to .init.text:__alloc_bootmem_node (between 'hubdev_init_node' and 'cnodeid_get_geoid')
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix show_stack() when stack argument is NULL.
[SPARC]: Fix serial console node string creation.
[SPARC]: Mark SBUS framebuffer ioctls as IGNORE in compat_ioctl.c
[SPARC64]: asm-sparc64/floppy.h needs linux/pci.h
[SPARC64]: Fix conflicts in SBUS/PCI/EBUS/ISA DMA handling.
[VIDEO]: Fix OOPS in all SBUS framebuffer drivers.
[SPARC64]: Handle mostek clock type in mini_rtc driver.
[PARTITION]: Sun/Solaris VTOC table corrections
[SPARC]: Fix floppy on some sun4c systems.
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
[PARTITION] MSDOS: Fix Sun num_partitions handling.
[SPARC]: Update defconfig.
Commit 296699de6b broke building APM
support if CONFIG_PM_SLEEP is not set.
Reported by Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Simplified a bit as suggested by Rafael. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the m32r build after the commit "Remove fs.h from mm.h"
was merged (commit 4e950f6f01).
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It didn't handle that case at all, and now dump_stack()
can be implemented directly as show_stack(current, NULL)
Signed-off-by: David S. Miller <davem@davemloft.net>
The string setting code depends upon the original value of the
"skip" variable, not the one that gets modified by the node
traversal loop.
Based upon a patch by Mark Fortescue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.
Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.
Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.
This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't provide fake PCI config space for sun4u.
Also, put back the funny host controller space handling that
at least Sabre needs. You have to read PCI host controller
registers at their nature size otherwise you get zeros instead
of correct values.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: Len Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Fix sclp_vt220 error handling.
[S390] cio: Reorganize initialization.
[S390] cio: Make CIO_* macros safe if dbfs are not available.
[S390] cio: Clean up messages.
[S390] Fix IRQ tracing.
[S390] vmur: fix diag14_read.
[S390] Wire up sys_fallocate.
[S390] add types.h include to s390_ext.h
[S390] cio: Remove deprecated rdc/rcd.
[S390] Get rid of new section mismatch warnings.
[S390] sclp: kill unused SCLP config option.
[S390] cio: Remove remains of _ccw_device_get_device_number().
[S390] cio: css_sch_device_register() can be made static.
[S390] Improve __smp_call_function_map.
[S390] Convert to smp_call_function_single.
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Input Serio: Blackfin doesnt support I8042 - make sure it doesnt get selected
Blackfin arch: add BF54x I2C/TWI TWI0 driver support
Blackfin On-Chip RTC driver update for supporting BF54x
Blackfin Ethernet MAC driver: fix bug Report returned -ENOMEM upwards (in case L1/uncached memory alloc fails)
Blackfin arch: add error message when IRQ no available
Blackfin arch: Initialize the exception vectors early in the boot process
Blackfin arch: fix a compiling warning about dma-mapping
Blackfin arch: switch to using proper defines this time THREAD_SIZE and PAGE_SIZE instead of just PAGE_SIZE everywhere
Blackfin arch: fix bug which unaligns the init thread's stack and causes the current macro to fail.
Blackfin arch: Load P0 before storing through it
Blackfin arch: fix KGDB bug, dont forget last parameter.
Blackfin arch: add selections for BF544 and BF542
Blackfin arch: use bfin_read_SWRST() now that BF561 provides it
Blackfin arch: setup aliases for some core Core A MMRs
This fixes the jornada720.c file :
* ifdef for CONFIG_SA1100_JORNADA720_SSP since we dont want to include anything not selected in menyconfig.
* add documentation for init for future reference
* change platform driver name from jornada720_mcu ->
jornada_ssp.
* change maintainer in file.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When comparing a pointer, it's clearer to compare it to NULL than to 0.
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Signed-off-by: Tony Luck <tony.luck@intel.com>
b716395e2b added code to handle
a compatability issue with 32bit quota tools, but the new compat
routines are only needed when CONFIG_COMPAT=y (and with this set
to 'n' there are compilation problems since some new typedefs are
not visible).
Reported by Doug Chapman. Fix tuned by a cast of thousands (Andi,
Andreas, Arthur, HPA, Willy)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Forgot to adjust this one with the acpi autoloading patches
in commit 8c8eb78f67
Acked-by: Myron Stowe <myron.stowe@hp.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If a machine check is pending and the external or I/O interrupt handler
returns to userspace io_mcck_pending is going to call s390_handle_mcck.
Before this happens a call to TRACE_IRQS_ON was already made since we
know that we are going back to userspace and hence interrupts will be
enabled. So there was an indication that interrupts are enabled while
in reality they are still disabled.
s390_handle_mcck will do a local_irq_save/restore pair and confuse
lockdep which later complains about inconsistent irq tracing.
To solve this just call trace_hardirqs_off before calling
s390_handle_mcck and trace_hardirqs_on afterwards.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements support of fallocate system call on s390(x)
platform. A wrapper is added to address the issue which s390 ABI has with
the arguments of this system call.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no need to disable bottom halves when holding call_lock. Also
this could imply that it is legal to call smp_call_function* from
bh context, which it is not.
Also test if func will be executed locally before disabling
and aterwards enabling interrupts again. It's not necessary to disable
and enable interrupts each time __smp_call_function_map gets called.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_call_function_single now has the same semantics as s390's
smp_call_function_on. Therefore convert to the *single variant
and get rid of some architecture specific code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix wrong return value in parse_vector_domain().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64's acpi_gsi_to_irq() function assumes irq == vector. But in
fact irq can be different from vector. This patch fix this wrong
assumption.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add some sanity checks into __bind_irq_vector().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (21 commits)
[POWERPC] spusched: Fix initial timeslice calculation
[POWERPC] spufs: Fix incorrect initialization of cbe_spu_info.spus
[POWERPC] Fix Maple platform ISA bus
[POWERPC] Make pci_iounmap actually unmap things
[POWERPC] Add function to check if address is an IO port
[POWERPC] Fix Pegasos keyboard detection
[POWERPC] iSeries: Fix section mismatch warning in lpevents
[POWERPC] iSeries: Fix section mismatch warnings
[POWERPC] iSeries: We need vio_enable_interrupts
[POWERPC] Fix RTC and device tree on linkstation machines
[POWERPC] Add of_register_i2c_devices()
[POWERPC] Fix loop with unsigned long counter variable
[POWERPC] Fix register labels on show_regs() message for 4xx/Book-E
[POWERPC] Only allow building of BootX text support on PPC_MULTIPLATFORM
[POWERPC] Fix the ability to reset on MPC8544 DS and MPC8568 MDS boards
[POWERPC] Fix mpc7448hpc2 tsi108 device_type bug
[POWREPC] Fixup a number of modpost warnings on ppc32
[POWERPC] Fix ethernet PHY support on MPC8544 DS
[POWERPC] Don't try to allocate resources for a Freescale POWERPC PHB
Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"
...
This reverts most of commit 19d36ccdc3.
The way to DEBUG_RODATA interactions with KPROBES and CPU hotplug is to
just not mark the text as being write-protected in the first place.
Both of those facilities depend on rewriting instructions.
Having "helpful" debug facilities that just cause more problem is not
being helpful. It just adds complexity and bugs. Not worth it.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change INT0 trigger mode from edge-sense mode to level-sense mode,
in order to fix the following timeout error:
'NETDEV WATCHDOG: eth0: transmit timed out'.
This patch is required only for the Mappi platform.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following two section mismatch warnings:
WARNING: vmlinux.o(.text+0x1ce84): Section mismatch: reference to .init.text:free_bootmem (between 'free_tce_table' and 'build_tce_table')
WARNING: vmlinux.o(.text+0x1d04d): Section mismatch: reference to .init.text:__alloc_bootmem_low (between 'alloc_tce_table' and 'kretprobe_trampoline_holder')
In both cases the functions was used only from __init
context so mark them __init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function arch_vma_name() is declared weak and thus it was
not noticed that x86_64 had two almost identical implementations.
It was introduced in syscall32.c by: c633090e31
It was introduced in mm/init.c by: 2aae950b21
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following compile error introduced by
commit e8666b2718 and reported
by Alexey Dobriyan:
<-- snip -->
CC arch/i386/kernel/acpi/cstate.o
In file included from arch/i386/kernel/acpi/cstate.c:17:
include/acpi/processor.h:88: error: expected specifier-qualifier-list before 'acpi_integer'
<-- snip -->
If you select something you must ensure that the dependencies of what
you are selecting are fulfilled.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Joshua Hoblitt <jhoblitt@ifa.hawaii.edu>
Cc: Dave Jones <davej@redhat.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
u32* volatile cyclone_timer means volatile auto pointer to u32,
which is clearly not what had been intended (we never even take
the address of that variable, let alone pass it to something that
could change it behind our back). u32 volatile * is what the
authors apparently wanted to say, but in reality we don't need that
qualifier there at all - it's (properly) only passed to iomem helpers
which takes care of that stuff just fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in 68328 timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in ColdFire PIT timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the unused mach_trap_init function pointer. All use of it
removed with change to using generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in ColdFire simple timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch to using the generic irq framework removed the
coldfire_trap_init() code, so remove all references to it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in 68360 timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not follow the frame pointers (/proc/X/task/1/stat) unless we were
compiled with them.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the shell call to explicitly use bash, since they are bash
specific and not all systems have bash as the default.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wire up ARCH_NO_VIRT_TO_BUS, and kill off the remaining users. The
dma-mapping code really wanted virt_to_phys()/phys_to_virt() anyways,
there are no inherently special bus addresses.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all CPUs support the DSP, and this leads to problems when mixing
and matching CPU types and DSP opcodes. Fix this up by only allowing
CONFIG_SH_DSP to be enabled for the CPUs that explicitly have such a
block.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently we calculate the first timeslice for every context
incorrectly - alloc_spu_context calls spu_set_timeslice before we set
ctx->prio so we always calculate the longest possible timeslice for the
lowest possible priority.
This patch makes sure to update the schedule-related fields before
calculating the timeslice and also makes sure we update the timeslice for
a non-running context when entering spu_run so a priority change affects
the context as soon as possible.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently initialize cbe_spu_info[].spus in both init_spu_base and
spu_sched_init. The initialise in spu_sched_init clears the SPU list,
so we end up with no physical SPUs. Because of this, the spu_run
syscall will block forever.
This change removes the unnecessary initialization in spu_sched_init.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Maple platform has ISA IOs but didn't call the new functions to
actually map those, thus crashing when trying to access the nvram.
This fixes Maple and JS2x using SLOF.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch uses the newly added functions for testing if an address is
an ISA or PCI IO port to properly unmap things in pci_iounmap that
aren't such ports. Without that, drivers using the iomap API will never
actually unmap resources, which on IBM server machines will prevent
hot-unplug of the corresponding HW adapters.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a function that tells you if a given kernel virtual address
is hitting a PCI or ISA IO port permanent mapping or not. This is to
be used in the next patch to fix iomap APIs to properly unmap things.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As of 2.6.22 the kernel doesn't recognize the i8042 keyboard/mouse
controller on the PegasosPPC. This is because of a feature/bug in the
OF device tree: the "device_type" attribute is an empty string instead
of "8042" as the kernel expects. This adds a secondary detection
which looks for a device whose *name* is "8042" if there is no device
whose *type* is "8042".
Signed-off-by: Alan Curry <pacman@world.std.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x4f568): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.setup_hvlpevent_queue' and '.process_hvlpevents')
setup_hvlpevent_queue is only called from __init code so make it __init
as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x8124): Section mismatch: reference to .init.text:.iSeries_early_setup (between '.__start_initialization_iSeries' and '.__mmu_off')
WARNING: vmlinux.o(.text+0x8128): Section mismatch: reference to .init.text:.early_setup (between '.__start_initialization_iSeries' and '.__mmu_off')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the RTC on linkstation ppc machines again, and updates the
device tree: add rtc nodes on i2c, remove bogus 0-size cache-line
declarations, rename interrupt-controller nodes, remove erroneous
interrupt-parent line, accidentally introduced by a recent patch.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Scan the device tree for i2c devices, check their "compatible" property
against a hard-coded table, and, if found, register with i2c boardinfo.
This provides the infrastructure needed to find i2c devices in the
device tree and register them with the i2c subsystem.
This and the following commit let the linkstation work with the new i2c
API and thus fix a regression.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a possible infinite loop when the unsigned long counter "i"
is used in lmb_add_region() in the following for loop:
for (i = rgn->cnt-1; i >= 0; i--)
by making the loop counter "i" be signed.
Signed-off-by: Manish Ahuja <ahuja@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In a show_regs() message The DEAR and ESR were reported as
DAR and DSISR which only exist on classic parts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
BootX text code is only supported on systems with real OF at this point
which is PPC_OF && PPC_MULTIPLATFORM.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add global-utilities node with has-rstcr on MPC8544 DS and MPC8568 MDS
boards so they are able to reset properly.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix mpc7448hpc2 tsi108 device_type bug.
Wrong device type will break the board startup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixed the following warnings:
WARNING: vmlinux.o(.text+0x2934): Section mismatch: reference to .init.text:__alloc_bootmem (between 'irq_alloc_host' and 'irq_set_default_host')
WARNING: vmlinux.o(.text+0xb2aa): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xb2b2): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xe354): Section mismatch: reference to .init.text:__alloc_bootmem (between 'pcibios_alloc_controller' and 'pci_domain_nr')
WARNING: vmlinux.o(.text+0x12768): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x127a8): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x17566c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8544 dts needed to set the new phy-connection-type to rgmii-id
for the Vitesse PHY on the board to work properly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI PHBs actual report back values in the BAR registers
this causes issues in that we try to allocate resources for them
and will get error messages like the following on MPC8544 DS:
PCI: Failed to allocate mem resource #1:80000000@0 for 0000:00:00.0
To address this if we are class PCI_CLASS_PROCESSOR_POWERPC, a normal
header type, and the PHB we clear out all the resources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit fd6e9d3945.
Having #size-cells == 0 in a node indicates that things under the
node aren't directly accessible, and therefore we shouldn't try to
translate addresses for devices under the node into CPU physical
addresses.
Some drivers, such as the nvram driver for powermacs, rely on
of_address_to_resource failing if they are called for a node
representing a device whose resources aren't directly accessible
by the CPU. These drivers were broken by commit fd6e9d39,
resulting in the "Lombard" powerbook hanging early in the boot
process.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Nail two more simple section mismatch errors
[IA64] fix section mismatch warnings
[IA64] rename partial_page
[IA64] Ensure that machvec is set up takes place before serial console
[IA64] vector-domain - fix vector_table
[IA64] vector-domain - handle assign_irq_vector(AUTO_ASSIGN)
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
pcibios_setup (between 'pci_setup' and 'quirk_mellanox_tavor')
setup_profiling_timer (between 'write_profile' and 'delayed_put_task_struct')
Signed-off-by: Tony Luck <tony.luck@intel.com>
In 741f98fe29 Sam added full
checking across the entire vmlinux image. This flushed out
a dozen new section mismatch warnings. Start the whack-a-mole
game again to stomp them out.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jens has added a partial_page thing in splice whcih conflicts with the ia64
one. Rename ia64 out of the way. (ia64 chose poorly).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make "struct ist_info" valid on both i386 and x86-64, and use the
structure by name in the setup code. Additionally, "Intel SpeedStep
IST" is redundant, refer to it as IST consistently.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For APM calls, BX contains the device index, which is zero for
the system BIOS. Disconnect requres BX = 0.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Starting with kernel 2.6.23-rc1, the i386 APM driver fails
on several of my machines with the message:
apm: BIOS not found
This happens because of a bug in the i386 boot code rewrite
from assembler to C. The original assembly code had the
following code in its APM BIOS presence test (boot/setup.S):
andw $0x02, %cx # Is 32 bit supported?
je done_apm_bios # No 32-bit, no (good) APM BIOS
That is, the code bails out if bit 2 is zero.
In the new C version, this is coded as (boot/apm.c):
if (cx & 0x02) /* 32 bits supported? */
return -1;
Here we see that the test has been accidentally inverted.
The fix is to negate the test. I've verified that this
allows the APM driver to work again on my affected machines.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Kconfig: remove CONFIG_ACPI_SLEEP from source
ACPI: quiet ACPI Exceptions due to no _PTC or _TSS
ACPI: Remove references to ACPI_STATE_S2 from acpi_pm_enter
ACPI: Kconfig: always enable CONFIG_ACPI_SLEEP on X86
ACPI: Kconfig: fold /proc/acpi/sleep under CONFIG_ACPI_PROCFS
ACPI: Kconfig: CONFIG_ACPI_PROCFS now defaults to N
ACPI: autoload modules - Create __mod_acpi_device_table symbol for all ACPI drivers
ACPI: autoload modules - Create ACPI alias interface
ACPI: autoload modules - ACPICA modifications
ACPI: asus-laptop: Fix failure exits
ACPI: fix oops due to typo in new throttling code
ACPI: ignore _PSx method for hotplugable PCI devices
ACPI: Use ACPI methods to select PCI device suspend state
ACPI, PNP: hook ACPI D-state to PNP suspend/resume
ACPI: Add acpi_pm_device_sleep_state helper routine
ACPI: Implement the set_target() callback from pm_ops
Parse the machvec command line option outside of the early_param()
so that ia64_mv is set before any console intialisation that
may result from early_param parsing.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This change fixes a panic when assign_irq_vector(irq) is called with
irq = AUTO_ASSIGN.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently most of the m68knommu cpu/board setup files are handling
the setup of fixed boot parameters (via CONFIG_BOOTPARAM) themselves.
Move all this into the common setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Intec Wildfire and WildFireMod boards.
Signed-Off-By: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is useless to preserve THREAD_SR in `resume'. The real user's sr
is actually in the stack. We also don't need to disable interrupts :
we'll never be in an invalid state, the sp switch is atomic.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add build support for the new Arcturus boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need to explicitly include linux/device.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Arcturus UC5272 and UC5282 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We didn't actually propogate the flag we pass into setup_indirect_pci()
to set indirect_type and thus were getting the wrong endianness if
PPC_INDIRECT_TYPE_BIG_ENDIAN was set.
Also, we need to or in additional flags rather than just doing a
direct assignment.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As it was a synonym for (CONFIG_ACPI && CONFIG_X86),
the ifdefs for it were more clutter than they were worth.
For ia64, just add a few stubs in anticipation of future
S3 or S4 support.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch removes old dead code:
- kill off sh73180 cpu support
- get rid of broken solution engine 73180 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The code in arch/sh/kernel/cpu/irq/pint.c doesn't compile, so let's
get rid of it to make space for a future pint implementation on top
of intc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The first 1MB of P3 space was reserved and used for page colouring,
as we've reworked that to use fixmaps, we can reclaim the space and
hand it back to VMALLOC_START.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We can't mark the whole thing init because there are dependencies
in bootloaders that assume that _start, or whatever the image
entry value, is 2 instructions before the "HdrS" signature.
In fact, TILO assumes this entry is always at 0x4000, yikes!
Also, right after the bootloader info area there are OBP strings and
values that get used later in the boot process, and those are not all
provably .init yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Sparc optimized memset (arch/sparc/lib/memset.S) does not fill last
byte of the memory area, if area size is less than 8 bytes and start
address is not word (4-bytes) aligned.
Here is code chunk where bug located:
/* %o0 - memory address, %o1 - size, %g3 - value */
8:
add %o0, 1, %o0
subcc %o1, 1, %o1
bne,a 8b
stb %g3, [%o0 - 1]
This code should write byte every loop iteration, but last time delay
instruction stb is not executed because branch instruction sets
"annul" bit.
Patch replaces bne,a by bne instruction.
Error can be reproduced by simple kernel module:
--------------------
#include <linux/module.h>
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <string.h>
static void do_memset(void **p, int size)
{
memset(p, 0x00, size);
}
static int __init memset_test_init(void)
{
char fooc[8];
int *fooi;
memset(fooc, 0xba, sizeof(fooc));
do_memset((void**)(fooc + 3), 1);
fooi = (int*) fooc;
printk("%08X %08X\n", fooi[0], fooi[1]);
return -1;
}
static void __exit memset_test_cleanup(void)
{
return;
}
module_init(memset_test_init);
module_exit(memset_test_cleanup);
MODULE_LICENSE("GPL");
EXPORT_NO_SYMBOLS;
--------------------
Signed-off-by: Alexander Shmelev <ashmelev@task.sun.mcst.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes boot failures when the build-id LD option is
actually used, because without it we end up with multiple
PT_LOAD sections which the SILO boot loader cannot handle.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'request-queue-t' of git://git.kernel.dk/linux-2.6-block:
[BLOCK] Add request_queue_t and mark it deprecated
[BLOCK] Get rid of request_queue_t typedef
spufs.h now has two enums for the sched_flags leading to identical
values for SPU_SCHED_WAS_ACTIVE and SPU_SCHED_NOTIFY_ACTIVE. Merge
them into a single enum as they were in the IBM development tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2.6.23-rc1 turned up another batch of references from non-__init code to
__init code. In most cases, these were missing __init annotations. In one
case (os_drop_memory), the annotation was present but wrong.
init_maps is __init, but for some reason was being very careful about the
mechanism by which it allocated memory, checking whether it was OK to use
kmalloc (at this point in the boot, it definitely isn't) and using either
alloc_bootmem_low_pages or kmalloc/vmalloc. So, the kmalloc/vmalloc code is
removed.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restructure do_aio thanks to commments from Ulrich and Al.
Uli started this by seeing that UML's initialization of a struct iocb
initialized fields that it shouldn't.
Al followed up by adding the following cleanups:
eliminating a variable by just using an anonymous structure in
its place.
hoisting a duplicated line out of the switch.
simplifying the error checking at the end.
I added a severity to the printk.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In 2.6.23-rc1, i386 fiddled its string support such that UML started getting
undefined references from modules. The UML asm/string.h was including the
i386 string.h, which defined __HAVE_ARCH_STR*, but the corresponding
implementations weren't being pulled in.
This is fixed by adding arch/i386/lib/string.h to the list of host
architecture files to be pulled in to UML.
A complication is that the libc exports file assumed that the generic strlen
and strstr weren't in use (i.e. __HAVE_ARCH_STR is defined), then they aren't
exported. This is untrue for strlen, which is exported in either case, so
this logic is not needed.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver previously registered its platform device data in its own
init function--that's bogus. Move that code to platform-specific
code in arch/ppc. This is being done so that the platform code can
decide at runtime whether to initialize this driver or not.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added the MPC85xx PCI device IDs that we need for the quirks we have.
Also, fixed the MPC8567E, MPC8567 device IDs which had the wrong value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add 8641/8641D device IDs as well.
All of which already exist or have been submitted to
The Linux PCI ID Repository at:
http://pci-ids.ucw.cz/
CC-to: pci-ids@ucw.cz
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added the P2P bridge present on the Arcadia base board and moved the VIA
Southbridge behind the bridge to reflect its actual position in the bus
organization. Added the RTC that's in the VIA Southbridge and expanded
the ranges array for the SOC node to allow proper address translation of
the RTC registers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setting the host bridge @8000 as primary. Also fixing a bug in
setting the USB interrupt numbers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
__INIT directive just before kernel_entry was ignored for most platforms.
This patch fixes it and get rid of this warning:
WARNING: vmlinux.o(.text+0x478): Section mismatch: reference to .init.text:start_kernel (between '_stext' and 'run_init_process')
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can make resources for platform_device_register_simple() "static
__initdata".
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replaces the deprecated __attribute_used__ with __used. Also makes some
style adjustments to abide by the kernel coding conventions.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
> WARNING: vmlinux.o(.text+0xbf20): Section mismatch: reference to
> .init.text:prom_free_prom_memory (between 'free_initmem' and 'copy_from_user_page')
prom_free_prom_memory() is called _before_ freeing init sections, so
it is false positive. __init_refok can be used for such cases.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
make ARCH_PXA select GENERIC_CLOCKEVENTS to fix the
building issue due to merge of clockevents based PXA
timer
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The current SH DMA API is somewhat broken, not correctly matching
virtual channel to the correct SH DMAC. This wasn't noticeable when
using g2 DMA for the sound driver - one channel 0 is as good as any
other! - but caused the pvr2 driver to fail.
This patch fixes the pvr2 problem and consequently fixes the sound
driver to ensure it continues to function.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This wires up kmap_coherent() and kunmap_coherent() on SH-4, and
moves away from the p3map_mutex and reserved P3 space, opting to
use fixmaps for colouring instead.
The copy_user_page()/clear_user_page() implementations are moved
to this, which fixes the nasty blowups with spinlock debugging
as a result of having some of these calls nested under the page
table lock.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some set of 85xx platforms have PCI-X controllers. The old arch/ppc
code setup these controllers and we haven't moved it over to arch/powerpc.
We use the PCI-X Capabilties to know if we are in PCI-X mode instead
of the Global Utilities PORDEVSR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the Freescale PCIe PHBs Not all firmwares setup the virtual P2P
bridge registers properly. Make sure they get setup based on what
the struct pci_controller got from the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need the ability to set P2P bridge registers to properly setup the virtual
P2P bridges that exist in PCIe controllers for some of the embedded setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't use setup_indirect_pci_nomap in arch/powerpc and it appears
the users that needed it from arch/ppc are now using setup_indirect_pci.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device. Add a quirk to just ignore the
FPGA.
This is based on the following patch from Andy & York:
http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the 83xx & 85xx device tree PCI related compartible property.
Used the following compatible properties:
PCI "fsl,mpc8349-pci"
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 8548 CDS PCI express controller node and PCI-X device node. The current
dts file is suitable for 8548 Rev 2.0 board with Arcadia 3.1.
This kind of board combination is the most popular.
Used the following compatible properties:
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the PCI capabilities to determine if we are PCIe PHB. Also use
PPC_INDIRECT_TYPE_NO_PCIE_LINK since the Freescale PCIe controllers
will lock the system if they don't have link and you try to do a config
access to anything but the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added PPC_INDIRECT_TYPE_NO_PCIE_LINK flag to the indirect pci handling
code to ensure that we don't talk to any device other than the PHB
if we don't have PCIe link. Some controllers will lockup if they try
to do a config cycle to any device on the bus except the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added early_find_capability that wraps pci_bus_find_capability and uses
fake_pci_bus() to allow us to call it before we've fully setup the
pci_controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This avoids a conflict with sparse builds.
Reported by Alexey Dobriyan, fix suggested by Al Viro
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the last inlined instances are gone, all that is left to do
is turning disable_irq_nosync on arm26 and m68k from defines to aliases
and we are all set - we can make these externs in linux/interrupt.h
uncoditional and kill remaining instances in asm/irq.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Convert from struct class_device to struct device
leds: leds-gpio for ngw100
leds: Add warning printks in error paths
leds: Fix trigger unregister_simple if register_simple fails
leds: Use menuconfig objects II - LED
leds: Teach leds-gpio to handle timer-unsafe GPIOs
leds: Add generic GPIO LED driver
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (77 commits)
ACPI: Populate /sys/firmware/acpi/tables/
ACPI: create CONFIG_ACPI_DEBUG_FUNC_TRACE
ACPI: update ACPI proc I/F removal schedule
ACPI: update feature-removal-schedule.txt, /sys/firmware/acpi/namespace is gone
ACPI: export ACPI events via acpi_mc_group multicast group
ACPI: fix empty macros found by -Wextra
ACPI: drivers/acpi/pci_link.c: lower printk severity
sony-laptop: Fix event reading in sony-laptop
sony-laptop: Add Vaio FE to the special init sequence
sony-laptop: Make the driver use MSC_SCAN and a setkeycode and getkeycode key table.
sony-laptop: Invoke _INI for SNC devices that provide it
sony-laptop: Add support for recent Vaios Fn keys (C series for now)
sony-laptop: map wireless switch events to KEY_WLAN
sony-laptop: add new SNC handlers
ACPI: thinkpad-acpi: add locking to brightness subdriver
ACPI: thinkpad-acpi: bump up version to 0.15
ACPI: thinkpad-acpi: make EC-based thermal readings non-experimental
ACPI: thinkpad-acpi: make sure DSDT TMPx readings don't return +128
ACPI: thinkpad-acpi: react to Lenovo ThinkPad differences in hot key
ACPI: thinkpad-acpi: allow use of CMOS NVRAM for brightness control
...
Get rid of warnings like
WARNING: vmlinux.o(.bootstrap.text+0x1a8): Section mismatch: reference to .init.text:x86_64_start_kernel (between 'initial_code' and 'init_rsp')
- Move initialization code into .text.head like i386 because modpost knows about this already
- Mark initial_code .initdata
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: vmlinux.o(.text+0x188ea): Section mismatch: reference to .init.text:__alloc_bootmem_core (between 'alloc_bootmem_high_node' and 'get_gate_vma')
alloc_bootmem_high_node() is only used from __init scope so declare it __init.
And in addition declare the weak variant __init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: vmlinux.o(.text+0x945e): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
WARNING: vmlinux.o(.text+0x9474): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
hpet_arch_init is only used from __init context so mark it __init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The performance counters on K7 are only 48 bits wide, so using bit 63 to
check if the counter overflowed is wrong. Let's use bit 47 instead.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got an oops while booting a 32bit kernel on KVM because it doesn't
implement performance counters used by the NMI watchdog. Handle this
case.
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to index register access ordering problems, when using macros a line
like this fails (and does nothing):
setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
With inlined functions this line will work as expected.
Note about a side effect: Seems on Geode GX1 based systems the
"suspend on halt power saving feature" was never enabled due to this
wrong macro expansion. With inlined functions it will be enabled, but
this will stop the TSC when the CPU runs into a HLT instruction.
Kernel output something like this:
Clocksource tsc unstable (delta = -472746897 ns)
This is the 3rd version of this patch.
- Adding missed arch/i386/kernel/cpu/mtrr/state.c
Thanks to Andres Salomon
- Adding some big fat comments into the new header file
Suggested by Andi Kleen
AK: fixed x86-64 compilation
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kstat_irqs(0) includes the count of interrupt 0 from all cpus, not just
the current cpu. The updated interrupt 0 on other cpus can stop the
nmi_watchdog from tripping, so only include the current cpu's int 0.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mainly changes the nops for alternative, so not very revolutionary.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously this flag was only used on 32bit, but some shared code can use
it now.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a machine check or NMI occurs while multiple byte code is patched
the CPU could theoretically see an inconsistent instruction and crash.
Prevent this by temporarily disabling MCEs and returning early in the
NMI handler.
Based on discussion with Mathieu Desnoyers.
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reenable kprobes and alternative patching when the kernel text is write
protected by DEBUG_RODATA
Add a general utility function to change write protected text. The new
function remaps the code using vmap to write it and takes care of CPU
synchronization. It also does CLFLUSH to make icache recovery faster.
There are some limitations on when the function can be used, see the
comment.
This is a newer version that also changes the paravirt_ops code.
text_poke also supports multi byte patching now.
Contains bug fixes from Zach Amsden and suggestions from Mathieu
Desnoyers.
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Zach Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch uses the read and write functions provided at system.h
for control registers instead of writting raw assembly over and
over again in .c files. Functions to manipulate cr2 and cr8 were
provided, as they were lacking.
Also, removed some extra space after closing brackets
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the i386 behave the same way that x86_64 does when a
segfault happens. A line gets printed to the kernel log so that tools
that need to check for failures can behave more uniformly between
debug.show_unhandled_signals sysctl variable to 0 (or by doing echo 0 >
/proc/sys/debug/exception-trace)
Also, all of the lines being printed are now using printk_ratelimit() to
deny the ability of DoS from a local user with a program like the
following:
main()
{
while (1)
if (!fork()) *(int *)0 = 0;
}
This new revision also includes the fix that Andrew did which got rid of
new sysctl that was added to the system in earlier versions of this.
Also, 'show-unhandled-signals' sysctl has been renamed back to the old
'exception-trace' to avoid breakage of people's scripts.
AK: Enabling by default for i386 will be likely controversal, but let's see what happens
AK: Really folks, before complaining just fix your segfaults
AK: I bet this will find a lot of silent issues
Signed-off-by: Masoud Sharbiani <masouds@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
[ Personally, I've found the complaints useful on x86-64, so I'm all for
this. That said, I wonder if we could do it more prettily.. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a mismerge in commit 8b6f50ef1d:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move register and other definitions out of the
include/asm-arm/arch-s3c2410 into the the arch
directories of include/asm-arm/plat-s3c24xx and
include/asm-arm/plat-s3c.
This move is in preperation of the merging of
s3c2400 and s3c6400.
The following git mv commands are needed before
this patch can be applied:
git mv include/asm-arm/arch-s3c2410/regs-ac97.h include/asm-arm/plat-s3c/regs-ac97.h
git mv include/asm-arm/arch-s3c2410/regs-adc.h include/asm-arm/plat-s3c/regs-adc.h
git mv include/asm-arm/arch-s3c2410/regs-iis.h include/asm-arm/plat-s3c24xx/regs-iis.h
git mv include/asm-arm/arch-s3c2410/regs-spi.h include/asm-arm/plat-s3c24xx/regs-spi.h
git mv include/asm-arm/arch-s3c2410/regs-udc.h include/asm-arm/plat-s3c24xx/regs-udc.h
git mv include/asm-arm/arch-s3c2410/udc.h include/asm-arm/plat-s3c24xx/udc.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the static maps for the LCD and USB devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename the S3C24XX configuration options for the watchdog
boot controls for moving to the arch/arm/plat-s3c moves.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename DEBUG_S3C2410_PORT to DEBUG_S3C_PORT as well as
DEBUG_S3C2410_UART to DEBUG_S3C_UART as part of the updates
to moving to plat-s3c for S3C base support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_S3C2410_LOWLEVEL_UART_PORT to be
CONFIG_S3C_LOWLEVEL_UART_PORT as we move to using
plat-s3c for base of S3C operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the Kconfig to create configuration options based on which
CPUs are supported for the low level serial code. This means that
the debug macros can be optimised for the type(s) of CPU that are
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create the initial arch/arm/plat-s3c directory and start
linking it into the arch/arm build heirarchy ready to
receive the generic parts of the S3C24XX support to be
used when adding S3C6400 devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves items of the s3c24xx support into
a new plat-s3c directory for items that use the
s3c24xx support but are not directly s3c24xx
compatible, such as the s3c2400 and s3c6400.
git mv commands:
git mv include/asm-arm/arch-s3c2410/iic.h include/asm-arm/plat-s3c/iic.h
git mv include/asm-arm/arch-s3c2410/nand.h include/asm-arm/plat-s3c/nand.h
git mv include/asm-arm/arch-s3c2410/regs-iic.h include/asm-arm/plat-s3c/regs-iic.h
git mv include/asm-arm/arch-s3c2410/regs-nand.h include/asm-arm/plat-s3c/regs-nand.h
git mv include/asm-arm/arch-s3c2410/regs-rtc.h include/asm-arm/plat-s3c/regs-rtc.h
git mv include/asm-arm/arch-s3c2410/regs-serial.h include/asm-arm/plat-s3c/regs-serial.h
git mv include/asm-arm/arch-s3c2410/regs-timer.h include/asm-arm/plat-s3c/regs-timer.h
git mv include/asm-arm/arch-s3c2410/regs-watchdog.h include/asm-arm/plat-s3c/regs-watchdog.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reimplements arch/arm/mach-pxa/time.c using a clock_event_device based
on OSMR0. Tested on PXA270, linux-2.6.22+arm:pxa patches.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0x1cefcc): Section mismatch: reference to .init.text:.pcibios_setup (between '.pci_setup' and '.pci_init')
pci_setup() is marked __devinit and calls pcibios_setup.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some HW platforms, such as the new cell blades, requires some MPIC sources
to be left alone by the operating system. This implements support for
a "protected-sources" property in the mpic controller node containing a list
of source numbers to be protected against operating system interference.
For those interested in the gory details, the MPIC on the southbridge of
those blades has some of the processor outputs routed to the cell, and
at least one routed as a GPIO to the service processor. It will be used
in the GA product for routing some of the southbridge error interrupts
to the service processor which implements some of the RAS stuff, such
as checkstopping when fatal errors occurs before they can propagate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
...since it modifies it (when it sets the OF_DETACHED flag).
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes the requirement for callers to get_cpu() to check in simple
cases. i386 and x86_64 already received a similar treatment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Classic 32-bit PowerPC CPUs, and the early 64-bit PowerPC CPUs, don't
provide a way to prevent execution from readable pages, that is, the
MMU doesn't distinguish between data reads and instruction reads,
although a different exception is taken for faults in data accesses
and instruction accesses.
Commit 9ba4ace39f, in the course of
fixing another bug, added a check that meant that a page fault due
to an instruction access would fail if the vma did not have the
VM_EXEC flag set. This gives an inconsistent enforcement on these
CPUs of the no-execute status of the vma (since reading from the page
is sufficient to allow subsequent execution from it), and causes old
versions of ppc32 glibc (2.2 and earlier) to fail, since they rely
on executing the word before the GOT but don't have it marked
executable.
This fixes the problem by allowing execution from readable (or writable)
areas on CPUs which do not provide separate control over data and
instruction reads.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In some configuration, xmon help string is larger than xmon_printf
buffer. We need not to use printf. This patch adds xmon_puts and
change to use it to show help string.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because xmon_write doesn't change the buffer, we should add 'const'
qualifier to the argument which points it.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The config symbol for SPE support is called CONFIG_SPU_BASE, not
CONFIG_SPE_BASE.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: ERROR: "sys_ioctl" [arch/sparc64/solaris/solaris.ko] undefined!
[SPARC32]: Make PAGE_SHARED a read-mostly variable.
[SPARC32]: Take enable_irq/disable_irq out of line.
[SPARC32]: clean include/asm-sparc/irq.h
[SPARC32]: Fix rounding errors in ndelay/udelay implementation.
From: Christoph Hellwig <hch@infradead.org>
On Fri, Jul 20, 2007 at 09:24:42AM -0400, Horst H. von Brand wrote:
> When building v2.6.22-3478-g275afca on sparc64 (.config attached) I get:
>
> MODPOST vmlinux
> Building modules, stage 2.
> MODPOST 463 modules
> ERROR: "sys_ioctl" [arch/sparc64/solaris/solaris.ko] undefined!
Sorry, my fault.
It looked to me like sparc64 exports sys_ioctl on it's own, but it
only exports compat_sys_ioctl on it's own.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move stuff used only by arch/sparc/kernel/* into arch/sparc/kernel/irq.h
and into individual files in there (e.g. macros internal to sun4m_irq.c,
etc.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ndelay and __udelay have not been delayung >= specified time.
The problem with __ndelay has been tacked down to the rounding of the
multiplier constant. By changing this, delays > app 18us are correctly
calculated.
The problem with __udelay has also been tracked down to rounding issues.
Changing the multiplier constant (to match that used in sparc64) corrects
for large delays and adding in a rounding constant corrects for trunctaion
errors in the claculations.
Many short delays will return without looping. This is not an error as there
is the fixed delay of doing all the maths to calculate the loop count.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces struct pci_sysdata to x86 and x86-64, and
converts the existing two users (NUMA, Calgary) to use it.
This lays the groundwork for having other users of sysdata, such as
the PCI domains work.
The Calgary bits are tested, the NUMA bits just look ok.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes k8topology multicore aware instead of limited to signle- and
dual-core CPUs. It uses the CPUID to be more future proof.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leftovers from the removal of the more general (but abandoned) SMP
alternatives.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dead or misnamed CONFIG_BALANCED_IRQ_DEBUG found by Robert P. J. Day.
It's not a Kconfig variable.
Since this debug code is ancient, I suggest to get rid of this
misleading CONFIG_ macro by deleting all of this debug code.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Robert P. J. Day" <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert HPET resources after pci probing has been completed in order to
avoid resource conflicts with PCI resource reservation. With this change
the HPET firmware resources will be identified, but it should also not
cause issues when the HPET address falls on a BAR in a PCI device, and the
PCI enumeration cannot reserve the resources.
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This builds upon the existing geode infrastructure, but adds southbridge
support, some GPIO functions, and a header file (asm-i386/geode.h) with some
useful GX/LX detection tests.
The majority of this code was written by Jordan Crouse.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users that use kernel log filtering (e.g. via syslogd or a proprietry method)
wouldn't like to see warning prints that are not really warnings.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_vm_area always returns an area with an adjacent guard page. That guard
page is included in vm_struct.size. iounmap uses vm_struct.size to
determine how much address space needs to have change_page_attr applied to
it, which will BUG if applied to the guard page.
This patch adds a helper function - get_vm_area_size() in linux/vmalloc.h -
to return the actual size of a vm area, and uses it to make iounmap do the
right thing. There are probably other places which should be using
get_vm_area_size().
Thanks to Dave Young <hidave.darkstar@gmail.com> for debugging the
problem.
[ Andi, it wasn't clear to me whether x86_64 needs the same fix. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
setup_pit_timer is declared in asm-i386/timer.h. Move it to the pit header
file, so it can be used by x86_64 as well.
Move also the PIT constants.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I fixed this in x86_64. Looks like the kind of thing that will break voyager
on i386.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the volatile in apic. We have a cpu_relax() in the wait loop. Fix a
coding style issue while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When NUMA emulation succeeds, acpi_numa needs to be set to -1 so that
srat_disabled() will always return true. We won't be calling
acpi_scan_nodes() or registering the true nodes we've found.
[hugh@veritas.com: Fix x86_64 CONFIG_NUMA_EMU build: acpi_numa needs CONFIG_ACPI_NUMA]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
e820_hole_size() now uses the newly extracted helper function,
e820_find_active_region(), to determine the size of usable RAM in a range of
PFN's.
This was previously broken because of two reasons:
- The start and end PFN's of each e820 entry were not properly rounded
prior to excluding those entries in the range, and
- Entries smaller than a page were not properly excluded from being
accumulated.
This resulted in emulated nodes being incorrectly mapped to ranges that
were completely reserved and not candidates for being registered as
active ranges.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For K8 system: 4G RAM with memory hole remapping enabled, or more than 4G
RAM installed. when using kexec to load second kernel. In the second
kernel, when mem is allocated for GART, it will do the memset for clear, it
will cause restart, because some device still used that for dma. solution
will be:
in second kernel: disable that at first before we try to allocate mem for
it. or in the first kernel: do disable that before shutdown.
Andi/Eric/Alan prefer to second one for clean shutdown in first kernel.
Andi also point out need to consider to AGP enable but mem less 4G case
too.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function is called via dma_ops->.., so change it to static
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the pcspkr private PIT lock by the global PIT lock to serialize the
PIT access all over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During a VM oom condition, kill all threads in the process group.
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory condition.
Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or otherwise handled, and makes it very obvious that
something has gone wrong.
This change allows the entire process group to be taken down, rather than just
the one thread.
Signed-off-by: Will <will_schmidt@vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some interrupt entry points are currently defined in i8259.c They probably
belong in a header. Right now, their only user is init_IRQ, justifying
their declaration in-file. But when virtualization comes in, we may be
interested in using that functions in late initializations.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are seeing corruption of the decompressed kernel. It is suspected that
this is platform specific as it has yet to be seen on any other x86. Move
the kernel to the 16MB boundary.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unneeded test of task != NULL from
arch/i386/kernel/traps.c::dump_trace()
At the start of the function we have this test:
if (!task)
task = current;
so further down there's no need to test 'task'.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAE is useful for more than supporting more than 4GB RAM. It supports
expanded swapspace and NX executable protections. Some users may want NX
or expanded swapspace support without the overhead or instability of
highmem. For these reasons, the following patch divorces CONFIG_X86_PAE
from CONFIG_HIGHMEM64G.
Cc: Mark Lord <lkml@rtr.ca>
Signed-off-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some systems have a HPET which is not incrementing, which leads to a
complete hang. Detect it during HPET setup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch enables reboot through BIOS on the Dell Optiplex 745
Small Form Factor base, on which reboot hangs. The larger form factor does
not require this, hence the match on DMI_BOARD_NAME.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some systems the ACPI NVS area is located in the first 1 MB of RAM and
it is overwritten by the i386 code during the restore after hibernation.
This confuses the ACPI platform firmware that doesn't update the AC adapter
status appropriately as a result
(http://bugzilla.kernel.org/show_bug.cgi?id=7995).
The solution is to register the reserved memory in the first 1 MB as
'nosave', so that swsusp doesn't touch it during the restore. Also, this
has been done on x86_64 for a long time now, so this patch makes the i386
restore code behave like the x86_64 one.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: arch/i386/kernel/built-in.o(.init.text+0x3818): Section mismatch: reference to .exit.text:cache_remove_dev (between 'cacheinfo_cpu_callback' and 'cache_sysfs_init')
It points out that a function marked __cpuexit is calling a function marked
__cpuinit => oops.
The call happens only in an error-condition which may explain why we have
not seen it before.
The offending function was not used anywhere else - so marked it __cpuexit.
Note: This warning triggers only with a local copy of modpost
but that version will soon be pushed out.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pgd_{c,d}tor() can now become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the bitmap changes we can get rid of the unlocked versions of
calgary_unmap_sg and iommu_free. Fold __calgary_unmap_sg and
__iommu_free into their calgary_unmap_sg and iommu_free, respectively.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
there function are called via dma_ops->.., so change them to static
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the IOMMU table's lock protects both the bitmap and access
to the hardware's TCE table. Access to the TCE table is synchronized
through the bitmap; therefore, only hold the lock while modifying the
bitmap. This gives a yummy 10-15% reduction in CPU utilization for
netperf on a large SMP machine.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No actual code was harmed in the production of this patch.
Thanks to Andrew Morton <akpm@linux-foundation.org> for telling me
about checkpatch.pl.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup unneeded macros used for register space address calculation.
Now we are using the EBDA to find the space address.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@bull.net>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This works around a bug where DMAs that have the same addresses as
some MEM regions do not go through. Not clear yet if this is due to a
mis-configuration or something deeper.
[akpm@linux-foundation.org: coding style fixlet]
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide seperate versions for Calgary and CalIOC2
Also print out the PCIe Root Complex Status on CalIOC2 errors
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CalIOC2 is a PCI-e implementation of the Calgary logic. Most of the
programming details are the same, but some differ, e.g., TCE cache
flush. This patch introduces CalIOC2 support - detection and various
support routines. It's not expected to work yet (but will with
follow-on patches).
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... in preparation for doing it differently for CalIOC2.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calgary and CalIOC2 share most of the same logic. Introduce struct
cal_chipset_ops for quirks and tce flush logic which are
[akpm@linux-foundation.org: make calgary_chip_ops static]
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... will be used by CalIOC2 later
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Rise CPUs were only very short-lived, and there are no reports of
anyone both owning one and running Linux on it.
Googling for the printk string "CPU: Rise iDragon" didn't find any dmesg
available online.
If it turns out that against all expectations there are actually users
reverting this patch would be easy.
This patch will make the kernel images smaller by a few bytes for all
i386 users.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86_64 kernel, level triggered irq migration gets initiated in the
context of that interrupt(after executing the irq handler) and following
steps are followed to do the irq migration.
1. mask IOAPIC RTE entry; // write to IOAPIC RTE
2. EOI; // processor EOI write
3. reprogram IOAPIC RTE entry // write to IOAPIC RTE with new destination and
// and interrupt vector due to per cpu vector
// allocation.
4. unmask IOAPIC RTE entry; // write to IOAPIC RTE
Because of the per cpu vector allocation in x86_64 kernels, when the irq
migrates to a different cpu, new vector(corresponding to the new cpu) will
get allocated.
An EOI write to local APIC has a side effect of generating an EOI write for
level trigger interrupts (normally this is a broadcast to all IOAPICs).
The EOI broadcast generated as a side effect of EOI write to processor may
be delayed while the other IOAPIC writes (step 3 and 4) can go through.
Normally, the EOI generated by local APIC for level trigger interrupt
contains vector number. The IOAPIC will take this vector number and search
the IOAPIC RTE entries for an entry with matching vector number and clear
the remote IRR bit (indicate EOI). However, if the vector number is
changed (as in step 3) the IOAPIC will not find the RTE entry when the EOI
is received later. This will cause the remote IRR to get stuck causing the
interrupt hang (no more interrupt from this RTE).
Current x86_64 kernel assumes that remote IRR bit is cleared by the time
IOAPIC RTE is reprogrammed. Fix this assumption by checking for remote IRR
bit and if it still set, delay the irq migration to the next interrupt
arrival event(hopefully, next time remote IRR bit will get cleared before
the IOAPIC RTE is reprogrammed).
Initial analysis and patch from Nanhai.
Clean up patch from Suresh.
Rewritten to be less intrusive, and to contain a big fat comment by Eric.
[akpm@linux-foundation.org: fix comments]
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nanhai Zou <nanhai.zou@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Keith Packard <keith.packard@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This helps to reduce the frequency at which the CPU must be taken out of a
lower-power state.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Tim Hockin <thockin@hockin.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as921) adds code to the show_regs() routine in i386 and x86_64
to print the contents of the debug registers along with all the others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following section mismatch warnings were reported by Andrey Borzenkov:
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text:amd_init_mtrr from .text between 'mtrr_bp_init' (at offset 0x967a) and 'mtrr_attrib_to_str'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text:cyrix_init_mtrr from .text between 'mtrr_bp_init' (at offset 0x967f) and 'mtrr_attrib_to_str'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text:centaur_init_mtrr from .text between 'mtrr_bp_init' (at offset 0x9684) and 'mtrr_attrib_to_str'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text: from .text between 'get_mtrr_state' (at offset 0xa735) and 'generic_get_mtrr'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text: from .text between 'get_mtrr_state' (at offset 0xa749) and 'generic_get_mtrr'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text: from .text between 'get_mtrr_state' (at offset 0xa770) and 'generic_get_mtrr'
It was tracked down to a few functions missing __init tag.
Compile tested only.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
The MCE handler has several paths that it can take, depending on various
conditions of the MCE status and the value of the 'tolerant' knob. The
exact semantics are not well defined and the code is a bit twisty.
Description:
This patch makes the MCE handler's behavior more clear by documenting the
behavior for various 'tolerant' levels. It also fixes or enhances
several small things in the handler. Specifically:
* If RIPV is set it is not safe to restart, so set the 'no way out'
flag rather than the 'kill it' flag.
* Don't panic() on correctable MCEs.
* If the _OVER bit is set *and* the _UC bit is set (meaning possibly
dropped uncorrected errors), set the 'no way out' flag.
* Use EIPV for testing whether an app can be killed (SIGBUS) rather
than RIPV. According to docs, EIPV indicates that the error is
related to the IP, while RIPV simply means the IP is valid to
restart from.
* Don't clear the MCi_STATUS registers until after the panic() path.
This leaves the status bits set after the panic() so clever BIOSes
can find them (and dumb BIOSes can do nothing).
This patch also calls nonseekable_open() in mce_open (as suggested by akpm).
Result:
Tolerant levels behave almost identically to how they always have, but
not it's well defined. There's a slightly higher chance of panic()ing
when multiple errors happen (a good thing, IMHO). If you take an MBE and
panic(), the error status bits are not cleared.
Alternatives:
None.
Testing:
I used software to inject correctable and uncorrectable errors. With
tolerant = 3, the system usually survives. With tolerant = 2, the system
usually panic()s (PCC) but not always. With tolerant = 1, the system
always panic()s. When the system panic()s, the BIOS is able to detect
that the cause of death was an MC4. I was not able to reproduce the
case of a non-PCC error in userspace, with EIPV, with (tolerant < 3).
That will be rare at best.
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
/dev/mcelog is typically polled manually. This is less than optimal for
situations where accurate accounting of MCEs is important. Calling
poll() on /dev/mcelog does not work.
Description:
This patch adds support for poll() to /dev/mcelog. This results in
immediate wakeup of user apps whenever the poller finds MCEs. Because
the exception handler can not take any locks, it can not call the wakeup
itself. Instead, it uses a thread_info flag (TIF_MCE_NOTIFY) which is
caught at the next return from interrupt or exit from idle, calling the
mce_user_notify() routine. This patch also disables the "fake panic"
path of the mce_panic(), because it results in printk()s in the exception
handler and crashy systems.
This patch also does some small cleanup for essentially unused variables,
and moves the user notification into the body of the poller, so it is
only called once per poll, rather than once per CPU.
Result:
Applications can now poll() on /dev/mcelog. When an error is logged
(whether through the poller or through an exception) the applications are
woken up promptly. This should not affect any previous behaviors. If no
MCEs are being logged, there is no overhead.
Alternatives:
I considered simply supporting poll() through the poller and not using
TIF_MCE_NOTIFY at all. However, the time between an uncorrectable error
happening and the user application being notified is *the*most* critical
window for us. Many uncorrectable errors can be logged to the network if
given a chance.
I also considered doing the MCE poll directly from the idle notifier, but
decided that was overkill.
Testing:
I used an error-injecting DIMM to create lots of correctable DRAM errors
and verified that my user app is woken up in sync with the polling interval.
I also used the northbridge to inject uncorrectable ECC errors, and
verified (printk() to the rescue) that the notify routine is called and the
user app does wake up. I built with PREEMPT on and off, and verified
that my machine survives MCEs.
[wli@holomorphy.com: build fix]
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: William Irwin <bill.irwin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
/dev/mcelog is a clear-on-read interface. It is currently possible for
multiple users to open and read() the device. Users are protected from
each other during any one read, but not across reads.
Description:
This patch adds support for O_EXCL to /dev/mcelog. If a user opens the
device with O_EXCL, no other user may open the device (EBUSY). Likewise,
any user that tries to open the device with O_EXCL while another user has
the device will fail (EBUSY).
Result:
Applications can get exclusive access to /dev/mcelog. Applications that
do not care will be unchanged.
Alternatives:
A simpler choice would be to only allow one open() at all, regardless of
O_EXCL.
Testing:
I wrote an application that opens /dev/mcelog with O_EXCL and observed
that any other app that tried to open /dev/mcelog would fail until the
exclusive app had closed the device.
Caveats:
None.
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert the unclaimed MMCONFIG resources into the resource tree without the
IORESOURCE_BUSY flag during late initialization. This allows the MMCONFIG
regions to be visible in the iomem resource tree without interfering with
other system resources that were discovered during PCI initialization.
[akpm@linux-foundation.org: nanofixes]
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we are in the emulated NUMA case, we need to make sure that all existing
apicid_to_node mappings that point to real node ID's now point to the
equivalent fake node ID's.
If we simply iterate over all apicid_to_node[] members for each node, we risk
remapping an entry if it shares a node ID with a real node. Since apicid's
may not be consecutive, we're forced to create an automatic array of
apicid_to_node mappings and then copy it over once we have finished remapping
fake to real nodes.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For NUMA emulation, our SLIT should represent the true NUMA topology of the
system but our proximity domain to node ID mapping needs to reflect the
emulated state.
When NUMA emulation has successfully setup fake nodes on the system, a new
function, acpi_fake_nodes() is called. This function determines the proximity
domain (_PXM) for each true node found on the system. It then finds which
emulated nodes have been allocated on this true node as determined by its
starting address. The node ID to PXM mapping is changed so that each fake
node ID points to the PXM of the true node that it is located on.
If the machine failed to register a SLIT, then we assume there is no special
requirement for emulated node affinity so we use the default LOCAL_DISTANCE,
which is newly exported to this code, as our measurement if the emulated nodes
appear in the same PXM. Otherwise, we use REMOTE_DISTANCE.
PXM_INVAL and NID_INVAL are also exported to the ACPI header file so that we
can compare node_to_pxm() results in generic code (in this case, the SRAT
code).
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The logic in e820_find_active_regions() for determining the true active
regions for an e820 entry given a range of PFN's is needed for
e820_hole_size() as well.
e820_hole_size() is called from the NUMA emulation code to determine the
reserved area within an address range on a per-node basis. Its logic should
duplicate that of finding active regions in an e820 entry because these are
the only true ranges we may register anyway.
[akpm@linux-foundation.org: cleanup]
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds caching of pgds and puds, pmds, pte. That way we can avoid costly
zeroing and initialization of special mappings in the pgd.
A second quicklist is useful to separate out PGD handling. We can carry the
initialized pgds over to the next process needing them.
Also clean up the pgd_list handling to use regular list macros. There is no
need anymore to avoid the lru field.
Move the add/removal of the pgds to the pgdlist into the constructor /
destructor. That way the implementation is congruent with i386.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every file should include the headers containing the prototypes for its
global functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Constrain __supported_pte_mask and NX handling to just the PAE kernel.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hence remove its handling in the opposite case.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.. and adjust documentation to properly reflect options that are
x86-64 specific.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Consolidate the three 32-bit system call entry points so that they all
treat registers in similar ways.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused code and variables and do some codingstyle / whitespace
cleanups while at it.
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xtime can be initialized including the cmos update from the generic
timekeeping code. Remove the arch specific implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the generic cmos update function in kernel/time/ntp.c
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current SMI detection logic in read_hpet_tsc() makes sure,
that when a SMI happens between the read of the HPET counter and
the read of the TSC, this wrong value is used for TSC calibration.
This is not the intention of the function. The comparison must ensure,
that we do _NOT_ use such a value.
Fix the check to use calibration values where delta of the two TSC reads
is smaller than a reasonable threshold.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Intel PerfMon NMI watchdog reserves the first performance counter,
but uses the second one. Make it correctly reserve the second one.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not fully softirq safe anyways.
Can't do a WARN_ON unfortunately because it could trigger in the
panic case.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With that an L3 cache is correctly reported in the cache information in /sys
With fixes from Andreas Herrmann and Dean Gaudet and Joachim Deguara
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements new vDSO for x86-64. The concept is similar
to the existing vDSOs on i386 and PPC. x86-64 has had static
vsyscalls before, but these are not flexible enough anymore.
A vDSO is a ELF shared library supplied by the kernel that is mapped into
user address space. The vDSO mapping is randomized for each process
for security reasons.
Doing this was needed for clock_gettime, because clock_gettime
always needs a syscall fallback and having one at a fixed
address would have made buffer overflow exploits too easy to write.
The vdso can be disabled with vdso=0
It currently includes a new gettimeofday implemention and optimized
clock_gettime(). The gettimeofday implementation is slightly faster
than the one in the old vsyscall. clock_gettime is significantly faster
than the syscall for CLOCK_MONOTONIC and CLOCK_REALTIME.
The new calls are generally faster than the old vsyscall.
Advantages over the old x86-64 vsyscalls:
- Extensible
- Randomized
- Cleaner
- Easier to virtualize (the old static address range previously causes
overhead e.g. for Xen because it has to create special page tables for it)
Weak points:
- glibc support still to be written
The VM interface is partly based on Ingo Molnar's i386 version.
Includes compile fix from Joachim Deguara
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler generally generates reasonable inline code for the simple
cases and for the rest it's better for code size for them to be out of line.
Also there they can be potentially optimized more in the future.
In fact they probably should be in a .S file because they're all pure
assembly, but that's for another day.
Also some code style cleanup on them while I was on it (this seems
to be the last untouched really early Linux code)
This saves ~12k text for a defconfig kernel with gcc 4.1.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In acpi_scan_nodes(), we immediately return -1 if acpi_numa <= 0, meaning
we haven't detected any underlying ACPI topology or we have explicitly
disabled its use from the command-line with numa=noacpi.
acpi_table_print_srat_entry() and acpi_table_parse_srat() are only
referenced within drivers/acpi/numa.c, so we can mark them as static and
remove their prototypes from the header file.
Likewise, pxm_to_node_map[] and node_to_pxm_map[] are only used within
drivers/acpi/numa.c, so we mark them as static and remove their externs
from the header file.
The automatic 'result' variable is unused in acpi_numa_init(), so it's
removed.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use LOCAL_DISTANCE and REMOTE_DISTANCE in x86_64 ACPI code
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux 64bit only uses the IO-APIC ID as an internal cookie. In the future
there could be some cases where the IO-APIC IDs are not unique because
they share an 8 bit space with CPUs and if there are enough CPUs
it is difficult to get them that. But Linux needs the io apic ID
internally for its data structures. Assign unique IO APIC ids on
table parsing.
TBD do for 32bit too
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug introduced with the CLFLUSH changes: we must always flush pages
changed in cpa(), not just when they are reverted.
Reenable CLFLUSH usage with that now (it was temporarily disabled
for .22)
Add some BUG_ONs
Contains fixes from Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reading from the signal{1,2} files requires a spu_acquire_saved, so make these
files write-only for contexts created with SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PS3 bootwrapper files use instructions only available on 64-bit CPUs.
Add the code generation directive '.machine "ppc64"' for toolchains
configured for 32-bit CPUs.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
