Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cpm_uart_init_portdesc is referenced from non-init code and thus we were
getting the following warning:
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:cpm_uart_init_portdesc from .text between 'cpm_uart_init' (at offset 0x18020) and 'cpm_uart_drv_remove'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The rheap allocation functions return a pointer, but the actual value is based
on how the heap was initialized, and so it can be anything, e.g. an offset
into a buffer. A ulong is a better representation of the value returned by
the allocation functions.
This patch changes all of the relevant rheap functions to use a unsigned long
integers instead of a pointer. In case of an error, the value returned is
a negative error code that has been cast to an unsigned long. The caller can
use the IS_ERR_VALUE() macro to check for this.
All code which calls the rheap functions is updated accordingly. Macros
IS_MURAM_ERR() and IS_DPERR(), have been deleted in favor of IS_ERR_VALUE().
Also added error checking to rh_attach_region().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch changes the interrupt enable sequence for the sunzilog driver
so that interrupts are not enabled untill after the interrupt handler has
been installed. If this is not done, some SS1 and SS2 sun4c systems panic
on un-handled interrupt before the handler gets installed preventing boot.
It also adds in support for the ESCC version of the zilog chips. The
changes mean that the FIFO will be enabled for ESCC versions of the
SCC UART. My interpretation of the SCC manual and the existing interrupt
handler code is that it sould be able to make good use of the FIFO without
issues.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make x86 COM ports into platform devices and don't probe for them
if we have PNP.
This prevents double discovery, where a device was found both by
the legacy probe and by 8250_pnp, e.g.,
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
This also means IRDA devices without a UART PNP ID will no longer be
claimed by the serial driver, which might require changes in IRDA
drivers and administration.
In addition to this patch, you may need to configure a setserial init
script, e.g., /etc/init.d/setserial, so it doesn't poke legacy UART
stuff back in. On Debian, "dpkg-reconfigure setserial" with the "kernel"
option does this.
To force the old legacy probe behavior even when we have PNPBIOS or
ACPI, load the new legacy_serial module (or build 8250 static) with
the "legacy_serial.force" option.
[akpm@linux-foundation.org: fix makefiles]
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Keith Owens <kaos@ocs.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Russell King <rmk+serial@arm.linux.org.uk>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some obviously old interrupt disable/enable code that has been
commented out.
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serial_txx9 driver have abused device numbers (major 4, minor 128) if
CONFIG_SERIAL_TXX9_STDSERIAL was not set. This patch makes the driver use
proper device numbers assigned for it (major 204, minor 196-203). I
suppose a typical user of this driver set CONFIG_SERIAL_TXX9_STDSERIAL to Y
(i.e. use "ttyS0"), so this patch would not cause big compatibility issue.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The jsm driver doesn't currently use the uart_handle_*_change helper
functions, which are the obvious place for things like linuxpps to tie
into (which it now does of course), and as a result the jsm driver can
not be used with linuxpps and anything else that ties into the
serial_core helper functions. This patch adds calls to these helper
functions whenever the value they manage changes. That actual storage
of the state is not modified since the jsm driver caches the current
settings (The 8250 driver reads them everytime a user asks for the
state), and only updates them whenever they change.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The jsm driver fails when you try to use the TIOCSSERIAL ioctl. The reason
is that the driver never sets uart_port.uartclk, causing the data received
using TIOCGSERIAL to not match the internal state of the driver. This
patch fixes this problem by settings the uartclk to the value used by the
serial_core (16 times the baud base).
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SERIAL] sunsu: Fix section mismatch warnings.
[SPARC64]: pgtable_cache_init() should be __init.
[SPARC64]: Fix section mismatch warnings in arch/sparc64/kernel/prom.c
[SPARC64]: Fix section mismatch warnings in arch/sparc64/kernel/pci.c
[SPARC64]: Fix section mismatch warnings in arch/sparc64/kernel/console.c
[MM]: sparse_init() should be __init.
[SPARC64]: Update defconfig.
[VIDEO]: Add Sun XVR-2500 framebuffer driver.
[VIDEO]: Add Sun XVR-500 framebuffer driver.
[SPARC64]: SUN4U PCI-E controller support.
[SPARC]: Fix comment typo in smp4m_blackbox_current().
[SCSI] SUNESP: sun_esp.c needs linux/delay.h
Fix up conflict in arch/sparc64/mm/init.c manually due to removal of
pgtable_cache_init() through the -mm patches (even though that patch was
also by David ;)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements the driver necessary use the Analog Devices Blackfin
processor's Serial Port.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
serial_core, use pr_debug
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPSC serial driver assumes that interrupt is always on to pick up the
DMA transmit ops that aren't submitted while the DMA engine is active.
However when irqs are off for a period of time such as operations under
kernel crash dump console messages do not show up due to additional DMA ops
are being dropped. This makes console writes to process through all the tx
DMAs queued up before submitting a new request.
Also, the current locking mechanism does not protect the hardware registers
and ring buffer when a printk is done during the serial write operations.
The additional per port transmit lock provides a finer granular locking and
protects registers being clobbered while printks are nested within UART
writes.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At present, the serial core always allows setserial in userspace to change the
port address, irq and base clock of any serial port. That makes sense for
legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports
at peculiar addresses. In these cases, the kernel code configuring the ports
must know exactly where they are, and their clocking arrangements (which can
be unusual on embedded boards). It doesn't make sense for userspace to change
these settings.
Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port
structure. If this flag is set when the serial port is configured, any
attempts to alter the port's type, io address, irq or base clock with
setserial are ignored.
In addition this patch uses the new flag for on-chip serial ports probed in
arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports
probed by drivers/serial/of_serial.c.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial driver patch for the PMC-Sierra MSP71xx devices.
There are three different fixes:
1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard
16550 in that the THRE interrupt will not re-assert itself simply by
disabling and re-enabling the THRI bit in the IER, it is only re-enabled
if a character is actually sent out.
It appears that the "8250-uart-backup-timer.patch" in the "mm" tree
also fixes it so we have dropped our initial workaround. This patch now
needs to be applied on top of that "mm" patch.
2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature
which causes a new Busy Detect interrupt to be generated if it's busy
when the LCR is written. This fix saves the value of the LCR and
rewrites it after clearing the interrupt.
3 Workaround for interrupt/data concurrency issue: The SoC needs to
ensure that writes that can cause interrupts to be cleared reach the UART
before returning from the ISR. This fix reads a non-destructive register
on the UART so the read transaction completion ensures the previously
queued write transaction has also completed.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the serial port gets shut down, then console output stalls. 9 out
of 10 kernel hackers agree, this is a bad thing.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark sunsu_console_setup() as __init and rename 'sunsu_cons'
to 'sunsu_console' so that it matches modpost.c's whitelist.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the enable/disable hooks for the port clock to sh-sci.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the GDB stub being entered via a special sysrq trigger,
we don't want to hit it directly from sci_br_interrupt().
Without this, there is access to the other sysrq triggers when
kgdb is enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves the i.MX UART register descriptions from
include/asm-arm/arch-imx/imx-regs.h to the serial driver itself.
This helps using the driver on other architectures like mx31
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow slower serial baud-rates by switching the UART clock from MCK to
MCK/8.
Based on patches by Mike Wolfram and Russell King.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 40b36daa introduced possibility that serial8250_backup_timeout() ->
serial8250_handle_port() locks port.lock without disabling irqs, thus
allowing deadlock against interrupt handler (port.lock is acquired in
serial8250_interrupt()).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two functions are called from __devinit context, but they are marked as
__init. Fix this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
irq values are u32, not u8. Large irq numbers will be truncated,
free_irq may free a different irq.
Remove incorrectly sized struct member and use the one from pci_dev.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I encountered the following kernel panic. The cause of this problem was
NULL pointer access in check_modem_status() in 8250.c. I confirmed this
problem is fixed by the attached patch, but I don't know this is the
correct fix.
sadc[4378]: NaT consumption 2216203124768 [1]
Modules linked in: binfmt_misc dm_mirror dm_mod thermal processor fan
container button sg e100 eepro100 mii ehci_hcd ohci_hcd
Pid: 4378, CPU 0, comm: sadc
psr : 00001210085a2010 ifs : 8000000000000289 ip : [<a000000100482071>]
Not tainted
ip is at check_modem_status+0xf1/0x360
Call Trace:
[<a000000100013940>] show_stack+0x40/0xa0
[<a0000001000145a0>] show_regs+0x840/0x880
[<a0000001000368e0>] die+0x1c0/0x2c0
[<a000000100036a30>] die_if_kernel+0x50/0x80
[<a000000100037c40>] ia64_fault+0x11e0/0x1300
[<a00000010000bdc0>] ia64_leave_kernel+0x0/0x280
[<a000000100482070>] check_modem_status+0xf0/0x360
[<a000000100482300>] serial8250_get_mctrl+0x20/0xa0
[<a000000100478170>] uart_read_proc+0x250/0x860
[<a0000001001c16d0>] proc_file_read+0x1d0/0x4c0
[<a0000001001394b0>] vfs_read+0x1b0/0x300
[<a000000100139cd0>] sys_read+0x70/0xe0
[<a00000010000bc20>] ia64_ret_from_syscall+0x0/0x20
[<a000000000010620>] __kernel_syscall_via_break+0x0/0x20
Fix the possible NULL pointer access in check_modem_status() in 8250.c. The
check_modem_status() would access 'info' member of uart_port structure, but it
is not initialized before uart_open() is called. The check_modem_status() can
be called through /proc/tty/driver/serial before uart_open() is called.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi2005@soft.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the AMBA PL010 serial driver to use the clock infrastructure
to allow EP93xx platforms to properly gate the clock to the UARTs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use a pointer to struct uart_amba_port throughout the driver
rather than a mixture of that and struct uart_port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds device ids of two Fujitsu Siemens Tablet PCs to pnp_dev_table
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sh-sci sci_br_interrupt() handler was failing to call
in to uart_handle_break(), which was something that only
the SH-3 path was doing, fix that up.
Additionally, SUPPORT_SYSRQ seems to have moved down too
far, move it back to the top so uart_handle_break() and
friends aren't no-ops.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sn console driver was snagged by the use of CONFIG_DEBUG_SHIRQ!
The request_irq() immediate call to the interrupt handler caused
another attempt to lock the port lock - deadlock.
This is a patch to fix that.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the Freescale M5282 ColdFire,
Port UA Pin Assignment Register should set to UART mode.
Patch submitted by David Wu <davidwu@arcturusnetworks.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove remaining references to saved registers now that
uart_handle_sysrq_char() does not want them.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (34 commits)
[POWERPC] 86xx: Cleaned up platform dts files
[POWERPC] 85xx: Renamed MPC8568 MDS board code to match other boards
[POWERPC] 85xx: Cleaning up machine probing
[POWERPC] QE: clean up ucc_slow.c and ucc_fast.c
[POWERPC] 85xx: Cleaned up platform dts files
[POWERPC] 83xx: Renamed MPC8323 MDS dts and defconfig to match other boards
[POWERPC] 83xx: Updated and renamed MPC8360PB to MPC836x MDS
[POWERPC] 83xx: Use of_platform_bus_probe to setup QE devices
[POWERPC] 83xx: use default value of loops_per_jiffy
[POWERPC] 83xx: Remove obsolete setting of ROOT_DEV.
[POWERPC] 83xx: Cleaning up machine probing and board initcalls
[POWERPC] Dispose irq mapping when done in mpc52xx_serial.c
[POWERPC] 86xx: Add missing of_node_put() in mpc86xx_hpcn_init_irq().
[POWERPC] 8[56]xx: Remove obsolete setting of ROOT_DEV for 85xx and 86xx platforms.
[POWERPC] pseries: Enabling auto poweron after power is restored.
[POWERPC] use winbond libata instead of ide driver for pseries CD drives
[POWERPC] powerpc: remove references to the obsolete linux,platform property
[POWERPC] add of_get_mac_address and update fsl_soc.c to use it
[POWERPC] 83xx: Cleaned up 83xx platform dts files
[POWERPC] Fix bug with early ioremap and 64k pages
...
Fix bug that exists in kernel.org since 2.6.17rc4 - compiles fail if
CONFIG_SERIAL_CPM_SMC is defined. Tested on a board using SMC1 console.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since serial devices are powered down when not in use and some of those
devices cannot be accessed when powered down, we need to enable power
around calls to get_mcrtl() when dumping port state via uart_line_info().
This resolves hangs observed on some machines while reading serial device
registers when a port is powered off.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return failure immediately, so we don't have to test it twice.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below works around a minor bug found in the UART of the remote
management card used in many HP ia64 and parisc servers (aka the Diva
UARTs). The problem is that the UART does not reassert the THRE interrupt
if it has been previously cleared and the IIR THRI bit is re-enabled. This
can produce a very annoying failure mode when used as a serial console,
allowing a boot/reboot to hang indefinitely until an RX interrupt kicks it
into working again (ie. an unattended reboot could stall).
To solve this problem, a backup timer is introduced that runs alongside the
standard interrupt driven mechanism. This timer wakes up periodically,
checks for a hang condition and gets characters moving again. This backup
mechanism is only enabled if the UART is detected as having this problem,
so systems without these UARTs will have no additional overhead.
This version of the patch incorporates previous comments from Pavel and
removes races in the bug detection code. The test is now done before the
irq linking to prevent races with interrupt handler clearing the THRE
interrupt. Short delays and syncs are also added to ensure the device is
able to update register state before the result is tested.
Aristeu says:
this was tested on the following HP machines and solved the problem:
rx2600, rx2620, rx1600 and rx1620s.
hpa says:
I have seen this same bug in soft UART IP from "a major vendor."
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This can be used for serial ports that are connected to an
OF platform bus but are not autodetected by the lecacy
serial support.
It will automatically take over devices that come from the
legacy serial detection, which usually is only one device.
In some cases, rtas may be set up to use the serial port
in the firmware, which allows easier debugging before probing
the serial ports. In this case, the "used-by-rtas" property
must be set by the firmware. This patch also adds code to the
legacy serial driver to check for this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Access to chip-internal registers should always be native-endian. This is
especially important for AVR32 since it's a big-endian architecture and the
non-raw readl() and writel() macros are defined to do little-endian
accesses.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the CPCI-ASIO4 quad port CompactPCI UART board from
electronic system design gmbh.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get the Perle quad-modem PCI card (PCI-RAS4) detected by serial driver. It
may also get the PCI-RAS8 running, but can't guarantee as I didn't had one for
testing.
Signed-off-by: Thomas Hoehn <thomas.hoehn@avocent.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the serial_txx9 driver.
* Configurable manumum port number. (SERIAL_TXX9_NR_UARTS)
* Remove some code which is unneeded if CONFIG_PM=n.
* Use PCI_DEVICE() for pci device id table and make it const.
* Do not include <asm/irq.h>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SGI IOC3 and IOC4 PCI devices implement memory space apertures, not I/O
space apertures. Use the appropriate region management functions.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Stanislaw Skowronek <skylark@linux-mips.org>
Cc: Brent Casavant <bcasavan@sgi.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If RTS interrupt is caused by RTS senzing logic inside i.MX UART module the
IRQ type cannot be set.
It applies only for interrupts going through GPIO layer. The problem has
been noticed by Konstantin Kletschke some time ago.
No IRQF_TRIGGER set_type function for IRQ 26 (MPU)
I would not change type to fixed 0, because it could be possible to use
different GPIO MX1 pin for RTS in the theory. On the other hand it is only
for documentation purposes now, because RTS read code would have to be
adjusted in such case.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix occasional tx buffer overflows in the i.MX serial driver which came
from the fact that space in the buffer was checked after sending the first
byte. Also, fifosize is 32 bytes, not 8.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Atmel AT91 and AVR32 processor architectures share many of the same
peripherals. The PDC (Peripheral Data Controller) registers are also
implemented within in a number of the on-chip peripherals (eg, USART,
MMC, SPI, SSC, etc).
In a attempt not to duplicate the register definitions in each
peripheral, or in each architecture, the at91_pdc.h header in
asm-arm/arch-at91 and asm-avr32/arch-at32ap has been replaced with
linux/atmel_pdc.h.
The definitions have also been renamed from AT91_PDC_* to ATMEL_PDC_*,
and the drivers updated accordingly.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:
- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
initial commit,
- new solely-powerpc header file for 8260 family (was using one from
arch/ppc, this one cleaned up from the extra stuff), in fact for now
a placeholder to get the board-specific includes for stuff not yet
capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes cpm uart able to work using OF-passed parameters
in case of CPM stuff (found on most mpc8xx reference and custom
boards). The idea is to keep ppc stuff working yet making it able to be
used for powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using console=ttyAM1 or console=ttyAMA1 resulted in an oops during
boot due to trying to drive the console before that port had been
registered. Fix this by checking whether the port is present before
allowing console setup to proceed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 (and AVR32) serial driver.
It should resolve these kernel messages:
Unbalanced IRQ x wake disable
BUG: warning at kernel/irq/manage.c:167/set_irq_wake()
Original patch from Marc Pignat.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A couple of whitespace cleanups, mainly in the AT91 header files.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
and serial console support is enabled.
o Serial console setup function, serial8250_console_setup(), is a non __init
function and it calls functions which are of type __init().
(uart_parse_options() and uart_set_options()). Assuming, setup will
be called during init time, changing serial8250_console_setup() to __init.
o Adding one more pattern to modpost whitelist. Console drivers might
have *_console structures containing references to setup functions which
can be of __init type. Don't generate warnings for those.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The mpc52xx_uart_of_enumerate() function was added when adding 52xx
support to arch/powerpc, but it must not be called for arch/ppc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to pass in the resource otherwise we cannot
release the region properly. We must know whether it is
an I/O or MEM resource.
Spotted by Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
The uartlite driver used to always enable the port even if request_port
failed causing havoc. This patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial
cards. The JC12xx cards are standard RS232-based serial cards utilising
the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be
supported natively, we will need additional tweaks to the 8250 layers so
we can specify some values for the 950's registers. Hence, these two
entries are commented out.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
Fix inotify maintainers entry
Fix typo in new debug options.
Jon needs a new shift key.
fs: Convert kmalloc() + memset() to kzalloc() in fs/.
configfs.h: Remove dead macro definitions.
kconfig: Standardize "depends" -> "depends on" in Kconfig files
e100: replace kmalloc with kcalloc
um: replace kmalloc+memset with kzalloc
fix typo in net/ipv4/ip_fragment.c
include/linux/compiler.h: reject gcc 3 < gcc 3.2
Kconfig: fix spelling error in config KALLSYMS help text
Remove duplicate "have to" in comment
Fix small typo in drivers/serial/icom.c
Use consistent casing in help message
EXT{2,3,4}_FS: remove outdated part of the help text
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
