Sometimes boards don't reset properly, and the address read out of the
EEPROM is zero. Stop the insanity before the device gets registered.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side code has a number of ring problems that caused some
of the Bugzilla reports. Rather than trying to fix the details, it is safer
to rewrite the code that handles transmit completion and freeing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consolidate all usage of ring low water mark to one value.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since accessing the PHY can take 100's of usecs, use a work queue to
allow spinning in outside of soft/hard irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch updates the myri10ge to 1.0.0, with the following changes:
* Switch to dma_alloc_coherent API.
* Avoid PCI burst when writing the firmware on chipset with unaligned completions.
* Use ethtool_op_set_tx_hw_csum instead of ethtool_op_set_tx_csum.
* Include linux/dma-mapping.h to bring DMA_32/64BIT_MASK on all architectures
(was missing at least on alpha).
* Some typo and warning fixes.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
drivers/net/myri10ge/myri10ge.c | 57 +++++++++++++++++++-----------
1 file changed, 37 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BRIDGE]: fix locking and memory leak in br_add_bridge
[IRDA]: Missing allocation result check in irlap_change_speed().
[PPPOE]: Missing result check in __pppoe_xmit().
[NET]: Eliminate unused /proc/sys/net/ethernet
[NETCONSOLE]: Clean up initcall warning.
[TCP]: Avoid skb_pull if possible when trimming head
skb_clone() may fail, we should check the result.
Coverity CID: 1215.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt Mackall <mpm@selenic.com>
netconsole is being wrong here. If it wasn't enabled there's no error.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
zd1201 is wifi adapter, yet it is hiding in drivers/usb/net where
noone can find it. This moves Kconfig/Makefile zd1201 to the right
place.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug logging in bcm43xx_ieee80211_set_security() is pretty noisy.
Make it more silent.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup coding style and other small stuff in zd1201. No real code
changes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
[PATCH] pcmcia: fix zeroing of cm4000_cs.c data
[PATCH] pcmcia: missing pcmcia_get_socket() result check
From: Andrew Morton <akpm@osdl.org>
drivers/rtc/rtc-m48t86.c: In function `m48t86_rtc_read_time':
drivers/rtc/rtc-m48t86.c:51: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:55: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:56: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:57: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:58: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:60: error: structure has no member named `ia64_mv'
readb() and writeb() are macros on ia64.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Stefan Richter <stefanr@s5r6.in-berlin.de>
I added a failure check in patch "sbp2: variable status FIFO address (fix
login timeout)" --- alas for a wrong error value. This is a bug since
Linux 2.6.16. Leads to NULL pointer dereference if the call failed, and
bogus failure handling if call succeeded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
Cc: Ben Collins <bcollins@debian.org>
Cc: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
The path grouping can fail due to non-unique pathgroup-IDs. The source for
the CPU-ID part of the ID was incorrectly specified on 64 bit systems.
Additionally, the length of the ID was too large due to incorrect data packing
declaration. Fix CPU-ID lowcore address and add missing packing declaration.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Florin Malita <fmalita@gmail.com>
The skb may be gone after netif_rx(), we can't use 'skb->len' to update the
stats. 'pkt_len' should work instead.
Coverity CID: 911.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also add the Poll RX DMA Memory workaround to the DMA4
(xmitstatus) path.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ipoib_stop() is called it first calls netif_stop_queue() to stop
the kernel from passing more packets to the network driver. However,
the completion handler may call netif_wake_queue() re-enabling packet
transfer.
This might result in leaks (we see AH leaks which we think can be
attributed to this bug) as new packets get posted while the interface
is going down.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver is selectable on other than Au1200 Alchemy systems but won't
build nor work - there is no MMC hw.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_lib.c: properly count the number of pages in scsi_req_map_sg()
[SCSI] scsi_transport_sas: make write attrs writeable
[SCSI] scsi_transport_sas; fix user_scan
[SCSI] ppa: fix for machines with highmem
[SCSI] mptspi: reset handler shouldn't be called for other bus protocols
[SCSI] Blacklist entry for HP dat changer
Fix the incorrect calculation of how much to zero out in struct cm4000_dev
on device initialization.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The result of pcmcia_get_socket() may be NULL but ds_event() uses it
without checking.
Coverity CID: 436.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The calculation of nr_pages in scsi_req_map_sg() doesn't account for
the fact that the first page could have an offset that pushes the end
of the buffer onto a new page.
Signed-off-by: Bryan Holty <lgeek@frontiernet.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: NeilBrown <neilb@suse.de>
If an error is reported by a drive in a RAID array (which is done via
bi_end_io - in interrupt context), we call md_error and md_new_event which
calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be
called in interrupt context.
This patch just creates a variant of md_new_event which avoids the sysfs
call, and uses that. A better fix for later is to arrange for the event to
be called from user-context.
Note: avoiding the sysfs call isn't a problem as an error will not, by
itself, modify the sync_action attribute. (We do still need to
wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Jeremy Higdon <jeremy@sgi.com>
This patch fixes a bug in sgiioc4 where it was using the default IDE port
I/O operations instead of MMIO.
The IDE part of the IOC4 chip uses MMIO to map the chip registers.
Unfortunately, the sgiioc4 driver uses the default port IO operations,
which happens to have worked for the past few years. That's about to
change, however, thus this change from inX/outX to readX/writeX.
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Martin Michlmayr <tbm@cyrius.com>
Fix the following compilation error:
CC drivers/video/maxinefb.o
drivers/video/maxinefb.c:58: warning: initializer-string for array of chars is too long
drivers/video/maxinefb.c:58: warning: (near initialization for \u2018maxinefb_fix.id\u2019)
drivers/video/maxinefb.c:110: error: unknown field \u2018fb_get_fix\u2019 specified in initializer
drivers/video/maxinefb.c:110: error: \u2018gen_get_fix\u2019 undeclared here (not in a function)
drivers/video/maxinefb.c:111: error: unknown field \u2018fb_get_var\u2019 specified in initializer
drivers/video/maxinefb.c:111: error: \u2018gen_get_var\u2019 undeclared here (not in a function)
make[2]: *** [drivers/video/maxinefb.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Rodolfo Giometti <giometti@linux.it>
Fix the following warning on compilation:
drivers/video/au1100fb.c: In function `au1100fb_fb_setcolreg':
drivers/video/au1100fb.c:219: warning: ISO C90 forbids mixed declarations and code
drivers/video/au1100fb.c: In function `au1100fb_fb_pan_display':
drivers/video/au1100fb.c:321: warning: ISO C90 forbids mixed declarations and code
drivers/video/au1100fb.c: In function `au1100fb_fb_mmap':
drivers/video/au1100fb.c:387: warning: ISO C90 forbids mixed declarations and code
drivers/video/au1100fb.c: In function `au1100fb_drv_probe':
drivers/video/au1100fb.c:471: warning: unsigned int format, long unsigned int arg (arg 2)
drivers/video/au1100fb.c: At top level:
drivers/video/au1100fb.c:617: warning: initialization from incompatible pointer type
drivers/video/au1100fb.c:618: warning: initialization from incompatible pointer type
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andrew Morton <akpm@osdl.org>
Revert commit ff4da2e262.
It broke APM suspend, probably because APM doesn't switch back to a VT
when suspending.
Tracked down by Matt Mackall <mpm@selenic.com>
Rafael sayeth:
"It only fixed the theoretical issue that a quick-handed user could
switch to X after processes have been frozen and before the devices
are suspended.
With the current userland suspend tools it shouldn't be necessary."
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Corey Minyard <minyard@acm.org>
This patch is pretty important to get in for IPMI, new systems have been
changing the way ACPI and IPMI interact, and this works around the problems
for now. This is a temporary fix until we get proper ACPI handling in
IPMI.
Fixed releasing already-allocated regions when a later request fails, and
forward-ported it to HEAD.
Some BIOSes reserve disjoint I/O regions in their ACPI tables for the IPMI
controller. This causes problems when trying to register the entire I/O
region. Therefore we must register each I/O port separately.
Signed-off-by: Jordan Hargrave <Jordan_Hargrave@dell.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Seiji Munetoh <seiji.munetoh@gmail.com>
Change the binary output format to actual ACPI TCPA log structure since the
current format does not contain all event-data information that need to
verify the PCRs in TPM. tpm_binary_bios_measurements_show() uses
get_event_name() to convert the binary event-data to ascii format, and puts
them as binary. However, to verify the PCRs, the event-data must be a
actual binary event-data used by SHA1 calc. in BIOS.
So, I think actual ACPI TCPA log is good for this binary output format.
That way, any userland tools easily parse this data with reference to TCG
PC specification.
Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Seiji Munetoh <seiji.munetoh@gmail.com>
Fix "tcpa_pc_event" misalignment between enum, strings and TCG PC spec and
output of the event which contains a hash data.
Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: David Hollister <david.hollister@amd.com>
After the system boots with the logo, if the first action is a scrollback, the
screen may become garbled. This patch ensures that the softback_curr value is
updated along with softback_in following the scrollback.
Signed-off-by: David Hollister <david.hollister@amd.com>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] VIA PT880 Ultra support.
[AGPGART] Fix Nforce3 suspend on amd64.
[AGPGART] Enable SIS AGP driver on x86-64 for EM64T systems
Added different lifebook-versions and the CF-18 to the corresponding
dmi-table.
Signed-off-by: Kenan Esau <kenan.esau@conan.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove the numbered SW_* entries from the input system and assign names
to the existing users.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Correct touchpad left & right keys assignments for ALPS_OLDPROTO
that were swapped. Old protocol is used on UMAX ActionBook-530T
notebook.
Signed-off-by: Yotam Medini <yotam.medini@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In sw_connect we leak 'buf' and 'idbuf' when we do not leave via one of
the fail* labels. This was spotted by the coverity checker.
Patch is compile tested only due to lack of hardware.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
