2017-01-17 13:50:18 +00:00
# This file allows user to override the factory
# defaults for the WLAN Driver
# Enable IMPS or not
gEnableImps = 1
# Enable/Disable Idle Scan
gEnableIdleScan = 0
# Increase sleep duration (seconds) during IMPS
2017-01-17 14:01:14 +00:00
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
2017-01-17 13:50:18 +00:00
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime = 0
2018-04-19 01:04:32 +00:00
# This parameter is the continuous packets dropping threshold
# that will trigger kickout peer event from fw.
# MIN value (0) will disable the kickout feature.
# MAX value (1024)
gDroppedPktDisconnectTh = 1024
2017-01-17 13:50:18 +00:00
# Enable BMPS or not
gEnableBmps = 1
# Enable suspend or not
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
gEnableSuspend = 3
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
2017-01-17 14:01:14 +00:00
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
# 7 = 11b only 8 = 11ac only.
2017-01-17 13:50:18 +00:00
gDot11Mode = 0
# CSR Roaming Enable(1) Disable(0)
gRoamingTime = 0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress = 000AF58989FF
Intf1MacAddress = 000AF58989FE
Intf2MacAddress = 000AF58989FD
Intf3MacAddress = 000AF58989FC
# UAPSD service interval for VO,VI, BE, BK traffic
2017-01-17 14:01:14 +00:00
InfraUapsdVoSrvIntv = 0
InfraUapsdViSrvIntv = 0
InfraUapsdBeSrvIntv = 0
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
InfraUapsdBkSrvIntv = 0
2017-01-17 13:50:18 +00:00
# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff = 1
# Make 1x1 the default antenna configuration
gNumRxAnt = 1
# Beacon filtering frequency (unit in beacon intervals)
gNthBeaconFilter = 50
# Enable WAPI or not
# WAPIIsEnabled=0
# Flags to filter Mcast abd Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter = 3
#Flag to enable HostARPOffload feature or not
hostArpOffload = 1
2017-01-17 14:01:14 +00:00
#Flag to enable TCPChkSumOffld feature or not
gEnableTCPChkSumOffld = 1
#Flag to enable HostNSOffload feature or not
hostNSOffload = 1
#Flag to enable IPChkSumOffld feature or not
gEnableIPChecksumOffload = 1
2017-01-17 13:50:18 +00:00
#SoftAP Related Parameters
# AP MAc addr
gAPMacAddr = 000AF589dcab
# 802.11n Protection flag
gEnableApProt = 1
#Enable OBSS protection
gEnableApOBSSProt = 1
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd = 1
# Fixed Rate
gFixedRate = 0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
2017-01-17 14:01:14 +00:00
RTSThreshold = 1048576
2017-01-17 13:50:18 +00:00
# Intra-BSS forward
gDisableIntraBssFwd = 0
# WMM Enable/Disable
WmmIsEnabled = 0
# 802.11d support
g11dSupportEnabled = 0
2017-01-17 14:01:14 +00:00
# 802.11h support
g11hSupportEnabled = 1
# DFS Master Capability
gEnableDFSMasterCap = 1
# ESE Support and fast transition
EseEnabled = 1
2017-01-17 13:50:18 +00:00
ImplicitQosIsEnabled = 0
gNeighborScanTimerPeriod = 200
2017-01-17 14:01:14 +00:00
gNeighborLookupThreshold = 76
gNeighborReassocThreshold = 81
2017-01-17 13:50:18 +00:00
gNeighborScanChannelMinTime = 20
gNeighborScanChannelMaxTime = 30
2017-01-17 14:01:14 +00:00
gMaxNeighborReqTries = 3
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
2017-01-17 13:50:18 +00:00
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled = 1
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
2017-01-17 14:01:14 +00:00
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
2017-01-17 13:50:18 +00:00
#the RSSI of the new/roamable AP should be for roaming
2017-01-17 14:01:14 +00:00
RoamRssiDiff = 3
# If the RSSI of any available candidate is better than currently associated
# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
# registering for reassoc threshold).
# NOTE: Value of 0 means that we would register for reassoc threshold.
gImmediateRoamRssiDiff = 10
# To enable, set gRoamIntraBand=1 (Roaming within band)
# To disable, set gRoamIntraBand=0 (Roaming across band)
gRoamIntraBand = 0
2017-01-17 13:50:18 +00:00
# SAP Country code
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
# Example
# US Indoor, USI
# Korea Outdoor, KRO
# Japan without optional byte, JP
# France without optional byte, FR
#gAPCntryCode=USI
#Short Guard Interval Enable/disable
gShortGI20Mhz = 1
gShortGI40Mhz = 1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff = 0
2017-01-17 14:01:14 +00:00
#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
gWlanAutoShutdown = 0
2017-01-17 13:50:18 +00:00
# Listen Energy Detect Mode Configuration
# Valid values 0-128
# 128 means disable Energy Detect feature
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
# 10-128 are reserved.
# The EDET threshold mapping is as follows in 3dB step:
# 0 = -60 dBm
# 1 = -63 dBm
# 2 = -66 dBm
# ...
# 7 = -81 dBm
# 8 = -84 dBm
# 9 = -87 dBm
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
#
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
#
gEnablePhyAgcListenMode = 128
#Preferred band (both or 2.4 only or 5 only)
BandCapability = 0
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
2017-01-17 14:01:14 +00:00
enableBeaconEarlyTermination = 0
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
beaconEarlyTerminationWakeInterval = 3
2017-01-17 13:50:18 +00:00
#Channel Bonding
gChannelBondingMode5GHz = 1
#Enable Keep alive with non-zero period value
2017-01-17 14:01:14 +00:00
gStaKeepAlivePeriod = 30
2017-01-17 13:50:18 +00:00
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
2017-01-17 14:01:14 +00:00
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
2017-01-17 13:50:18 +00:00
#For both active and power save clients.
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
2017-01-17 14:01:14 +00:00
#If doesn't honor for 5 seconds then DUT remove client.
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
2017-01-17 13:50:18 +00:00
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
2017-01-17 14:01:14 +00:00
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
2017-01-17 13:50:18 +00:00
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
#where we send NULL frame.
2018-07-08 02:16:31 +00:00
#gApLinkMonitorPeriod = 10
2017-01-17 13:50:18 +00:00
2018-07-08 02:16:31 +00:00
#gGoLinkMonitorPeriod = 10
2017-01-17 13:50:18 +00:00
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
2017-01-17 14:01:14 +00:00
2018-07-08 02:16:31 +00:00
gGoKeepAlivePeriod = 20
2017-01-17 14:01:14 +00:00
2018-07-08 02:16:31 +00:00
gApKeepAlivePeriod = 20
2017-01-17 14:01:14 +00:00
2017-01-17 13:50:18 +00:00
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
2017-01-17 14:01:14 +00:00
gEnableBypass11d = 1
2017-01-17 13:50:18 +00:00
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan = 1
2017-01-17 14:01:14 +00:00
# Enable DFS channel roam
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
gAllowDFSChannelRoam = 1
gVhtChannelWidth = 2
2017-01-17 13:50:18 +00:00
# Enable Automatic Tx Power control
gEnableAutomaticTxPowerControl = 1
# 0 for OLPC 1 for CLPC and SCPC
gEnableCloseLoop = 1
#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout = 200
2017-01-17 14:01:14 +00:00
# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS = 2
gVhtTxMCS = 2
# VHT Tx/Rx MCS values for 2x2
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS2x2 = 2
gVhtTxMCS2x2 = 2
# Valid chain mask values
# 01 - enables chain0
# 02 - enables chain1
# 03 - enables both chain 0 and chain 1
# if set to 0 or 1 then all vdevs comes up in 1x1 mode in that band.
gChainMask_2g = 3
gChainMask_5g = 3
# NSS cfg bit definition.
# STA BIT[0:1]
# SAP BIT[2:3]
# P2P_GO BIT[4:5]
# P2P_CLIENT BIT[6:7]
# IBSS BIT[8:9]
# TDLS BIT[10:11]
# P2P_DEVICE BIT[12:13]
# OCB BIT[14:15]
# Valid values are 1 or 2 for each two bit configuration.
# if 2-bit value is set to 1 then the corresponidng vdev comes up in 1x1 mode
# in the band, if set to 2 then that vdev comes up in 2x2 mode in that band.
gVdevTypeNss_2g = 43690
gVdevTypeNss_5g = 43690
2017-01-17 13:50:18 +00:00
# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
2018-07-08 02:16:31 +00:00
gActiveMaxChannelTime = 40
gActiveMinChannelTime = 20
2017-01-17 14:01:14 +00:00
#If set to 0, MCC is not allowed.
gEnableMCCMode = 1
# MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band
gWlanMccToSccSwitchMode = 0
# 1=enable STBC; 0=disable STBC
gEnableRXSTBC = 1
# 1=enable tx STBC; 0=disable
gEnableTXSTBC = 1
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# 1=enable rx LDPC; 0=disable
gEnableRXLDPC = 1
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# Enable Tx beamforming in VHT20MHz
# Valid values are 0,1. If commented out, the default value is 0.
# 0=disable, 1=enable
gEnableTxBFin20MHz = 0
gTxBFEnable = 0
# Enable Active mode offload
gEnableActiveModeOffload = 1
#Enable Scan Results Aging based on timer
#Timer value is in seconds
#If Set to 0 it will not enable the feature
gScanAgingTime = 0
#Enable Scan Results Aging based on number of scans
2017-04-18 10:34:21 +00:00
gScanResultAgeCount = 1
2017-01-17 14:01:14 +00:00
#Enable Power saving mechanism Based on Android Framework
#If set to 0 Driver internally control the Power saving mechanism
#If set to 1 Android Framwrok control the Power saving mechanism
isAndroidPsEn = 0
#Enable thermal mitigation
gThermalMitigationEnable = 0
gEnableFastRoamInConcurrency = 1
#List of Country codes for which 11ac needs to be disabled
#Each country code must be delimited by comma(,)
gListOfNon11acCountryCode = RU,UA,ZA
#Maxium Channel time in msec
gMaxMediumTime = 6000
2017-01-17 13:50:18 +00:00
# 802.11K support
gRrmEnable = 1
2018-05-02 02:05:26 +00:00
gRrmOperChanMax = 7
gRrmNonOperChanMax = 7
2017-01-17 13:50:18 +00:00
gRrmRandIntvl = 100
#Scan offload
2017-01-17 14:01:14 +00:00
gEnableDirectedScanOffload = 1
2017-01-17 13:50:18 +00:00
#FlexConnect Power Factor
#Default is set to 0 (disable)
gFlexConnectPowerFactor = 0
2017-01-17 14:01:14 +00:00
#Disable split scan, the FW will take care of it
gNumChanCombinedConc = 60
#Enable Power Save offload
2018-06-01 11:12:44 +00:00
gEnablePowerSaveOffload = 1
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
#Enable firmware uart print
gEnablefwprint = 0
#Enable firmware log
2018-07-09 19:43:47 +00:00
gEnablefwlog = 0
2017-01-17 14:01:14 +00:00
# Additional firmware log levels
#gFwDebugLogLevel=4
#gFwDebugModuleLoglevel=1,0,2,0,4,0,5,0,6,0,7,4,8,0,9,0,11,0,13,0,17,0,18,0,19,0,27,0,29,0,31,0,35,0,36,0,38,0
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
#IPA config
gIPAConfig = 0
gIPADescSize = 800
gIPAPreFilterEnable = 1
gIPARMEnable = 1
gIPAIPv6Enable = 1
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
#P2P Listen offload
gEnableP2pListenOffload = 1
# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets)
gVhtMpduLen = 2
# Maximum number of wow filters required
#gMaxWoWFilters=22
# WOW Enable/Disable.
# 0 - Disable both magic pattern match and pattern byte match.
# 1 - Enable magic pattern match on all interfaces.
# 2 - Enable pattern byte match on all interfaces.
# 3 - Enable both magic patter and pattern byte match on all interfaces.
# Default value of gEnableWoW is 3.
# gEnableWoW=0
# Enable or Disable MCC Adaptive Scheduler at the FW
# 1=Enable (default), 0=Disable
gEnableMCCAdaptiveScheduler = 1
#Enable or Disable p2p device address administered
isP2pDeviceAddrAdministrated = 1
# RX packet handling options
# 0: no rx thread, no RPS, for MDM
# 1: RX thread
# 2: RPS
rxhandle = 1
# Set RPS CPU MAP as 0xe for the 4 RX queues
# This allows use of CPU1-CPU3 but not CPU0 for 4 RX queues
rpsRxQueueCpuMapList = c
# Set Thermal Power limit
TxPower2g = 20
TxPower5g = 18
# Remove Overlap channel restriction
gEnableOverLapCh = 0
#Enable VHT on 2.4Ghz
gEnableVhtFor24GHzBand = 1
#Enable or Disable 5G early beacon termination
gEnable5gEBT = 1
#Maximum number of offload peers supported
# gMaxOffloadPeers=2
# controlling the following offload patterns
# through ini parameter. Default value is 1
# to disable set it to zero. ssdp = 0
# Setup multicast pattern for mDNS 224.0.0.251,
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
2017-04-18 10:34:21 +00:00
2017-01-17 14:01:14 +00:00
ssdp = 0
#Enable Memory Deep Sleep
gEnableMemDeepSleep = 1
2018-07-09 19:43:47 +00:00
#Disable packet log feature
gEnablePacketLog = 0
2017-01-17 14:01:14 +00:00
# Bus bandwidth threshold values in terms of number of packets
gBusBandwidthHighThreshold = 2000
gBusBandwidthMediumThreshold = 500
gBusBandwidthLowThreshold = 150
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# IPA bandwidth voting
gIPAHighBandwidthMbps = 800
gIPAMediumBandwidthMbps = 400
gIPALowBandwidthMbps = 200
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# Bus bandwidth compute timeout value in ms
gBusBandwidthComputeInterval = 100
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# Regulatory Setting; 0=STRICT; 1=CUSTOM
gRegulatoryChangeCountry = 1
# RA filtering rate limit param, the current value would not
# help if the lifetime in RA is less than 3*60=3min. Then
# we need to change it, though it is uncommon.
gRAFilterEnable = 1
gRArateLimitInterval = 600
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# Maximum number of concurrent connections
gMaxConcurrentActiveSessions = 2
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# Disable/Enable GreenAP
# 0 to disable, 1 to enable, default: 1
gEnableGreenAp = 1
# Radar PRI multiplier
gDFSradarMappingPriMultiplier = 4
gPNOScanSupport = 0
# Enable/Disable RX full reorder offload
gReorderOffloadSupported = 1
# Enable/Disable LPASS support
# 0 to disable, 1 to enable
gEnableLpassSupport = 1
# Whether userspace country code setting shld have priority
gCountryCodePriority = 1
# Enable(1)/Disable(0) SIFS burst
gEnableSifsBurst = 3
# Enable/Disable channel avoidance for SAP in SCC scenario
# 0 - disable
# 1 - enable
gSapSccChanAvoidance = 0
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
gIbssTxSpEndInactivityTime = 10
# Enable/Disable Roaming Offload Support (a.k.a Key Management Offload)
# 0 to disable, 1 to enable
gRoamOffloadEnabled = 0
# Enable support for TDLS
# 0 - disable
# 1 - enable
gEnableTDLSSupport = 1
# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
# and RSSI) is met and then will initiate teardown when teardown criteria
# (idle packet count and RSSI) is met.
# 0 - disable
# 1 - enable
gEnableTDLSImplicitTrigger = 1
# Enable TDLS External Control. That is, user space application has to
# first configure a peer MAC in wlan driver towards which TDLS is desired.
# Device will establish TDLS only towards those configured peers whenever
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
# when teardown criteria (idle packet count and RSSI) is met. However,
# device will accept TDLS connection if it is initiated from any other peer,
# even if that peer is not configured.
# 0 - disable
# 1 - enable
# For TDLS External Control, Implicit Trigger must also be enabled.
gTDLSExternalControl = 1
# Enable support for TDLS off-channel operation
# 0 - disable
# 1 - enable
# TDLS off-channel operation will be invoked when there is only one
# TDLS connection.
gEnableTDLSOffChannel = 1
IpaUcOffloadEnabled = 1
gIpaUcStaOffload = 1
gEnableSelfRecovery = 1
# Enable or Disable Random MAC (Spoofing)
# 1=Enable, 0=Disable (default)
2017-01-17 13:50:18 +00:00
gEnableMacAddrSpoof = 0
2017-01-17 14:01:14 +00:00
# Enable Auto suspend feature
# When this feature is enabled, it will shutdown the PCIe link
# when inactivity is detected in STA disconnected mode.
# 0 - disable
# 1 - enable
gEnableBusAutoSuspend = 0
# Enable Runtime PM Feature.
# Enabling this feature will put target wow and shutdown pcie link
# when inactivity is detected in WLAN Driver.
# This feature is inactive when beaconing interfaces are active with
# clients associated.
# 0 - disable
# 1 - enable
gRuntimePM = 1
# When gRuntimePM is disabled gRuntimeAutoTime won't take effect.
# The Time is in msec.
# 100 is min, 10000 is max, 500 is default.
gRuntimePMDelay = 500
# Enable to check FW hash if secure FW feature is enabled. It's for defconfig
# builds only since it will be ignored in performance/release builds.
gEnableFWHashCheck = 1
# Enable FW to filter out broadcast packets and wakeup host during runtime PM.
# As APPS is awake during runtime PM, if any application needs the broadcast
# packets OEM's can enable this flag.
# FW will filters the broadcast packets and wakeup host to deliver them during
# runtime suspend.
# This flag will take affect when Runtime PM is enabled
gRuntimePmEnableBcastPattern = 0
# Enable/disable 2x2
# 0 - 1x1 (default)
# 1 - 2x2
gEnable2x2 = 1
# 3=enable both HT/VHT TX LDPC
# 2=enable VHT TX LDPC
# 1=enable HT TX LDPC
# 0=disable
gTxLdpcEnable = 3
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k)
gVhtAmpduLenExponent = 7
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
# SAP auto channel selection configuration
# 0 = disable auto channel selection
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
gApAutoChannelSelection = 0
2017-01-17 13:50:18 +00:00
2017-01-17 14:01:14 +00:00
#SOFTAP Channel Range selection
gAPChannelSelectStartChannel = 1
gAPChannelSelectEndChannel = 11
#SOFTAP Channel Range selection Operating band
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
gAPChannelSelectOperatingBand = 0
# Enable or Disable Multi-user MIMO
# 1=Enable (default), 0=Disable
gEnableMuBformee = 1
gMulticastHostFwMsgs = 0
gSoftApMaxPeers = 10
# To support Multicast filtering
gMCAddrListEnable = 1
#Enable Modulated DTIM
2016-06-06 22:13:35 +00:00
gEnableModulatedDTIM = 2
gMaxLIModulatedDTIM = 6
2017-01-17 14:01:14 +00:00
#Enable 2Tx with BT operation
gTxChainMask1ss = 0
2017-01-17 13:50:18 +00:00
2016-12-01 17:06:05 +00:00
# Set beacon missed count threshold to improve stability
gRoamBmissFirstBcnt = 25
gRoamBmissFinalBcnt = 35
2017-01-17 13:50:18 +00:00
2016-12-01 17:11:58 +00:00
# Prefer connecting to 5Ghz AP
# even if its RSSI is lower by 3dBm than the 2.4Ghz AP
gRoamPrefer5GHz = 1
gSelect5GHzMargin = 3
2017-01-17 13:50:18 +00:00
END
# Note: Configuration parser would not read anything past the END marker
2017-01-17 14:01:14 +00:00