commit 172115090f5e739660b97694618a2ba86457063a upstream.
Without this flag some versions of these enclosures do not work.
Reported-and-tested-by: Christian Schaller <cschalle@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 948fa13504f80b9765d2b753691ab94c83a10341 upstream.
If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 18cc2f4cbbaf825a4fedcf2d60fd388d291e0a38 upstream.
Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)
With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.
A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and and Split transaction errors for LS/FS
interrupt devices.
Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.
The default size used to be 64 TRBs per segment
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit d104d0152a97fade389f47635b73a9ccc7295d0b upstream.
Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.
This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.
Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 6e9eac2dcee5e19f125967dd2be3e36558c42fff upstream.
If any memory allocation in resize_stripes fails we will return
-ENOMEM, but in some cases we update conf->pool_size anyway.
This means that if we try again, the allocations will be assumed
to be larger than they are, and badness results.
So only update pool_size if there is no error.
This bug was introduced in 2.6.17 and the patch is suitable for
-stable.
Fixes: ad01c9e375 ("[PATCH] md: Allow stripes to be expanded in preparation for expanding an array")
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit ebe9cb3bb13e7b9b281969cd279ce70834f7500f upstream.
If we find a non-confirmed openowner we jump to exit the function, but do
not set an error value. Fix this by factoring out a helper to do the
check and properly set the error from nfsd4_validate_stateid.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[lizf: adjust the changes for nfsd4_validate_stateid()]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 82ee3aeb9295c5fc37fd2ddf20f13ac2b40ec97d upstream.
Samsung has just released a portable USB3 SSD, coming in a very small
and nice form factor. It's USB ID is 04e8:8001, which unfortunately is
already used by the Palm Visor driver for the Samsung I330 phone cradle.
Having pl2303 or visor pick up this device ID results in conflicts with
the usb-storage driver, which handles the newly released portable USB3
SSD.
To work around this conflict, I've dug up a mailing list post [1] from a
long time ago, in which a user posts the full USB descriptor
information. The most specific value in this appears to be the interface
class, which has value 255 (0xff). Since usb-storage requires an
interface class of 0x8, I believe it's correct to disambiguate the two
devices by matching on 0xff inside visor.
[1] http://permalink.gmane.org/gmane.linux.usb.user/4264
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 48ef23a4f686b1e4519d4193c20d26834ff810ff upstream.
This phone is already supported by the visor driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit c735ed74d83f8ecb45c4c4c95a16853c9c3c8157 upstream.
Added the USB serial console device ID for KCF Technologies PRN device
which has a USB port for its serial console.
Signed-off-by: Mark Edwards <sonofaforester@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 414b7e3b9ce8b0577f613e656fdbc36b34b444dd upstream.
The USB mini-driver in rtlwifi, which is used by rtl8192cu, issues a call to
usb_control_msg() with a timeout value of 0. In some instances where the
interface is shutting down, this infinite wait results in a CPU deadlock. A
one second timeout fixes this problem without affecting any normal operations.
This bug is reported at https://bugzilla.novell.com/show_bug.cgi?id=927786.
Reported-by: Bernhard Wiedemann <bwiedemann@suse.com>
Tested-by: Bernhard Wiedemann <bwiedemann@suse.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Bernhard Wiedemann <bwiedemann@suse.com>
Cc: Takashi Iwai<tiwai@suse.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 09c5b4803a80a5451d950d6a539d2eb311dc0fb1 upstream.
When the LPM policy is set to ATA_LPM_MAX_POWER, the device might
generate a spurious PHY event that cuases errors on the link.
Ignore this event if it occured within 10s after the policy change.
The timeout was chosen observing that on a Dell XPS13 9333 these
spurious events can occur up to roughly 6s after the policy change.
Link: http://lkml.kernel.org/g/3352987.ugV1Ipy7Z5@xps13
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 8393b811f38acdf7fd8da2028708edad3e68ce1f upstream.
This is a preparation commit that will allow to add other criteria
according to which PHY events should be dropped.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b1432a2a35565f538586774a03bf277c27fc267d upstream.
There is a race window in dlm_get_lock_resource(), which may return a
lock resource which has been purged. This will cause the process to
hang forever in dlmlock() as the ast msg can't be handled due to its
lock resource not existing.
dlm_get_lock_resource {
...
spin_lock(&dlm->spinlock);
tmpres = __dlm_lookup_lockres_full(dlm, lockid, namelen, hash);
if (tmpres) {
spin_unlock(&dlm->spinlock);
>>>>>>>> race window, dlm_run_purge_list() may run and purge
the lock resource
spin_lock(&tmpres->spinlock);
...
spin_unlock(&tmpres->spinlock);
}
}
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit d8fd150fe3935e1692bf57c66691e17409ebb9c1 upstream.
The range check for b-tree level parameter in nilfs_btree_root_broken()
is wrong; it accepts the case of "level == NILFS_BTREE_LEVEL_MAX" even
though the level is limited to values in the range of 0 to
(NILFS_BTREE_LEVEL_MAX - 1).
Since the level parameter is read from storage device and used to index
nilfs_btree_path array whose element count is NILFS_BTREE_LEVEL_MAX, it
can cause memory overrun during btree operations if the boundary value
is set to the level parameter on device.
This fixes the broken sanity check and adds a comment to clarify that
the upper bound NILFS_BTREE_LEVEL_MAX is exclusive.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 09789e5de18e4e442870b2d700831f5cb802eb05 upstream.
Currently memory_failure() calls shake_page() to sweep pages out from
pcplists only when the victim page is 4kB LRU page or thp head page.
But we should do this for a thp tail page too.
Consider that a memory error hits a thp tail page whose head page is on
a pcplist when memory_failure() runs. Then, the current kernel skips
shake_pages() part, so hwpoison_user_mappings() returns without calling
split_huge_page() nor try_to_unmap() because PageLRU of the thp head is
still cleared due to the skip of shake_page().
As a result, me_huge_page() runs for the thp, which is broken behavior.
One effect is a leak of the thp. And another is to fail to isolate the
memory error, so later access to the error address causes another MCE,
which kills the processes which used the thp.
This patch fixes this problem by calling shake_page() for thp tail case.
Fixes: 385de35722 ("thp: allow a hwpoisoned head page to be put back to LRU")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Dean Nelson <dnelson@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 16e6bd5970c88a2ac018b84a5f1dd5c2ff1fdf2c upstream.
.. because bind_evtchn_to_cpu(evtchn, cpu) will map evtchn to
'info' and pass 'info' down to xen_evtchn_port_bind_to_cpu().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Annie Li <annie.li@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
[lizf: Backported to 3.4: adjust filename and context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b9d934f27c91b878c4b2e64299d6e419a4022f8d upstream.
After a resume the hypervisor/tools may change console event
channel number. We should re-query it.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 285214409a9e5fceba2215461b4682b6069d8e77 upstream.
When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to
canonize the address family to IPv4, but does not properly process
the listening sockaddr to get the listening port, and does not properly
set the address family of the canonized sockaddr.
Fixes: e51060f08a ("IB: IP address based RDMA connection manager")
Reported-By: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
[lizf: Backported to 3.4:
- there's no cma_save_ip4_info() and cma_save_ip6_info(), and instead
we apply the changes to cma_save_net_info()]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 184af16b09360d6273fd6160e6ff7f8e2482ef23 upstream.
The PM_RESTORE_PREPARE is not handled now in mmc_pm_notify(),
as result mmc_rescan() could be scheduled and executed at
late hibernation restore stages when MMC device is suspended
already - which, in turn, will lead to system crash on TI dra7-evm board:
WARNING: CPU: 0 PID: 3188 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x258/0x374()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in User mode during Functional access
Hence, add missed PM_RESTORE_PREPARE PM event in mmc_pm_notify().
Fixes: 4c2ef25fe0 (mmc: fix all hangs related to mmc/sd card...)
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit fc9e38c0f4d38bfc68b405cf48365d65f7b6319e upstream.
As the interrupt handling was transferred to the pxa_cplds driver,
make the switch in lubbock platform code.
Fixes: 157d2644cb ("ARM: pxa: change gpio to platform device")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 277688639f98a9e34a6f109f9cd6129f92e718c1 upstream.
As the interrupt handling was transferred to the pxa_cplds driver,
make the switch in mainstone platform code.
Fixes: 157d2644cb ("ARM: pxa: change gpio to platform device")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit aa8d6b73ea33c2167c543663ab66039ec94d58f1 upstream.
Historically, this support was in arch/arm/mach-pxa/lubbock.c and
arch/arm/mach-pxa/mainstone.c. When gpio-pxa was moved to drivers/pxa,
it became a driver, and its initialization and probing happened at
postcore initcall. The lubbock code used to install the chained lubbock
interrupt handler at init_irq() time.
The consequence of the gpio-pxa change is that the installed chained irq
handler lubbock_irq_handler() was overwritten in pxa_gpio_probe(_dt)(),
removing :
- the handler
- the falling edge detection setting of GPIO0, which revealed the
interrupt request from the lubbock IO board.
As a fix, move the gpio0 chained handler setup to a place where we have
the guarantee that pxa_gpio_probe() was called before, so that lubbock
handler becomes the true IRQ chained handler of GPIO0, demuxing the
lubbock IO board interrupts.
This patch moves all that handling to a mfd driver. It's only purpose
for the time being is the interrupt handling, but in the future it
should encompass all the motherboard CPLDs handling :
- leds
- switches
- hexleds
The same logic applies to mainstone board.
Fixes: 157d2644cb ("ARM: pxa: change gpio to platform device")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 280227a75b56ab5d35854f3a77ef74a7ad56a203 upstream.
fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[lizf: Backported to 3.4:
- adjust context
- return -EOPNOTSUPP instead of jumping to the "out" label]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit f32393c943e297b8ae180c8f83d81a156c7d0412 upstream.
The incorrect ordering of operations during cpu dlpar add results in invalid
affinity for the cpu being added. The ibm,associativity property in the
device tree is populated with all zeroes for the added cpu which results in
invalid affinity mappings and all cpus appear to belong to node 0.
This occurs because rtas configure-connector is called prior to making the
rtas set-indicator calls. Phyp does not assign affinity information
for a cpu until the rtas set-indicator calls are made to set the isolation
and allocation state.
Correct the order of operations to make the rtas set-indicator
calls (done in dlpar_acquire_drc) before calling rtas configure-connector.
Fixes: 1a8061c46c ("powerpc/pseries: Add kernel based CPU DLPAR handling")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[lizf: Backported to 3.4:
- adjust context
- jump to the "out" lable instead of returning -EINVAL]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 7241ea558c6715501e777396b5fc312c372e11d9 upstream.
Looks like audigy emu10k2 (probably emu10k1 - sb live too) support two
modes for DMA. Second mode is useful for 64 bit os with more then 2 GB
of ram (fixes problems with big soundfont loading)
1) 32MB from 2 GB address space using 8192 pages (used now as default)
2) 16MB from 4 GB address space using 4096 pages
Mode is set using HCFG_EXPANDED_MEM flag in HCFG register.
Also format of emu10k2 page table is then different.
Signed-off-by: Peter Zubaj <pzubaj@marticonet.sk>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 1c94e65c668f44d2c69ae7e7fc268ab3268fba3e upstream.
The OSS emulation in synth-emux helper has a potential AB/BA deadlock
at the simultaneous closing and opening:
close ->
snd_seq_release() ->
sne_seq_free_client() ->
snd_seq_delete_all_ports(): takes client->ports_mutex ->
port_delete() ->
snd_emux_unuse(): takes emux->register_mutex
open ->
snd_seq_oss_open() ->
snd_emux_open_seq_oss(): takes emux->register_mutex ->
snd_seq_event_port_attach() ->
snd_seq_create_port(): takes client->ports_mutex
This patch addresses the deadlock by reducing the rance taking
emux->register_mutex in snd_emux_open_seq_oss(). The lock is needed
for the refcount handling, so move it locally. The calls in
emux_seq.c are already with the mutex, thus they are replaced with the
version without mutex lock/unlock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 6befa9d883385c580369a2cc9e53fbf329771f6d upstream.
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 5c90c07b98c02198d9777a7c4f3047b0a94bf7ed upstream.
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 118c855b5623f3e2e6204f02623d88c09e0c34de upstream.
The 3w-9xxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 9cd9554615cba14f0877cc9972a6537ad2bdde61 upstream.
The 3w-xxxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 579d69bc1fd56d5af5761969aa529d1d1c188300 upstream.
The 3w-sas driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Torsten Luettgert <ml-lkml@enda.eu>
Tested-by: Bernd Kardatzki <Bernd.Kardatzki@med.uni-tuebingen.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 35e9a9f93994d7f7d12afa41169c7ba05513721b upstream.
This works around a issue with qnap iscsi targets not handling large IOs
very well.
The target returns:
VPD INQUIRY: Block limits page (SBC)
Maximum compare and write length: 1 blocks
Optimal transfer length granularity: 1 blocks
Maximum transfer length: 4294967295 blocks
Optimal transfer length: 4294967295 blocks
Maximum prefetch, xdread, xdwrite transfer length: 0 blocks
Maximum unmap LBA count: 8388607
Maximum unmap block descriptor count: 1
Optimal unmap granularity: 16383
Unmap granularity alignment valid: 0
Unmap granularity alignment: 0
Maximum write same length: 0xffffffff blocks
Maximum atomic transfer length: 0
Atomic alignment: 0
Atomic transfer length granularity: 0
and it is *sometimes* able to handle at least one IO of size up to 8 MB. We
have seen in traces where it will sometimes work, but other times it
looks like it fails and it looks like it returns failures if we send
multiple large IOs sometimes. Also it looks like it can return 2 different
errors. It will sometimes send iscsi reject errors indicating out of
resources or it will send invalid cdb illegal requests check conditions.
And then when it sends iscsi rejects it does not seem to handle retries
when there are command sequence holes, so I could not just add code to
try and gracefully handle that error code.
The problem is that we do not have a good contact for the company,
so we are not able to determine under what conditions it returns
which error and why it sometimes works.
So, this patch just adds a new black list flag to set targets like this to
the old max safe sectors of 1024. The max_hw_sectors changes added in 3.19
caused this regression, so I also ccing stable.
Reported-by: Christian Hesse <list@eworm.de>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b421ed15d2c3039eb724680e4de1e4b2bd196a9a upstream.
The number of relocs is passed in by userspace and can be large. It has
been observed to cause kcalloc failures in the wild.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 07b0e5d49d227e3950cb13a3e8caf248ef2a310e upstream.
The emux-synth driver has a possible AB/BA mutex deadlock at unloading
the emu10k1 driver:
snd_emux_free() ->
snd_emux_detach_seq(): mutex_lock(&emu->register_mutex) ->
snd_seq_delete_kernel_client() ->
snd_seq_free_client(): mutex_lock(®ister_mutex)
snd_seq_release() ->
snd_seq_free_client(): mutex_lock(®ister_mutex) ->
snd_seq_delete_all_ports() ->
snd_emux_unuse(): mutex_lock(&emu->register_mutex)
Basically snd_emux_detach_seq() doesn't need a protection of
emu->register_mutex as it's already being unregistered. So, we can
get rid of this for avoiding the deadlock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit d02260824e2cad626fb2a9d62e27006d34b6dedc upstream.
Some models provide too long string for the shortname that has 32bytes
including the terminator, and it results in a non-terminated string
exposed to the user-space. This isn't too critical, though, as the
string is stopped at the succeeding longname string.
This patch fixes such entries by dropping "SB" prefix (it's enough to
fit within 32 bytes, so far). Meanwhile, it also changes strcpy()
with strlcpy() to make sure that this kind of problem won't happen in
future, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit ee52e56e7b12834476cd0031c5986254ba1b6317 upstream.
The mute-LED mode control has the fixed on/off states that are
supposed to remain on/off regardless of the master switch. However,
this doesn't work actually because the vmaster hook is called in the
vmaster code itself.
This patch fixes it by calling the hook indirectly after checking the
mute LED mode.
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 3cab989afd8d8d1bc3d99fef0e7ed87c31e7b647 upstream.
Calling unlazy_walk() in walk_component() and do_last() when we find
a symlink that needs to be followed doesn't acquire a reference to vfsmount.
That's fine when the symlink is on the same vfsmount as the parent directory
(which is almost always the case), but it's not always true - one _can_
manage to bind a symlink on top of something. And in such cases we end up
with excessive mntput().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lizf: Backported to 3.4: drop the changes to do_last()]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 5d05e54af3cdbb13cf19c557ff2184781b91a22c upstream.
Chuck pointed out a problem that crept in with commit 6ffa30d3f734 (nfs:
don't call blocking operations while !TASK_RUNNING). Linux counts tasks
in uninterruptible sleep against the load average, so this caused the
system's load average to be pinned at at least 1 when there was a
NFSv4.1+ mount active.
Not a huge problem, but it's probably worth fixing before we get too
many complaints about it. This patch converts the code back to use
TASK_INTERRUPTIBLE sleep, simply has it flush any signals on each loop
iteration. In practice no one should really be signalling this thread at
all, so I think this is reasonably safe.
With this change, there's also no need to game the hung task watchdog so
we can also convert the schedule_timeout call back to a normal schedule.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Fixes: commit 6ffa30d3f734 (“nfs: don't call blocking . . .”)
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 6ffa30d3f734d4f6b478081dfc09592021028f90 upstream.
Bruce reported seeing this warning pop when mounting using v4.1:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1121 at kernel/sched/core.c:7300 __might_sleep+0xbd/0xd0()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff810ff58f>] prepare_to_wait+0x2f/0x90
Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw snd_hda_codec_generic snd_hda_intel snd_hda_controller snd_hda_codec snd_hwdep snd_pcm snd_timer ppdev joydev snd virtio_console virtio_balloon pcspkr serio_raw parport_pc parport pvpanic floppy soundcore i2c_piix4 virtio_blk virtio_net qxl drm_kms_helper ttm drm virtio_pci virtio_ring ata_generic virtio pata_acpi
CPU: 1 PID: 1121 Comm: nfsv4.1-svc Not tainted 3.19.0-rc4+ #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153950- 04/01/2014
0000000000000000 000000004e5e3f73 ffff8800b998fb48 ffffffff8186ac78
0000000000000000 ffff8800b998fba0 ffff8800b998fb88 ffffffff810ac9da
ffff8800b998fb68 ffffffff81c923e7 00000000000004d9 0000000000000000
Call Trace:
[<ffffffff8186ac78>] dump_stack+0x4c/0x65
[<ffffffff810ac9da>] warn_slowpath_common+0x8a/0xc0
[<ffffffff810aca65>] warn_slowpath_fmt+0x55/0x70
[<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
[<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
[<ffffffff810dd2ad>] __might_sleep+0xbd/0xd0
[<ffffffff8124c973>] kmem_cache_alloc_trace+0x243/0x430
[<ffffffff810d941e>] ? groups_alloc+0x3e/0x130
[<ffffffff810d941e>] groups_alloc+0x3e/0x130
[<ffffffffa0301b1e>] svcauth_unix_accept+0x16e/0x290 [sunrpc]
[<ffffffffa0300571>] svc_authenticate+0xe1/0xf0 [sunrpc]
[<ffffffffa02fc564>] svc_process_common+0x244/0x6a0 [sunrpc]
[<ffffffffa02fd044>] bc_svc_process+0x1c4/0x260 [sunrpc]
[<ffffffffa03d5478>] nfs41_callback_svc+0x128/0x1f0 [nfsv4]
[<ffffffff810ff970>] ? wait_woken+0xc0/0xc0
[<ffffffffa03d5350>] ? nfs4_callback_svc+0x60/0x60 [nfsv4]
[<ffffffff810d45bf>] kthread+0x11f/0x140
[<ffffffff810ea815>] ? local_clock+0x15/0x30
[<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
[<ffffffff81874bfc>] ret_from_fork+0x7c/0xb0
[<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
---[ end trace 675220a11e30f4f2 ]---
nfs41_callback_svc does most of its work while in TASK_INTERRUPTIBLE,
which is just wrong. Fix that by finishing the wait immediately if we've
found that the list has something on it.
Also, we don't expect this kthread to accept signals, so we should be
using a TASK_UNINTERRUPTIBLE sleep instead. That however, opens us up
hung task warnings from the watchdog, so have the schedule_timeout
wake up every 60s if there's no callback activity.
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit bb7ffbf29e76b89a86ca4c3ee0d4690641f2f772 upstream.
nfsd triggered a BUG_ON in net_generic(...) when rpc_pipefs_event(...)
in fs/nfsd/nfs4recover.c was called before assigning ntfsd_net_id.
The following was observed on a MIPS 32-core processor:
kernel: Call Trace:
kernel: [<ffffffffc00bc5e4>] rpc_pipefs_event+0x7c/0x158 [nfsd]
kernel: [<ffffffff8017a2a0>] notifier_call_chain+0x70/0xb8
kernel: [<ffffffff8017a4e4>] __blocking_notifier_call_chain+0x4c/0x70
kernel: [<ffffffff8053aff8>] rpc_fill_super+0xf8/0x1a0
kernel: [<ffffffff8022204c>] mount_ns+0xb4/0xf0
kernel: [<ffffffff80222b48>] mount_fs+0x50/0x1f8
kernel: [<ffffffff8023dc00>] vfs_kern_mount+0x58/0xf0
kernel: [<ffffffff802404ac>] do_mount+0x27c/0xa28
kernel: [<ffffffff80240cf0>] SyS_mount+0x98/0xe8
kernel: [<ffffffff80135d24>] handle_sys64+0x44/0x68
kernel:
kernel:
Code: 0040f809 00000000 2e020001 <00020336> 3c12c00d
3c02801a de100000 6442eb98 0040f809
kernel: ---[ end trace 7471374335809536 ]---
Fixed this behaviour by calling register_pernet_subsys(&nfsd_net_ops) before
registering rpc_pipefs_event(...) with the notifier chain.
Signed-off-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Signed-off-by: Lorenzo Restelli <lorenzo.restelli.ext@nokia.com>
Reviewed-by: Kinlong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 13f6b191aaa11c7fd718d35a0c565f3c16bc1d99 upstream.
Using the indenting we can see the curly braces were obviously intended.
This is a static checker fix, but my guess is that we don't read enough
bytes, because we don't calculate "t_len" correctly.
Fixes: f1d8269802 ('memstick: use fully asynchronous request processing')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b72c186999e689cb0b055ab1c7b3cd8fffbeb5ed upstream.
ptrace_resume() is called when the tracee is still __TASK_TRACED. We set
tracee->exit_code and then wake_up_state() changes tracee->state. If the
tracer's sub-thread does wait() in between, task_stopped_code(ptrace => T)
wrongly looks like another report from tracee.
This confuses debugger, and since wait_task_stopped() clears ->exit_code
the tracee can miss a signal.
Test-case:
#include <stdio.h>
#include <unistd.h>
#include <sys/wait.h>
#include <sys/ptrace.h>
#include <pthread.h>
#include <assert.h>
int pid;
void *waiter(void *arg)
{
int stat;
for (;;) {
assert(pid == wait(&stat));
assert(WIFSTOPPED(stat));
if (WSTOPSIG(stat) == SIGHUP)
continue;
assert(WSTOPSIG(stat) == SIGCONT);
printf("ERR! extra/wrong report:%x\n", stat);
}
}
int main(void)
{
pthread_t thread;
pid = fork();
if (!pid) {
assert(ptrace(PTRACE_TRACEME, 0,0,0) == 0);
for (;;)
kill(getpid(), SIGHUP);
}
assert(pthread_create(&thread, NULL, waiter, NULL) == 0);
for (;;)
ptrace(PTRACE_CONT, pid, 0, SIGCONT);
return 0;
}
Note for stable: the bug is very old, but without 9899d11f65 "ptrace:
ensure arch_ptrace/ptrace_request can never race with SIGKILL" the fix
should use lock_task_sighand(child).
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Pavel Labath <labath@google.com>
Tested-by: Pavel Labath <labath@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit d43698e8abb58a6ac47d16e0f47bb55f452e4fc4 upstream.
Commit 2473238eac ("ihex: add support for CS:IP/EIP records") removes
the "default:" statement in the switch block, making the "return
usage();" line dead code and ihex2fw silently ignoring unknown options.
Restore this statement.
This bug was found by building with HOSTCC=clang and adding
-Wunreachable-code-return to HOSTCFLAGS.
Fixes: 2473238eac ("ihex: add support for CS:IP/EIP records")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 16b8528d20607925899b1df93bfd8fbab98d267c upstream.
We only want to steer the I/O completion towards a queue, but don't
actually access any per-CPU data, so the raw_ version is fine to use
and avoids the warnings when using smp_processor_id().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
[lizf: Backported to 3.4: drop the changes to megasas_build_dcdb_fusion()]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit ca9b590caa17bcbbea119594992666e96cde9c2f upstream.
The current code decreases from the mss size (which is the gso_size
from the kernel skb) the size of the packet headers.
It shouldn't do that because the mss that comes from the stack
(e.g IPoIB) includes only the tcp payload without the headers.
The result is indication to the HW that each packet that the HW sends
is smaller than what it could be, and too many packets will be sent
for big messages.
An easy way to demonstrate one more aspect of the problem is by
configuring the ipoib mtu to be less than 2*hlen (2*56) and then
run app sending big TCP messages. This will tell the HW to send packets
with giant (negative value which under unsigned arithmetics becomes
a huge positive one) length and the QP moves to SQE state.
Fixes: b832be1e40 ('IB/mlx4: Add IPoIB LSO support')
Reported-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 8abaae62f3fdead8f4ce0ab46b4ab93dee39bab2 upstream.
If ib_umem_get() is called with a size equal to 0 and an
non-page aligned address, one page will be pinned and a
0-sized umem will be returned to the caller.
This should not be allowed: it's not expected for a memory
region to have a size equal to 0.
This patch adds a check to explicitly refuse to register
a 0-sized region.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com
Cc: Shachar Raindel <raindel@mellanox.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 0618764cb25f6fa9fb31152995de42a8a0496475 upstream.
I suspect this doesn't show up for most anyone because software
algorithms typically don't have a sense of being too busy. However,
when working with the Freescale CAAM driver it will return -EBUSY on
occasion under heavy -- which resulted in dm-crypt deadlock.
After checking the logic in some other drivers, the scheme for
crypt_convert() and it's callback, kcryptd_async_done(), were not
correctly laid out to properly handle -EBUSY or -EINPROGRESS.
Fix this by using the completion for both -EBUSY and -EINPROGRESS. Now
crypt_convert()'s use of completion is comparable to
af_alg_wait_for_completion(). Similarly, kcryptd_async_done() follows
the pattern used in af_alg_complete().
Before this fix dm-crypt would lockup within 1-2 minutes running with
the CAAM driver. Fix was regression tested against software algorithms
on PPC32 and x86_64, and things seem perfectly happy there as well.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit a87938b2e246b81b4fb713edb371a9fa3c5c3c86 upstream.
With CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE enabled, and a normal top-down
address allocation strategy, load_elf_binary() will attempt to map a PIE
binary into an address range immediately below mm->mmap_base.
Unfortunately, load_elf_ binary() does not take account of the need to
allocate sufficient space for the entire binary which means that, while
the first PT_LOAD segment is mapped below mm->mmap_base, the subsequent
PT_LOAD segment(s) end up being mapped above mm->mmap_base into the are
that is supposed to be the "gap" between the stack and the binary.
Since the size of the "gap" on x86_64 is only guaranteed to be 128MB this
means that binaries with large data segments > 128MB can end up mapping
part of their data segment over their stack resulting in corruption of the
stack (and the data segment once the binary starts to run).
Any PIE binary with a data segment > 128MB is vulnerable to this although
address randomization means that the actual gap between the stack and the
end of the binary is normally greater than 128MB. The larger the data
segment of the binary the higher the probability of failure.
Fix this by calculating the total size of the binary in the same way as
load_elf_interp().
Signed-off-by: Michael Davidson <md@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 2b8760100e1de69b6ff004c986328a82947db4ad upstream.
ACPICA commit aacf863cfffd46338e268b7415f7435cae93b451
It is reported that on a physically 64-bit addressed machine, 32-bit kernel
can trigger crashes in accessing the memory regions that are beyond the
32-bit boundary. The region field's start address should still be 32-bit
compliant, but after a calculation (adding some offsets), it may exceed the
32-bit boundary. This case is rare and buggy, but there are real BIOSes
leaked with such issues (see References below).
This patch fixes this gap by always defining IO addresses as 64-bit, and
allows OSPMs to optimize it for a real 32-bit machine to reduce the size of
the internal objects.
Internal acpi_physical_address usages in the structures that can be fixed
by this change include:
1. struct acpi_object_region:
acpi_physical_address address;
2. struct acpi_address_range:
acpi_physical_address start_address;
acpi_physical_address end_address;
3. struct acpi_mem_space_context;
acpi_physical_address address;
4. struct acpi_table_desc
acpi_physical_address address;
See known issues 1 for other usages.
Note that acpi_io_address which is used for ACPI_PROCESSOR may also suffer
from same problem, so this patch changes it accordingly.
For iasl, it will enforce acpi_physical_address as 32-bit to generate
32-bit OSPM compatible tables on 32-bit platforms, we need to define
ACPI_32BIT_PHYSICAL_ADDRESS for it in acenv.h.
Known issues:
1. Cleanup of mapped virtual address
In struct acpi_mem_space_context, acpi_physical_address is used as a virtual
address:
acpi_physical_address mapped_physical_address;
It is better to introduce acpi_virtual_address or use acpi_size instead.
This patch doesn't make such a change. Because this should be done along
with a change to acpi_os_map_memory()/acpi_os_unmap_memory().
There should be no functional problem to leave this unchanged except
that only this structure is enlarged unexpectedly.
Link: https://github.com/acpica/acpica/commit/aacf863c
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=87971
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=79501
Reported-and-tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reported-and-tested-by: Sial Nije <sialnije@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 9a5cbce421a283e6aea3c4007f141735bf9da8c3 upstream.
We cap 32bit userspace backtraces to PERF_MAX_STACK_DEPTH
(currently 127), but we forgot to do the same for 64bit backtraces.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Zefan Li <lizefan@huawei.com>
