commit e07af133c3e2716db25e3e1e1d9f10c2088e9c1a upstream.
Also known as Verizon U620L.
The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:
$ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4
This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit a91e627e3f0ed820b11d86cdc04df38f65f33a70 upstream.
One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4. For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:
correct: CH345:
0F FE 00 00 0F FE 00 00
04 F0 01 02 04 F0 01 02
04 03 04 05 0F 03 04 05
04 06 07 08 04 06 07 08
04 09 0A 0B 0F 09 0A 0B
04 0C 0D 0E 04 0C 0D 0E
05 F7 00 00 05 F7 00 00
A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored. The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".
These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.
(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 1ca8b201309d842642f221db7f02f71c0af5be2d upstream.
The CH345 USB MIDI chip has two output ports. However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.
It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port. So we can just ignore the device's
descriptors, and hardcode one output port.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 01bb70ae0b98d266fa3e860482c7ce22fa482a6e upstream.
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
root@devkit3250:~# cat /sys/bus/iio/devices/iio\:device0/in_voltage0_raw
------------[ cut here ]------------
WARNING: CPU: 0 PID: 724 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in: sc16is7xx snd_soc_uda1380
CPU: 0 PID: 724 Comm: cat Not tainted 4.3.0-rc2+ #198
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_read_raw+0x38/0x80)
[<>] (lpc32xx_read_raw) from [<>] (iio_read_channel_info+0x70/0x94)
[<>] (iio_read_channel_info) from [<>] (dev_attr_show+0x28/0x4c)
[<>] (dev_attr_show) from [<>] (sysfs_kf_seq_show+0x8c/0xf0)
[<>] (sysfs_kf_seq_show) from [<>] (kernfs_seq_show+0x2c/0x30)
[<>] (kernfs_seq_show) from [<>] (seq_read+0x1c8/0x440)
[<>] (seq_read) from [<>] (kernfs_fop_read+0x38/0x170)
[<>] (kernfs_fop_read) from [<>] (do_readv_writev+0x16c/0x238)
[<>] (do_readv_writev) from [<>] (vfs_readv+0x50/0x58)
[<>] (vfs_readv) from [<>] (default_file_splice_read+0x1a4/0x308)
[<>] (default_file_splice_read) from [<>] (do_splice_to+0x78/0x84)
[<>] (do_splice_to) from [<>] (splice_direct_to_actor+0xc8/0x1cc)
[<>] (splice_direct_to_actor) from [<>] (do_splice_direct+0xa0/0xb8)
[<>] (do_splice_direct) from [<>] (do_sendfile+0x1a8/0x30c)
[<>] (do_sendfile) from [<>] (SyS_sendfile64+0x104/0x10c)
[<>] (SyS_sendfile64) from [<>] (ret_fast_syscall+0x0/0x38)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 6adc5fd6a142c6e2c80574c1db0c7c17dedaa42e upstream.
Proxy entries could have null pointer to net-device.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Fixes: 84920c1420 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2")
Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b81f472a208d3e2b4392faa6d17037a89442f4ce upstream.
Do not update the read stamp after swapping out the reader page from the
write buffer. If the reader page is swapped out of the buffer before an
event is written to it, then the read_stamp may get an out of date
timestamp, as the page timestamp is updated on the first commit to that
page.
rb_get_reader_page() only returns a page if it has an event on it, otherwise
it will return NULL. At that point, check if the page being returned has
events and has not been read yet. Then at that point update the read_stamp
to match the time stamp of the reader page.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 3c25a860d17b7378822f35d8c9141db9507e3beb upstream.
Commit fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 4c6980462f32b4f282c5d8e5f7ea8070e2937725 upstream.
Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.
Fixes: 8229efdaef ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code")
CC: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 7ba0c47c34a1ea5bc7a24ca67309996cce0569b5 upstream.
We need to wait for the flying timers, since we
are going to free the mrtable right after it.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 19cd80a214821f4b558560ebd76bfb2c38b4f3d8 upstream.
It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.
This is clearly a bug and a warning is generated with LOCKDEP too:
WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp]
Modules linked in: ...
CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1
Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012
ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000
ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282
ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508
Call Trace:
...
[<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8109a8bd>] __might_sleep+0x7d/0x90
[<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0
[<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp]
[<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp]
[<ffffffff8121ed98>] __vfs_write+0x28/0xf0
...
Commit 7f477358e2 (usblp: Implement the
ENOSPC convention) moved the set prior locking. So move it back after
the lock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 7f477358e2 ("usblp: Implement the ENOSPC convention")
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 1b8e6a01e19f001e9f93b39c32387961c91ed3cc upstream.
When a passive TCP is created, we eventually call tcp_md5_do_add()
with sk pointing to the child. It is not owner by the user yet (we
will add this socket into listener accept queue a bit later anyway)
But we do own the spinlock, so amend the lockdep annotation to avoid
following splat :
[ 8451.090932] net/ipv4/tcp_ipv4.c:923 suspicious rcu_dereference_protected() usage!
[ 8451.090932]
[ 8451.090932] other info that might help us debug this:
[ 8451.090932]
[ 8451.090934]
[ 8451.090934] rcu_scheduler_active = 1, debug_locks = 1
[ 8451.090936] 3 locks held by socket_sockopt_/214795:
[ 8451.090936] #0: (rcu_read_lock){.+.+..}, at: [<ffffffff855c6ac1>] __netif_receive_skb_core+0x151/0xe90
[ 8451.090947] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff85618143>] ip_local_deliver_finish+0x43/0x2b0
[ 8451.090952] #2: (slock-AF_INET){+.-...}, at: [<ffffffff855acda5>] sk_clone_lock+0x1c5/0x500
[ 8451.090958]
[ 8451.090958] stack backtrace:
[ 8451.090960] CPU: 7 PID: 214795 Comm: socket_sockopt_
[ 8451.091215] Call Trace:
[ 8451.091216] <IRQ> [<ffffffff856fb29c>] dump_stack+0x55/0x76
[ 8451.091229] [<ffffffff85123b5b>] lockdep_rcu_suspicious+0xeb/0x110
[ 8451.091235] [<ffffffff8564544f>] tcp_md5_do_add+0x1bf/0x1e0
[ 8451.091239] [<ffffffff85645751>] tcp_v4_syn_recv_sock+0x1f1/0x4c0
[ 8451.091242] [<ffffffff85642b27>] ? tcp_v4_md5_hash_skb+0x167/0x190
[ 8451.091246] [<ffffffff85647c78>] tcp_check_req+0x3c8/0x500
[ 8451.091249] [<ffffffff856451ae>] ? tcp_v4_inbound_md5_hash+0x11e/0x190
[ 8451.091253] [<ffffffff85647170>] tcp_v4_rcv+0x3c0/0x9f0
[ 8451.091256] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091260] [<ffffffff856181b6>] ip_local_deliver_finish+0xb6/0x2b0
[ 8451.091263] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091267] [<ffffffff85618d38>] ip_local_deliver+0x48/0x80
[ 8451.091270] [<ffffffff85618510>] ip_rcv_finish+0x160/0x700
[ 8451.091273] [<ffffffff8561900e>] ip_rcv+0x29e/0x3d0
[ 8451.091277] [<ffffffff855c74b7>] __netif_receive_skb_core+0xb47/0xe90
Fixes: a8afca0329 ("tcp: md5: protects md5sig_info with RCU")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit e639b8d8a7a728f0b05ef2df6cb6b45dc3d4e556 upstream.
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e ("net: introduce rx_handler results and logic around that")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit c2e703a55245bfff3db53b1f7cbe59f1ee8a4339 upstream.
When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.
Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.
This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.
Fixes: eb2b9311fd ("mac80211: mesh path table implementation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 00ee5927177792a6e139d50b6b7564d35705556a upstream.
If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.
Fixes: 6cb6a27c45 ("net: Call netdev_features_change() from netdev_update_features()")
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 705e63d2b29c8bbf091119084544d353bda70393 upstream.
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e4 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit ed5a377d87dc4c87fb3e1f7f698cba38cd893103 upstream.
now sctp auth cannot work well when setting a hmacid manually, which
is caused by that we didn't use the network order for hmacid, so fix
it by adding the transformation in sctp_auth_ep_set_hmacs.
even we set hmacid with the network order in userspace, it still
can't work, because of this condition in sctp_auth_ep_set_hmacs():
if (id > SCTP_AUTH_HMAC_ID_MAX)
return -EOPNOTSUPP;
so this wasn't working before and thus it won't break compatibility.
Fixes: 65b07e5d0d ("[SCTP]: API updates to suport SCTP-AUTH extensions.")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b582ef5c53040c5feef4c96a8f9585b6831e2441 upstream.
Do not clobber the buffer space passed from `search_binary_handler' and
originally preloaded by `prepare_binprm' with the executable's file
header by overwriting it with its interpreter's file header. Instead
keep the buffer space intact and directly use the data structure locally
allocated for the interpreter's file header, fixing a bug introduced in
2.1.14 with loadable module support (linux-mips.org commit beb11695
[Import of Linux/MIPS 2.1.14], predating kernel.org repo's history).
Adjust the amount of data read from the interpreter's file accordingly.
This was not an issue before loadable module support, because back then
`load_elf_binary' was executed only once for a given ELF executable,
whether the function succeeded or failed.
With loadable module support supported and enabled, upon a failure of
`load_elf_binary' -- which may for example be caused by architecture
code rejecting an executable due to a missing hardware feature requested
in the file header -- a module load is attempted and then the function
reexecuted by `search_binary_handler'. With the executable's file
header replaced with its interpreter's file header the executable can
then be erroneously accepted in this subsequent attempt.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 863e02d0e173bb9d8cea6861be22820b25c076cc upstream.
Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b71b437eedaed985062492565d9d421d975ae845 upstream.
Arnaldo reported that tracepoint filters seem to misbehave (ie. not
apply) on inherited events.
The fix is obvious; filters are only set on the actual (parent)
event, use the normal pattern of using this parent event for filters.
This is safe because each child event has a reference to it.
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20151102095051.GN17308@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 1d512cb77bdbda80f0dd0620a3b260d697fd581d upstream.
If we are using the NO_HOLES feature, we have a tiny time window when
running delalloc for a nodatacow inode where we can race with a concurrent
link or xattr add operation leading to a BUG_ON.
This happens because at run_delalloc_nocow() we end up casting a leaf item
of type BTRFS_INODE_[REF|EXTREF]_KEY or of type BTRFS_XATTR_ITEM_KEY to a
file extent item (struct btrfs_file_extent_item) and then analyse its
extent type field, which won't match any of the expected extent types
(values BTRFS_FILE_EXTENT_[REG|PREALLOC|INLINE]) and therefore trigger an
explicit BUG_ON(1).
The following sequence diagram shows how the race happens when running a
no-cow dellaloc range [4K, 8K[ for inode 257 and we have the following
neighbour leafs:
Leaf X (has N items) Leaf Y
[ ... (257 INODE_ITEM 0) (257 INODE_REF 256) ] [ (257 EXTENT_DATA 8192), ... ]
slot N - 2 slot N - 1 slot 0
(Note the implicit hole for inode 257 regarding the [0, 8K[ range)
CPU 1 CPU 2
run_dealloc_nocow()
btrfs_lookup_file_extent()
--> searches for a key with value
(257 EXTENT_DATA 4096) in the
fs/subvol tree
--> returns us a path with
path->nodes[0] == leaf X and
path->slots[0] == N
because path->slots[0] is >=
btrfs_header_nritems(leaf X), it
calls btrfs_next_leaf()
btrfs_next_leaf()
--> releases the path
hard link added to our inode,
with key (257 INODE_REF 500)
added to the end of leaf X,
so leaf X now has N + 1 keys
--> searches for the key
(257 INODE_REF 256), because
it was the last key in leaf X
before it released the path,
with path->keep_locks set to 1
--> ends up at leaf X again and
it verifies that the key
(257 INODE_REF 256) is no longer
the last key in the leaf, so it
returns with path->nodes[0] ==
leaf X and path->slots[0] == N,
pointing to the new item with
key (257 INODE_REF 500)
the loop iteration of run_dealloc_nocow()
does not break out the loop and continues
because the key referenced in the path
at path->nodes[0] and path->slots[0] is
for inode 257, its type is < BTRFS_EXTENT_DATA_KEY
and its offset (500) is less then our delalloc
range's end (8192)
the item pointed by the path, an inode reference item,
is (incorrectly) interpreted as a file extent item and
we get an invalid extent type, leading to the BUG_ON(1):
if (extent_type == BTRFS_FILE_EXTENT_REG ||
extent_type == BTRFS_FILE_EXTENT_PREALLOC) {
(...)
} else if (extent_type == BTRFS_FILE_EXTENT_INLINE) {
(...)
} else {
BUG_ON(1)
}
The same can happen if a xattr is added concurrently and ends up having
a key with an offset smaller then the delalloc's range end.
So fix this by skipping keys with a type smaller than
BTRFS_EXTENT_DATA_KEY.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 04633df0c43d710e5f696b06539c100898678235 upstream.
When we get loaded by a 64-bit bootloader, kernel entry point is
startup_64 in head_64.S. We don't trust any and all bootloaders because
some will fiddle with CPU configuration so we go ahead and massage each
CPU into sanity again.
For example, some dell BIOSes have this XD disable feature which set
IA32_MISC_ENABLE[34] and disable NX. This might be some dumb workaround
for other OSes but Linux sure doesn't need it.
A similar thing is present in the Surface 3 firmware - see
https://bugzilla.kernel.org/show_bug.cgi?id=106051 - which sets this bit
only on the BSP:
# rdmsr -a 0x1a0
400850089
850089
850089
850089
I know, right?!
There's not even an off switch in there.
So fix all those cases by sanitizing the 64-bit entry point too. For
that, make verify_cpu() callable in 64-bit mode also.
Requested-and-debugged-by: "H. Peter Anvin" <hpa@zytor.com>
Reported-and-tested-by: Bastien Nocera <bugzilla@hadess.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1446739076-21303-1-git-send-email-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 100ceb66d5c40cc0c7018e06a9474302470be73c upstream.
Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo
controllers: Often or even most of the time, the controller is
initialized with the message "added OHCI v1.10 device as card 0, 4 IR +
0 IT contexts, quirks 0x10". With 0 isochronous transmit DMA contexts
(IT contexts), applications like audio output are impossible.
However, OHCI-1394 demands that at least 4 IT contexts are implemented
by the link layer controller, and indeed JMicron JMB38x do implement
four of them. Only their IsoXmitIntMask register is unreliable at early
access.
With my own JMB381 single function controller I found:
- I can reproduce the problem with a lower probability than Craig's.
- If I put a loop around the section which clears and reads
IsoXmitIntMask, then either the first or the second attempt will
return the correct initial mask of 0x0000000f. I never encountered
a case of needing more than a second attempt.
- Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet)
before the first write, the subsequent read will return the correct
result.
- If I merely ignore a wrong read result and force the known real
result, later isochronous transmit DMA usage works just fine.
So let's just fix this chip bug up by the latter method. Tested with
JMB381 on kernel 3.13 and 4.3.
Since OHCI-1394 generally requires 4 IT contexts at a minium, this
workaround is simply applied whenever the initial read of IsoXmitIntMask
returns 0, regardless whether it's a JMicron chip or not. I never heard
of this issue together with any other chip though.
I am not 100% sure that this fix works on the OHCI-1394 part of JMB380
and JMB388 combo controllers exactly the same as on the JMB381 single-
function controller, but so far I haven't had a chance to let an owner
of a combo chip run a patched kernel.
Strangely enough, IsoRecvIntMask is always reported correctly, even
though it is probed right before IsoXmitIntMask.
Reported-by: Clifford Dunn
Reported-by: Craig Moore <craig.moore@qenos.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
[lizf: Backported to 3.4: use dev_notice() instead of ohci_notice()]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit c932b98c1e47312822d911c1bb76e81ef50e389c upstream.
HP ProBook 6550b needs the same pin fixup applied to other HP B-series
laptops with docks for making its headphone and dock headphone jacks
working properly. We just need to add the codec SSID to the list.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=191971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 323c4a02c631d00851d8edc4213c4d184ef83647 upstream.
This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 4afa5f9617927453ac04b24b584f6c718dfb4f45 upstream.
The hash_accept call fails to work on sockets that have not received
any data. For some algorithm implementations it may cause crashes.
This patch fixes this by ensuring that we only export and import on
sockets that have received data.
Reported-by: Harsh Jain <harshjain.prof@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 47796938c46b943d157ac8a6f9ed4e3b98b83cf4 upstream.
This reverts commit a1989b3300.
That commit introduced a regression at least for the case of the SG_IO ioctl()
running without CAP_SYS_RAWIO capability (e.g., unprivileged users) when there
are no active paths: the ioctl() fails with the ENOTTY errno immediately rather
than blocking due to queue_if_no_path until a path becomes active, for example.
That case happens to be exercised by QEMU KVM guests with 'scsi-block' devices
(qemu "-device scsi-block" [1], libvirt "<disk type='block' device='lun'>" [2])
from multipath devices; which leads to SCSI/filesystem errors in such a guest.
More general scenarios can hit that regression too. The following demonstration
employs a SG_IO ioctl() with a standard SCSI INQUIRY command for this objective
(some output & user changes omitted for brevity and comments added for clarity).
Reverting that commit restores normal operation (queueing) in failing scenarios;
tested on linux-next (next-20151022).
1) Test-case is based on sg_simple0 [3] (just SG_IO; remove SG_GET_VERSION_NUM)
$ cat sg_simple0.c
... see [3] ...
$ sed '/SG_GET_VERSION_NUM/,/}/d' sg_simple0.c > sgio_inquiry.c
$ gcc sgio_inquiry.c -o sgio_inquiry
2) The ioctl() works fine with active paths present.
# multipath -l 85ag56
85ag56 (...) dm-19 IBM ,2145
size=60G features='1 queue_if_no_path' hwhandler='0' wp=rw
|-+- policy='service-time 0' prio=0 status=active
| |- 8:0:11:0 sdz 65:144 active undef running
| `- 9:0:9:0 sdbf 67:144 active undef running
`-+- policy='service-time 0' prio=0 status=enabled
|- 8:0:12:0 sdae 65:224 active undef running
`- 9:0:12:0 sdbo 68:32 active undef running
$ ./sgio_inquiry /dev/mapper/85ag56
Some of the INQUIRY command's response:
IBM 2145 0000
INQUIRY duration=0 millisecs, resid=0
3) The ioctl() fails with ENOTTY errno with _no_ active paths present,
for unprivileged users (rather than blocking due to queue_if_no_path).
# for path in $(multipath -l 85ag56 | grep -o 'sd[a-z]\+'); \
do multipathd -k"fail path $path"; done
# multipath -l 85ag56
85ag56 (...) dm-19 IBM ,2145
size=60G features='1 queue_if_no_path' hwhandler='0' wp=rw
|-+- policy='service-time 0' prio=0 status=enabled
| |- 8:0:11:0 sdz 65:144 failed undef running
| `- 9:0:9:0 sdbf 67:144 failed undef running
`-+- policy='service-time 0' prio=0 status=enabled
|- 8:0:12:0 sdae 65:224 failed undef running
`- 9:0:12:0 sdbo 68:32 failed undef running
$ ./sgio_inquiry /dev/mapper/85ag56
sg_simple0: Inquiry SG_IO ioctl error: Inappropriate ioctl for device
4) dmesg shows that scsi_verify_blk_ioctl() failed for SG_IO (0x2285);
it returns -ENOIOCTLCMD, later replaced with -ENOTTY in vfs_ioctl().
$ dmesg
<...>
[] device-mapper: multipath: Failing path 65:144.
[] device-mapper: multipath: Failing path 67:144.
[] device-mapper: multipath: Failing path 65:224.
[] device-mapper: multipath: Failing path 68:32.
[] sgio_inquiry: sending ioctl 2285 to a partition!
5) The ioctl() only works if the SYS_CAP_RAWIO capability is present
(then queueing happens -- in this example, queue_if_no_path is set);
this is due to a conditional check in scsi_verify_blk_ioctl().
# capsh --drop=cap_sys_rawio -- -c './sgio_inquiry /dev/mapper/85ag56'
sg_simple0: Inquiry SG_IO ioctl error: Inappropriate ioctl for device
# ./sgio_inquiry /dev/mapper/85ag56 &
[1] 72830
# cat /proc/72830/stack
[<c00000171c0df700>] 0xc00000171c0df700
[<c000000000015934>] __switch_to+0x204/0x350
[<c000000000152d4c>] msleep+0x5c/0x80
[<c00000000077dfb0>] dm_blk_ioctl+0x70/0x170
[<c000000000487c40>] blkdev_ioctl+0x2b0/0x9b0
[<c0000000003128e4>] block_ioctl+0x64/0xd0
[<c0000000002dd3b0>] do_vfs_ioctl+0x490/0x780
[<c0000000002dd774>] SyS_ioctl+0xd4/0xf0
[<c000000000009358>] system_call+0x38/0xd0
6) This is the function call chain exercised in this analysis:
SYSCALL_DEFINE3(ioctl, <...>) @ fs/ioctl.c
-> do_vfs_ioctl()
-> vfs_ioctl()
...
error = filp->f_op->unlocked_ioctl(filp, cmd, arg);
...
-> dm_blk_ioctl() @ drivers/md/dm.c
-> multipath_ioctl() @ drivers/md/dm-mpath.c
...
(bdev = NULL, due to no active paths)
...
if (!bdev || <...>) {
int err = scsi_verify_blk_ioctl(NULL, cmd);
if (err)
r = err;
}
...
-> scsi_verify_blk_ioctl() @ block/scsi_ioctl.c
...
if (bd && bd == bd->bd_contains) // not taken (bd = NULL)
return 0;
...
if (capable(CAP_SYS_RAWIO)) // not taken (unprivileged user)
return 0;
...
printk_ratelimited(KERN_WARNING
"%s: sending ioctl %x to a partition!\n" <...>);
return -ENOIOCTLCMD;
<-
...
return r ? : <...>
<-
...
if (error == -ENOIOCTLCMD)
error = -ENOTTY;
out:
return error;
...
Links:
[1] http://git.qemu.org/?p=qemu.git;a=commit;h=336a6915bc7089fb20fea4ba99972ad9a97c5f52
[2] https://libvirt.org/formatdomain.html#elementsDisks (see 'disk' -> 'device')
[3] http://tldp.org/HOWTO/SCSI-Generic-HOWTO/pexample.html (Revision 1.2, 2002-05-03)
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 357ae967ad66e357f78b5cfb5ab6ca07fb4a7758 upstream.
Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit cadd16ea33a938d49aee99edd4758cc76048b399 upstream.
We've had many reports that some Creative sound cards with CA0132
don't work well. Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used. All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.
This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries. I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.
Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too. So
the flag is applied to all Creative entries.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[lizf: Backported to 3.4: drop the change to macro AZX_DCAPS_PRESET_CTHDA]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 49e4b84333f338d4f183f28f1f3c1131b9fb2b5a upstream.
Currently when the system is trying to uninstall the ACPI interrupt
handler, it uses acpi_gbl_FADT.sci_interrupt as the IRQ number.
However, the IRQ number that the ACPI interrupt handled is installed
for comes from acpi_gsi_to_irq() and that is the number that should
be used for the handler removal.
Fix this problem by using the mapped IRQ returned from acpi_gsi_to_irq()
as appropriate.
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 1e6e63283691a2a9048a35d9c6c59cf0abd342e4 upstream.
This adds the USB ID for the Sitecom WLA2100. The Windows 10 inf file
was checked to verify that the addition is correct.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 4327ba52afd03fc4b5afa0ee1d774c9c5b0e85c5 upstream.
If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the
journaling will be aborted first and the error number will be recorded
into JBD2 superblock and, finally, the system will enter into the
panic state in "errors=panic" option. But, in the rare case, this
sequence is little twisted like the below figure and it will happen
that the system enters into panic state, which means the system reset
in mobile environment, before completion of recording an error in the
journal superblock. In this case, e2fsck cannot recognize that the
filesystem failure occurred in the previous run and the corruption
wouldn't be fixed.
Task A Task B
ext4_handle_error()
-> jbd2_journal_abort()
-> __journal_abort_soft()
-> __jbd2_journal_abort_hard()
| -> journal->j_flags |= JBD2_ABORT;
|
| __ext4_abort()
| -> jbd2_journal_abort()
| | -> __journal_abort_soft()
| | -> if (journal->j_flags & JBD2_ABORT)
| | return;
| -> panic()
|
-> jbd2_journal_update_sb_errno()
Tested-by: Hobin Woo <hobin.woo@samsung.com>
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit d14053b3c714178525f22660e6aaf41263d00056 upstream.
The VT-d specification says that "Software must enable ATS on endpoint
devices behind a Root Port only if the Root Port is reported as
supporting ATS transactions."
We walk up the tree to find a Root Port, but for integrated devices we
don't find one — we get to the host bridge. In that case we *should*
allow ATS. Currently we don't, which means that we are incorrectly
failing to use ATS for the integrated graphics. Fix that.
We should never break out of this loop "naturally" with bus==NULL,
since we'll always find bridge==NULL in that case (and now return 1).
So remove the check for (!bridge) after the loop, since it can never
happen. If it did, it would be worthy of a BUG_ON(!bridge). But since
it'll oops anyway in that case, that'll do just as well.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[lizf: Backported to 3.4:
- adjust context
- drop the last part of the changes of the patch]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit e5bae86797141e4a95e42d825f737cb36d7b8c37 upstream.
If we fail to allocate a partition structure in the middle of the partition
creation process, the already allocated partitions are never removed, which
means they are still present in the partition list and their resources are
never freed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 79b568b9d0c7c5d81932f4486d50b38efdd6da6d upstream.
hid_connect adds various strings to the buffer but they're all
conditional. You can find circumstances where nothing would be written
to it but the kernel will still print the supposedly empty buffer with
printk. This leads to corruption on the console/in the logs.
Ensure buf is initialized to an empty string.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
[dvhart: Initialize string to "" rather than assign buf[0] = NULL;]
Cc: Jiri Kosina <jikos@kernel.org>
Cc: linux-input@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 102f4d900c9c8f5ed89ae4746d493fe3ebd7ba64 upstream.
Handle a write being requested to the page immediately beyond the EOF
marker on a cache object. Currently this gets an assertion failure in
CacheFiles because the EOF marker is used there to encode information about
a partial page at the EOF - which could lead to an unknown blank spot in
the file if we extend the file over it.
The problem is actually in fscache where we check the index of the page
being written against store_limit. store_limit is set to the number of
pages that we're allowed to store by fscache_set_store_limit() - which
means it's one more than the index of the last page we're allowed to store.
The problem is that we permit writing to a page with an index _equal_ to
the store limit - when we should reject that case.
Whilst we're at it, change the triggered assertion in CacheFiles to just
return -ENOBUFS instead.
The assertion failure looks something like this:
CacheFiles: Assertion failed
1000 < 7b1 is false
------------[ cut here ]------------
kernel BUG at fs/cachefiles/rdwr.c:962!
...
RIP: 0010:[<ffffffffa02c9e83>] [<ffffffffa02c9e83>] cachefiles_write_page+0x273/0x2d0 [cachefiles]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit b130ed5998e62879a66bad08931a2b5e832da95c upstream.
Only override netfs->primary_index when registering success.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lizf: Backported to 3.4: there are no n_active and flags in primary_index]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 86108c2e34a26e4bec3c6ddb23390bf8cedcf391 upstream.
If netfs exist, fscache should not increase the reference of parent's
usage and n_children, otherwise, never be decreased.
v2: thanks David's suggest,
move increasing reference of parent if success
use kmem_cache_free() freeing primary_index directly
v3: don't move "netfs->primary_index->parent = &fscache_fsdef_index;"
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit d69bbf88c8d0b367cf3e3a052f6daadf630ee566 upstream.
Only cpu seeing dst refcount going to 0 can safely
dereference dst->flags.
Otherwise an other cpu might already have freed the dst.
Fixes: 27b75c95f1 ("net: avoid RCU for NOCACHE dst")
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 40998193560dab6c3ce8d25f4fa58a23e252ef38 upstream.
When dropping a lock while iterating a list we must restart the search
as other threads could have manipulated the list under us. Without this
we can get stuck in an endless loop. This bug was introduced by
commit bc3f02a795
Author: Dan Williams <djbw@fb.com>
Date: Tue Aug 28 22:12:10 2012 -0700
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
Which was itself trying to fix a reported soft lockup issue
http://thread.gmane.org/gmane.linux.kernel/1348679
However, we believe even with this revert of the original patch, the soft
lockup problem has been fixed by
commit f2495e228f
Author: James Bottomley <JBottomley@Parallels.com>
Date: Tue Jan 21 07:01:41 2014 -0800
[SCSI] dual scan thread bug fix
Thanks go to Dan Williams <dan.j.williams@intel.com> for tracking all this
prior history down.
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: bc3f02a795
Signed-off-by: James Bottomley <JBottomley@Odin.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit ebac62fe3d24c0ce22dd83afa7b07d1a2aaef44d upstream.
Both tunnel6_protocol and tunnel46_protocol share the same error
handler, tunnel6_err(), which traverses through tunnel6_handlers list.
For ipip6 tunnels, we need to traverse tunnel46_handlers as we do e.g.
in tunnel46_rcv(). Current code can generate an ICMPv6 error message
with an IPv4 packet embedded in it.
Fixes: 73d605d1ab ("[IPSEC]: changing API of xfrm6_tunnel_register")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit c84da8b9ad3761eef43811181c7e896e9834b26b upstream.
In nop_mcount, shdr->sh_offset and welp->r_offset should handle
endianness properly, otherwise it will trigger Segmentation fault
if the recordmcount main and file.o have different endianness.
Link: http://lkml.kernel.org/r/563806C7.7070606@huawei.com
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 54c09889bff6d99c8733eed4a26c9391b177c88b upstream.
The z2 machine calls pxa27x_set_pwrmode() in order to power off
the machine, but this function gets discarded early at boot because
it is marked __init, as pointed out by kbuild:
WARNING: vmlinux.o(.text+0x145c4): Section mismatch in reference from the function z2_power_off() to the function .init.text:pxa27x_set_pwrmode()
The function z2_power_off() references
the function __init pxa27x_set_pwrmode().
This is often because z2_power_off lacks a __init
annotation or the annotation of pxa27x_set_pwrmode is wrong.
This removes the __init section modifier to fix rebooting and the
build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ba4a90a6d8 ("ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 1f35d04a02a652f14566f875aef3a6f2af4cb77b upstream.
The iomap[] array has PCIM_IOMAP_MAX (6) elements and not
DEVICE_COUNT_RESOURCE (16). This bug was found using a static checker.
It may be that the "if (!(mask & (1 << i)))" check means we never
actually go past the end of the array in real life.
Fixes: ec04b07584 ('iomap: implement pcim_iounmap_regions()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 1f9c6e1bc1ba5f8a10fcd6e99d170954d7c6d382 upstream.
There were several bugs here.
1) The done label was in the wrong place so we didn't copy any
information out when there was no command given.
2) We were using PAGE_SIZE as the size of the buffer instead of
"PAGE_SIZE - pos".
3) snprintf() returns the number of characters that would have been
printed if there were enough space. If there was not enough space
(and we had fixed the memory corruption bug #2) then it would result
in an information leak when we do simple_read_from_buffer(). I've
changed it to use scnprintf() instead.
I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.
Fixes: 5e6e3a92b9 ('wireless: mwifiex: initial commit for Marvell mwifiex driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 90adf98d9530054b8e665ba5a928de4307231d84 upstream.
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.
Fixes: b5874f33bb ("wm831x_power: Use genirq")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>
commit 8ec6d97871f37e4743678ea4a455bd59580aa0f4 upstream.
The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.
Fixes: 615f7b9bb1 ("mac80211: add driver RSSI threshold events")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
