For patent issue need to remove TxStartThresh and RxEarlyThresh. This patent
is cut-through patent. If use this function, Tx will start to transmit after
few data be move in to Tx FIFO. We are not allow to use those function in
DFE530/DFE550/DFE580/DL10050/IP100/IP100A. It will decrease a little
performance.
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the code to change the E8390_CMD register from ei_watchdog().
The 8390-page is always 0 outside the spin_lock.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the new mcp67 device into forcedeth.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support to recover from a previously fatal MAC error. In
the past the MAC would be hung on an internal fatal error. On new
chipsets, the MAC has the ability to enter a non-fatal state and allow
the driver to re-init it.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the mgmt unit in certain chipsets. The MAC
and the mgmt unit share the PHY and therefore proper intialization
procedures are needed for them to maintain coexistense.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PDQ DMA engine requires a different byte-swapping mode for big-endian
hosts; also the MAC address which is read from a register through PIO has
to be byte-swapped. These changes have been verified with DEFPA-DC (PCI)
boards and a Broadcom BCM91250A (MIPS CPU based) host.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
replace open coded kmemdup() to save some screen space,
and allow inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Realtek's 8139/810x (0x8136) PCI-E comes with a touchy PHY.
A big heavy reset seems to calm it down.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7378.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Add a new dynamic itr algorithm, with 2 modes, and make it the default
operation mode. This greatly reduces latency and increases small packet
performance, at the "cost" of some CPU utilization. Bulk traffic
throughput is unaffected.
The driver can limit the amount of interrupts per second that the
adapter will generate for incoming packets. It does this by writing a
value to the adapter that is based on the maximum amount of interrupts
that the adapter will generate per second.
Setting InterruptThrottleRate to a value greater or equal to 100 will
program the adapter to send out a maximum of that many interrupts per
second, even if more packets have come in. This reduces interrupt
load on the system and can lower CPU utilization under heavy load,
but will increase latency as packets are not processed as quickly.
The default behaviour of the driver previously assumed a static
InterruptThrottleRate value of 8000, providing a good fallback value
for all traffic types,but lacking in small packet performance and
latency. The hardware can handle many more small packets per second
however, and for this reason an adaptive interrupt moderation algorithm
was implemented.
Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in
which it dynamically adjusts the InterruptThrottleRate value based on
the traffic that it receives. After determining the type of incoming
traffic in the last timeframe, it will adjust the InterruptThrottleRate
to an appropriate value for that traffic.
The algorithm classifies the incoming traffic every interval into
classes. Once the class is determined, the InterruptThrottleRate
value is adjusted to suit that traffic type the best. There are
three classes defined: "Bulk traffic", for large amounts of packets
of normal size; "Low latency", for small amounts of traffic and/or
a significant percentage of small packets; and "Lowest latency",
for almost completely small packets or minimal traffic.
In dynamic conservative mode, the InterruptThrottleRate value is
set to 4000 for traffic that falls in class "Bulk traffic". If
traffic falls in the "Low latency" or "Lowest latency" class, the
InterruptThrottleRate is increased stepwise to 20000. This default
mode is suitable for most applications.
For situations where low latency is vital such as cluster or
grid computing, the algorithm can reduce latency even more when
InterruptThrottleRate is set to mode 1. In this mode, which operates
the same as mode 3, the InterruptThrottleRate will be increased
stepwise to 70000 for traffic in class "Lowest latency".
Setting InterruptThrottleRate to 0 turns off any interrupt moderation
and may improve small packet latency, but is generally not suitable
for bulk throughput traffic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add a generic MSI interrupt routine that is IO read-free, speeding up
MSI interrupt handling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This file needs some cleanups and reordering - logically order it
so that relevant defines and code are together with properly quoted
defaults.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Spec fix: don't set IDE unless we are actually setting the tx
int delay time.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
ICH8 will soon be followed by newer chipsets bearing the same acronym,
thus we remove the '8' and make it independent of the version number in
the platform name.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add a netif_wake/start_queue counter to the ethtool statistics to indicated
to the user that their transmit ring could be too small for their workload.
Signed-off-by: Jesse brandeburg <jesse.brandeburg@intel.com>
Cc: Jamal Hadi <hadi@cyberus.ca>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add support for a Low Profile quad-port PCI-E adapter and 2 variants
of the ICH8 systems' onboard NIC's.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This memsetting was added in a paranoid rage debugging TX hangs, but
are no longer of importance. We can beef up the performance quite a
bit removing them. Make sure to fill in next_to_watch to allow this.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Order pci-e capability struct according to bus/pci bus width ordering
preserving the hard pci spec numbers.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On ich systems during PHY power down to D3, the voltage regulators
were left on.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IA64 SMP systems were seeing TX issues with multiple cpu's attempting
to write tail registers unordered. This mmiowb() fixes the issue.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Enable early receives on 82573 for jumbo frame performance. Jumbo's
are only supported on 82573L with ASPM disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Enable TSO for IPV6. All e1000 hardware supports it. This reduces CPU
utilizations by 50% when transmitting IPv6 frames.
Fix symbol naming enabling ipv6 TSO. Turn off TSO6 for 10/100.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove debugging code disabling MULR (multiple reads). It's not usable
for a wide audience and there are no known problems with MULR right
now.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Tested by Newsome on IRC
zd1211 chip 0586:3401 v4330 high 00-13-49 AL2230_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bcm43xx driver does not contain code to handle PCI-E interfaces
such as the BCM4311 and BCM4312. This patch, originally written by Stefano
Brivio adds the necessary code to enable these interfaces.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Output signal strength information as part of iwlist scan - before it did
not output any signal strength related information.
Signed-off-by: Holden Karau <holden@pigscanfly.ca>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NET: prism54 - fix potential race in reset scheduling
There appears to be a race in reset scheduling logic - thread
responsible for reseting the interface should clear "reset
pending" flag before restarting the queue, otherwise timeout
handler might not schedule another reset even if it is needed.
This race is mostly theoretical as far as I can see but a race
nonetheless.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NET: atmel - do not initialize array over and over again
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a host_strip_iv_icv flag to ieee80211 which indicates that
ieee80211_rx should strip the IV/ICV/other security features from the payload.
This saves on some memmove() calls in the driver and seems like something that
belongs in the stack as it can be used by bcm43xx, ipw2200, and zd1211rw
I will submit the ipw2200 patch separately as it needs testing.
This patch also adds some sensible variable reuse (idx vs keyidx) in
ieee80211_rx
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bcm43xx-softmac driver fails to set two quantities needed for
iwlist to compute wireless quality when scanning. As a result, userland
programs using the quality to determine the best connection fail.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rest of 8390 conversions; ifdef cascade in 8390.h is gone now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
more 8390 conversions - mac8390, zorro8390 and hydra got the same treatment
as arm etherh; one more case in 8390.h ifdef cascade is gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
etherh and a handful of other odd drivers use different macros when building
8390.c. Since we generate a single 8390.o and then link with it, in any
config with both oddball and normal 8390-based driver we will end up with
breakage in at least one of them. Solution: take most of 8390.c into
lib8390.c and have 8390.c, etherh.c and the rest of oddballs #include it.
Helper macros are taken from 8390.h to whoever includes lib8390.c. That
way odd drivers get separate instances of compiled 8390 stuff and stop
stepping on each other's toes. 8390.h gets cleaned up - we don't have
the cascade of ifdefs in there and are left with the stuff that can be
used by any 8390-based driver. Current problems are exactly because of
that cascade - we attempt to choose the set of helpers by looking at config
and that, of course, doesn't work well when we have several sets needed
by various drivers in our config.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add MII ioctl support to the deprecated sk98lin driver.
This allows comparison with skge driver's PHY settings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for dumping the registers in the deprecated
sk98lin driver. This is allows for easier comparison with
settings in new skge driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_module_init() convertion in olympic.c
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was spotted by coverity (cid #793). All callers dereference dev
before calling this functions, and we dereference it earlier in the
function, when initializing lp.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tobias Diedrich <ranma@tdiedrich.de> sayeth:
Vanilla forcedeth doesn't seem to support suspend and an ifdown/up-cycle is
needed to get it working again after suspend. Francois Romieu's "Awfully
experimental" patch is working just fine for me (with message signalled
interrupts disabled) and has survived quite a few suspend/resume cycles.
So I'd very much like to see (at least partial, with msi disabled)
suspend support for forcedeth in mainline.
(Addresses http://bugzilla.kernel.org/show_bug.cgi?id=6398)
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc; Jeff Garzik <jeff@garzik.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a couple of problems discovered with interrupt handling
in the phylib core, namely:
1. The driver uses timer and workqueue calls, but does not include
<linux/timer.h> nor <linux/workqueue.h>.
2. The driver uses schedule_work() for handling interrupts, but does not
make sure any pending work scheduled thus has been completed before
driver's structures get freed from memory. This is especially
important as interrupts may keep arriving if the line is shared with
another PHY.
The solution is to ignore phy_interrupt() calls if the reported device
has already been halted and calling flush_scheduled_work() from
phy_stop_interrupts() (but guarded with current_is_keventd() in case
the function has been called through keventd from the MAC device's
close call to avoid a deadlock on the netlink lock).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
patch-mips-2.6.18-20060920-phy-irq-16
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for interrupt-driven operation of the Broadcom
Gigabit Ethernet PHYs. I have included device IDs for the parts used on
Broadcom SiByte evaluation boards; more can be added as a need arises.
They are apparently generally software-compatible with one another.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
patch-mips-2.6.18-20060920-broadcom-phy-15
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Fix an offset error when reading the CS89x0 ADD_PORT register
[PATCH] spidernet: poor network performance
[PATCH] Spidernet: remove ETH_ZLEN check in earlier patch
[PATCH] bonding: fix an oops when slave device does not provide get_stats
[PATCH] drivers/net: SAA9730: Fix build error
Revert "[PATCH] zd1211rw: Removed unneeded packed attributes"
[PATCH] zd1211rw: Fix of a locking bug
[PATCH] softmac: remove netif_tx_disable when scanning
[PATCH] ieee80211: Fix kernel panic when QoS is enabled
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
usbcore: remove unused argument in autosuspend
USB: keep count of unsuspended children
USB hub: simplify remote-wakeup handling
USB: struct usb_device: change flag to bitflag
OHCI: make autostop conditional on CONFIG_PM
USB: Add autosuspend support to the hub driver
EHCI: Fix root-hub and port suspend/resume problems
USB: create a new thread for every USB device found during the probe sequence
USB: add driver for the USB debug devices
USB: added dynamic major number for USB endpoints
USB: pegasus error path not resetting task's state
USB: endianness fix for asix.c
USB: build the appledisplay driver
USB serial: replace kmalloc+memset with kzalloc
USB: hid-core: canonical defines for Apple USB device IDs
USB: idmouse cleanup
USB: make drivers/usb/core/driver.c:usb_device_match() static
USB: lh7a40x_udc remove double declaration
USB: pxa2xx_udc recognizes ixp425 rev b0 chip
usbtouchscreen: add support for DMC TSC-10/25 devices
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
Driver core: show drivers in /sys/module/
Documentation/driver-model/platform.txt update/rewrite
Driver core: platform_driver_probe(), can save codespace
driver core: Use klist_remove() in device_move()
driver core: Introduce device_move(): move a device to a new parent.
Driver core: make drivers/base/core.c:setup_parent() static
driver core: Introduce device_find_child().
sysfs: sysfs_write_file() writes zero terminated data
cpu topology: consider sysfs_create_group return value
Driver core: Call platform_notify_remove later
ACPI: Change ACPI to use dev_archdata instead of firmware_data
Driver core: add dev_archdata to struct device
Driver core: convert sound core to use struct device
Driver core: change mem class_devices to be real devices
Driver core: convert fb code to use struct device
Driver core: convert firmware code to use struct device
Driver core: convert mmc code to use struct device
Driver core: convert ppdev code to use struct device
Driver core: convert PPP code to use struct device
Driver core: convert cpuid code to use struct device
...
This defines a new platform_driver_probe() method allowing the driver's
probe() method, and its support code+data, to safely live in __init
sections for typical system configurations.
Many system-on-chip processors could benefit from this API, to the tune
of recovering hundreds to thousands of bytes per driver. That's memory
which is currently wasted holding code which can never be called after
system startup, yet can not be removed. It can't be removed because of
the linkage requirement that pointers to init section code (like, ideally,
probe support) must not live in other sections (like driver method tables)
after those pointers would be invalid.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As pointed out by Alan Stern, device_move needs to use klist_remove which waits
until removal is complete.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide a function device_move() to move a device to a new parent device. Add
auxilliary functions kobject_move() and sysfs_move_dir().
kobject_move() generates a new uevent of type KOBJ_MOVE, containing the
previous path (DEVPATH_OLD) in addition to the usual values. For this, a new
interface kobject_uevent_env() is created that allows to add further
environmental data to the uevent at the kobject layer.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global setup_parent() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Take return value of sysfs_create_group() into account. That function got
called in case of CPU_ONLINE notification. Since callbacks are not allowed
to fail on CPU_ONLINE notification do the sysfs group creation on
CPU_UP_PREPARE notification.
Also remember if creation succeeded in a bitmask. So it's possible to know
whether it's legal to call sysfs_remove_group or not.
In addition some other minor stuff:
- since CPU_UP_PREPARE might fail add CPU_UP_CANCELED handling as well.
- use hotcpu_notifier instead of register_hotcpu_notifier.
- #ifdef code that isn't needed in the !CONFIG_HOTPLUG_CPU case.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the call to platform_notify_remove() to after the call to
bus_remove_device(), where it belongs. It's bogus to notify the platform
of removal while drivers are still attached to the device and possibly
still operating since the platform might use this callback to tear down
some resources used by the driver (ACPI bits, iommu table, ...)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change ACPI to use dev_archdata instead of firmware_data
This patch changes ACPI to use the new dev_archdata on i386, x86_64
and ia64 (is there any other arch using ACPI ?) to store it's
acpi_handle.
It also removes the firmware_data field from struct device as this
was the only user.
Only build-tested on x86
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Also fixes up the isdn drivers that were putting something in the class
device's directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also ment that some of the misc drivers had to also be fixed
up as they were assuming the device was a class_device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Turn off class symlinks CONFIG_SYSFS_DEPRECATED is enabled.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable the PHYSDEV* uevent variables if CONFIG_SYSFS_DEPRECATED is
enabled.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Turn off device symlinks CONFIG_SYSFS_DEPRECATED is enabled.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Turn off the bus symlinks if CONFIG_SYSFS_DEPRECATED is enabled
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If CONFIG_SYSFS_DEPRECATED is enabled, old versions of udev will work
properly with devices that are associated with a class.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Create the "driver" link before the child device may be created by
the probing logic. This makes it possible for userspace (udev), to
determine the driver property of the parent device, at the time the
child device is created.
Signed-off-by: Kay Sievers <kay.sievers@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I finally did as you suggested and added the notifier to the struct
bus_type itself. There are still problems to be expected is something
attaches to a bus type where the code can hook in different struct
device sub-classes (which is imho a big bogosity but I won't even try to
argue that case now) but it will solve nicely a number of issues I've
had so far.
That also means that clients interested in registering for such
notifications have to do it before devices are added and after bus types
are registered. Fortunately, most bus types that matter for the various
usage scenarios I have in mind are registerd at postcore_initcall time,
which means I have a really nice spot at arch_initcall time to add my
notifiers.
There are 4 notifications provided. Device being added (before hooked to
the bus) and removed (failure of previous case or after being unhooked
from the bus), along with driver being bound to a device and about to be
unbound.
The usage I have for these are:
- The 2 first ones are used to maintain a struct device_ext that is
hooked to struct device.firmware_data. This structure contains for now a
pointer to the Open Firmware node related to the device (if any), the
NUMA node ID (for quick access to it) and the DMA operations pointers &
iommu table instance for DMA to/from this device. For bus types I own
(like IBM VIO or EBUS), I just maintain that structure directly from the
bus code when creating the devices. But for bus types managed by generic
code like PCI or platform (actually, of_platform which is a variation of
platform linked to Open Firmware device-tree), I need this notifier.
- The other two ones have a completely different usage scenario. I have
cases where multiple devices and their drivers depend on each other. For
example, the IBM EMAC network driver needs to attach to a MAL DMA engine
which is a separate device, and a PHY interface which is also a separate
device. They are all of_platform_device's (well, about to be with my
upcoming patches) but there is no say in what precise order the core
will "probe" them and instanciate the various modules. The solution I
found for that is to have the drivers for emac to use multithread_probe,
and wait for a driver to be bound to the target MAL and PHY control
devices (the device-tree contains reference to the MAL and PHY interface
nodes, which I can then match to of_platform_devices). Right now, I've
been polling, but with that notifier, I can more cleanly wait (with a
timeout of course).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The correct order is: NULL check before dereference
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that "irq XX: nobody cared" kernel oops
is reported when pciehp is once rmmoded and insmoded again. The cause
of this problem is pciehp driver calls pci_disable_msi() at controller
release time, even though it must be done by PCI Express Port Bus
driver. This patch removes unnecessary pci_disable_msi() call from
pciehp driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that the following error messages is
reported when pciehp driver is rmmoded.
Trying to free already-free IRQ XX
The cause of this problem is that pciehp driver is doing unknown 2nd
free_irq at driver unloading. This patch removes this unknown 2nd
free_irq call.
Note: The pciehp driver should be adapted to standard device driver
mode.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the criterion that RPA PCI Hotplug and RPA DLPAR use when
determining the hotplug capabilities of a given device node. The
"device_type" property is less consistent than "name" across PCI nodes
on newer hardware.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change memory allocation for acpiphp slots
Change the "struct slot" that acpiphp uses for managing it's slots to
directly contain the memory for the needed struct hotplug_slot_info and
the slot's name. This way we need only two memory allocations per slot
instead of four.
While we are at it: make_slot_name() is just a wrapper around snprintf()
knowing the right arguments to call it. Since the function makes just one
function call and is only called from one place I inlined it by hand.
Finally this fixes a possible bug waiting for someone to hit it. There were
two unused local variables in acpiphp_register_hotplug_slot(). gcc did not
find them because they were used in memory allocations with sizeof(*var).
They had the same types as the target of the allocation, but nevertheless
this was just weird.
Signed-off-by: Rolf Eike Beer <eike-hotplug@sf-tec.de>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updated patch adds the Intel ICH9 LPC and SMBus Controller DID's. Thi=
s patch relies on the irq ICH9 patch to pci_ids.h.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change drivers/message/i20 pci driver to simply do a nestable
enable()/disable() instead of checking for it.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes the pci_{enable,disable}_device() functions to work in a
nested basis, so that eg, three calls to enable_device() require three
calls to disable_device().
The reason for this is to simplify PCI drivers for
multi-interface/capability devices. These are devices that cram more
than one interface in a single function. A relevant example of that is
the Wireless [USB] Host Controller Interface (similar to EHCI) [see
http://www.intel.com/technology/comms/wusb/whci.htm].
In these kind of devices, multiple interfaces are accessed through a
single bar and IRQ line. For that, the drivers map only the smallest
area of the bar to access their register banks and use shared IRQ
handlers.
However, because the order at which those drivers load cannot be known
ahead of time, the sequence in which the calls to pci_enable_device()
and pci_disable_device() cannot be predicted. Thus:
1. driverA starts pci_enable_device()
2. driverB starts pci_enable_device()
3. driverA shutdown pci_disable_device()
4. driverB shutdown pci_disable_device()
between steps 3 and 4, driver B would loose access to it's device,
even if it didn't intend to.
By using this modification, the device won't be disabled until all the
callers to enable() have called disable().
This is implemented by replacing 'struct pci_dev->is_enabled' from a
bitfield to an atomic use count. Each caller to enable increments it,
each caller to disable decrements it. When the count increments from 0
to 1, __pci_enable_device() is called to actually enable the
device. When it drops to zero, pci_disable_device() actually does the
disabling.
We keep the backend __pci_enable_device() for pci_default_resume() to
use and also change the sysfs method implementation, so that userspace
enabling/disabling the device doesn't disable it one time too much.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The existing implementation of pci_block_user_cfg_access() was recently
criticised for providing out of date information and for returning errors
on write, which applications won't be expecting.
This reimplementation uses a global wait queue and a bit per device.
I've open-coded prepare_to_wait() / finish_wait() as I could optimise
it significantly by knowing that the pci_lock protected us at all points.
It looked a bit funny to be doing a spin_unlock_irqsave(); schedule(),
so I used spin_lock_irq() for the _user versions of pci_read_config and
pci_write_config. Not carrying a flags pointer around made the code
much less nasty.
Attempts to block an already blocked device hit a BUG() and attempts to
unblock an already unblocked device hit a WARN(). If we need to block
access to a device from userspace, it's because it's unsafe for even
another bit of the kernel to access the device. An attempt to block
a device for a second time means we're about to access the device to
perform some other operation, which could provoke undefined behaviour
from the device.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Adam Belay <abelay@novell.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__pci_register_driver() error path forgot to unwind.
driver_unregister() needs to be called when pci_create_newid_file() failed.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So it looks like pci aer code will call pci_osc_support_set to tell the
firmware about OSC_EXT_PCI_CONFIG_SUPPORT flag. that causes
ctrlset_buf[OSC_SUPPORT_TYPE] to evaluate to true when pciehp calls
pci_osc_control_set() is called (to attempt to use OSC to gain native
pcie control from firmware), regardless of whether or not _OSC was
actually successfully executed. That causes this section of code:
if (ctrlset_buf[OSC_SUPPORT_TYPE] &&
((global_ctrlsets & ctrlset) != ctrlset)) {
return AE_SUPPORT;
}
to be hit.
This patch will reset the OSC_SUPPORT_TYPE field if _OSC fails, and then
would allow pciehp to go ahead and try to run _OSC again.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpiphp_glue_exit() needs to be called to unwind when no slots found.
(It fixes data corruption when reloading acpiphp driver with no such devices)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes invalid usage of list_for_each()
list_for_each (node, &bridge_list) {
bridge = (struct acpiphp_bridge *)node;
...
}
This code works while the member of list node is located at the
head of struct acpiphp_bridge.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support a shadowed ROM when running with an ACPI capable PROM.
Define a new dev.resource flag IORESOURCE_ROM_BIOS_COPY to
describe the case of a BIOS shadowed ROM, which can then
be used to avoid pci_map_rom() making an unneeded call to
pci_enable_rom().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A few minor changes to the way slot/device fixup is done.
No need to be calling sn_pci_controller_fixup(), as
a root bus cannot be hotplugged.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pSeries is the only architecture left using HAVE_ARCH_PCI_MWI and it's
really inappropriate for its needs. It really wants to disable MWI
altogether. So here are a pair of stub implementations for pci_set_mwi
and pci_clear_mwi.
Also rename pci_generic_prep_mwi to pci_set_cacheline_size since that
better reflects what it does.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The setting of the CACHE_LINE_SIZE register in sparc64's pci
initialisation code isn't quite adequate as the device may have
incompatible requirements. The generic code tests for this, so switch
sparc64 over to using it.
Since sparc64 has different L1 cache line size and PCI cache line size,
it would need to override the generic code like i386 and ia64 do. We
know what the cache line size is at compile time though, so introduce a
new optional constant PCI_CACHE_LINE_BYTES.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number of permutations of crap we do is amazing and almost all of it
has the wrong effect in 2.6.
At the heart of this is the PCI SFF magic which says that compatibility
mode PCI IDE controllers use ISA IRQ routing and hard coded addresses
not the BAR values. The old quirks variously clears them, sets them,
adjusts them and then IDE ignores the result.
In order to drive all this garbage out and to do it portably we need to
handle the SFF rules directly and properly. Because we know the device
BAR 0-3 are not used in compatibility mode we load them with the values
that are implied (and indeed which many controllers actually
thoughtfully put there in this mode anyway).
This removes special cases in the IDE layer and libata which now knows
that bar 0/1/2/3 always contain the correct address. It means our
resource allocation map is accurate from boot, not "mostly accurate"
after ide is loaded, and it shoots lots of code. There is also lots more
code and magic constant knowledge to shoot once this is in and settled.
Been in my test tree for a while both with drivers/ide and with libata.
Wants some -mm shakedown in case I've missed something dumb or there are
corner cases lurking.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Shouldn't PCI-X state be saved/restored? No device really needs this
right now. qla24xx (fc HBA) and mthca (infiniband) don't do suspend,
and sky2 resets its tweaks when links are brought up.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move some MSI-X #defines into pci_regs.h so they can be used
outside of drivers/pci.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not really broken, but people keep running into other problems
caused by it. Re-enable it so that the drivers get stress tested.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to several earlier patches, usb_autosuspend_device() and
usb_autoresume_device() are never called with a second argument other
than 1. This patch (as819) removes the now-redundant argument.
It also consolidates some common code between those two routines,
putting it into a new subroutine called usb_autopm_do_device(). And
it includes a sizable kerneldoc update for the affected functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as818b) simplifies autosuspend processing by keeping track
of the number of unsuspended children of each USB hub. This will
permit us to avoid a good deal of unnecessary work all the time; we
will no longer have to create a bunch of workqueue entries to carry
out autosuspend requests, only to have them fail because one of the
hub's children isn't suspended.
The basic idea is simple. There already is a usage counter in the
usb_device structure for preventing autosuspends. The patch just
increments that counter for every unsuspended child. There's only one
tricky part: When a device disconnects we need to remember whether it
was suspended at the time (leave the counter alone) or not (decrement
the counter).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as817) simplifies the remote-wakeup processing in the hub
driver. Now instead of using a specialized code path, it relies on
the standard USB resume routines. The hub_port_resume() function does
an initial get_port_status() to see whether the port has already
resumed itself (as it does when a remote-wakeup request is sent).
This will slow down handling of other resume events slightly, but not
enough to matter.
The patch also changes the hub_port_status() routine, making it return
an error if a short reply is received.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as816) changes an existing flag in the usb_device
structure to a bitflag, preparing the way for more bitflags to come
in the future.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unlike UHCI, OHCI does not exert any DMA load on the system when no
devices are connected. Consequently there is no advantage to doing
an autostop other than the power savings, so we shouldn't compile the
necessary code unless CONFIG_PM is enabled.
This patch (as820) makes the root-hub suspend and resume routines
conditional on CONFIG_PM. It also prevents autostop from activating
if the device_may_wakeup flag isn't set; some people use this flag to
alert the driver about Resume-Detect bugs in the hardware.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as742b) adds autosuspend/autoresume support to the USB hub
driver. The largest aspect of the change is that we no longer need a
special flag for root hubs that want to be resumed. Now every hub is
autoresumed whenever khubd needs to access it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:
The bus_resume() routine should wake up only the ports that
were suspended by bus_suspend(). Ports that were already
suspended should remain that way.
The interrupt mask is used to detect loss of power in the
bus_resume() routine (if the mask is 0 then power was lost).
However bus_suspend() always sets the mask to 0. Instead the
mask should retain its normal value, with port-change-detect
interrupts disabled if remote wakeup is turned off.
The interrupt mask should be reset to its correct value at the
end of bus_resume() regardless of whether power was lost.
bus_resume() reinitializes the operational registers if power
was lost. However those registers are not in the aux power
well, hence they can lose their values whenever the controller
is put into D3. They should always be reinitialized.
When a port-change interrupt occurs and the root hub is
suspended, the interrupt handler should request a root-hub
resume instead of starting up the controller all by itself.
There's no need for the interrupt handler to request a
root-hub resume every time a suspended port sends a
remote-wakeup request.
The pci_resume() method doesn't need to check for connected
ports when deciding whether or not to reset the controller.
It can make that decision based on whether Vaux power was
maintained.
Even when the controller does not need to be reset,
pci_resume() must undo the effect of pci_suspend() by
re-enabling the interrupt mask.
If power was lost, pci_resume() must not call ehci_run().
At this point the root hub is still supposed to be suspended,
not running. It's enough to rewrite the command register and
set the configured_flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Might speed up some systems. If nothing else, a bad driver should not
take the whole USB subsystem down with it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is an update for Greg K-H's proposed usbfs2:
http://sourceforge.net/mailarchive/message.php?msg_id=19295229
It creates a dynamic major for USB endpoints and fixes
the endpoint minor calculation.
Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there is an error path in the pegasus driver which can leave
the task in TASK_UNINTERRUPTIBLE. Depending on when it
schedules next, this can be bad.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the latest update for asix.c reverted some endianness fixes. This
reinstates them.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do already have both the code and a config option, so why not build
this driver? ;-)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use canonical defines for the Apple USB device IDs.
Also add the Geyser IV devices missing in my previous patch.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Acked-by: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just digging through code and found these needless variable initializations. So here is the patch.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the pxa2xx_udc driver recognize a newer revision of the IXP425 chip.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the DMC TSC-10 and TSC-25 usb touchscreen controllers.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following possible cleanups:
- make the needlessly global ftdi_release_platform_dev() static
- remove the unused usb_ftdi_elan_read_reg()
- proper prototypes for the following functions:
- usb_ftdi_elan_read_pcimem()
- usb_ftdi_elan_write_pcimem()
Note that the misplaced prototypes for the latter ones in
drivers/usb/host/u132-hcd.c were buggy. Depending on the calling
convention of the architecture calling one of them could have turned
your stack into garbage.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global "u132_hcd_wait" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If at some point cypress_init() fails deregister
only the resources that were registered until that point.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them. This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators). This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).
Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog). The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.
Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI hooks for high speed electrical tests of the root hub ports.
The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The net2280 driver is too eager to send zero-length packets when
IN tokens are received on ep0. No such packet should be sent (the
driver should NAK) before the gadget driver has queued the proper
response. Otherwise deferred responses are impossible.
This patch (as823) makes net2280 avoid sending ZLPs for IN transfers
on ep0 until a response has been submitted, and avoids stalling when an
OUT packet is received before a request has been submitted for an OUT
transfer on ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Possible memleak fix on error path. The changes:
- out_kfree2 and out_free_urb replaced
- missing scsi_host_put() added
Here it goes:
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297. This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).
T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1210 ProdID=0003 Rev= 1.00
S: Manufacturer=DigiTech HMG
S: Product=DigiTech Mass Storage
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Signed-off-by: Jaco Kroon <jaco@kroon.co.za>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as821) fixes a compiler warning when CONFIG_PM isn't on
("usb_autosuspend_work" defined but not used).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> 2006/11/11, Adrian Bunk <bunk@stusta.de>:
> > The Coverity checker spotted the following in
> > drivers/usb/serial/aircable.c:
> >
> > <-- snip -->
> >
> > ...
> > static void aircable_read(void *params)
> > {
> > ...
Hi everyone,
Sorry for the long time response but here is the patch, I think this way should
work, if anyone has any suggestion let me know. What I do now is, in case I
don't have the tty available I reschedule the work, I have tried it and it
works with no problem, I even tried removing the device, and didn't find
anything strange.
Signed-off-by: Naranjo Manuel <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the other root-hub suspend or resume log messages, in ohci-hcd or
any of the other host controller drivers, use the debug priority
level. This patch (as815) makes the one single exception behave like
all the rest.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
