This is changing "always true" test to something usefull.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch makes the needlessly global longhaul_walk_callback() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
It seems commit 32ee8c3e47 accidentially
reverted cdc9cc1d74, IOW, it reintroduced
the following compile error with CONFIG_PCI=n:
<-- snip -->
...
CC arch/i386/kernel/cpu/cpufreq/gx-suspmod.o
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c: In function ‘gx_detect_chipset’:
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: error: implicit declaration of function ‘pci_match_id’
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: warning: comparison between pointer and integer
make[3]: *** [arch/i386/kernel/cpu/cpufreq/gx-suspmod.o] Error 1
<-- snip -->
This patch therefore re-adds the dependency of X86_GX_SUSPMOD on PCI.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Without this longhaul will always fail when compiled into kernel,
as it needs to initialise after the ACPI processor module.
I lost this when I was splitting patches. Sorry.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
There is no need to worry about local APIC.
There is need to worry about I/O APIC, because I/O APIC
is replacing good old 8259. According to Nehemiah datasheet VIA is
using 3-wire bus to connect local APIC to I/O APIC.
"[...] When IA32_APIC_BASE[11] is set to 0, processor APICs based on the 3-wire APIC
bus cannot be generally re-enabled until a system hardware reset. The 3-wire bus
looses track of arbitration that would be necessary for complete re-enabling. Certain
(local) APIC functionality can be enabled. [...]"
So we must set disable bit for each interrupt in I/O APIC registers.
Same situation as for PIC - we must poke registers direcly.
How to do this? I don't know. So at the moment it is better to fail.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Minimal change necessary for hardware support.
Changes in longhaul.c:
- most important - now C3 state is causing transition,
- code responsible for clearing "bus master" bit removed,
- protect bcr2 transition in the same way as longhaul.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Use hotplug version of register_cpu_notifier in late init functions.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mce_disabled cannot be __initdata - we access it during APM resume.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 1e9f28fa1e ("[PATCH] sched: new
sched domain for representing multi-core") incorrectly made SCHED_SMT
and some of the structures it uses dependent on SMP.
However, this is wrong, the structures are only defined if X86_HT, so
SCHED_SMT has to depend on that as well.
The patch broke voyager, since it doesn't provide any of the multi-core
or hyperthreading structures.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the phys_core_id and cpu_core_id to cpuinfo_x86 structure. Similar
patch for x86_64 is already accepted by Andi earlier this week.
[akpm@osdl.org: fix warning]
Signed-off-by: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch fixes two issues:
1. cpu_init is called with interrupt disabled. Allocating gdt table
there isn't good at runtime.
2. gdt table page cause memory leak in CPU hotplug case.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
Intel now has support for Architectural Performance Monitoring Counters
( Refer to IA-32 Intel Architecture Software Developer's Manual
http://www.intel.com/design/pentium4/manuals/253669.htm ). This
feature is present starting from Intel Core Duo and Intel Core Solo processors.
What this means is, the performance monitoring counters and some performance
monitoring events are now defined in an architectural way (using cpuid).
And there will be no need to check for family/model etc for these architectural
events.
Below is the patch to use this performance counters in nmi watchdog driver.
Patch handles both i386 and x86-64 kernels.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Intel systems report the cache level data from CPUID 4 in sysfs.
Add a CPUID 4 emulation for AMD CPUs to report the same
information for them. This allows programs to read this
information in a uniform way.
The AMD way to report this is less flexible so some assumptions
are hardcoded (e.g. no L3)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previously the apicid<->coreid split was computed based on the max
number of cores. Now use a new CPUID AMD defined for that. On most
systems right now it should be 0 and the old method will be used.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Treat HW coordination as independent CPUs.
This enables per-cpu monintoring of P-states
http://bugzilla.kernel.org/show_bug.cgi?id=5737
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Convert a few stragglers over to for_each_possible_cpu(), remove
for_each_cpu().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
New CPU flags for next generation of crypto engine as found in VIA C7
processors.
Signed-off-by: Michal Ludvig <michal@logix.cz>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI code was outside of CONFIG_PCI, add __initdata at cyrix_55x0 (since
accessed within __init function only).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only drm, framebuffer, mtrr parts + misc files here and there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I haven't really maintained this driver for a while, and I'm not
keeping up with the latest in Intel power management. I get a steady
stream of mail which I don't really do anything useful with; the
cpufreq list seems like a better destination, unless someone wants to
get the mail directly.
Also clean up a couple of ancient comments which don't really apply
anymore (as far as I know, nobody has ever damaged a CPU with this
driver).
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The fid/vid masks for parts using the extended parts are slightly incorrect and can result in
incorrect fid/vid codes being applied. No instances of this problem have been reported in
the field but it could be a problem with future parts.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch clarifies the meaning of the cpu_family if
statements in the hw pstate driver patch for powernow-k8
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Sets minimum PLL divider to 2.
No negative impact when tested with two nForce2 based boards.
Alexander Choporov reported (06/01/06) that xdiv = 1 does not work on his
Abit NF7S2. Although there shouldn't be much cases that lead to xdiv = 1.
(Updates also the (C) year)
Signed-off-by: Sebastian Witt <se.witt@gmx.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Even though powernow-k7 doesn't work in SMP environments,
it can work on an SMP configured kernel if there's only
one CPU present, however recalibrate_cpu_khz was returning
-EINVAL on such kernels, so we failed to init the cpufreq driver.
Signed-off-by: Dave Jones <davej@redhat.com>
Remove KERN_* suffixes from some Centrino cpufreq driver's dprintk-s.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove KERN_* suffixes from some NForce2 cpufreq driver's dprintk-s.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Forthcoming AMD products will use a different algorithm for transitioning
pstates than the current generation Opteron products do. The attached
patch allows the powernow-k8 driver to work with those products.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This prevents annoying messages being printed when it gets
loaded on a machine that doesn't have support scaling via ACPI.
Signed-off-by: Dave Jones <davej@redhat.com>
This shouldn't have actually caused any problems
(as we return if we 'corrupt' 'i', but it's still not
very pretty. For the sake of adding another local variable,
this got cleaner.
Signed-off-by: Dave Jones <davej@redhat.com>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD K7/K8 CPUs only save/restore the FOP/FIP/FDP x87 registers in FXSAVE
when an exception is pending. This means the value leak through
context switches and allow processes to observe some x87 instruction
state of other processes.
This was actually documented by AMD, but nobody recognized it as
being different from Intel before.
The fix first adds an optimization: instead of unconditionally
calling FNCLEX after each FXSAVE test if ES is pending and skip
it when not needed. Then do a x87 load from a kernel variable to
clear FOP/FIP/FDP.
This means other processes always will only see a constant value
defined by the kernel in their FP state.
I took some pain to make sure to chose a variable that's already
in L1 during context switch to make the overhead of this low.
Also alternative() is used to patch away the new code on CPUs
who don't need it.
Patch for both i386/x86-64.
The problem was discovered originally by Jan Beulich. Richard
Brunner provided the basic code for the workarounds, with contribution
from Jan.
This is CVE-2006-1056
Cc: richard.brunner@amd.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a check-after-use introduced by commit
4211a30349 and spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove a duplicate NULL pointer check introduced by commit
4211a30349
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Dave Jones <davej@redhat.com>
It's not actually needed and would break non power of two number
of cores.
Follows similar earlier x86-64 patch.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This prevents crashes on dual core system when enough ticks are lost.
Replaces earlier patch by me.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpu_online_map doesn't exist if !CONFIG_SMP.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi's previous fix to initialise powernow_data on all siblings
will not work properly with CPU Hotplug.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Don't use cpuid.2 to determine cache info if cpuid.4 is supported. The
exception is P4 trace cache. We always use cpuid.2 to get trace cache
under P4.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new sched domain for representing multi-core with shared caches
between cores. Consider a dual package system, each package containing two
cores and with last level cache shared between cores with in a package. If
there are two runnable processes, with this appended patch those two
processes will be scheduled on different packages.
On such systems, with this patch we have observed 8% perf improvement with
specJBB(2 warehouse) benchmark and 35% improvement with CFP2000 rate(with 2
users).
This new domain will come into play only on multi-core systems with shared
caches. On other systems, this sched domain will be removed by domain
degeneration code. This new domain can be also used for implementing power
savings policy (see OLS 2005 CMP kernel scheduler paper for more details..
I will post another patch for power savings policy soon)
Most of the arch/* file changes are for cpu_coregroup_map() implementation.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I got an oops on a dual core system because the lost tick handler
called cpufreq_get() on core 1 and powernow tried to follow
a NULL powernow_data[] pointer there.
Initialize powernow_data for all cores of a CPU.
Cc: Jacob Shin <jacob.shin@amd.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug identified by Linus Torvalds <torvalds@osdl.org>: the `out'
instruction depends upon the state of memory_data[], so we need to tell gcc
that before executing it. (The opcode, not gcc).
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5553
Thanks to Antonio Ospite <ospite@studenti.unina.it> for testing.
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I screwed up this conversion - we should be iterating across online CPUs, not
possible ones.
Spotted by Joe Perches <joe@perches.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/i386/kernel/cpu/centaur.c: In function `centaur_mcr_insert':
arch/i386/kernel/cpu/centaur.c:33: warning: implicit declaration of function `mtrr_centaur_report_mcr'
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When vendor-specific i386 initialization code is unavailable the kernel
falls back to a default CPU model name. Make that model name reflect the
CPU family instead of an internal vendor index.
Tested on Pentium II (family 6 model 5).
/proc/cpuinfo before:
model name : ff/05
after:
model name : 06/05
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the x86 "sep" feature to be disabled at bootup. This forces use of the
int80 vsyscall. Mainly for testing or benchmarking the int80 vsyscall code.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several places in arch/i386/kernel/cpu and kernel/cpu were using __devinit
when they should have been __cpuinit. Fixing that saves ~4K when
CONFIG_HOTPLUG && !CONFIG_HOTPLUG_CPU.
Noticed by Andrew Morton.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement SMP alternatives, i.e. switching at runtime between different
code versions for UP and SMP. The code can patch both SMP->UP and UP->SMP.
The UP->SMP case is useful for CPU hotplug.
With CONFIG_CPU_HOTPLUG enabled the code switches to UP at boot time and
when the number of CPUs goes down to 1, and switches to SMP when the number
of CPUs goes up to 2.
Without CONFIG_CPU_HOTPLUG or on non-SMP-capable systems the code is
patched once at boot time (if needed) and the tables are released
afterwards.
The changes in detail:
* The current alternatives bits are moved to a separate file,
the SMP alternatives code is added there.
* The patch adds some new elf sections to the kernel:
.smp_altinstructions
like .altinstructions, also contains a list
of alt_instr structs.
.smp_altinstr_replacement
like .altinstr_replacement, but also has some space to
save original instruction before replaving it.
.smp_locks
list of pointers to lock prefixes which can be nop'ed
out on UP.
The first two are used to replace more complex instruction
sequences such as spinlocks and semaphores. It would be possible
to deal with the lock prefixes with that as well, but by handling
them as special case the table sizes become much smaller.
* The sections are page-aligned and padded up to page size, so they
can be free if they are not needed.
* Splitted the code to release init pages to a separate function and
use it to release the elf sections if they are unused.
Signed-off-by: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This seems to work for a short period of time, but when
used in conjunction with a userspace governor that changes
the frequency regularly, it's only a matter of time before
everything just locks up.
Signed-off-by: Dave Jones <davej@redhat.com>
Fix the code to disable freqs less than 2GHz in N60 errata.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The x86_model calculation also applies for family 6. early_cpu_detect
does the right thing, but generic_identify misses.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
powernow-k8: Let cpufreq driver handle affected CPUs
Let the cpufreq driver manage AMD Dual-Core CPUs being tied together.
Since cpufreq driver's affected CPUs data, cpufreq_policy->cpus, already
knows about which cores are tied together, powernow driver does not have
keep its internal data for every core. (even a pointer.. it will never
be called on) Telling cpufreq driver about cpu_core_map at init time is
sufficient.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Recent GDT changes broke the SMP boot sequence if the booting CPU is
numbered anything other than zero. There's also a subtle source of error
in that the boot time CPU now uses cpu_gdt_table (which is actually the GDT
for booting CPUs in head.S). This patch fixes both problems by making GDT
descriptors themselves allocated from a per_cpu area and switching to them
in cpu_init(), which now means that cpu_gdt_table is exclusively used for
booting CPUs again.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Matt Tolentino <metolent@snoqualmie.dp.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD SimNow!'s JIT doesn't like them at all in the guest. For distribution
installation it's easiest if it's a boot time option.
Also I moved the variable to a more appropiate place and make
it independent from sysctl
And marked __read_mostly which it is.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 CPU init code accesses freed init memory when booting a newly-started
processor after CPU hotplug. The cpu_devs array is searched to find the
vendor and it contains pointers to freed data.
Fix that by:
1. Zeroing entries for freed vendor data after bootup.
2. Changing Transmeta, NSC and UMC to all __init[data].
3. Printing a warning (once only) and setting this_cpu
to a safe default when the vendor is not found.
This does not change behavior for AMD systems. They were broken already
but no error was reported.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ignore clock frequencies below 2Ghz for CPU's detected with N60 errata bug.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch fixes the following compile error:
...
CC arch/i386/kernel/cpu/cpufreq/gx-suspmod.o
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c: In function 'gx_detect_chipset':
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: error: implicit declaration of function 'pci_match_id'
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: warning: comparison between pointer and integer
make[3]: *** [arch/i386/kernel/cpu/cpufreq/gx-suspmod.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
cpufreq init can be called when a CPU is set online.
Need to make powernow-k8's initialisation functions __cpuinit to
prevents oopses when a CPU is off/onlined on a AMD system
Cc: trenn@suse.de
Cc: mark.langsdorf@amd.com
Cc: davej@redhat.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
early_cpu_detect only runs on the BP, but this code needs to run
on all CPUs.
Looks like a mismerge somewhere. Also add a warning comment.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print bits for RDTSCP, SVM, CR8-LEGACY.
Also now print power flags on i386 like x86-64 always did.
This will add a new line in the 386 cpuinfo, but that shouldn't
be an issue - did that in the past too and I haven't heard
of any breakage.
I shrunk some of the fields in the i386 cpuinfo_x86 to chars
to make up for the new int "x86_power" field. Overall it's
smaller than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They previously tried to figure this out on their own.
Suggested by Venkatesh.
Cc: venkatesh.pallipadi@intel.com
Cc: davej@redhat.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define it for i386 too.
This is a synthetic flag that signifies that the CPU's TSC runs
at a constant P state invariant frequency.
Fix up the logic on x86-64/i386 to set it on all known CPUs.
Use the AMD defined bit to set it on future AMD CPUs.
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds configurable support for doublefault reporting on x86
add/remove: 0/3 grow/shrink: 0/1 up/down: 0/-13048 (-13048)
function old new delta
cpu_init 846 786 -60
doublefault_fn 188 - -188
doublefault_stack 4096 - -4096
doublefault_tss 8704 - -8704
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Provide basic support for the AMD Geode GX and LX processors.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stop deleting NT bit from EFLAGS. See arch/i386/kernel/head.S line 223, which
does something even better.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make GDT page aligned and page padded to support running inside of a
hypervisor. This prevents false sharing of the GDT page with other hot
data, which is not allowed in Xen, and causes performance problems in
VMware.
Rather than go back to the old method of statically allocating the GDT
(which wastes unneded space for non-present CPUs), the GDT for APs is
allocated dynamically.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I spotted 'main_lock' whilst grovelling through a vmlinux with objdump.
Even if it is static, it's a horrible name.
Signed-off-by: Dave Jones <davej@redhat.com>
What is the value shown in "cpu MHz" of /proc/cpuinfo when CPUs are capable of
changing frequency?
Today the answer is: It depends.
On i386:
SMP kernel - It is always the boot frequency
UP kernel - Scales with the frequency change and shows that was last set.
On x86_64:
There is one single variable cpu_khz that gets written by all the CPUs. So,
the frequency set by last CPU will be seen on /proc/cpuinfo of all the
CPUs in the system. What you see also depends on whether you have constant_tsc
capable CPU or not.
On ia64:
It is always boot time frequency of a particular CPU that gets displayed.
The patch below changes this to:
Show the last known frequency of the particular CPU, when cpufreq is present. If
cpu doesnot support changing of frequency through cpufreq, then boot frequency
will be shown. The patch affects i386, x86_64 and ia64 architectures.
Signed-off-by: Venkatesh Pallipadi<venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch moves away PMBASE reading and only performs it at
cpufreq_register_driver time by exiting with -ENODEV if unable to read
the value.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The attached patch introduces runtime latency measurement for ICH[234]
based chipsets instead of using CPUFREQ_ETERNAL. It includes
some sanity checks in case the measured value is out of range and
assigns a safe value of 500uSec that should still be enough on
problematics chipsets (current testing report values ~200uSec). The
measurement is currently done in speedstep_get_freqs in order to avoid
further unnecessary transitions and in the hope it'll come handy for SMI
also.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
speedstep-ich.c | 4 ++--
speedstep-lib.c | 32 +++++++++++++++++++++++++++++++-
speedstep-lib.h | 1 +
speedstep-smi.c | 1 +
4 files changed, 35 insertions(+), 3 deletions(-)
If a user has booted with 'quiet', some important messages don't
get displayed which really should. We've seen at least one case
where powernow-k8 stopped working, and the user needed a BIOS update
that they didn't know about.
Signed-off-by: Dave Jones <davej@redhat.com>
Thanks to LinuxICC (http://linuxicc.sf.net), a comparison of a u32 less
than 0 was found, this patch changes the variable to a signed int so that
comparison is meaningful.
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Linux invokes the AML _PDC method (Processor Driver Capabilities)
to tell the BIOS what features it can handle. While the ACPI
spec says nothing about the OS invoking _PDC multiple times,
doing so with changing bits seems to hopelessly confuse the BIOS
on multiple platforms up to and including crashing the system.
Factor out the _PDC invocation so Linux invokes it only once.
http://bugzilla.kernel.org/show_bug.cgi?id=5483
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Future versions of the Opteron processor may support
frequency transitions of 100 MHz, instead of the=20
current 200 MHz. This patch enables the powernow-k8
driver to transition to an odd FID code, indicating
a multiple of 100 MHz frequency.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch cleans up some error messages in the
powernow-k8 driver and makes them more understandable.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Fix the Intel cache detection code assumption that number of threads
sharing the cache will either be equal to number of HT or core siblings.
This also cleans up the code in general a bit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They report 40bit, but only have 36bits of physical address space.
This caused problems with setting up the correct masks for MTRR.
CPUID workaround for steppings 0F33h(supporting x86) and 0F34h(supporting x86
and EM64T). Detail info can be found at:
http://download.intel.com/design/Xeon/specupdt/30240216.pdfhttp://download.intel.com/design/Pentium4/specupdt/30235221.pdf
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to cpuid instruction in IA32 SDM-Vol2, when computing cpu model,
we need to consider extended model ID for family 0x6 also.
AK: Also added fixes/simplifcation from Petr Vandrovec
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Make cmpxchg generally available on the i386 platform.
- Provide emulation of cmpxchg suitable for uniprocessor if built and run on
386.
From: Christoph Lameter <clameter@sgi.com>
- Cut down patch and small style changes.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's widely seen a MCE non-fatal error reported after resume. It seems MCE
resume is lacked under ia32. This patch tries to fix the gap.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpu cache entries should be populated only when cpu is online and removed
when they are logically offlined.
Without which entries are not removed when cpu is offlined, or dont appear
when we boot with maxcpus=1 and then kick the rest of the cpus via echo 1
to the sysfs online file.
- Changed __devinit to __cpuinit for consistency.
- Changed sysfs_driver_register to register_cpu_notifier.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle 32-bit mtrr ioctls in the mtrr driver instead of the ia32
compatability layer.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If VMX feature is available in the CPU, this patch will make it visible in
the /proc/cpuinfo with the cpuid detection.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that prints the cache size assumes that L3 always lives in chipset
and is shared across CPUs. Which is not really true.
I think all the cachesizes reported by cpuid are in the processor itself.
The attached patch changes the code to reflect that.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make P6 MCA initialization code complaint with guidelines in IA-32 SDM
Vol3. Bank 0 control register should not be set by OS and clear status
registers on all banks on reset.
This will prevent false MCE alarms on the systems that has some non-MCE
information left-over in MC0_STATUS on reboot.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an accessor function for getting the per-CPU gdt. Callee must already
have the CPU.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The per-CPU initialization code is copying in bogus data into
thread->tls_array. Note that it copies &per_cpu(cpu_gdt_table, cpu), not
&per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TLS_MIN). That is totally broken
and unnecessary. Make the initialization explicitly NULL.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial internal version of Venki's cpuid(4) deterministic cache parameter
identification patch used static arrays of size MAX_CACHE_LEAVES. Final patch
which made to the base used dynamic array allocation, with this
MAX_CACHE_LEAVES limit hunk still in place.
cpuid(4) already has a mechanism to find out the number of cache levels
implemented and there is no need for this hardcoded MAX_CACHE_LEAVES limit.
So remove the MAX_CACHE_LEAVES limit from the routine which calculates the
number of cache levels using cpuid(4)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not sure how it slipped by, but here's a trivial typo fix for powernow.
Signed-off-by: Chris Wright <chrisw@osdl.org>
[ It's "nurter" backwards.. Maybe we have a hillbilly The Shining fan? ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD recently discovered that on some hardware, there is a race condition
possible when a C-state change request goes onto the bus at the same
time as a P-state change request.
Both requests happen, but the southbridge hardware only acknowledges the
C-state change. The PowerNow! driver is then stuck in a loop, waiting
for the P-state change acknowledgement. The driver eventually times
out, but can no longer perform P-state changes.
It turns out the solution is to resend the P-state change, which the
southbridge will acknowledge normally.
Thanks to Johannes Winkelmann for reporting this and testing the fix.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to use long long, not long when RMWing a MSR. I think
it's harmless right now, but still should be better fixed
if AMD adds any bits in the upper 32bit of HWCR.
Bug was introduced with the TLB flush filter fix for i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I checked with AMD and they requested to only disable it for family 15.
Also disable it for i386 too. And some style fixes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of these guys are simply not needed (pulled by other stuff
via asm-i386/hardirq.h). One that is not entirely useless is hilarious -
arch/i386/oprofile/nmi_timer_int.c includes linux/irq.h... as a way to
get linux/errno.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Via reading the code, my understanding is that powernow-k8 uses
preempt_disable to ensure that driver->target doesn't migrate across cpus
whilst it's accessing per processor registers, however set_cpus_allowed
will provide this for us. Additionally, remove schedule() calls from
set_cpus_allowed as set_cpus_allowed ensures that you're executing on the
target processor on return.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
get_cpu_vendor() no longer has any users in other files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some more assembler cleanups I noticed along the way.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 inline assembler cleanup.
This change encapsulates descriptor and task register management. Also,
it is possible to improve assembler generation in two cases; savesegment
may store the value in a register instead of a memory location, which
allows GCC to optimize stack variables into registers, and MOV MEM, SEG
is always a 16-bit write to memory, making the casting in math-emu
unnecessary.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 Inline asm cleanup. Use cr/dr accessor functions.
Also, a potential bugfix. Also, some CR accessors really should be volatile.
Reads from CR0 (numeric state may change in an exception handler), writes to
CR4 (flipping CR4.TSD) and reads from CR2 (page fault) prevent instruction
re-ordering. I did not add memory clobber to CR3 / CR4 / CR0 updates, as it
was not there to begin with, and in no case should kernel memory be clobbered,
except when doing a TLB flush, which already has memory clobber.
I noticed that page invalidation does not have a memory clobber. I can't find
a bug as a result, but there is definitely a potential for a bug here:
#define __flush_tlb_single(addr) \
__asm__ __volatile__("invlpg %0": :"m" (*(char *) addr))
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor fallout from my upcoming __attribute__((format(printf,x,y)))
patches. The variable 'result' is untouched, so this patch just removes
it.
Signed-off-by: Mika Kukkonen <mikukkon@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Ho-hum, did not notice there was more printf fixes for cpufreq (you
should see the amount I have for isdn and reiser ...). Sorry for noise.
Signed-off-by: Mika Kukkonen <mikukkon@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
speedstep_centrino.c:extract_clock() assumes the bus speed of 100MHz, which is
not true with latest laptops. Due to this assumption and due to the encoded
frequency check during initialization, speedstep-centrino driver fails even
on systems that has proper ACPI information to do the P-state transition.
The change below moves the centrino-speedstep detection to be used only
when table based P-state transition is done. For ACPI based P-state
transition, we skip the centrino_cpu identification, and as a result we
don't use the bus speed assumption in extract_clock. This change makes
speedstep-centrino work on Pentium-M based systems, which have more than 100MHz
bus speed.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The acpi-cpufreq driver does a P-state get after a P-state set
to verify whether set went through successfully. This test
is kind of redundant as set goes throught most of the times,
and the test is also expensive as a get of P-states can
take a lot of time (same as a set operation) as it goes
through SMM mode. Effectively, we are doubling the P-state
latency due to this get opertion.
momdule parameter "acpi_pstate_strict" restores orginal paranoia.
http://bugzilla.kernel.org/show_bug.cgi?id=5129
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix bug found by Grant Coady <lkml@dodo.com.au>'s autobuild setup.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We know that the randomisation slows down some workloads on Transmeta CPUs
by quite large amounts. We think it's because the CPU needs to recode the
same x86 instructions when they pop up at a different virtual address after
a fork+exec.
So disable randomization by default on those CPUs.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Otherwise a platform that supports ACPI based cpufreq
and boots up at lowest possible speed could stay there
forever. This because the governor may request max speed,
but the code doesn't update if there is no change in
speed, and it assumed the initial state of max speed.
http://bugzilla.kernel.org/show_bug.cgi?id=4634
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:740: warning: unused variable `vid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:739: warning: unused variable `fid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:743: warning: unused variable `vid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:742: warning: unused variable `fid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:746: `fid' undeclared (first use in this function)
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:746: `vid' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
powernow-k8.c:110: warning: `hi' may be used uninitialized in this function
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
can be encoded in the current driver's 4 bit frequency
field. This patch updates the driver to support Rev F
including 6 bit FIDs and processor ID updates.
This should apply cleanly whether or not the dual-core
bugfix I sent out last week is applied. I'd prefer
that both get applied, of course.
Signed-off-by: David Keck <david.keck@amd.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
each core be created in the _cpu_init function
call. The cpufreq infrastructure doesn't call
_cpu_init for the second core in each processor.
Some systems crashed when _get was called with
an odd-numbered core because it tried to
dereference a NULL pointer since the data
structure had not been created.
The attached patch solves the problem by
initializing data structures for all shared
cores in the _cpu_init function. It should
apply to 2.6.12-rc6 and has been tested by
AMD and Sun.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
powernow-k8.c: In function `query_current_values_with_pending_wait':
powernow-k8.c:110: warning: `hi' may be used uninitialized in this function
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new section called ".data.read_mostly" for data items that are read
frequently and rarely written to like cpumaps etc.
If these maps are placed in the .data section then these frequenly read
items may end up in cachelines with data is is frequently updated. In that
case all processors in an SMP system must needlessly reload the cachelines
again and again containing elements of those frequently used variables.
The ability to share these cachelines will allow each cpu in an SMP system
to keep local copies of those shared cachelines thereby optimizing
performance.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com>
Signed-off-by: Christoph Lameter <christoph@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There has been some discuss about solving the SMP MTRR suspend/resume
breakage, but I didn't find a patch for it. This is an intent for it. The
basic idea is moving mtrr initializing into cpu_identify for all APs (so it
works for cpu hotplug). For BP, restore_processor_state is responsible for
restoring MTRR.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dynamic pci id logic has been bothering me for a while, and now that
I started to look into how to move some of this to the driver core, I
thought it was time to clean it all up.
It ends up making the code smaller, and easier to follow, and fixes a
few bugs at the same time (dynamic ids were not being matched
everywhere, and so could be missed on some call paths for new devices,
semaphore not needed to be grabbed when adding a new id and calling the
driver core, etc.)
I also renamed the function pci_match_device() to pci_match_id() as
that's what it really does.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using CPU hotplug to support suspend/resume SMP. Both S3 and S4 use
disable/enable_nonboot_cpus API. The S4 part is based on Pavel's original S4
SMP patch.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean CPU states in order to reuse smp boot code for CPU hotplug.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trival patch for CPU hotplug. In CPU identify part, only did cleaup for intel
CPUs. Need do for other CPUs if they support S3 SMP.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make SEP init per-cpu, so it is hotplug safe.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make use of the 2 new macro set_debugreg and get_debugreg.
Signed-off-by: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64's cpu_khz is unsigned int and there is no reason why x86 needs to use
unsigned long.
So make cpu_khz unsigned int on x86 as well.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As mandated by the spec, disable timer around transitions.
From code by : Ken Staton <ken_staton@agilent.com
Signed-off-by: Dave Jones <davej@redhat.com>
The spec states that we have to do this, which is *horrid*.
Based on code from: Ken Staton <ken_staton@agilent.com>
Signed-off-by: Dave Jones <davej@redhat.com>
With the release of the dual-core AMD Opterons last week,
it's high time that cpufreq supported them. The attached
patch applies cleanly to 2.6.12-rc3 and updates powernow-k8
to support the latest Athlon 64 and Opteron processors.
Update the driver to version 1.40.0 and provide support
for dual-core processors.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
We have to recalibrate cpu_khz in order to use the current FID instead the max
FID since some BIOS do not put the processor at maximum frequency at POST.
Also, some BIOS will change the processor frequency at our back after cpu_khz
was calibrate. Finally, this will fix a long standing bug when we do
something like this:
# rmmod powernow-k7
# modprobe powernow-k7
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The speedstep-smi driver actually works on >=1 notebook with a
Pentium 4-M CPU where all other cpufreq drivers fail. Therefore,
allow speedstep-smi on P4Ms again, but warn users of likely failure
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The Pentium 4 - Ms (HT) with CPUID 0xF34 and 0xF41 seem to support
centrino-like enhanced speedstep; however, no "table" support is possible.
Therefore, put NULL entries into speedstep-centrino.c
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
num_cache_leaves is used in __devexit cache_remove_dev() and can therefore
not be __devinit.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove duplicated ifdef
- Make core_id match what Intel uses
- Initialize phys_proc_id correctly for non DC case
- Handle non power of two core numbers.
Fixes for both i386 and x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Last round hopefully of cpu_core_id changes hopefully fow now:
- Always initialize cpu_core_id for all CPUs, even when no dual core setup
is detected. This prevents funny /proc/cpuinfo output
- Do the same with phys_proc_id[] even when no HyperThreading - dito.
- Use the CPU APIC-ID from CPUID 1 instead of the linux virtual CPU number
to identify the core for AMD dual core setups.
Patch for i386/x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another large rollup of various patches from Adrian which make things static
where they were needlessly exported.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://bugme.osdl.org/show_bug.cgi?id=4426
vendor_id : AuthenticAMD
cpu family : 6
model : 10
model name : AMD Athlon(tm) XP
stepping : 0
cpu MHz : 2204.807
<snipped>
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 mmx fxsr sse pni syscall mmxext 3dnowext 3dnow
bogomips : 4358.14
We're marking bit 0 of extended function 0x80000001 cpuid as PNI support on
AMD processors, when it actually denotes x87 FPU present. Patch for i386
and x86_64 below.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable write combining for server works LE rev > 6 per
http://www.ussg.iu.edu/hypermail/linux/kernel/0104.3/1007.html
Signed-Off-By: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch to arch/i386/kernel/cpu/amd.c relies on the variable
cpu_core_id which is defined in i386/kernel/smpboot.c. This means it is
only present if CONFIG_X86_SMP is defined, not CONFIG_SMP (alternative
SMP harnesses won't have it, which is why it breaks voyager).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- broken sibling_map setup in x86_64
- grouping all the core and HT related cpuinfo fields.
We are reasonably sure that adding new cpuinfo fields after "siblings" field,
will not cause any app failure. Thats because today's /proc/cpuinfo
format is completely different on x86, x86_64 and we haven't heard of any
x86 app breakage because of this issue. Grouping these fields will
result in more or less common format on all architectures (ia64, x86 and
x86_64) and will cause less confusion.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the code greatly. Now uses the infrastructure from the Intel dual
core patch Should fix a final bug noticed by Tyan of not detecting the nodes
correctly in some corner cases.
Patch for x86-64 and i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch adds the support for Intel dual-core detection and displaying
the core related information in /proc/cpuinfo.
It adds two new fields "core id" and "cpu cores" to x86 /proc/cpuinfo and the
"core id" field for x86_64("cpu cores" field is already present in x86_64).
Number of processor cores in a die is detected using cpuid(4) and this is
documented in IA-32 Intel Architecture Software Developer's Manual (vol 2a)
(http://developer.intel.com/design/pentium4/manuals/index_new.htm#sdm_vol2a)
This patch also adds cpu_core_map similar to cpu_sibling_map.
Slightly hacked by AK.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to use the size_and_mask in set_mtrr_var_ranges(which is called
while programming MTRR's for AP's
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It doesn't make sense to only do this only for AMD K8.
This would support future CPUs with extended address spaces properly.
For i386 and x86-64
Cc: <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only display physical id/siblings when there are siblings or dual core.
In 2.6.11 I accidentially broke it and it was always displaying these
fields But for compatibility to all these /proc parsers around it is better
to do it in the old way again.
Noticed by Suresh Siddha
Cc: <Suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
